PVI Industries Btu-h GPH User Manual
SPECIFICATION FOR DOMESTIC WATER HEATERS
Condensing, Gas-Fired Water Heaters with Nickel-Plated Storage Tanks
Furnish and install the following POWER VT® gas water heater(s) as manufactured by PVI INDUSTRIES, INC of Fort
Worth, Texas.
Model Btu/h GPH Recovery Storage
Qty Number Input 40° to _____°F Tank
___ ____________ __________ ________ _______ gallons
___ ____________ __________ ________ _______ gallons
___ ____________ __________ ________ _______ gallons
Efficiency
The water heater will operate at a thermal efficiency of 94% when tested to ANSI Z21.10.3. The water heater will
comply with paragraph 7.2.4.4, the thermal efficiency and the standby loss requireme nts of ASHRAE 90.1-19 99.
Pressure Vessel and Heating Surfaces
The water heater will be a vertical fire tube design that is constructed and stamped in acco rdance with Section IV,
Part HLW of the ASME code. Both the storage and heating sections of the water heater will be National Board
Registered for a working pressure of 150 psi and will be pressure tested at 1-1/2 times working pressure. The fireside of
the heating surfaces will be of boiler-grade steel. The waterside of the heating tubes will be sealed in copper. The
heating tubes will be rolled, beaded, and seal welded into the tube sheets. The combustion side of the tube sh eet will be
insulated by a layer of ceramic fiber that will protect the tube sheet from both thermal stresses and failure that can result
from the accumulation of scale and precipitants.
Lining
The tank will be a plated with electroless nickel (EN). Plating will occur after the pressure vessel is completely
fabricated and all welding is completed. The EN plating will be a high-phosphorus (10%) and nonporous composition
suitable for submersion service (ASTM B733 standard ma y be used as a guideline). The finished lining will not req uire
sacrificial anode rods. For additional protection against galvanic corrosion, which ma y occur within the potable water
system, the EN plating may have a high-dielectric-strength polymer overcoat.
Burner and Venting
Combustion will be provided by an induced-draft power burner that can operate with as little as 4-1/2 inches water
column of gas pressure. The water heater will be UL listed for use with plastic v enting materials. The heater will be
capable of directly venting inlet air rated @ 120 equivalent feet and exhaust rated as f ollows: 4” vent - 50 e quivalent feet
on 1 MBtu/h model, 100 equivalent feet for other inputs; 6” vent – 39 0 equivalent feet on 1Mbtu/ h model, 500 equival ent
feet for other inputs.
The burner will be equipped with a gas train meeting the specifications of:
___ UL (standard equipment) ___ FM ___ IRI ___ Other ______________________
(continued)
PV 6149b 2/02 1
SPECIFICATION FOR DOMESTIC WATER HEATERS
Condensing, Gas-Fired Water Heaters with Nickel-Plated Storage Tanks
(continued)
Burner and Venting
Safety Controls
As a minimum
• a solid-state flame safeguard with pre-purge, programmable post-purge, and flame status indicating lights
• two immersion operating thermostats
• an immersion temperature limiting device
• a stack temperature limiting device
• an ASME- or AGA-rated temperature and pressure relief valve
• and options as selected on form PV 6147
The burner and all heater parts will have a one-year warranty. Storage tank will have a ten-year warranty covering
manufacturing or material defects, and/or the production of rusty water. Tank and heating surfaces will have a nonprorated, three-year warranty against failure due to scale buildup with no provisions for periodic cleaning for warranty
coverage. If indicated here, the heater will also have a _____ first year or ____ long-life service policy, which will cover
replacement labor and freight costs under certain conditions. This summary is not a warranty. Consult warranty and
policies for full details. Complete copies of all warranties and service policies, inclu ding all exclu sions and
conditions, will be presented to the owner as part of the submittal package.
The storage and heating sections will be completely factory packaged and plumbed, requiring only job site hookup to
utilities, venting, and potable water inlet and outlet. The heater will be insulated to meet current ASHRAE standards,
jacketed with powder-coated steel panels, and mounted on heavy-duty channel skids. The heater will fit properly in the
space provided and installation will conform to all local, state, and national codes.
Start up on the unit will be performed by factory trained and authorized personnel. A copy of the start up report will
be provided to the owner.
The heater will be UL or CGA listed. The water heaters will be manufactured by a company that has achieved
certification to the ISO 9001 International Quality System.
, the heater will be equipped with the following:
Warranty Summary
Finishing
Start Up
Quality Certification • Safety and Performance Standards
PV 6149b 2/02 2
Loading...