PVI Industries 1250N600A-TPO, 2500N600A-TPO, 3500N600A-TPO, 1500N600A-TPO, 1000N600A-TPO User Manual

TURBOPOWER® GAS/OIL  PACKAGED WATER HEATER

NICKELSHIELD

®

NICKEL-PLATED STORAGE TANK

TANK SERIES 600 GALLONS

Model

Number

Recovery gph 

40°- 120°F 40°- 140°F A B C J  HP

Input
Btu/h

Min. Inlet Flow

Gas Pressure

"W.C. 

#2 Oil

gph

Dimensions (inches)

750 N 600A-TPGO 750 600 600,000 4.5 4.3 46 6 1 31 1/2
1000 N 600A-TPGO 1000 800 800,000 6.0 5.7 46 8 1 31 1/2
1250 N 600A-TPGO 1250 1000 1,000,000 7.5 7.2 54 8 1 31 3/4
1500 N 600A-TPGO 1500 1200 1,200,000 7.5 8.6 54 8 1-1/4 31 1
2000 N 600A-TPGO 2000 1600 1,600,000 6.5 11.4 63 10 2 36 2
2500 N 600A-TPGO 2500 2000 2,000,000 8.0 14.3 65 10 2 36 2

 Recoveries based on 83% thermal efficiency. ASHRAE 90.1 compliant for efficiency and standby loss.
 "J" dimension is for the burner housing only. Gas train may exceed this dimension.
 Standard gas train.

* The information presented is for Natural gas 0.6 S.G.— For operation with propane (LP gas), consult factory.

Dimensions are in inches unless otherwise specified.
Higher inputs available. Consult the factory.
For standard and optional equipment, see form PV 6046.

Blower

Motor

Volt/Ph/

Amps

115/1∅/10
115/1∅/10
115/1∅/14
115/1∅/16
115/1/∅24
115/1∅/24

Shipping

Weight

lbs

2720
2760
2850
2930
3140
3260

* GAS PRESSURE REQUIREMENTS

SEE TABLE FOR MINIMUM PRESSURE BY MODEL NUMBER.

MAXIMUM STATIC INLET PRESSURE: 14" W.C.

FOR PRESSURES OTHER THAN LISTED, CONSULT FACTORY.

Pressure shown is for standard UL gas train. Additional controls

may increase pressure requirements.

VENTING REQUIREMENTS

-.02" TO -.06" W.C. (NEGATIVE PRESSURE)

ENTIRE VENT SYSTEM SHOULD NEVER BE SIZED BASED

UPON THE VENT CONNECTION DIAMETER EXCLUSIVELY.

FOR PROPER SIZING, CONSULT

THE NATIONAL FUEL GAS CODE UNDER “FAN-ASSISTED.”

PVI INDUSTRIES, LLC

FORT WORTH, TEXAS 76111

PV 5460 03/04

[phone]

* REAR ACCESS MODULE

MODEL PREFIX M L STD or OPTIONAL

750-1500 23" 8" OPTIONAL

2000-2500 23" 16" STANDARD

STANDARD ELECTRICAL REQUIREMENTS

CONTROL VOLTAGE: 120V, 1Ø, 60 HZ., 2 AMPS.
MOTOR VOLTAGE:
208V, 230V, AND 460V MOTORS ARE AVAILABLE BUT WILL
REQUIRE A SEPARATE 120V/2 amps CONTROL CIRCUIT OR AN
OPTIONAL CONTROL CIRCUIT TRANSFORMER.

PVI RESERVES THE RIGHT TO CHANGE THE DESIGN

 [phone]  www.pvi.com

AND SPECIFICATION WITHOUT NOTICE.

Product is patented in the U.S., Canada, and Mexico.