Pvg SRE 30X, EUROSTOVE SRE 30X 2 User Manual

2

YEARS

GUARANTEE

SRE 30x

3

2

5

4

>

1

MANUEL D'UTILISATION

GEBRAUCHSANWEISUNG

INSTRUCCIONES DE USO

OPERATING MANUAL

ISTRUZIONI D’USO

GEBRUIKSAANWIJZING

2

14

26

38

50

62

SRE 30x:
Eurostove SRE 301
Appliance SRE 302

3

Sous réserve de modification

2

Ändrungen vorbehalten

5

Nos reservamos el derecho de
hacer modificaciones

4

Subject to modifications

>

Sogetti a modifiche

1

Wijzigingen voorbehouden

Dear Sir, Madam,

Congratulations with your purchase of a portable domestic heater. You have

purchased a quality product, which will serve you for many years to come. This,

of course, if you use the heater correctly. Please read this user manual first, to

ensure maximum lifetime for your heater.

Your heater comes with a 24-month manufacturer’s warranty on all defects in

materials or workmanship.

We wish you a warm and comfortable time with your heater.

Yours sincerely,

PVG International b.v.

Customer Service Department

1 READ THE OPERATION MANUAL FIRST.

2 IN CASE OF ANY DOUBT, CONTACT YOUR DEALER.

4

38

1

2

8

MAIN COMPONENTS

Tank cover

A

Fuel gauge (back)

B

Overheat protection

C

device

Front panel

4

3

4

5

6

7

9

J

K

L

M

N

Inspection window

E

Warm air outlet

F

Fixed tank

G

Removable tank

H

Fuel cap

I

Handle

J

Control panel

K

Fuel filter

L

Fuel pump

M

Base plate

N

4

39

O

P

Q

R

Room thermistor

O

Power cord

P

Vent filter

Q

Air filter

R

GENERAL DIRECTIONS FOR USE

Below you will find the main steps to be taken for
using your heater. For more details, please refer to
Section A.

Remove all packaging materials (refer to Section A).

1

Fill the removable tank (refer to Section B).

2

Insert the plug into the wall-socket.

3

Ignite the heater using the

4

If required, change the temperature using the adjustment

5

buttons (refer to Section F).

Switch off the heater by pressing the key. (refer to Section

6

H).

• As a fire precaution, the tank must be filled either
when the heater has been switched off or in
another room than the room where the heater is
installed.

• Always ensure that the tank is closed properly
after filling it at a safe distance from all sources of
heat and open flames (see chapter B).

• The first time the heater is ignited it will smell like
“new” for a short time.

• Store all fuel containers with their original caps
and seals in a cool and dark place.

• Fuel ages. Use new fuel at the start of every
heating season.

• The use of Zibro Extra, Zibro Kristal or Zibro Bio as
a heating fuel assures you that you have a good
quality fuel.

• Before changing brands and/or types of fuel make
sure that the mobile heater first completely
empties all of the remaining fuel inside the

.

heater

key (refer to Section D).

4

40

WHAT YOU NEED TO KNOW IN ADVANCE

VENTILATE SUFFICIENTLY

Regardless of the model, you must always make sure that the heater is used in a
room large enough to enable the heater to be used safely without extra
ventilation. If the room is smaller than required, you must always open a door or
window slightly (ensuring an opening of approx. 2.5 cm). It is important that every
room where the heater is used has sufficient air intake and efficient air outflow

2

(both openings must have a minimum cross section of 50 cm
to the safety system are allowed, as that will invalidate the guarantee that the air
probe will work properly. Consult your dealer in case of doubt.

Especially for France: Your heater was designed to operate exclusively on fuel for
liquid fuel-operated mobile heaters in accordance with the Decr
and 18-07-2002. The use of other fuels is forbidden.
Ask your dealer or check our website for the addresses of our retailers.
The liquid fuel-operated mobile heater is intended as an extra heater, and not as a
continuous source of heat.

Especially for United Kingdom: Only use Class C1 paraffin fuel in accordance with
BS2869; Part 2, or equivalent.

). No modifications

ees of 08-01-1998

Only the use of the

correct fuel will ensure

safe, efficient, and

comfortable use of your

heater.

The user must comply with the following instructions for proper use:

DO NOT

- use the liquid fuel-operated mobile heater in caravans, boats, and vehicle cabins;

- use the liquid fuel-operated mobile heater in insuf
(consult the table of properties for the minimum dimensions of the room to be
heated), underground rooms and / or at a height of over 1500 metres;

- modify the heater safety features.

The use of this type of heating in public rooms is subject to prior regulatory
permission. Obtain proper information on this in advance.

ficiently ventilated rooms

THE RIGHT FUEL

Your heater has been designed for use with high-quality water-free pure paraffin
oil, such as Zibro Extra, Zibro Kristal or Zibro Bio. Only fuels of this kind will ensure
clean and proper burning. Lower quality fuel may result in:

E increased possibility of malfunctioning
E incomplete combustion
E reduced heater lifetime
E smoke and/or fumes
E deposits on the grid or mantle

Using the right fuel is therefore essential for safe, ef
of your heater.

ficient, and comfortable use

4

41

Damage and/or malfunctions of the heater due to the use of other than high­quality water-free pure parafine oil is not

Always refer to your local dealer for the right fuel for your heater.

covered by the warranty.

MANUAL

54321654321

A INSTALLING THE HEATER

E E E E E E

This transportation cap

is packed separately in

the box. Only this cap

ensures trouble-free

transportation of the

heater after use.

Store it well!

A

Carefully remove your heater from the box and check the contents.
In addition to the heater you also need to have:

E a transportation cap
E this operating manual

Keep the box and the packaging materials (Fig. A) for storage and/or
transportation.

Open the lid of the removable tank and remove the piece of car

Fill the removable tank as indicated in Section B.

The floor should be firm and completely level. Reposition the heater, when it
is not level. Do not try to correct the situation by placing books or other
goods under the heater

Insert the plug into the wall-socket (230 Volts - AC 50 Hz) and set the

correct time using the adjustment buttons (refer to Section C).

Your heater is now ready for use.

.

dboard.

B

B FILLING FUEL

Fill the removable tank in a suitable place since there can always be some spillage.
Follow the procedure below:

Make sure that the heater is switched off (refer to Section H).

C

Open the upper lid and lift the removable tank out of the heater (Fig. B).
Note: Some drops may leak from the tank. Put down the removable tank
(cap pointing upwards, handle on floor (Fig. C) and screw of

Fill the removable tank using a fuel pump (refer to fuel pump operation
instructions.) Make sure that it is in a higher position than the removable tank
(Fig. C). Insert the ribbed hose into the opening of the removable tank.

Check the removable tank fuel gauge while filling the tank (Fig. D). Stop
filling once the gauge indicates that the tank is full. Never overfill the tank,

D

especially not when the fuel is very cold (fuel expands when it heats up).

f the fuel cap.

Let the remaining fuel in the pump flow back into the jerrycan and carefully
remove the pump. Carefully screw the fuel cap back on the tank. Clean off
any spilled fuel.

empty full

4

42

Check whether the fuel cap is straight and tightened properly. Reinstall the

6

removable tank in the heater (cap down). Close the lid.

C SETTING THE CLOCK

It is only possible to set the correct time, when the heater is connected to mains.
Press the mode key once and the word TIME will appear on the display. Use the
+ and – buttons to enter the actual time.

When the heater has been unplugged (or after a power failure), the time needs

☞

to be set again.

D IGNITING THE HEATER (Auto restart)

When used for the first time, a new heater may give out some fumes for a short
while. You therefore have to provide extra ventilation.

Always ignite the heater with the button. Never use matches or a cigarette
lighter.

A little white smoke and smell during ignition is normal. Just press the button
to ignite the heater. The green power lamp inside the button will start to blink,
indicating that the ignition procedure is running. This will take about 2 or 3
minutes. Once the heater is really burning, the power lamp will light
continuously. This heater will restart automatically after a power cut when the
heater was in “on” position prior to power cut. This makes it possible to switch the
appliance on / off by interrupting / enabling the power supply (for instance
through a mobile phone switch).

4

E QUICK IGNITION

Sometimes you may know in advance that you will be manually switching on the
heater within 12 hours, but you do not want to wait 2-3 minutes (see chapter D) at
that particular moment. For these occasions this heater is equipped with the
“quick ignition” function. This function will prepare the heater such that at the
moment you want to switch on the heater that upon pressing the

heater will start within 5 seconds. To start the “QUICK IGNI.” function press the
quick ignition button.
In quick ignition mode:

The quick igition mode has to be enabled for at least 2-3 minutes before the
heater can be started.

- the electrical power consumption is 100 Watt

- the air at the outlet is slightly warmed

- is automatically cancelled when timer function is set

- is automatically switched off after 12 hours

- can be cancelled by pressing the QUICK IGNI. button
again. (The light will now be off).

F SETTING THE REQUIRED TEMPERATURE

The temperature setting can only be adjusted when the heater is burning. Use the
buttons + and – to adjust the temperature. The available temperature range is
+6°C minimum to +30°C maximum. The desired temperature is stored in the
memory and remains after a restart or power failure.

button the

43

G USING THE TIMER

The timer allows you to activate the heater at a certain time. In order to use the
timer, the correct actual time must have been set (refer to section C).

To set the timer:
Press the mode button twice and the word TIMER will appear on the display
the buttons + and – to set the time at which the heater has to start. Press the
button first, then press the TIMER button within 1 sec. The TIMER lamp switches
on and the heater is ready to start at the desired time.

H SWITCHING OFF THE HEATER

Press the button. The green lamp inside the button will switch off and the
heater stops within approximately 1 minute. A little white smoke and smell during
the extinguish period is normal.

. Use

I SAVE MODE

In the save mode the heater will switch off when the room temperature, as sensed
by the heater, rises 3°C above the set temperature. The save mode can be
activated with the button SAVE. The lamp in the button will switch on and the
heater will now switch off when the room temperature rises 3°C above the set
temperature. The heater will start again when the room temperature drops below
the set temperature.
The save mode can be cancelled by pushing the SAVE button again, the lamp
switches off.

J THE INFORMATION DISPLAY

The information display not only serves as an indicator of the (set) time and
temperature, it also indicates any malfunctioning of the heater. The code on the
information display tells you what is the matter:

CODE CAUSES WHAT TO DO

e - 0

e - 1

e - 2

e - 4

No flame during ignition. Check fuel, restart the heater.

Read section Q point 5.
Use correct fuel (see section “The
right fuel”).

Flame sensor failure Check fuel, restart the heater.

Read section Q point 5.
Use correct fuel (see section “The
right fuel”).

No flame after ignition. Check fuel, restart the heater.

Read section Q point 5.
Use correct fuel (see section “The
right fuel”).

Poor flame during normal burning. Check fuel, ventilate the room,

4

44

restart the heater. Read section Q
point 5.
Use correct fuel (see section “The
right fuel”).

e - 5

e - 6

Ignition temperature too low. Disconnected the mains plug and

restart.

Ignition temperature too high. Cool down, disconnect

the mains plug and restart.

e - 7 Wrong blower speed. Disconnect the mains plug and

restart.

e - 9 Tilt switch. Avoid shocks. The heater must

be levelled.

e -

e -

A

H

Room temperature > 35°C Ventilate the room and restart

the heater.

Electronics temperature > 60°C Ventilate the room and restart

the heater.

KL KEY LOCK. Push the button KEY LOCK 3

times to unlock the heater.

FUEL Out of fuel. Refill the removable tank. Check

if the fuel filter contains water.

TIME The heater shows the actual time Push the – and + buttons to

adjust the time.

TIMER The heater shows the set time for Push the – and + buttons to

timer adjust the set time when the

heater has to start.
The heater has been operating Switch the heater on again.
continuously for a period of 48 hours

and has switched itself off (refer to section K).

Always contact your dealer for any malfunctioning not listed above and/or when
the error keeps occuring after taking the corrective measure as described above.

K AUTOMATIC DEACTIVATION

This heater is equipped with a safety system that ensures that it switches off
automatically after 48 hours of continuous operation. The display will show:

. Switch on the heater by pressing the button.

L KEY LOCK

The key lock can be used to prevent children accidentally starting the heater. Press
the button KEY LOCK 3 times when the heater is off. The characters KL will appear
in the display. All keys are blocked now, the heater will not respond to any pressing
of the buttons. Press the button KEY LOCK again 3 times to release the key lock.
The status of the KEY LOCK is memorized and remains after a power interrupt.

M THE 'FUEL' INDICATOR

When low on fuel level the display will show “FUEL”. The heater will stop within
10-15 minutes. It will take some time after a refill before the heater is ready for
use again when the heater has used all its fuel.

4

45

321

Factory setting: switch

1 & 2 are in OFF position

(down).

N HIGH ALTITUDE ADJUSTMENT

The factory setting is for 0 – 500 meters above sea level. This setting needs to be
changed for higher altitudes to increase the blower speed and keep the
combustion correct.

Before changing the high altitude setting always remove the main’s plug!

Remove the two screws beside the front panel. A small block with 4 switches on
the main electronics board becomes visible. Always leave switch 3 and 4 in the
original position.

Altitude (m) Switch 1 Switch 2

0 - 500 OFF OFF

501 - 1000 OFF ON

1001 -1500 ON OFF

WARNING

Never insert the mains plug when fixed front panel is not fixed!

Fuel filter

air

vent

O MAINTENANCE

Switch off the heater, disconnect the plug from the mains and let it cool down,
before you start any maintenance work. Your heater needs hardly any maintenance.
It is, however, important that you clean the air filter and the vent filter with a
vacuum cleaner and a brush and the grid with a damp cloth, both on a weekly basis.
Remove the air filter occasionally and clean it with soapy water or with a vacuum
cleaner. Prior to reinstallation, make sure that the air filter cap has fully been dried.

Regularly inspect the fuel filter as well:

Remove the removable tank from the heater and remove the fuel filter
Some drops may leak from the filter; keep a cloth at hand.

Remove the dirt and water by gently tapping the fuel filter upside-down
against a hard surface. (Never clean it with water!)

Reinstall the fuel filter into the heater.

e recommend to remove dust and stains on the outside of the heater from time to

W
time with a damp cloth, otherwise these may cause stains that are hard to remove.

Do not remove any components yourself. Always contact your dealer for repairs.
When the power cord is damaged, it may only be replaced by an authorised

☞

engineer. Use a new original cord.

4

46

P STORAGE (END OF THE HEATING SEASON)

54321

At the end of the heating season, store the heater in a dust-free place in its
original packaging. Any unused fuel cannot be used the next heating season. We
therefore recommend that you burn up all fuel prior to storing. If there is still
some fuel left, do not throw it away, but dispose of it in accordance with the local
regulations for the disposal of domestic chemical waste.
Always start the new heating season with fresh fuel. When you start re-using the
heater follow the instructions again (starting from section A and as specified).

Q TRANSPORTATION

Take the following measures to avoid fuel leakage during the transportation of
the heater:

transportation cap

Let the heater cool down.

Remove the removable tank from the heater and remove the fuel filter.
Some drops may leak from the filter; keep a cloth at hand. Store the fuel filter
and the removable tank outside the heater.

Place the transportation cap into the position of the fuel filter. Press it tight.
The transportation cap will, as much as possible, prevent oil leakage from the
heater during transport.

Always move the heater in an upright position.

Make the fixed tank empty with a fuel pump before transportation or in case
of wrong or dirty fuel. First remove the fuel filter and then insert the fuel
pump into the empty fixed tank. Follow the same procedure if the fuel tank
contains water.

R SPECIFICATIONS

IGNITION ELECTRICAL

FUEL PARAFFIN

3

4

SUITABLE SPACE MIN-MAX 40 - 120 m

HEATING CAPACITY MIN-MAX 1 kW (83 g/h) 3.0 kW (250 g/h)

MAINS 230 V~ / 50 Hz

ELECTRIC CONSUMPTION BURNING 22 W

ELECTRIC CONSUMPTION IGNITION 660 W

ELECTRIC CONSUMPTION
QUICK IGNITION MODE

WEIGHT 10 kg

FUSE RATING 5 A / AC 250 V / 5 X 20 mm

DIMENSIONS (HxWxD) 45.5 x 40 x 30.7 cm

ACCESSORIES TRANSPORTATION CAP

REMOVABLE TANK CAPACITY 5 LITRES

BURNING TIME PER TANK
(100% CAPACITY)

100 W (heater not burning)

16 h

Specified values are indicative

47

S WARRANTY PROVISIONS

7

65432

1

Your heater comes with a 24-month warranty starting on the date of purchase.
Within this period all defects in material or workmanship will be repaired without
any charge. The following provisions shall apply regarding this warranty:

We expressly dismiss all other claims for damages, including consequential
damages.

Any repairs or replacements of components within the term of warranty will
not result in an extension of the term of warranty.

The warranty shall no longer apply, when the heater has been modified,
non-original parts have been used, or when it is repaired by third parties.

The warranty shall not apply to parts that are subject to normal wear.

The warranty shall only apply, when you present the original, dated proof of
purchase, provided no changes have been made to it.

The warranty shall not apply to damages caused by actions not in compliance
with this operating manual, neglect, and the use of an incorrect type of fuel,
or fuel past its use-by date. The use of incorrect fuel can even be dangerous*.

Transportation costs and the risks involved during the transportation of the
heater or heater components shall always be at the expense of the purchaser.

In order to avoid unnecessary costs, we recommend that you always read this
operating manual carefully first. In case they offer no solution, please take the
heater to your dealer for repair.

* Highly inflammable substances may induce uncontrollable burning, causing flames to break out. Should this
happen, never try to move the heater, but always switch off the heater immediately. In case of emergency you
may use a fire extinguisher, but only a type B extinguisher: a carbon dioxide or powder extinguisher.

11 TIPS FOR SAFE USE

1 This appliance is not intended for use by persons (including children) with

reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concer
ning use of the appliance by a person responsible for their safety.

2 Do not move the heater when it is burning or still hot. Do not refill nor

service the heater when it is burning or still hot.

3 Position the front of the heater at a distance of minimum 1.5 metres

from walls, curtains, and furnitur

4 Do not use the heater in dusty rooms or places with strong draughts. In

either situation you will not have optimum burning. Do not use the
heater in the immediate surrounding of a bath, a shower or a
swimmingpool.

5 Switch off the heater, before you leave or go to sleep. Unplug the

heater as well, when you go away for a longer period of time
(e.g. holidays).

e.

-

4

48

6 Store and move fuel only in suitable tanks and jerrycans.
7 Make sure that the fuel is not exposed to heat or extreme temperature

changes. Always store the fuel in a cool, dr
will affect the quality).

8 Never use the heater in places where harmful gasses or fumes may be

present (e.g. exhaust gasses or paint fumes).

9 Beware that the grid of the heater becomes hot. If the appliance is

covered there is a risk of fir

10 Always make sure that there is sufficient ventilation.
11 Children should be supervised to ensure that they do not play with the

appliance.

aste electrical products should not be disposed with household waste. Please

W
recycle where facilities exist. Check with your local authority or retailer for
recycling advice.

e.

y and dark place (sunlight

4

49

DISTRIBUTED IN EUROPE BY PVG INTERNATIONAL BV

i ÖSTERREICH

PVG Austria V

ertriebsgmbH
Salaberg 49
3350 HAAG
tel: [phone]
fax: [phone]
email: [e-mail]

e BELGIË

PVG Belgium NV/SA
Industrielaan 55
2900 SCHOTEN
tel:

[phone]
fax: [phone]
email: [e-mail]

q SCHWEIZ

PVG Schweiz AG
Salinenstrasse 63
4133 PRATTELN
tel:

[phone]
fax: [phone]
email: [e-mail]

2 DEUTSCHLAND

PVG Deutschland GmbH
Siemensstrasse 31
47533 KLEVE
tel:

0800 - 9427646
fax: [phone]
email: [e-mail]

4 UNITED KINGDOM

Scott Brothers Ltd.
The Old Barn, Holly House Estate
Cranage, Middlewich, CW10 9L

T UK
tel.: [phone]
fax: [phone]
email: [e-mail]

> ITALIA

PVG Italy SRL
Via Niccolò Copernico 5
50051 CASTELFIORENTINO (FI)
tel:

[phone]
fax: [phone]
email: [e-mail]

u NORGE

Appliance A/S
Gefionsvej 7
DK-3400 HILLERØD
tel:

[phone]
fax: [phone]
email: [e-mail]

1 NEDERLAND

PVG International B.V.
P.O. Box 96
5340 AB OSS
tel: [phone]
fax: [phone]
email: [e-mail]

6 DANMARK

Appliance A/S
Gefionsvej 7
DK-3400 HILLERØD
tel: [phone]
fax: [phone]
email: [e-mail]

5 ESPAÑA

PVG España S.A.
Pol. Ind. San José de Valderas II
Comunidad ”La Alameda”
C/ Aurora Boreal, 19
28918 LEGANÉS (Madrid)
tel: [phone]
fax: [phone]
email: [e-mail]

3 FRANCE

PVG France SARL
4, Rue Jean Sibélius

. 185

B.P
76410 SOTTEVILLE SOUS LE VAL
tel: [phone]
fax: [phone]
email: [e-mail]

FFIINN

SUOMI

Appliance A/S
Gefionsvej 7
DK-3400 HILLERØD
tel: [phone]
fax: [phone]
email: [e-mail]

9 PORTUGAL

Gardena, Lda
Recta da Granja do Marquês
ALGUEIRÃO
2725-596 MEM MARTINS
tel: + 35 21 92 28 530
fax:

+ 35 21 92 28 536
email: [e-mail]

: POLSKA

PVG Polska Sp. z. o. o.

ścielna 110

ul. Ko
26-800 Białobrzegi
tel:

[phone]
fax: [phone]
email: [e-mail]

= SVERIGE

Appliance A/S
Gefionsvej 7
DK-3400 HILLERØD
tel: [phone]
fax:

[phone]
email: [e-mail]

y SLOVENIJA

Monteko d.o.o.
Neubergerjeva 4
1000 Ljubljana
tel: [phone]
fax: [phone]
email: [e-mail]

TTRR

TURKEY

PVG Is›tma Klima So¤utma Ltd.fiti.

Tepekule is merkezi
Anadolu Cad. No: 40 K:3 D:306
35010 BA

YRAKLI/IZMIR
tel: + 90 232 461 51 01
fax: + 90 232 461 51 85
email: [e-mail]

PVG Traffic avg c 090522 man_SRE30x