112P™/ 115P
™
· Powered speaker system · Operations Manual
For more information on other great PVDJ products, go to your local PVDJ dealer or online at www.pvdj.com.
2
Intended to alert the user to the presence of uninsulated dangerous voltage within the products
enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
Intended to alert the user of the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the product.
CCAAUUTTIIOONN
: Risk of electrical shock DO NO T OPEN!
CCAAUUTTIIOONN
: To reduce the risk of electric shock, do not remove cover. No user serviceable parts inside.
Refer servicing to qualified service personnel.
WWAARRNNIINNGG
: To prevent electrical shock or fire hazard, do not expose this appliance to rain or moisture.
Before using this appliance, read the operating guide for further warnings.
Este smbolo tiene el propsito, de alertar al usuario de la presencia de (voltaje) peligroso sin
aislamiento dentro de la caja del producto y que puede tener una magnitud suficiente como para
constituir riesgo de descarga elØctrica.
Este smbolo tiene el propsito de alertar al usario de la presencia de instruccones importantes sobre la
operacin y mantenimiento en la informacin que viene con el producto.
PPRREECCAAUUCCIIOONN
: Riesgo de descarga elØctrica °NO ABRIR!
PRECAUCION: Para disminur el riesgo de descarga elØctrica, no abra la cubierta. No hay piezas
œtiles dentr o. Deje todo mantenimiento en manos del personal tØcnico cualificado.
AADDVVEERRTTEENNCCIIAA
: Para evitar descargas elØctricas o peligro de incendio, no deje expuesto a la lluvia o
humedad este aparato Antes de usar este aparato, Iea mÆs adv ertencias en la gua de operacin.
Ce symbole est utilisØ dans ce manuel pour indiquer lutilisateur la prØsence dune tension dangereuse
pouvant Œtr e damplitude suffisante pour constituer un risque de choc Ølectrique.
Ce symbole est utilisØ dans ce manuel pour indiquer lutilisateur quil ou quelle trouvera dimportantes
instructions concernant lutilisation et lentretien de lappareil dans le paragraphe signalØ.
AATTTTEENNTTIIOONN
: Risques de choc Ølectrique N E PAS OUVRIR!
AATTTTEENNTTIIOONN
: Afin de rØduire le risque de choc Ølectrique, ne pas enlever le couvercle. Il ne se trouve
lintØrieur aucune piŁce pouvant Œtr e reparØe par lutilisateur. Confiez Ientretien et la rØparation de
lappareil un rØparateur Peavey agrØØ.
AAVVEERRTTIISSSSEEMMEENNTT
: Afin de prØvenir les risques de dØcharge Ølectrique ou de feu, nexposez pas cet
appareil la pluie ou lhumiditØ. Avant dutiliser cet appareil, lisez attentivement les avertissements
supplØmentaires de ce manuel.
Dieses Symbol soll den Anwender vor unisolierten gefhrlichen Spannungen innerhalb des Gehuses
warnen, die von Ausreichender Strke sind, um einen elektrischen Schlag verursachen zu knnen.
Dieses Symbol soll den Benutzer auf wichtige Instruktionen in der Bedienungsanleitung aufmerksam
machen, die Handhabung und Wartung des Produkts betreffen.
VVOORRSSIICCHHTT
: Risiko Elektrischer Schlag! Nicht ffnen!
VVOORRSSIICCHHTT
: Um das Risiko eines elektrischen Schlages zu vermeiden, nicht die Abdeckung enfernen. Es
befinden sich keine Teile darin, die vom Anwender repariert werden knnten. Reparaturen nur von
qualifiziertem Fachpersonal durchfhren lassen.
AACCHHTTUUNNGG
: Um einen elektrischen Schlag oder Feuergefahr zu vermeiden, sollte dieses Gert nicht dem
Regen oder Feuchtigkeit ausgesetzt werden. Vor Inbetriebnahme unbedingt die Bedienungsanleitung lesen.
3
IIMMPPOORRTTAANNTT SSAAFFEETTYY IINNSSTTRRUUCCTTIIOONNSS
WWAARRNNIINNGG
:When using electrical products, basic cautions should always be followed, including the following:
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any of the ventilation openings. Install in accordance with manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers)
that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one
wider than the other. A grounding type plug has two blades and a third grounding plug. The wide blade or third prong is
provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the
obsolete outlet.
10. Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point
they exit from the apparatus.
11. Note for UK only: If the colors of the wires in the mains lead of this unit do not correspond with the terminals in your
plug‚ proceed as follows:
a) The wire that is colored green and yellow must be connected to the terminal that is marked by the letter E‚ the earth
symbol‚ colored green or colored green and yellow.
b) The wire that is colored blue must be connected to the terminal that is marked with the letter N or the color black.
c) The wire that is colored brown must be connected to the terminal that is marked with the letter L or the color red.
12. Only use attachments/accessories provided by the manufacturer.
13. Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a
cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
14. Unplug this apparatus during lightning storms or when unused for long periods of time.
15. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any
way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
16. Never break off the ground pin. Write for our free booklet “Shock Hazard and Grounding.” Connect only to a power
supply of the type marked on the unit adjacent to the power supply cord.
17. If this product is to be mounted in an equipment rack, rear support should be provided.
18. Exposure to extremely high noise levels may cause a permanent hearing loss. Individuals vary considerably in susceptibility to noise-induced hearing loss, but nearly everyone will lose some hearing if exposed to sufficiently intense noise
for a sufficient time. The U.S. Government’s Occupational Safety and Health Administration (OSHA) has specified the
following permissible noise level exposures:
Duration Per Day In Hours Sound Level dBA, Slow Response
890
692
495
397
2100
1 1⁄2 102
1105
1⁄2 110
1⁄4 or less 115
According to OSHA, any exposure in excess of the above permissible limits could result in some hearing loss. Ear plugs or protectors to the
ear canals or over the ears must be worn when operating this amplification system in order to prevent a permanent hearing loss, if exposure
is in excess of the limits as set forth above. To ensure against potentially dangerous exposure to high sound pressure levels, it is
recommended that all persons exposed to equipment capable of producing high sound pressure levels such as this amplification system be
protected by hearing protectors while this unit is in operation.
SSAAVVEE TTHHEESSEE IINNSSTTRRUUCCTTIIOONNSS!!
4
111155PP™™//111122PP
™™
Thank you for purchasing the PVDJ 112P/115P these powered enclosures featur a bi-amped power section that provides
200 Watts peak dynamic power for the woofer and 70 Watts peak dynamic power for the compression driver tweeter, both
with Peavey-exclusive DDT™compression. Offering a 15" heavy duty woofer and a 1.4” compression driver, the 112P/115P
provides an XLR and 1/4"phone combo jack, with mic/line switchable level, balanced input with volume control and a
pair of 1/4" phone jack inputs with concentric volume controls. Up to three line level input signals can be mixed
together, or one mic-level, and two line-level signals mixed.
It is very important that you ensure the PVDJ 112/115P has the proper AC line voltage supplied. You can find the proper
voltage printed next to the IEC line (power) cord on the rear panel of the unit. Please read this guide carefully to ensure
your personal safety as well as the safety of your equipment.
FFeeaattuurreess
·· BBii--aammpplliiffiieedd ppoowweerreedd ssyysstteemm wwiitthh 227700 WW ttoottaall ppeeaakk ddyynnaammiicc ppoowweerr!!
·· BBootthh ppoowweerr aammppss hhaavvee DDDDTT ccoommpprreessssiioonn
·· 1155"" hheeaavvyy dduuttyy wwooooffeerr wwiitthh 22--33//88"" vvooiiccee ccooiill aanndd 5500 oozz.. mmaaggnneett
·· 11..44"" ttiittaanniiuumm ccoommpprreessssiioonn ddrriivveerr
·· PPeeaakk SSPPLL uupp ttoo 112200 ddBB wwiitthh mmuussiicc
·· CCoommbboo jjaacckk wwiitthh 11//44"" TTRRSS aanndd ffeemmaallee XXLLRR mmiicc-- oorr lliinnee--lleevveell bbaallaanncceedd iinnppuutt
·· TTwwoo 11//44"" pphhoonnee jjaacckk iinnppuuttss wwiitthh ccoonncceennttrriicc lleevveell ccoonnttrroollss
·· IInnppuutt mmiixxiinngg bbuuiilltt--iinn
·· MMoollddeedd--iinn hhoorrnn wwiitthh eexxcceeppttiioonnaallllyy ssmmooootthh rreessppoonnssee aanndd ppaatttteerrnn ccoonnttrrooll
·· TToopp aanndd ssiiddee hhaannddggrriippss
·· PPoollee mmoouunntt mmoollddeedd--iinn
·· TToopp aanndd bboottttoomm ffllyyiinngg ppooiinntt iinnsseerrttss
DDeessccrriippttiioonn
The PVDJ 112P/115P are powered, bi-amplified, two-way speaker system engineered to provide very high levels of
performance in a compact powered loudspeaker. Capable of up to 120 dB peak SPL, this system can pump out a lot of
sound. The enclosure utilizes tough polypropylene in an injection-molded plastic trapezoidal form, with a coated steel
grille to offer an attractive yet-durable powered speaker system.
This two-way powered system is comprised of a 200 W dynamic peak power amplifier driving a 15" heavy duty woofer.
The 1.4” compression driver is driven by a 70 W peak dynamic power amplifier and features a titanium diaphragm
coupled to an extremely smooth and well-controlled constant directivity horn (with a coverage pattern of 90˚ by 40˚) that
is molded integrally into the enclosure.
A balanced input to the preamp/EQ electronics consists of one combo female XLR and 1/4" TRS phone jack. It is
switchable between mic-level and line-level sensitivity. Two 1/4" phone jack inputs are controlled in level by a concentric
pair of level controls. All three inputs can be mixed in any ratio.
The power amplifiers providing the bi-amplification are low-distortion units providing 150 W continuous RMS into the
nominal 8 Ohm load of the woofer, and a 50 W continuous RMS into the nominal 8 Ohm load of the tweeter. They were
selected for their reliability and superb musical performance capability. Both amplifiers feature our patented DDT
™
compression, which virtually eliminates audible power amplifier clipping.
A molded-in handle provides both comfort and ease of transportation.
EENNGGLLIISSHH
5
((11)) FFUUSSEE
The unit is AC power line fuse protected from overloads and fault conditions with an ABC-type fast-blow 5
Amp fuse. This fuse is located within the cap of the fuse holder. If the fuse fails, THE FUSE MUST BE
REPLACED WITH THE SAME TYPE AND VALUE IN ORDER TO AVOID DAMAGE TO THE EQUIPMENT AND TO
PREVENT VOIDING THE WARRANTY. If the unit repeatedly blows fuses, it should be taken to a qualified
service center for repair.
((22)) IIEECC PPOOWWEERR CCOORRDD CCOONNNNEECCTTIIOONN
This receptacle is for the IEC line cord (supplied) that provides AC power to the unit.
Never break off the ground pin on any equipment. It is provided for your safety. If the outlet
used does not have a ground pin, a suitable grounding adapter should be used and the third
wire should be grounded properly. To prevent the risk of shock or fire hazard, always be sure
that the mixer and all other associated equipment are properly grounded.
((33)) OONN--OOFFFF SSWWIITTCCHH
This rocker switch supplies AC power to the PVDJ 112P and 115P when switched to the ON position
AApppplliiccaattiioonnss
The PVDJ 112P and 115P have a variety of applications such as sound reinforcement, public address, side
fill system, karaoke or musical playback.
A typical signal source for the line-level inputs of the PVDJ 112P and 115P would be a sound reinforcement
mixing console (mixer) or the output from a CD player, Minidisc player or tape deck. A dynamic
microphone can be connected and used as well.
RR EE AA RR PP AA NN EE LL
1 3
2
6
((44)) PPOOWWEERR//CCLLIIPP LLEEDD
Illuminates GREEN when the electronics receive power (when the Power switch (3) is On). Illuminates RED
when amplifier clipping is occurring or the unit has tripped the thermal protection system.
((55)) PPRRIIMMAARRYY IINNPPUUTT ((CCHHAANNNNEELL 11))
The primary input is switchable between line-level and mic-level input. The line-level input is of the
medium impedance balanced type, and when switched to mic-level it is of a typical low-Z mic input
impedance. Jack (5) is a combo female XLR and 1/4" TRS connector.
((66)) PPAADD
Switches the sensitivity of Channel 1 from line-level to mic-level sensitivity. Pushed all the way in, the
sensitivity is set for line-level input signals, and when the white tab is closer to the front panel, the
sensitivity is increased by 30 dB so it is suitable for mic-level signals.
((77)) VVOOLLUUMMEE
Controls the gain (level) of the Primary Input (5), Channel 1, of the powered speaker system. It is used to
directly set the system output level for the Channel 1 input signal.
((88)) SSEECCOONNDDAARRYY IINNPPUUTTSS,, CCHHAANNNNEELL 22 && 33
These consist of 1/4" unbalanced phone jacks for line-level signals, with medium input impedance.
((99)) CCOONNCCEENNTTRRIICC VVOOLLUUMMEE,, CCHHAANNNNEELL 22 && 33
Controls the gain (level) of Channel 2 & 3 inputs. Can be used in conjunction with the Channel 1 volume
control (7) to mix three line-level signals together, or two line-level signals and one mic-level signal.
4
98
6
7
5
FF RR OO NN TT PP AA NN EE LL
7
OO PP EE RR AA TT II NN GG II NN SS TT RR UU CC TT II OO NN SS
CAUTIONS
The unit must be disconnected from the AC power source before any work is done on it. Refer all servicing
to qualified service personnel.
The heat sink on the back plate can become hot to the touch. Do not block or cover the heat sink from
ventilation.
Be sure to keep the microphone away from the front of the speaker after switching the mic sensitivity pad
to the OUT position and while setting the microphone level or very loud feedback will occur! Damage to
the system is likely if this occurs!
DO NOT connect the inputs of the 112P and 115P to the output of a power amplifier. The inputs are meant
to be driven from a line-level strength signal.
DO NOT remove the protective metal grille.
Warning: The PVDJ 112P and 115P are very efficient and powerful! This sound system can permanently
damage hearing! Use extreme care setting the overall maximum loudness!
The apparent sound level of the PVDJ 112P and 115P can be deceiving due to its clear, clean sound output.
The lack of distortion or obvious distress can make the sound level seem much lower than it actually is.
This system is capable of SPL in excess of 120 dB at 1 M from the speaker!
GGeettttiinngg AACC PPoowweerr TToo TThhee PPVVDDJJ 111122PP aanndd 111155PP
The PVDJ 112P and 115P come with an 8-foot IEC connection AC power cord. If you are using an extension cord
or power strip with this powered speaker, make sure it is of good quality and of a sufficient current capacity to
maintain safety and maximize the power output capability of the PVDJ 112P or 115P. Do not connect any other
device to the same extension cord that the PVDJ 112P or 115P are connected to.
SSppeecciiaall NNoottee ffoorr PPeerrmmaanneenntt IInnssttaallllaattiioonn
When installing the PVDJ 112P or 115P, AC power runs will be used and a certified electrician should be
consulted to be sure that all AC wiring complies with local codes and regulations. It is also advisable to
use a cable clip properly affixed to the cabinet to strain relief the IEC power cord connected to the
amplifier module at (2) so the power cord cannot be pulled out or vibrate loose.
UUssee ooff PPVVDDJJ 111122PP aanndd 111155PP wwiitthh aa SSuubbwwooooffeerr
The built-in pole adapter allows use with any sub that has a pole adapter with a diameter of 1-3/8"
GGeettttiinngg aa SSiiggnnaall ttoo tthhee PPVVDDJJ 111122PP aanndd 111155PP
There are a variety of ways to input a signal to the PVDJ 112P and 115P.
The primary input (5) provides either a balanced mic- or line-level input, allowing the use of a 1/4" phone
plug, either a standard single-ended (tip-sleeve) plug or a balanced TRS (tip-ring-sleeve) type plug OR a
male XLR plug. Then there are two line-level unbalanced 1/4" phone jacks that can be mixed in with the
primary input.
Do not connect cables to the jacks while the unit is ON and the Volume is turned up!
While a standard single-ended 1/4" phone plug-equipped cable will work well and the balanced input
circuitry of the primary input (5) will provide some interference rejection, a balanced cable using either the
balanced TRS 1/4" phone plug or the XLR plug will provide superior interference rejection and
performance. Sometimes, with difficult interference problems, it will be helpful to lift the shield ground on
a balanced cable at the 112P/115P end only. Check any input changes carefully, always turning the volume
control down before plugging and unplugging cables.
8
Use of high quality, premium cables is recommended for the PVDJ 112P and 115P, as these usually have
better shielding and materials and will provide greater long-term reliability. It is usually a good idea to
leave some slack at the input to the 112P and 115P and also to tape the cables down or run them under a
cable guard to avoid anyone tripping over them or pulling the 112P and 115P over when they are stand
mounted.
VVoolluummee CCoonnttrrooll AAddjjuussttmmeenntt
The 112P and 115P are equipped with volume controls to facilitate use in many different applications.
With the volume control adjusted fully clockwise, gain is at maximum and the input sensitivity is 0.375 V
RMS for full-rated output. When driving the 112P or 115P from a mixer, it may be advantageous to reduce
the input sensitivity by turning the volume control to the halfway point. The 112P or 115P will now more
closely match a typical power amp.
If the mixing board indicates clipping of its output signals, then all of the 112P or 115P power capabilitys
are not being utilized cleanly. Clipping the signal before it gets to the 112P or 115P are not optimal. In that
case, reduce the mixer output level and turn up the volume control on the 112P or 115P.
The amplifiers in the 112P and 115P are equipped with DDT
™
and an LED indicator to show that DDT™has
engaged. If the sound seems heavily compressed, check this indicator; and if it is blinking RED more than
occasionally, then the drive level from the mixer (or the volume control on the 112P or 115P) needs to be
reduced.
When first turning on the sound system, switch on all upstream electronics first, then the 112P or 115P
with its volume control fully counterclockwise (all the way down). Begin checking levels with the mixer
output level controls all the way down, and bring them up slowly with the 112P or 115P volume control set
to the desired setting (halfway up recommended to start).
MMiicc//LLiinnee PPaadd AAddjjuussttmmeenntt
The mic/line pad (6) provides for the increased gain needed for microphone use into the primary input
(5). Use a straightened paperclip or small screwdriver to reach through the hole in the rear panel where
the recessed tab is to set its position. Set the Mic/Line Pad to “in,” or the white tab furthest from the
panel, for line-level signal use, and set it “out,” or closest to the panel, for mic-level use. The unit is
shipped with the tab in the line-level position. It is recessed behind the panel so that the gain can not be
inadvertently increased during transport or set-up.
Due to the 30 dB of extra gain that this switch provides, DO NOT leave it in the “out” position for line level
use! This will result in input-stage clipping of the 112P or 115P and cause unnecessary distortion.
MMiixxiinngg SSiiggnnaallss UUssiinngg tthhee VVoolluummee KKnnoobbss
The gain of all three channels can be adjusted independently from the other channels via the volume
knobs (7) and (9). Channel 1 can be used for either line-level signals or as a mic input, and mixed with two
other line-level signals.
The 112P and 115P have plenty of gain, so do not overload the speaker system preamp inputs by driving
them with a signal that is too hot. Full output mixer levels well in excess of 0 dB will not going to be
necessary to drive the unit to full power capacity.
TTRROOUUBBLLEESSHHOOOOTTIINNGG
NNoo OOuuttppuutt aatt AAllll
First, make sure the unit has AC power and is turned ON. Make sure the Power/Clip LED (4) is illuminated
Green. If not, make certain the ON/OFF switch (3) is in the ON position and check the IEC power cord
connection (2) by ensuring it is fully engaged and seated. Make certain the AC line cord is plugged into a
working AC outlet. Finally, check the fuse (1). (See the Rear Panel: Fuse section, for safety instructions.)
9
Once assured your unit is getting AC power, check that the PVDJ 112P or 115P are getting a signal. Temporarily
disconnect the cable running to its inputs and connect it to some other device capable of reproducing the signal
(i.e., a power amp and speaker). If this produces a signal, make sure that all Volume controls being used have
been turned up to a satisfactory level (one-third to halfway).
If the PVDJ 112P or 115P have been subjected to direct sunlight or excessive heat, the built-in thermal
protection may have been triggered. The power/clip LED will be illuminated RED if this is the case. If so, turn off
the PVDJ 112P or 115P and let it cool for a sufficient amount of time.
If there is still no output, contact your authorized Peavey dealer or the Peavey International Service Center.
HHuumm oorr BBuuzzzz
If the PVDJ 112P or 115P is producing a hum or buzz, this can be AC outlet related. Try plugging the PVDJ
112P or 115P into a different AC outlet. Sometimes, if a different circuit (breaker) is used for the mixer and
the PVDJ 112P or 115P, it can cause hum problems.
Ensure that shielded cables have been used to route the signal to the input of the PVDJ 112P or 115P. If
speaker cables with 1/4" plugs are used as an input cables instead of shielded cables, it will be prone to
hum or buzz.
Hum may be ground loop related. Try lifting the ground connection at the speaker end of the signal cable if
it is a balanced signal cable. Check any input changes carefully by first turning down the volume control,
plugging and unplugging cables, or lifting the shield ground at the speaker end.
Check to make sure light dimmers are not on the same circuit as the PVDJ 112P or 115P, the mixer or any
source devices. If light dimmers are used, then it may be necessary to turn them full ON or full OFF to
eliminate or reduce hum. This is a typical AC wiring/light dimmer interference problem, and not a design
flaw of the PVDJ 112P or 115P. The third wire (ground plug) on the AC plug should NEVER be removed or
broken off.
DDiissttoorrtteedd oorr FFuuzzzzyy SSoouunndd
First, ensure the mixer (signal source) is not clipping or being overdriven. Make sure the volume control/s
(7) and (9) on the PVDJ 112P or 115P have not been set too low.
Check that the input plugs are fully seated in the input jacks (5) and (8) on the rear panel of the PVDJ 112P
or 115P. Ensure that the proper MIC/LINE PAD setting is being used (6) for line-level signals, or that a
power amp has not been plugged into one of the input jacks of the PVDJ 112P or 115P.
If an extension cord is being used to provide the AC power to the unit, ensure that it is of sufficient current
capacity and that it is not also being used to supply power to any other device.
The PVDJ 112P and 115P have built-in EQ to extend and smooth the natural response of the speakers in the
system. Bass boost and HF EQ have been applied and the system has a nominally flat response, so it
should require little, if any, additional EQ. If excessive additional bass boost or HF boost have been added
externally to the PVDJ 112P or 115P, it could cause premature overload at high SPL. Reduce the amount of
any external (mixer, rack) EQ and see if that clears up the distortion.
Finally, realize that even though the PVDJ 112P and 115P are powerful and high output units, they do
ultimately have limits, and it may need additional powered units (or a subwoofer) to provide enough
sound output or coverage. In this case, try turning the mixer levels down a little to see if that clears things
up.
If, after checking all the things listed to check and anything else you can think of to check safely, and the
system still exhibits problems, carefully note all conditions and check with your PVDJ dealer for advice.
CCaarree aanndd MMaaiinntteennaannccee
Your 112P or 115P is a sturdy and durable product and will provide years of reliable use if properly cared
10
for. Use common sense and read the safety warnings to avoid hazardous operating conditions.
The unit must be disconnected from the AC power source before any work is done on it. Refer all servicing
to qualified service personnel.
20 50 100 200 500 1k 2k 5k 10k 20k
Frequency (Hz)
60
70
80
90
100
110
dB SPL (re 20 Pa)
Amplitude Response (1m On-Axis)
FFRREEQQUUEENNCCYY RREESSPPOONNSSEE CCUURRVVEESS
Amplitude Response (1m On-Axis)
110
100
90
80
dB SPL (re 20 Pa)
70
60
20 50 100 200 500 1k 2k 5k 10k 20k
115P
Frequency (Hz)
112P
PVDJ LIMITED WARRANTY
Effective Date: July 1, 2003
WWhhaatt TThhiiss WWaarrrraannttyy CCoovveerrss
Your PVDJ Warranty covers defects in material and workmanship in PVDJ products purchased and serviced in the U.S.A. and Canada.
WWhhaatt TThhiiss WWaarrrraannttyy DDooeess NNoott CCoovveerr
The Warranty does not cover: (1) damage caused by accident, misuse, abuse, improper installation or operation, rental, product modification or neglect; (2)
damage occurring during shipment; (3) damage caused by repair or service performed by persons not authorized by Pvdj; (4) products on which the serial
number has been altered, defaced or removed; (5) products not purchased from an Authorized PVDJ Dealer.
WWhhoo TThhiiss WWaarrrraannttyy PPrrootteeccttss
This Warranty protects only the original retail purchaser of the product.
HHooww LLoonngg TThhiiss WWaarrrraannttyy LLaassttss
The Warranty begins on the date of purchase by the original retail purchaser. The duration of the Warranty is as follows:
Product Category Duration
Power Amplifiers 2 years *(+ 3 years)
Pre-Amplifiers, Mixers, Electronic Crossovers and Equalizers 2 years *(+ 1 year)
Enclosures 3 years *(+ 2 years)
Digital Effect Devices and Keyboard and MIDI Controllers 1 year *(+ 1 year)
Microphones 2 years
Speaker Components (incl. speakers, baskets, drivers,
diaphragm replacement kits and passive crossovers)
and all Accessories 1 year
Tubes and Meters 90 days
[*Denotes additional warranty period applicable if optional Warranty Registration Card is completed and returned to PVDJ by original retail purchaser within 90 days of purchase.]
WWhhaatt PPVVDDJJ WWiillll DDoo
We will repair or replace (at PVDJ's discretion) products covered by warranty at no charge for labor or materials. If the product or component must be shipped
to PVDJ for warranty service, the consumer must pay initial shipping charges. If the repairs are covered by warranty, PVDJ will pay the return shipping charges.
HHooww TToo GGeett WWaarrrraannttyy SSeerrvviiccee
((11))
Take the defective item and your sales receipt or other proof of date of purchase to your Authorized PVDJ Dealer or Authorized PVDJ Service Center.
OR
((22))
Ship the defective item, prepaid, to PVDJ, International Service Center, 412 Highway 11 & 80 East, Meridian, MS 39301 or PVDJ Canada Ltd., 95 Shields
Court, Markham, Ontario, Canada L3R 9T5. Include a detailed description of the problem, together with a copy of your sales receipt or other proof of date of
purchase as evidence of warranty coverage. Also provide a complete return address.
LLiimmiittaattiioonn ooff IImmpplliieedd WWaarrrraannttiieess
ANY IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE
LENGTH OF THIS WARRANTY.
Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
EExxcclluussiioonnss ooff DDaammaaggeess
PVDJ'S LIABILITY FOR ANY DEFECTIVE PRODUCT IS LIMITED TO THE REPAIR OR REPLACEMENT OF THE PRODUCT, AT PVDJ'S OPTION. IF WE ELECT TO REPLACE
THE PRODUCT, THE REPLACEMENT MAY BE A RECONDITIONED UNIT. PVDJ SHALL NOT BE LIABLE FOR DAMAGES BASED ON INCONVENIENCE, LOSS OF USE,
LOST PROFITS, LOST SAVINGS, DAMAGE TO ANY OTHER EQUIPMENT OR OTHER ITEMS AT THE SITE OF USE, OR ANY OTHER DAMAGES WHETHER INCIDENTAL,
CONSEQUENTIAL OR OTHERWISE, EVEN IF PVDJ HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
If you have any questions about this warranty or service received or if you need assistance in locating an Authorized Service Center, please contact the PVDJ
International Service Center at (601) 483-5365 / PVDJ Canada Ltd. at (905) 475-2578.
Features and specifications subject to change without notice.
Features and specifications subject to change without notice.
PVDJ a division of Peavey Electronics Corporation • 711 A Street • Meridian • MS • 39301
(601) 483-5365 • FAX (601) 486-1278 • www.pvdj.com
©2004 80307138
Loading...