Page 1
USER GUIDE
PRO SERIES Drinking Water Systems
Installation & operation manual
for Drinking Water Systems
PRO Series
For correct operation & installation it is
essential to observe these instructions.
Page 2
USER GUIDE
PRO SERIES Drinking Water Systems
PURETEC CUSTOMER SERVICE
Thank you for purchasing a Puretec drinking water system. Your system is a proven performer
manufactured from only quality materials and components and will give years of ‘spring fresh’
water free of impurities if maintained properly.
Caution: Do not use with water that is microbiologically unsafe or with water of unknown
quality without adequate disinfection before or after the system.
The system is designed for metropolitan supply water but can be used in other situations. For
other types of water supply please contact your local Puretec stockist
or call our Puretec Customer Service Helpline.
The Puretec filter systems cartridges need replacing regularly to maintain optimum performance.
This is a simple procedure when following instructions. For cartridge replacements contact your
nearest Puretec stockist.
Puretec Customer Service Helpline 1300 190 190
OPERATION
Puretec systems are designed to run economically for many years and this is dependant on the
initial installation and periodical maintenance.
Flush systems for 10 minutes after any period of non-use more than 2 days. For a period of nonuse of 2 weeks or more, it may be necessary to replace cartridges.
CARTRIDGE REPLACEMENT
You can obtain replacement cartridges from your local Puretec dealer and to maintain
performance and warranty use genuine Puretec replacements.
Replacement Cartridge Guide
System Model No. Replacement Cartridge Model No.
PRO90 PX051, CB951, RET1812-24
PRO130 PX051, CB951, RET1812-36
PRO270 PX051, CB951, RET1812-60
Other cartridges are available to suit a range of requirements upon request.
PRO SERIES Drinking Water Systems
2
Copyright © Fluid Products Pty Ltd 2012
Page 3
USER GUIDE
PRO SERIES Drinking Water Systems
CARTRIDGE INSTALLATION/CHANGEOUT
PRO SERIES
To change the filter cartridges adhere to the following procedure.
1. Close Ballvalve to prevent water flow
2. Unscrew Filter Housing using the spanner wrench and discard cartridges. When removing
housings place a container underneath to catch any spillage. Membrane housing cap can be
unscrewed by hand.
3. Cleanse the inside of the housing using Puretec S500 Sanitiser. Check O-Ring and lubricate
with food grade silicone lubricant or similar. Replace O-Ring if kinked or damaged.
4. Install new cartridges and replace housing screwing them up HAND TIGHT ONLY. PX051 filter is
on the inlet side and CB951 on the outlet side.
5. Restore water supply & check for leaks, rectifying them, if any, before leaving the unit.
After installing cartridges flush unit for 5 - 10 minutes.
INSTALLATION
INSTALLATION REQUIREMENTS
1. Supply pressure: 300 - 600kPa.
2. Supply temperature: 3°- 30°C.
Copyright © Fluid Products Pty Ltd 2012
User Guide
3
Page 4
USER GUIDE
PRO SERIES Drinking Water Systems
INSTALLATION PROCEDURE - See Figure 1
1. The unit comes with a Tap Adapter on the inlet side, identified by GREEN hose, which will
screw onto a standard tap without the need of thread seal tape. Make sure it is firmly screwed
to provide a seal on the rubber gasket (hand tighten only).
2. To gain access to the mounting screw holes on the mounting bracket, simply unclip the
R.O. housing from the clip attached to the main mounting bracket. This will reveal the wall
mounting screw holes to enable the mounting of the system to the wall, cupboard etc.
3. Purified water (BLUE hose), and waster water (BLACK hose) lines do not come with any
attachments. Pure water should be directed to a suitable container without any back pressure
or valving occurring in the line. The drain line, or waste water may be directed to the outside
garden, or if installed inside, to a washing machine, to conserve water. If inconvenient it may
be directed to any drainage system.
4. When the unit is in place and the water lines are installed, the unit should be run for four (4)
hours before the purified water is used, on initial start up. The unit cannot be stored for more
than two weeks without use, or damaged to the membrane may occur. Please enquire if this is
the case.
For a period of non-use greater than 2 days, flush for 10 min before use. For non-use greater
than 2 weeks, the cartridges may need replacing.
5. The Sediment and Chemical Removal Filters should be replaced every six (6) months. The
membrane should be replaced when water quality deteriorates or every 18-24 months,
depending on incomming water quality. A Puretec TDS meter (PTE10) can determine quality
for you at the push of a button.
For best performance use only genuine Puretec replacement cartridges and cartridges that are
suitable for this appliance.
PRO SERIES Drinking Water Systems
4
Copyright © Fluid Products Pty Ltd 2012
Page 5
USER GUIDE
PRO SERIES Drinking Water Systems
FIGURE 1.
6
1
2A
3
4
5
2A
5
4
END VIEW OF
MEMBRANE HOUSING
SEDIMENT REMOVAL CHEMICAL REMOVAL
2
9 8
7
No. DESCRIPTION
1 Tap Adaptor
2, 2A Tube Adaptor
3 Inlet Water - Green flexible tubing
4 Waste Water Outlet - Black flexible tubing
5 Pure Water Outlet - Blue flexible tubing
6 Membrane Housing
2
Copyright © Fluid Products Pty Ltd 2012
7 Mounting Bracket
8 Chemical Filter Housing
9 Sediment Filter Housing
User Guide
5
Page 6
USER GUIDE
PRO SERIES Drinking Water Systems
FIGURE 2.
HOW TO USE QUICK CONNECT FITTINGS
1. Cut the tube square and push in
to the tube stop. For metal tube
remove burrs and chamfer tube
end to prevent O-Ring seal being
damaged.
3. Tube is secured in position.
2. Fitting grips before it seals. Ensure
tube is pushed in to tube stop.
DISCONNECTION PROCEDURE
4. Push collet against body and
slide tube out of fitting.
PERFORMANCE DATA
Important Notice: Read this data sheet and compare the capabilities to your actual water
treatment needs before purchasing.
Manufacturer
Fluid Products
PO Box 64, Melrose Park
SA 5039 Australia
Phone: 1300 190 190
Seller
Name
Address
Phone:
Product: Drinking Water Filter
Model: PRO SERIES
PRO SERIES Drinking Water Systems
6
Copyright © Fluid Products Pty Ltd 2012
Page 7
USER GUIDE
PRO SERIES Drinking Water Systems
USE GUIDELINES
• Minimumoperatingpressure300kPa.
• Maximumoperatingpressure600kPa.
• Donotallowexposuretotemperaturesbelow4°C.
• Maximumoperatingtemperature38°C.
• Nominalowrate4LPM.
• Thissystemmustbeinstalledaccordingtolocalplumbingcodesonthecoldwaterline.
• ReplacementCartridges:SeeCartridgeInstallation,page2.
• Thissystemrequiresregularreplacementoftheltercartridgetomaintainproperoperation.
Varying chlorine, sediment, or organic substance levels may aect replacement frequency.
• Besuretochangetheltercartridgesatleastevery8,000litresor6monthswhicheveroccurs
first; or whenever you detect a change in taste, odour, or decrease in flow. 8,000 litres is
approximately equal to using 20 litres daily for one year.
Caution: Do not use with water that is microbiologically unsafe or of unknown quality without
adequate disinfection before or after the system.
SUBSTANCE REDUCTION
The Water Filter models listed above have been tested and certified under AS/NZS 3497 and AS/
NZS 4348 for reduction of chlorine, odour, particles, taste and turbidity. The performance of this
product has been verified and substantiated as the test data summarised below indicates. The
Substances may not be in your water.
Class Pass Comment
Particular Reduction
Taste, odour, chlorine reduction
Cryptosporidium & giardia cyst removal
Copyright © Fluid Products Pty Ltd 2012
III YES 75% or more
IV YES 75% or more
IIc
YES 99.9% or more
User Guide
7
Page 8
USER GUIDE
PRO SERIES Drinking Water Systems
NOTES
FPS designs, manufactures and supports Puretec water care products, the name you can trust for
viable and proven water solutions. All pictures and information are supplied as a guide only.
The complete range of Puretec products are developed, refined and made to meet and exceed stringent
specifications for the worldwide market.
Important Note: Sales of products are subject to our Terms & Conditions which are available upon
request. All specifications, prices and photos are a guide only and are subject to change without
notice. Please ring to confirm details. Do not use products with microbiological unsafe water without
adequate disinfection. Where water pressure exceeds maximum pressure specifications, a pressure
limiting valve must be fitted. Maximum flow depends on cartridge, vessel, pressure, impurities etc.
WARRANTY
WARRANTY: Any claim under this warranty must be made within 36 MONTHS of the date of purchase
of the product. This product is warrantied to be free of defect of material and workmanship for 36
months from date of purchase. To make a claim under the warranty, take the product and proof of
purchase to place where you purchased the product, and they will lodge a Warranty Request with
Puretec.
Puretec will pay your reasonable, direct expenses of claiming under this warranty. You may submit
details and proof of your expense claim to place of purchase for consideration.
This warranty is given by Puretec, ABN 66 474 243 571, 14-16 Bailey Street, St Marys SA 5064,
telephone no. 1300 190 190 and email at sales@puretec.com.au.
This warranty is provided in addition to other rights and remedies you have under law: Our goods
come with guarantees which cannot be excluded under the Australian Consumer Law. You are entitled
to replacement or refund for a major failure and to compensation for other reasonably foreseeable
loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of
acceptable quality and the failure does not amount to a major failure.
The warranty only applies if the product was used and/or installed in accordance with the user guide
and/or installation instructions. This warranty is given in lieu of all other express or implied warranties
and manufacturer shall in no circumstance be held liable for damages consequential or otherwise or
delays caused or faulty manufacturing except as excluded by law.
Applicable to all above, is that the Warranties need to be approved by Puretec to ensure product
was not incorrectly used, installed or claimed. False and incorrect claims will be pursued at Puretec’s
discretion, including chargeable inspection and labour costs incurred.
Customer Service Helpline 1300 190 190
Email sales@puretec.com.au
Web www.puretec.com.au
Copyright © Fluid Products Pty Ltd 2012
Loading...