Pure Reliability PR-3030 Product Manual

THEATRE WASH

PR-3030

This product manual contains important information about the safe installation and
use of this projector. Please read and follow these instructions carefully and keep this
manual in a safe place for future reference.

PR LIGHTING LTD.

Yingbin Road, Dashi Panyu, Guangzhou, 511430 China

http://www.pr-lighting.com

Theatre wash.

doc

INDEX

SECTION PAGE

SAFE USAGE OF THE PROJECTOR 3
INSTALLING THE PROJECTOR 4
FITTING THE LAMP 4
POWER CONNECTIONS 5
STAND-ALONE MODE 5
XLR CONNECTIONS AND TERMINATOR 5
CONTROLLER MODE – DMX 512 OPERATION 6
KEEPING THE PROJECTOR CLEAN 7
MAINTENANCE 8
TROUBLESHOOTING 8
TECHNICAL DATA 8
ELECTRICAL DIAGRAM 9

Please note that as part of our ongoing commitment to continuous product development, specifications are subject to change
without notice. Whilst every care is taken in the preparation of this manual we reserve the right to change specifications in the
course of product improvement. The publishers cannot be held responsible for the accuracy of the information herein, or any
consequence arising from them.
Every apparatus has been tested completely and packed properly by the manufacturer. Please make sure the packing and / or
the apparatus is in good condition before your installation and use. Should there be any damage caused by transportation,
consult your dealer and do not use the apparatus. But any damage caused by improper use will not be assumed by the
manufacturer and / or dealer.

THESE ITEMS ARE PACKED TOGETHER WITH THE PROJECTOR

Bracket (1 PCS)
Locking knob (with screw) ( 2 SET)
XLR plug (1 PCS)
XLR socket (1 PCS)
This manual (1 PCS)

Thank you for purchasing the product Theatre Wash, PR-3030.
This product manual contains important information about the safe installation and use of this

projector. Please read and follow these instructions carefully and keep this manual in a safe place for
future reference.

The Theatre Wash is an innovative projector with an elegant housing made from high quality
aluminiun-alloy with an epoxy paint finish. The Theatre Wash complies to CE norms and standards
and uses international DMX 512 protocol.

The Theatre Wash uses halogen 1200W lamp and features 2 colour-wheels with each wheel 5 dichroic
colours, and the colours can be mixed freely to produce wonderful and special colour effects. The lamp
brightness can be adjusted from 0 to 100%　by electronics, so it is suitable for use in TV station, disc,
singing and dancing stage, night club and so on.

The projecctor has a device of auto thermal cut-off for the unit operation in a safety condition.

ACCESSORIES

INTRODUCTION

2/10

Theatre wash.

doc

SAFE USAGE OF THE PROJECTOR

The following points are important for safety as well as for the smooth
installation and performance of the unit.

When unpacking and before disposing of the package check there is no transportation damage before
using the projector. Should there be any damage caused by transportation, consult your dealer and do
not use the apparatus. Keep the package well for your possible future transportation.

The projector is for indoor use only, IP 20. Use only in dry locations. Keep this device away from rain
and moisture, excessive heat, humidity and dust. Do not allow contact with water or any other fluids, or
metallic objects.

The projector is not designed or intended to be mounted directly on to inflammable surfaces.

The projector is only intended for installation, operation and maintenance by qualified personnel.
The projector must be installed in a location with adequate ventilation, at least 50cm from adjacent

surfaces. Be sure that all the cooling fans run normally and no ventilation slots are blocked.
Do not project the beam onto inflammable surfaces, minimum distance is 3m. 3m
Avoid direct exposure to the light from the lamp. The light is harmful to the eye.
Do not attempt to dismantle and / or modify the projector in any way.
Electrical connection must only be carried out by qualified personnel.
Before installation, ensure that the voltage and frequency of power supply match the power

requirements of the projector. Only use the lamp with the specified type and rating.
It is essential that each projector is correctly earthed and that electrical installation conforms to all

relevant standards.
Do not connect this device to any dimmer pack.
Make sure that the power-cord is never crimped or damaged by sharp edges. Never let the power-cord

come into contact with other cables. Only handle the power-cord by the plug. Never pull out the plug
by tugging the power-cord.

Keep the lamp clean. Do not touch the lamp glass with bare hand.
Switching the lamp on and off at short intervals will reduce the life of both the lamp and the projector.

Occasional breaks will prolong the life of both the lamp and the projector.
Never run the projector without a lamp.
There are no user serviceable parts inside the projector, do not open the housing and never operate

the projector with the covers removed.

Always disconnect from the mains, when the device is not in use or before cleaning it
or before attempting any maintenance work.

If you have any questions, don’t hesitate to consult your dealer or manufacturer.

3/10