User Manual
PT-E-HD10
To avoid EMI issue, complete STP Cat6 cable is strongly recommended!
User Manual
HDMI™ over Single Cat.X Extender with 2-way IR
Model PT-E-HD10
Designed in Germany
© 2016 PureLink GmbH All rights reserved.
User Manual
PT-E-HD10
Table of Contents
1. Safety and Notice .................................................................................. 2
2. Introduction ....................................................................................... 3
3. Features ........................................................................................... 3
4. Specication ....................................................................................... 4
5. Package Contents .................................................................................. 5
6. Connection Diagram ................................................................................ 5
7. Panel Description ................................................................................ 6-7
8. IR Pass-Through .................................................................................... 8
9. Hardware Installation .............................................................................. 9
10. EDID Learning ...................................................................................... 9
11. Notice ............................................................................................10
12. Warranty .........................................................................................11
1. Safety and Notice
The PT-E-HD10 HDMI™ over Single Cat.X Extender with 2-way IR has been tested for conformance to safety re-
gulations and requirements, and has been certied for international use. However, like all electronic equipments,
the PT-E-HD10 should be used with care. Please read and follow the safety instructions to protect yourself from
possible injury and to minimize the risk of damage to the unit.
• Follow all instructions and warnings marked on this unit.
• Do not attempt to service this unit yourself, except where explained in this manual.
• Provide proper ventilation and air circulation and do not use near water.
• Keep objects that might damage the device and assure that the placement of this unit is on a stable surface.
• Use only the power adapter and power cords and connection cables designed for this unit.
• Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device before cleaning.
2
User Manual
PT-E-HD10
2. Introduction
The PT-E-HD10 HDMI™ over Single Cat.X Extender with 2-way IR boosts up your video/audio transmission distance up to 50m (165ft) in HDTV 1080i format, and 40m (130ft) in HDTV 1080p format. PT-E-HD10 also supports
the most advanced 3D video format complaint with HDMI specication and therefore guarantees the highest 3D
video compatibility on the market. With only one cost eective Cat.X cable, users can readily extend HDTV sources
from DVD players, Blu-ray Disc player, PS3, PC, and any other kinds of sources compliant with TMDS to distant dis-
play monitors including HDMI or DVI enabled TV sets or LCD PC monitors. With the advanced design for the latest
HDMI technology, deep color video, DTS-HD or Dolby TrueHD audio, and HDCP supports and compatibility are all
further insured. This exibility makes HDCP compliant DVD players or PS3 transmit utmost high quality video and
audio with a greater distance at the minimal cost, when integrating several components apart. In addition, PT-EHD10 is also equipped with bi-directional IR pass-through path. This bonus feature allows users to boost IR control
distance up to 100m (330 ft) and makes IR control possible through only single Cat.X cable including HDMI signals.
The PT-E-HD10 includes two units: transmitting unit PT-E-HD10-TX and receiving unit PT-E-HD10-RX. The trans-
mitting unit is used to capture the input HDMI / DVI signals with IR control packets and carry the signals via one
cost eective Cat.X cable. The receiving unit is responsible for equalizing the transmitted HDMI signal and recon-
structing IR signals. The transmission distance between the sending and receiving units can be up to 50m (165ft)
at HD 720p or 1080i; or 40m (130ft) at Full HD 1080p. With an 8-level equalization rotary control on the receiving
unit, users can adjust the equalization strength to the received HDMI signals accordingly, and therefore optimize
the transmission distance between source and destination!
3. Features
• Support HDMI Deep Color & full 3D
• Extend the transmission up to 50m (165ft) from the HDMI source at HD 1080i or 720p 24-bit
• Extend the transmission up to 40m (130ft) from the HDMI source at Full HD 1080p 24-bit
• Extend the transmission up to 20m (65ft) from the HDMI source at Full HD 1080p 36-bit
• HDCP 1.1 compliant
• Minimize the cable skew by adjustable 8-level equalization control
• Pure unaltered uncompressed 7.1ch digital HDMI over Cat.X cable transmission
• DTS-HD and Dolby True HD high bit rate audio support
• Support full frequency IR signal from 20KHz to 60KHz
• Bi-directional IR path
• Allows cascading
• Wall mounting housing design for easy and robust installation
• Perfectly integrated with other HDMI over Cat.X series products
1. The claimed transmission distance here is subject to the grade of installed cable(s), source device and display.
2. For over CAT5/COAX transmission, the cable(s) has to be solid, not stranded. Any keystone jack along the
transmission path will kill the transmission performance signicantly!
3
User Manual
PT-E-HD10
4.Specications
Technical TX RX
Role of usage Transmitter [TX] Receiver [RX]
HDMI compliance HDMI Deep Color & full 3D
HDCP compliance Yes
Video bandwidth Single-link 225MHz [6.75Gbps]
Video support 480i / 480p / 720p / 1080i / 1080p60
HDMI over UTP Full HD: (1080p) ~40meter (130feet) (Cat.X)
HD: (720p/1080i) ~50meter (165feet) (Cat.X)
Audio support
Equalization
Input TMDS signal 1.2 Volts [peak-to-peak]
Surround sound [up to 7.1ch] or stereo digital audio
None 8 Level Digital Control
Input DDC signal 5 Volts [peak-to-peak, TTL]
ESD protection
Input 1x HDMI/1x 3.5mm 1x RJ-45/1x 3.5mm
Output 1x RJ-45/1x 3.5mm 1x HDMI/1x 3.5mm
HDMI connector Type A [19-pin female]
RJ-45 connector WE/SS 8P8C(Reverse Mode)
3.5mm connector IR receiver / IR blaster IR receiver / IR blaster
Rotary Switch None Signal level equalization
Dimensions 75 x 90 x 25mm (L x W x H)
Weight 480g
Power Supply 5V 2A DC
Power Consumption 1 Watt (max)
−Human body model — ±19kV (air-gap discharge) & ±12kV (contact discharge)
−Core chipset — ±8kV
Mechanical TX RX
Housing Metal enclosure
Dimensions
[L x D x H]
Model 75 x 91 x 27mm [2.9“ x 3.5“ x 1“] 75 x 91 x 27mm [2.9“ x 3.5“ x 1“]
Package 270 x 175 x 80mm [10.6" x 6.9" x 3.1"]
Carton 450 x 370 x 300mm [1'6" x 1'3" x 11.8"]
Weight
Fixedness Wall-mounting case with screws
Power supply 5V 2A DC
Power consumption 1 Watt (max)
Operation temperature 32˚ ~ 104˚F (0˚ to 40˚C)
Storage temperature -4˚ ~ 140˚F (-20˚ ~ 60˚C)
Relative humidity 20~90% RH (no condensation)
Model 239g [8.4oz] 239g [8.4oz]
Package 1000g [2.2 lbs]
4
User Manual
PT-E-HD10
5. Package Contents
• 1x PT-E-HD10 (TX & RX)
• 1x IR blaster
• 1x IR receiver
• 2x Power supply unit (+5VDC, 2A)
• 1x User Manual
6. Connection Diagram
5
User Manual
PT-E-HD10
7. Panel Description
Transmitting unit PT-E-HD10 TX
Front Panel
1. MODE:
0 - EDID Full-HD(1080p@60) - 24bit 2D video & 7.1ch audio
1 - EDID Full-HD(1080p@60) - 24bit 2D video & 2ch audio
2 - EDID Full-HD(1080p@60) - 36bit 2D video & 7.1ch audio
3 - EDID Full-HD(1080p@60) - 36bit 2D video & 2ch audio
4 - EDID HD(1080p@30)(1080i@60)(720p@60) - 24bit 2D video & 7.1ch audio
5 - EDID HD(1080p@30)(1080i@60)(720p@60) - 24bit 2D video & 2ch audio
6 - EDID Full-HD(1080p@60) - 36bit 3D video & 2ch audio
7 - EDID learning mode
2. HDMI IN: Connects to a HDMI source with a HDMI male-male cable
3. IR Receiver: Infrared 3.5mm socket for plugging in the extension cable of IR receiver
4. IR Blaster: Infrared 3.5mm socket for plugging in the extension cable of IR blaster
Rear Panel
5. +5V DC: Connect to 5V DC power supply unit.
6. HDMI SIGNAL OUT: Plug in a Cat.X cable and link to the RJ-45 port of the PT-E-HD10, receiving unit [RX]
6
User Manual
PT-E-HD10
7. Panel Description
Receiving unit PT-E-HD10 RX
Front Panel
7 8 9
7. HDMI OUT: Connect to a HDMI display with a HDMI male-male cable here.
8. SIGNAL LEVEL: Adjust the equalization control to the received HDMI signals. The HDMI signal level varies
from MAX (strongest) to MIN (weakest) for respective transmission length from longest possible range to
short distance. Please adjust the signal level from MIN to MAX and stop turning the rotary switch whenever
the audio/video is playing normally. Inappropriate signal level setting may cause overpowering issue that
would shorten the product life significantly!
9. IR Receiver: Infrared 3.5mm socket for plugging in the extension cable of IR receiver
10. IR Blaster: Infrared 3.5mm socket for plugging in the extension cable of IR blaster
10
Rear Panel
11 12
11. +5V DC: Connect to 5V DC power supply.
12. HDMI SIGNAL IN: Plug in a Cat.X cable and link to the RJ-45 port of the PT-E-HD10, transmitting unit [TX]
7
User Manual
PT-E-HD10
8. IR Pass-Through
IR Extenders
IR Blaster IR Receiver
IR Sockets
IR BLASTER:
plug in the IR blaster to emit all IR command signals received from the IR receiver from the other end to control
the devices corresponding to the IR signals.
IR RECEIVER:
plug in the IR receiver to receive all IR command signals from the IR remote controls of the corresponding devices.
CAUTION
Incorrect placement of IR Blaster and Receiver may result in the failure of the IR extenders. Please check
carefully before plugging in the IR extender to the respective IR sockets. Warranty will not cover the
damage.
DenitionofIREarphoneJack
IR Blaster IR Receiver
You can buy any IR extension cables in the market that are compatible to the definition of the IR
sockets for the matrix if necessary for replacement use. However, IR cables longer than 2m (6-ft)
i
may not work.
8
User Manual
PT-E-HD10
9. Hardware Installation
1. Connect a HDMI or DVI source (such as a Blu-ray Disc player) to the transmitting unit PT-E-HD10-TX
2. Connect a HDMI or DVI display (such as a LCD TV) to the receiving unit PT-E-HD10-RX.
3. Connect IR Blaster/Receiver to both TX and RX units.
4. Connect a Cat-5/5e/6 cable between the transmitting and receiving units.
5. Make sure this Cat-5/5e/6 cable is tightly connected and not loose.
6. Plug in 5V DC power supply unit to the power jack of the receiving unit PT-E-HD10-RX.
7. Plug in 5V DC power supply unit to the power jack of the transmitting unit PT-E-HD10-TX.
8. If you see ickering or blinking image on the display, please adjust the rotary control switch to improve the
cable skew. MAX stands for the strongest HDMI signal level for longest possible transmission length while MIN
stands for the weakest HDMI signal level for short transmission length. Please adjust the signal level from 7 to
0 and stop turning the rotary switch whenever the audio/video is playing normally. Inappropriate signal level
setting may cause overpowering issue that would shorten the product life signicantly!
10. EDID Learning
1. Turn on to the transmitting unit (TX) of PT-E-HD10.
2. Set the MODE rotary switch on the transmitting unit to 7.
3. Use a HDMI cable to connect the transmitting unit (TX) of PT-E-HD10 and the display. The LED on the RJ-45
port of the transmitting unit (TX) of PT-E-HD10 will dim and light again, which indicates the EDID learning
process is nished.
4. Unplug everything and resume the steps in [Installation].
9
User Manual
PT-E-HD10
11. Notice
1. When adjusting the signal level on the receiver unit, please dial the rotary control switch from MIN to MAX
and stop turning the rotary switch whenever the audio/video is playing normally. Inappropriate signal level
setting may cause overpowering issue that would shorten the product life signicantly!
2. If the DVI or HDMI device requires the EDID information, please use EDID Reader/Writer to retrieve and provide DVI or HDMI display EDID information.
3. All HDMI over CAT5 transmission distances are measured using Belden 1583A CAT5e 125MHz UTP cable and
ASTRODESIGN Video Signal Generator VG-859C.
4. The transmission length is largely aected by the type of Cat-5/5e/6 cables, the type of HDMI sources, and the
type of HDMI display. The testing result shows solid UTP cables (usually in the form of 300m [1,000ft] bulk
cables) can transmit a lot longer signals than stranded UTP cables (usually in the form of xed length patch
cords). Shielded STP cables are better suited than unshielded UTP cables. A solid UTP Cat-5e cable shows longer transmission range than stranded STP Cat-6 cable. For long extension applications, solid UTP/STP cables
are the only viable choice.
5. EIA/TIA-568-B termination (T568B) for Cat-5/5e/6 cables is recommended for better performance.
6. To reduce the interference among the unshielded twisted pairs of wires in Cat-5/5e/6 cable, one can use shielded STP cables to improve EMI problems, which is worsen in long transmission.
7. Because the quality of the CAT5/6 cables has the major eect on how long the transmission limit can achieve
and how good is the received picture quality, the actual transmission range is subject to one’s choice of Cat5/5e/6 cables. For desired resolutions greater than 1080i or 1280x1024, a Cat-6 cable is recommended.
8. If your HDMI display has multiple HDMI inputs, it is found that the rst HDMI input [HDMI input #1] generally
can produce better transmission performance among all HDMI inputs.
10
User Manual
PT-E-HD10
12. Limited Warranty
The SELLER warrants the PT-E-HD10 HDMI extender over single cat.X with bi-directional IR free from defects in the
material and workmanship for 1 year from the date of purchase from the SELLER or an authorized dealer. Should
this product fail to be in good working order within 1 year warranty period, The SELLER, at its option, repair or
replace the unit, provided that the unit has not been subjected to accident, disaster, abuse or any unauthorized
modications including static discharge and power surge. This warranty is oered by the SELLER for its BUYER
with direct transaction only. This warranty is void if the warranty seal on the metal housing is broken.
Unit that fails under conditions other than those covered will be repaired at the current price of parts and labor in
eect at the time of repair. Such repairs are warranted for 90 days from the day of reshipment to the BUYER. If the
unit is delivered by mail, customers agree to insure the unit or assume the risk of loss or damage in transit. Under
no circumstances will a unit be accepted without a return authorization number.
The warranty is in lieu of all other warranties expressed or implied, including without limitations, any other im-
plied warranty or tness or merchantability for any particular purpose, all of which are expressly disclaimed.
Proof of sale may be required in order to claim warranty. Customers outside Taiwan are responsible for shipping
charges to and from the SELLER. Cables and power adapters are limited to a 30 day warranty and must be free from
any markings, scratches, and neatly coiled.
The content of this manual has been carefully checked and is believed to be accurate. However, The SELLER assu-
mes no responsibility for any inaccuracies that may be contained in this manual. The SELLER will NOT be liable for
direct, indirect, incidental, special, or consequential damages resulting from any defect or omission in this manual,
even if advised of the possibility of such damages. Also, the technical information contained herein regarding the
PT-E-HD10 features and specications is subject to change without further notice.
11
User Manual
PT-E-HD10
Asking for Assistance
Technical Support:
Phone: +49 5971 800299 - 0
Fax: +49 5971 800299 - 99
Technical Support Hours:
8:30 AM to 5:00 PM Monday thru Thursday
8:30 AM to 4:00 PM Friday
Write To:
PureLink GmbH
Von-Liebig-Straße 10
D - 48432 Rheine
www.purelink.de
Loading...