2
FUSE & AC
This is a power socket with FUSE holder.
4
MIC inputs
Two groups of MIC inputs, e
accept a 1/4’’ type phone jack or a XLR
connection. Please use a low impedance
microphone and a properly wired. cable for
best results.
very input can
5
LINE inputs
Line inputs can accept line level signals via
a stereo RCA sockets and a XLR
connector, one MP3 player has been
linked to this line inputs inside.
6
CLIP
CLIPPING indicator
This LED will light when the output signal level exceeds the output capacity of the amplifier, reduce the
input signal level when this LED always lights.
7
MIC
Controls for adjusting MIC input level
8
LINE
Controls for adjusting LINE input level(include the signal levels from the built-in player)
9
MASTER
This control adjusts the final output level
10
LINE OUT
These sockets send out line signals, which fetched before frequency equalizer and master fader, used
for linking to another active speaker like this unit or for recording.
3
5-band Graphic equalizer
This is a 5-band graphic equalizer placed
in front of the master fader. It allows you to
adjust the overall output in equalization for
sound field compensation or prevent
feedback.
1
POWER Switch
Switch up to turn the unit on, and switch
down to turn it off. Make sure the MASTER
level control is down before you turn the
unit on.
11
USB port
This unit built in a music player, An U disk which loaded many songs easily can be a good quality line
signal source via this port.
12
Controls for built-in player
These keys allows you operate the built-in player.
13
Display for built-in player
This LCD display shows all kinds of status of the built-in player.
1. Read all safety and operating instructions before using
this product.
2. All safe ty and operating instructions should be kept for
future reference.
3. Read and understand all warnings lis ted on the
operating instructions.
4. Follow all operating instructions to operate this product.
5. This product should not be used near water , i.e. a bathtub,
sink, swimming pool, wet basement, etc.
6. Use only a dry cloth to clean this product.
7. Do not block any ventilation openings. The product should not
be placed fat against a wall or placed in a built-in enclosure
that will impede the fow of cooling air.
8. Do not install this product near any heat sources, such
as radiators, heat registers, stoves or any other apparatus
(including heat–producing amplifers) that produces heat.
9. Do not defeat the safety purpose of t he polarized or
grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding-type plug has two
blades and a third grounding prong. The wide blade or the
third prong are provided for your safety. If the provided plug
does not ft into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord being walked on or pinched,
particularly at plugs, convenience receptacles and the point
where they exit from the apparatus. Do not break the ground
pin of the power supply cord.
11. Only use attachments specifed by the manufacturer.
12. Use only with the car t, stand, tripod, bracket,
or table specifed by the manufacturer or
sold with the apparatus. When a cart is
used, use caution when moving cart/
apparatus combination to avoid injury
from tip-over.
13. Unplug this apparatus during lightning stor ms or when
unused for long periods of time.
14. Care should be taken so that objects do not fall and liquids
are not spilled into the unit through the ventilation ports or
any other openings.
15. Refer all servicing to a qualifed ser vice professional. Servic
ing is required when the apparatus does not operate normally
or has been damaged in any way, including damage to the
power cord or plug, damage due to liquids spilled or objects
dropped inside the unit, dropping the unit, or anything else
that interrupts normal use of the unit.
16. WARNING: To reduce the risk of fre or electric shock, do not
expose this apparatus to rain or moisture.
17. When a mains plug is used as the disconnect device, the
disconnect device shall remain readily operable.
Important Safety Instructions
Exposure to extremely high noise levels may cause
permanent hearing loss. Individuals vary considerably
to noise-induced hearing loss but most will lose some
hearing if exposed to intense noise for a suffcient
period of time.
DANGER
THIS SYMBOL IS INTENDED TO ALERT THE USER TO THE PRESENCE
OF NON-INSULATED “DANGEROUS VOLTAGE” WITHIN THE
PRODUCT’S ENCLOSURE THAT MAY BE OF SUFFICIENT MAGNITUDE
TO CONSTITUTE A RISK OF ELECTRIC SHOCK TO PERSONS
THIS SYMBOL IS INTENDED TO ALERT THE USER TO THE PRESENCE
OF IMPORTANT OPERATING AND MAINTENANCE (SERVICING)
INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE UNIT.
APPARATUS SHALL NOT BE EXPOSED TO DRIPPING OR SPLASHING
AND THAT NO OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES,
SHALL BE PLACED ON THE APPARATUS.
4
12
11
POWER
VOL+ VO L-
EQ
LINE OUT
MIC1 IN
MIC2 IN
LINE IN
L
R
USE ONLY WITH 250V FUSE
CAUTION:
FIRE, REPLACE FUSE WITH THE ASME
TYPE AND RATING. DO NOT EXPOSE
THIS EQUIPMENT TO RAIN OR MOISTURE.
HOUSEHOLD USE ONLY
TO REDUCE THE RISK OF
GRAPHIC EQUALIZER
+12
+6
0dB
-6
-12
MIC1
MIC2
LINE
MASTER
0 10
0 10
0 10
0 10
+12
+6
0dB
-6
-12
6K2K
750250
12K
3
6
7
8
9
FUSE:T2A 250 V
AC~:220V 50H z
285VA MAX
AVIS: Ne pas ouvr ir l'ap parei l!
Danger de déc harge é lectr ique!
CLIP
13
5
10
1
2