Pure Acoustics SUPERNOVA Series, Noble II-F, Noble II-C, Noble II-S, Supernova 1F Owner's Manual
...
Technical Specifications
SUPERNOVA
SUPERNOVA
SERIES
OWNER’S MANUAL
THE PURE SOUND OF LIFE
PURE ACOUSTICS®
Pure Acoustics,Inc.
18 F
uller Place • Brooklyn, NY 11215
C
ustomer Service: 718-788-4411
www.pure-acoustics.com
Design and specifications are subject to change without notice.
www.pure-acoustics.com
POWER HANDLING
FREQUENCY RESPONSE
SENSITIVITY (+/–3dB)
OHMS, NOMINAL/MIN.
DRIVER COMPLEMENT
WOOFER
TWEETER
CROSSOVER FREQUENCY
DIMENSIONS (H x W x D)
WEIGHT
FINISH
GRILLE
CARTON CONTAINS
Supernova 1F Supernova 5F Supernova 8F Supernova C Supernova S
60 W RMS,
100 W peak
50 Hz - 20 KHz
87 dB
8/4 ohms
2-way,2 DRAV RG
One 6.5˝ high-
efficiency cone,
25mm KSV voice coil,
Y30 ferrite magnet
1˝ black oil-cooled
silk diaphragm, with
neodymium magnet
2,800 Hz
8.46 x 15.75 x 12.2 ins.
17 lbs.
Black high-gloss front,
wood sides
Black
One pair of bookshelf
speakers in one carton
220 W RMS,
325 W peak
42 Hz - 20 KHz
92 dB
8/4 ohms
2-way,3 DRAV RG
Two 6.5˝ high-
efficiency cones,
35mm KSV voice coil,
Y30 ferrite magnet
1˝ black oil-cooled
silk diaphragm, with
neodymium magnet
2,500 Hz
32.75 x 8.46 x 12.5 ins.
32 lbs.
Black high-gloss front,
wood sides
Black
One speaker in
one carton
250 W RMS,
350 W peak
40 Hz - 20 KHz
92 dB
8/4 ohms
2-way,4 DRAV RG
Three 6.5˝ high-
efficiency cones,
35mm KSV voice coil,
Y30 ferrite magnet
1˝ black oil-cooled
silk diaphragm, with
neodymium magnet
3,200 Hz
42.5 x 8.46 x12.5 ins
39 lbs.
Black high-gloss front,
wood sides
Black
One speaker in
one c
ar
t
on
150 W RMS,
250 W peak
60 Hz - 20 KHz
89 dB
8/4 ohms
2-way,3 DRAV RG
Two 5.25˝ high-
efficiency cones,
20mm KSV voice coil,
Y30 ferrite magnet
1˝ black oil-cooled
silk diaphragm, with
neodymium magnet
3,800 Hz
6.5 x 18.11 x 8 ins.
11 lbs.
Black high-gloss front,
wood sides
B
lack
One speaker in
one c
ar
t
on
150 W RMS,
250 W peak
65 Hz - 20 KHz
89 dB
8/4 ohms
2-way,2 DRAV RG
One 5.25˝ high-
efficiency cone,
20mm KSV voice coil,
Y30 ferrite magnet
1˝ black oil-cooled
silk diaphragm, with
neodymium magnet
3,800 Hz
12.25 x 7 x 8 ins.
8 lbs.
Black high-gloss front,
wood sides
Black
One pair of bookshelf
speakers in one carton
INTRODUCTION
Thank you for purchasing Pure Acoustics’products, and welcome to the Pure Acoustics family
of satisfied customers! Pure Acoustics was established to fulfill the need for high quality
speakers of exceptional design at an affordable price. After years of research and development, and by manufacturing all parts ourselves – from the voice-coil to the uniquely-designed
crossover – Pure Acoustics is able to offer you speakers of superior value.
Each speaker component has been designed and engineered with first-rate materials to produce exceptional sound. Our speakers offer the best of it all – high-quality sound, hand-made
solid construction, and a remarkably stylish appearance. We welcome you to witness the
results. Our team’s dedication to quality, reliability and attractive design has created some of
the best-value speakers you can find today.
Unpacking
Carefully remove your new Pure Acoustics speakers from the box. Inspect the speakers for
transit damage. If you discover damage, please contact your dealer immediately. Save your
carton, it’s the best possible protection for your speakers should you ever need to move them.
Connecting Wires and Receiver
Reading this and your amplifier’s owner manual fully will help you to set up your speaker
properly and reward you with a fine listening experience.
WARNING for U.S.Customers – In some cases, Pure
Acoustics models may contain two pairs of binding post
wire terminals. Per Diagram A, it is important that U.S.
customers do not remove the jumper links which are
attached between the positive and negative terminals.
Removing these connectors, and/or wiring more than
one left and one right wire into your speaker will lower impedance and can damage your
equipment. If your speaker contains these terminals, only connect wires to top positive and
negative terminals,not to the bottom terminals. For further information, please contact 718788-4411 for technical support.
Make sure all equipment is turned off. When connecting the speakers, be certain to retain
the correct polarity. Most speaker wire is polarity coded either by color or texture.This means
that each conductor is labeled either (+) positive or (–) negative.In the back of your amplifier,
each channel is labeled (+) and (–) as well. You must ensure that you connect (+) to (+) and
(–) to (–).
Warning: If you connect the speaker wires out of phase,meaning (+) to (–) or (–) to
(+), this will dramatically
reduce bass response and
change the tonal characteristics of the speaker.
Also, if wires
are loose, it
can cause
crackling,
static types
of sounds, and/or
short circuit
your equipment.
Diagram A
Connect wires to top terminals only
Speaker Positioning
The diagram below shows 5.1,6.1, and 7.1 speaker system placement.
The front center-channel
speaker should be placed as
close to the TV as possible,
preferably directly above or
below the set. The front channel speakers should be placed
at least 6 feet apart (T V/monitor center) to create proper
stereo imaging. The 5.1 surround speakers should be
equally spaced to the side of
the listener. The rear-center
speaker should be positioned
directly behind the listening
area.The rear channel speakers
should be positioned behind
and slightly to the sides of the
viewer/listener. It may take
some experimentation with
different locations for the surround speakers to suit your
preference and your room.
Running Time
and Cleaning
The performance of the speakers may change during the initial use due to storage and
mechanical limitations. Please allow 15 hours of use for the temperature effect and mechanical parts to attain their intended design characteristics.
Make sure to turn all equipment off before cleaning. The cabinet only requires occasional
dusting. Please avoid touching the drive units.
Troubleshooting, Service, and Limited Warranty
Pure Acoustics products have been designed and manufactured to the highest quality standards. If you experience a problem, first try to determine if it is indeed a speaker issue.
Determine whether the problem exists in both speakers. If it does,the problem likely originates in some other component in the system. If the problem is in one speaker only, reverse
your speaker leads (left to right, right to left).If the problem moves to the other channel, your
pr
oblem is not in the speakers.
I
f y
ou ha
ve determined you have a speaker problem, please contact your dealer or Pure
Acoustics Customer Service at 718-788-4411. Warranty is only valid for the original owner
and is limited to the repair of the product for manufacturer defects, either in materials or
workmanship. Warranty does not apply to units that were subject to misuse, neglect,abuse,
alteration, or improper installation. Warranty does not cover damage due to fire,water, heat,
lightning,or any other cause beyond the control of Pure Acoustics. All warranty repairs must
b
e acc
ompanied b
y the or
iginal bill of sale
.
No other document is acceptable or required.
Front left & right
Center
Left surround
(5.1)
Rear left
(Add for 7.1)
Optional
subwoofer
right or
left side
Right surround
(5.1)
Rear Center
(Add for 6.1)
Rear right
(Add for 7.1)
Loading...