The AND-TFT-64PA-KIT is a compact full color TFT LCD
module, that is suitable for applications such as a car TV,
portable DCD, GPS, multimedia applications and other AV
equipment. This device consists of a twisted nematic (TN)
liquid crystal cell, that incorporates a TFT-array that has
960 x 234 pixels on a 6.4 inch diagonal screen, X and Y
drivers, an LSI controller, and a built-in CCFL backlight and
inverter (with optional board.)
Features
• 6.4 inch (16 cm) diagonal screen
• Compatible with NTSC & PAL system
• Accepts VGA Input (Analog RGB)
• High brightness CCFL backlight (300 Nits)
• Slim and compact
• Operating temperature range -10 to 60° C
Mechanical Characteristics
ItemSpecificationUnit
Screen Size6.4 inch (16 cm) diagonalinch
Surface TreatmentAnti-Glare + WV film–
Display
Format
320 (H) x 234 (V)dot
Active Area129.6 (H) x97.34 (V)mm
Dot Pitch0.135 (H) x 0.416 (V)mm
Pixel ConfigurationStripe–
• Storage temperature range -30 to 80° C
• 12V single power supply (with optional board)
• High brightness
Outline
Dimensions
156.3 typ. (W) x 119.8 (H)
x 14.3 typ (D)
mm
WeightTBD ± 10g
Absolute Maximum Rating
Absolute Maximum
ItemSymbolConditions
Rating
Unit
Min.Max.
Supply Voltage for Source Driver
Analog
Digital
Positive
Supply Voltage for Gate Driver
Analog input voltage (V
, V
R
Negative
, V
)V
G
B
Digital input signals–
Digital output signals–-0.5+5.5V
V
CC
V
DD
V
GH
V
GL
V
V
GH
GL
DD
HSY
, POLC, CSY, VSY, CLKC
PSI, COMPS, VIY
–-0.3+7.0
-0.3+7.0
–-0.3+45V
–-23+0.3V
+15+40V
–
-0.3+7.3V
-0.5+5.5V
Storage Temperature––-30+80°C
Operation Temperature
(defines that contrast, response time & other display
optical characteristics are Ta=+25.)
––-20+70°C
V
Product specifications contained herein may be changed without prior notice.
It is therefore advisable to contact Purdy Electronics before proceeding with the design of equipment incorporating this product.
* Note: Contrast Ratio is measured in optimum common electrode voltage.
CR>
Luminance when LCD is White
Luminance when LCD is Black
** 1. Topcon BM-7 (fast) luminance meter 2.0 field of view is used in the testing (after 20~30 minutes operation.)
2. Lamp Current: 6mA
3. Inverter model: TDK-347.
*** The uniformity of LCD is defined as:
U=
The Minimum Brightness of the 9 testing Points
The Maximum Brightness of the 9 testing Points
Luminance meter: BM-5A or MB-7 fast (TOPCON)
Measurement distance: 500mm +/- 50 mm
Ambient illumination: < 1 Lux
Measurement direction: Perpendicular to the surface of module.
The test pattern is white (Gray Level 63.)
1. Input/Output Connector
A) LCD Connector: 6200-20P (Molex)
FFC Up Connector
20 Pins
Pitch: 1.0 mm
B) Backlight Connector: JST BHR-03VS-1
Pin No: 3
Pitch: 4.0 mm
Pink: High Voltage
White: Low Voltage