INSTRUCTION MANUAL
INTRODUCTION
Thank you for choosing the PULSETEC Battery Discharger & Analyzer B-GEN 200. The B-GEN 200
is a powerful discharging device that allows the user to discharge a battery at up to 30 amps or 200
watts and also measures and compares the performance of batteries. B- GEN 200 allows for the precise
measurement of battery capacity and takes the guesswork out of choosing the best battery for your
application.
The B-GEN 200 is much more than a simple battery discharger or a batter y load tester. It will test virtually
any type or size of battery, any chemistry or number of cells, up to 35 volts.
The B-GEN 200 is ruggedly built and uses XT60 connector for batter y connection. It is small with a high
performance cooling system. Digital LED indicates battery voltage, discharge capacity and discharge
current.
#PC-022- 001
FE ATUR ES
• It displays real time battery voltage, discharged capacity and discharge current.
• It can test batter y capacity that helps select batteries with desired capacity.
• It saves time when user wishes to store their large capacity batteries.
• It helps activate the best performance of your batteries for competition.
FE ATUR ES
1- BATTERY CONNECTION 2- POWER ON
Press the Dial once to power
ON the discharger, the LED
(V/mAh) will blink with beep
sound.
Heat Sink
XT-60 Batter y Port
DATA Link
SPECIFICATIONS
Accepted Voltage Range : ...... 5,40 - 35,00V
Low Voltage Alert : ...................<5,2V
High Voltage Alert : ................... >35V
Max Discharge Power : ................200W
Discharge Current range : ..... 0,01A - 30,00A
Current consumption in Sleep Mode ...<100uA
Standby Current : .................. <35mA
Current Display Accuracy: . 0.01-10.00A ±60mA
10.00-30.00A ±2%
Cooling Fan
ROTAR Y D IA L
for Setting Cut-off Voltage
Discharging Current
Start/Stop Button
Current Display (A)
Batter y Voltage / Capacity
Display (mAh)
Voltage Display Accuracy: .....5.4-10V ±60mV
10-20V ±120mV
20-35V ±160mV
Capacity Display Accuracy : .............±3%
Dimension : ................ 136x105x96mm
Weight : ............................ 858g
3- SELECT CUT-OFF VOLTAGE AND DISCHARGE CURRENT
The LED(V/mAh) shows the current battery voltage.
By rotating the Dial button to change cut-of f voltage, then press Dial button once to conrm.
Use the Dial button to modify the discharge current
4- START DISCHARGING PROCESS
Press and hold Dial button for 2 seconds, the discharger will start
with beep sound.
During the discharging process, the digital LED(V/mAh) will alternate
the display of battery voltage and discharging capacity.
5- STOP DISCHARGING PROCESS
During the discharging process, Press the dial once to stop the
discharging process, the digital LED(A) shows “Stop”.
5- PROCESS FINISHED
When the discharging process has nished, the discharger will beep
5 times, and the LED(V/mAh) will show battery voltage and discharge
capacity respectively.
1 2
Battery
Typ e
LiPo
LiHV
NiMH
No. of
Cell
2S 6.0 8.40 23.80 30.00
3S 9.0 12.6 0 15.87 22.20
4S 12.0 16.80 11.9 0 16.60
5S 15.0 21.0 0 9.52 13.30
6S 18.0 25.20 7. 9 3 11.10
7S 21.0 29.40 6.80 9.52
8S 24.0 33.60 5.95 8.33
2S 6.2 8.70 22.98 30.00
3S 9.3 13.0 5 15.3 2 21.50
4S 12.4 17.40 11.4 9 16.1 2
5S 15.5 21.75 9.1 9 12.9 0
6S 18.6 26.1 0 7.6 6 10.75
7S 21.7 30.45 6.56 9.21
8S 24.8 34.80 5 .74 8.06
6S 5.4 9.00 22.22 30.00
7S 6.3 10.50 19.04 30.00
8S 7. 2 12.0 0 16.66 27. 7 7
9S 8.1 13.5 0 14.81 24.69
10S 9.0 15 .00 13.33 22.22
11S 9.9 16.5 0 12.12 20.20
12S 10.8 18.00 11.11 18. 51
13S 11.7 19.50 10.25 17.0 9
14S 12.6 21.0 0 9.52 15. 87
15S 13.5 22.50 8.88 14.81
16S 14.4 24.00 8.33 13.8 8
17S 15.3 25.50 7. 84 13.07
18S 16.2 2 7. 0 0 7.4 0 12.34
19S 1 7.1 28.50 7. 0 1 11.6 9
20S 18.0 30.00 6.66 11.11
Min. Cut-Of f
Voltage
Voltage
Min. Discharge Current (A)
Discharging power: 200W
ERROR MESSAGE
When there is an error, digital LED will display the error code :
Max. Discharge Current (A)
Discharging power: 200W
PC SOFTWARE
• PC software supplied with the B-GEN 200 is easy to use, intuitive.
• There are two discharge mode: Constant Power and Constant
Current.
• The software can automatic sensing of battery cell count and
recommends a minimum safe discharge voltage.
• Discharge tests may be viewed in Amp Hours, Watt Hours or
Minutes.
• Results can be graphed as Voltage vs. Amp hours, Watt hours,
Minutes.
SAFETY NOTE
• Never discharge a battery below its recommended cut-off voltage. Over-discharge may damage
battery and cause FIRE or EXPLOSION.
• Never discharge a battery at a higher discharge rate than it is designed for.
• Never leave the discharger unattended when it is connected to battery. If any malfunction is found,
TERMINATE THE PROCESS AT ONCE.
• Place the discharger and battery on a non-flammable surface, and keep away from inflammables.
• Never discharge swollen, leaky, or damaged batteries.
• Batteries shall be discharged within a room temperature range of 10-40°C.
• Disconnect the battery and discharger once discharging has nished.
• Recharge batteries immediately with an appropriate battery charger after discharge process is
completed. Some battery types do not like to remain discharged for extended periods of time.
WARRANTY AND SERVICE
We guarantee this product to be free of manufacturing and assembly defects for a period of 12 or 24 months from the
time of purchase. The warranty only applies to material or operational defects, which are present at the time of purchase.
During that period, we will repair or replace free of service charge for products deemed defective due to those causes.
You will be required to produce proof of purchase (invoice or receipt). This warrant y is not valid for any damage or
subsequent damage arising as a result of misuse, modication or as a result of failure to observe the procedures outlined
in this manual.
DURATION OF VALIDITY
The claim period is 24 months from the date of purchase of the product by the consumer from a dealer in the European
Community (EC) counted from the date of purchase. The claim period is 12 months from the date of purchase of the
product by the consumer from a dealer outside the European Community (EC) counted from the date of purchase. If a
defect ar ises after the end of the claim period, or if evidence or documents required acc ording to this declaration in order
to make the claim valid are not presented until af ter this period, then the consumer forfeits any rights or claims from this
declaration. The guarantee period is not prolonged by the granting of any claims within the framework of this warranty,
especially in the c ase of repair or replacement. The guarantee period also does not restart in such cases.
WARRANTY EXPIRATION
If we do not acknowledge the validity of a claim based on this declaration within the c laim period, all claims based on this
declaration will expire after six months from the time of registering the claim; however this cannot occur prior to the end
of the claim period.
Over-temperature protection.
Input voltage is too high. This discharger accepts batter y voltage from 5.4 to 35V, if
voltage higher than 35V, it will stop working and show error message.
Input voltage is too low. This discharger accepts battery voltage from 5.4 to 35V, if voltage
lower than 5.4V, it will stop working and show error message.
3 4
Download
English Manual
Téléchargez le Manuel
en Français
Download
Deutsche Anleitung
TCRP INTERNATIONAL LLC Ltd • 21B Moskovska Street. Floor 3 • 1000 Soa - Bulgaria • info@tcrp-intl.com - www.pulsetec.eu
Loading...