Pulse Performance Products REVSTER 200 Owner's Manual

NOTE: CAN BE USED AS A KICK SCOOTER OR, BY PRESSING THE THUMB

THROTTLE, ELECTRIC POWER WILL ENGAGE THE MOTOR FOR ADDED
POWER AND ACCELERATION. YOUR RIDE TIME WILL VARY GREATLY
DEPENDING ON THE AMOUNT OF POWER-ASSISTED RIDING PERFORMED.

ELECTRIC SCOOTER
OWNER’S MANUAL

FOR USE WITH THE FOLLOWING PULSE PERFORMANCE PRODUCTS™ SCOOTERS

•

REVSTER 200

DO NOT RETURN TO STORE! QUESTIONS OR COMMENTS?
CALL (866)-434-6067

04.24.19

Table of Contents

Safety and Warnings 2-3
Before You Start 4
Assembly 5-6
Hardware Maintenance 7
Before You Ride 7
Repair and Maintenance 8-10
Troubleshooting 11
Scooter Components 12
Warranty 13

Safety and Warnings

WARNING:

of the manufacturer. Scooter can and is intended to move and it is therefore
that no amount of care, instruction or expertise can eliminate. If such a thing does occur you can become seriously injured or die, even when
using safety equipment and other safety precautions. RIDE AT YOUR OWN RISK AND ALWAYS USE COMMON SENSE. To reduce the risk of

injury, ADULT SUPERVISION IS REQUIRED.

This manual contains many warnings and cautions concerning the consequences of failing to inspect, maintain or properly use your electric
scooter. Since any incident can result in serious injury or even death, we do not repeat the warning of possible serious injury or death each
time such a possibility is mentioned in this manual.

Riding an electric scooter can be a dangerous activity.

Certain conditions may cause components to fail without fault

possible to lose control, fall off

and/or get into dangerous situations

APPROPRIATE RIDING ATTIRE

Always wear proper protective equipment such as:

• Approved safety helmet. (Helmet may be legally required by local law or regulation in your area.)

• Elbow pads and knees pads

• Long sleeved shirt, long pants

• Gloves

• Lace up, closed toe shoes with rubber soles, never ride barefooted or in sandals, and ensure that shoelaces are tied and kept out of the way
of the wheels and drive system.

RIDER USE AND PARENTAL SUPERVISION

RIDER MUST NOT EXCEED THE WEIGHT LIMIT OF 120 pounds (54kgs). Rider weight does not always mean a person’s size is appropriate

To reduce the risk of injury, ADULT SUPERVISION IS REQUIRED.

This manual contains extremely important safety information. It is your responsibility to completely review this information and make sure that
all riders understand all warnings, cautions, instructions and safety topics and assure that all riders are able to safely and responsibly use this
scooter. Pulse Performance Products™ advises that you periodically review and reinforce all information in this manual with all riders, and
that you inspect and maintain your scooter to insure their safety.

to 12 yrs.

decision to allow their child to use the scooter should be based on the child’s maturity, skill level and their ability to follow rules.

Never use in roadways, near motor vehicles, on or near steep inclines or steps, swimming pools or other bodies of water.

Do not touch the motor or brakes on the scooter when in use or directly after use as these parts can become extremely hot.

Keep this scooter away from small children and remember that it is intended for use only by persons who are, at a minimum, completely
competent and comfortable while operating this product.

RIDING PRACTICES AND CONDITIONS

Check and obey any local laws or regulations which may affect the locations where the electric scooter may be used.

Always ride defensively. Watch out for obstacles that could catch your wheel or force you to turn suddenly or lose control. Be careful to avoid
pedestrians, other wheeled products (such as skaters, skateboards, scooters, bikes, etc.), children or animals who may enter your path.
Always respect the rights and property of others.

Do not depress the thumb button on the hand grip unless you are on the

Do not attempt or perform racing, stunt riding, tricks, or other manuevers, which may cause loss of conrtrol, or may cause uncontrolled operator
actions or reactions. This product is not made to withstand abuse from jumping, curb grinding or other dangerous riding activities.

2

Questions or concerns? Visit our website at www.pulsescooters.com for replacement parts and technical support, or call [phone].

scooter and in a safe, outdoor environment that is suitable for riding.

.

Safety and Warnings

WARNING:

FAILURE TO HEED TO THE WARNINGS LISTED BELOW INCREASES RISK OF POTENTIAL SERIOUS INJURY. USE THE
APPROPRIATE CAUTION WHEN RIDING AND ALWAYS WEAR PROTECTIVE GEAR.

Maintain a hold with both hands on the handlebars at all times.

Never allow more than one person at a time to ride the scooter.

Never use on roadways, near motor vehicles, on or near steep inclines or steps, swimming pools or other bodies of water.

Do not allow your hands, feet, hair, body parts, clothing or similar articles to come in contact with moving parts, wheels, or drivetrain, while the
motor is running.

Never ride while using a cell phone or wearing headphones.

Never hitch on to or with another vehicle or pull anyone or anything.

Never immerse the scooter in water; electrical and drive components could be damaged by water or create other possible unsafe conditions.

ater, mud, ice,
bumpy, uneven, slick, or rough surfaces could impair traction and contribute to possible loss of control. Avoid excessive speeds that can occur
from downhill rides which could cause loss of control.

Do not ride at night or in areas of limited visibility.

originally supplied by the manufacturer are in proper place and in serviceable condition. That any and all axle guards, chain guards, or other
covers or guards supplied by the manufacturer are in place and in serviceable condition.

Ensure that the area that the unit is to be operated in is safe and suitable for safe operating.

Ensure that all safety labels are in place and understood by the operator.

Persons with the following conditions shall be cautioned not to operate: Those with heart conditions, pregnant women, persons with head,
back, or neck ailments, or prior surgeries to those areas of the body. Persons with any mental or physical conditions that may make them
susceptible to injury or impair their physical dexterity or mental capabilities to recognize, understand, and perform all of the safety instructions
and to be able to assume the hazards inherent in unit use.

Maximum operating speed is 8 MPH (13 KM/H).

Before each ride the following checks will need to be performed to the scooter:

• Ensure that the brake system is functioning properly.

• Components shall be maintained and repaired in accordance with the manufacturers authorized replacement parts with installation
performed by dealers or other skilled individuals.

BATTERIES, FUSES, CIRCUIT BREAKERS & USING THE BATTERY CHARGER

The battery charger should be regularly examined for damage to the cord, plug, enclosure and other parts. In the event of such damage, if
any is found, the scooter should not be charged until the battery charger has been repaired or replaced.

Use only with the supplied, recommended battery charger.

Always use caution when charging.

The battery charger is not a toy and should be operated by an adult.

Disconnect the battery charger and unplug from scooter when not in use.

Do not exceed recommended charging time.

Always disconnect the battery charger from the scooter prior to wiping down and cleaning with any liquid.

Do not mix old and new batteries. Do not mix alkaline, standard (carbon-zinc), or rechargeable batteries.

Only use the batteries specified by the manufacturer.

RISK OF FIRE. Do not bypass fuse or circuit breaker. The circuit breaker on this scooter is not replaceable by the user - it is an integral part of
the controller. Replace the controller only with an identical part as specified by the manufacturer.

WARNING:

FAILURE TO HEED TO THE WARNINGS LISTED ABOVE INCREASES RISK OF POTENTIAL SERIOUS INJURY. USE THE
APPROPRIATE CAUTION WHEN RIDING AND ALWAYS WEAR PROTECTIVE GEAR.

3Questions or concerns? Visit our website at www.pulsescooters.com for replacement parts and technical support, or call [phone].

Before You Start

WARNING:

turned “OFF” before assembling the scooter.

Remove all packing and items from the display box. Make sure that the power switch is

Estimated Assembly Time

• Allow up to 25 minutes for assembly, not including initial charge time.

• Allow up to 12 hours for the initial charge (see page 6 for charging information).

thumb switch throttle

brake

NOTE: This scooter does not have a
manual reset button or fuse. It is
integrated into the controller and is
self-resetting.

battery charger
(included)

Required Tools

10 mm / 8 mm

wrench
(included)

two [2] 13 mm
wrenches
(not included)

5 mm hex wrench
(included)

second
5 mm hex wrench
(not included)

3 mm hex wrench
(not included)

charging port

phillips
screw driver
(not included)

WARNING:

may or may not be compatible with the design and will void the warranty.

4 Questions or concerns? Visit our website at www.pulsescooters.com for replacement parts and technical support, or call [phone].

DO NOT USE NON-PULSE PERFORMANCE PRODUCTS™ PRODUCTS WITH YOUR

Altering of the original components

Assembly

Handlebar Steer Tube Assembly

Tools required: 5 mm hex wrench, 10 mm wrench

Locator Hole

1. Depress the push button located on the
rear of the fork tube and insert the handlebar
steer tube onto the fork tube. The push button
should align with the locator hole in the
handlebar steer tube and lock the steer tube
securely in place. Once the push button pops
out of the locator hole, lift up on the steer tube
to ensure it cannot slide off. If it cannot, then
proceed to step 2.

3. Locate the 3 small, black clips that are
pre-installed on the trottle cable - they look like this >>>
They slide easily along the cable, and are designed to
be inserted into 1 hole on the scooter neck and 2 holes
on the steering column, to keep the throttle cable located
in a clean, safe position. Simply align each clip with its
respective hole (as shown) and press it firmly into place.
Do not remove clips from the cable before inserting.

2. Tighten the bolts with the 5 mm hex
wrench and 10 mm wrench. Tighten bolts
evenly and securely.

5Questions or concerns? Visit our website at www.pulsescooters.com for replacement parts and technical support, or call [phone].