Pulsar Masterpiece 216, Masterpiece 108, Masterpiece 48 User Manual

MASTERPIECE
MANUAL
Masterpiece 216
Masterpiece 108
Masterpiece 48
Masterpiece
Software
Upgrades
NEW IN SOFTWARE VERSION "MASTERPIECE MAIN No.1.i" - 12-03-91
The Remote Control DIN Socket is operational - see appendix 4. This allows great scope for expanding the system
- for example a number of Masterpieces can be used to control different sections of equipment under the control of a "master" Masterpiece.
Improvements in the operation of 1 shot chases.
Security Code - rather than any 4 key presses on the Keyboard, the correct security code is now required for
Memory to Card, Card to Memory, Swap Memory and Card (both keys together) and now for Set User Access Levels.
The security code has a fixed value of: 12, 6, 7, 1.
If a Keyboard key is not pressed within 5 seconds, the program mode required is cancelled and the word "CNCL" is displayed. The word "FAIL" is displayed if the wrong code is entered.
Set User Access Levels (SUAL) - to enable or disable any slider or pad. For example, to allow the operator the use of an Environment Keyboard of pre-programmed effects but disable everything else to prevent accidental corruption of the program or changes to the show.
Operation: press the SUAL key, enter the code, after the correct code the word "SUAL" is displayed, now all the LEDs show whether a pad or slider is currently accessible or not. Touch a pad to change its accessibility - the LED changes state and the display shows "ON" / "OFF". For sliders, move the slider to change its accessibility - if the slider is over 50% its LED is on and it is accessible, at less than 50% its LED is off and the slider is disabled. Press the SUAL pad again to finish. The word "DONE" is displayed or "CNCL" if no changes have been made.
When a pad or slider is disabled, its level before entry to SUAL is permanently maintained.
Touching a disabled pad makes the SUAL LED flash and puts the word "SUAL" in the display. Moving a disabled slider also makes the SUAL LED flash but puts the slider's level in the display to "view" it.
SUAL mode may be used during a show without affecting the performance.
Parking Sliders at 0 no longer engages them to zero level Channels/Keyboard Masters.
Concurrent Programming - besides SUAL, the other programming functions - Save Output To Scene, Program
Chase Sequence and Save Environment of Channels Scenes and Chases all run concurrently with the light show without affecting it.
Release All - (Release + Slider Action pads together), is now available to release any slider from having overriding control of an output Channel Level on any of the 6 Output Select pages or of a KeyBoard Master level on any of the 18 KeyBoards.
Continued...
Paul F. Mardon, Technical Director, 28-10-98
File: MPN.Sam PAGE 1 of 11
Masterpiece
Software
Upgrades
NEW IN SOFTWARE VERSION "MASTERPIECE MAIN No.1.3" - 17-05-91 continued
Automatic Release and Replace - when you Save Output To Scene (SOTS) or Save Environment of Channels,
Scenes and Chases (SESC), all sliders are RELEASED and all KeyBoard pads are turned off. The Scene or Environment which you have just saved is switched on to REPLACE them.
Should you NOT want this facility to operate, hold your finger on SOTS or SESC until AFTER you have removed your finger from the KeyBoard pad.
Environment Chases - The 6 Environment Chases are now available with Auto and Manual stepping. Each one may
have up to 124 steps. They are programmed in the same way as Scene Chases except that after pressing "Program Chase Sequence", you select one of the 6 Environment Chases on Environment Keyboard No.3, Keyboard pads 1-6 and then the steps you enter are Environments rather than Scenes. Forward and Reverse Manual Step pads can be used for editing just the same - see Page 5.6 of the Manual.
The Black Out key "b.O." may be used during Scene or Environment Chase programming to enter a blank step - it too blinks to indicate availability if no key is pressed within 5 seconds.
Fine details:
Automatic Release and Replace no longer forces the Scene or Environment KB into latch but leaves the choice of Keyboard Action to the user.
Improved blinking of KB LEDs when engaged to KeyBoard Master sliders.
The accessibility of the Memory to Card pad (only) is not updated during Card to Memory transfer which would inevitably make it accessible.
Environment Chases - The 6 Environment Chases are now also operational in Real Time. Pressing the "Chase
Step Source" pad OR the "Record Environment Chase in Real Time/Step Times" pad when "Which Chase" is an Environment Chase, will step through: Step Times, Real Time, Auto and Manual (Bass and Treble are not appropriate).
There are two methods of recording the times for each step in Program Chase Sequence (PCS) for Environment Chases:
1. Real Time. Normally used for recording and replaying a show. Perform your show, pressing the Environments you require on cue. The Masterpiece records the moment when you entered each step, to a resolution of 0.02 seconds, ready to recreate your show on playback.
2. Step Times. Normally used to enter the longer step times needed for environmental control. After you enter the Environment for each step of the chase, the step number is displayed for 2 seconds, then you can use the Joy Stick to view (X axis) or adjust the time (Y axis) from this step to the next one. The maximum time per step is 3 days, 21 hours, 12 mins, 24.30 secs. There are 124 steps available - over 15 months are possible before repeating!
Continued...
Paul F. Mardon, Technical Director, 28-10-98
File: MPN.Sam PAGE 2 of 11
Masterpiece
Software
Upgrades
NEW IN SOFTWARE VERSION "MASTERPIECE MAIN No.1.5" - 10-07-91 continued
Editing times - two methods - regardless of whether the Environment chase was made in "Real Time" or "Step Time"
mode:
1. Re-enter PCS in Real Time mode, press Forward Manual Step on each cue of your show. The timings of your presses replace the existing times.
2. Re-enter PCS in Step Times mode, use Forward Manual Step to see the Environment for that step when pressed, the Step Number for two seconds when released, then you have use of the Joy Stick to view (X axis) and change the times (Y axis).
It is not possible to see all 9 digits of the step time at once so Joy Stick X allows you to window through the time, alternately displaying part of d.hh. ' '. " ".th and the step time figures.
d. h h. ' '. " ". t h Time display - use Joy Stick X axis to window through the step time, d h h m m s s t h use Joy Stick Y axis to change the time. a o o i i e e e u y u u n n c c n n When running an Environment Chase, "Step Times" and "Real Time" work s r r u u o o t d identically and like "Manual", they use the Slope slider to set the fade in and out
s s t t n n h r times.
e e d d s e The start time for a real time Environment Chase is the moment when it is s s s s d switched on, either by pressing the pad or by switching on the mains supply to
t the unit where the required Environment Chase was running at switch off. h s All chases start at step 1 at switch on.
To perform a pre-recorded show, start the music, if your show starts on the first beat for example, hit the Environment Chase pad in time with it, the rest is automatic.
To control the lighting of a museum for example, one could power the Masterpiece from a time clock which switches on at 8.00am, then the steps of the Environment Chase control the lighting for the rest of the day.
The Memory Card's Battery Voltage is displayed when a Card is inserted. The words "Good" (>2.75v), "FAIR" (2.5-2.75v) or "Lo" (<2.5v) are also displayed. The display continues to monitor the voltage until any other key is pressed or slider moved. Memory to Card and Card to Memory are not allowed if the battery voltage is low - "FAil" is displayed. This guards against: no Card, no battery, battery in back to front and a flat battery. (Should the transferred data not verify correctly, "FAIL" is displayed).
Fine details: • Pressing Forward or Reverse Manual Step before the fade is finished no longer loses a step - the step forces the completion of the fade. • The software will now read correctly from the newly available "Write Protected" Memory Cards while their protection is switched on.
Improvements to the operation of the Remote Control Socket:
The response time of the RC socket is now extremely fast - important when the unit is a slave in a multiple Masterpiece system. The RC signal can now drive Environment Keyboards which are in Flash and Solo modes as well as Latch and Swap modes. The RC signal works correctly even if all the Keyboard pads have been made inaccessible. It will not leave an inaccessible Keyboard selected but returns to the previous one after an input in this case. Input codes 57-63 have been removed and are reserved for special functions. So far just code 63 is in use and allows you to remotely transfer Card to Memory.
Also see Appendix Four of the Manual.
Paul F. Mardon, Technical Director, 28-10-98
File: MPN.Sam PAGE 3 of 11
Masterpiece
Software
Upgrades
NEW IN SOFTWARE VERSION "MASTERPIECE MAIN No.1.6" - 06-09-91 continued
Selective Memory Transfer: After pressing Memory-to-Card, Card-to-Memory or both for Swap Memory and Card,
all the 18 Keyboard Select LEDs light up, allowing you to turn off any Keyboard you don't want to transfer. Do this only if required and then enter the Security Code as usual. This allows the expert programmer to pick and mix parts of various shows together to create a new one - eg. using the Scenes from one show with the Chases and Environments of another.
The MIDI socket is now fully operational - BUT only if the DMX/MIDI EPROM in the Masterpiece is ALSO upgraded to "DMX/MIDI V1.3". A MIDI signal selects the Masterpiece's Environments and Environment Chases - see Appendix Three for full details.
"Use Scene Fade Times" key, previously not in use, now has the following effect: LED on - Fade in the chase at switch on, LED off - Step in the chase with the first Scene/Environment at full -
sometimes needed for control of intelligent lighting.
NEW IN SOFTWARE VERSION "MASTERPIECE MAIN No.1.7" - 06-02-92.
Switching Sound-to-Light (S2L) on Zone 3. Useful for a dramatic effect or for producing a better result from
devices with significant response times such as PAR64 lamps, Pin Spots or Golden Scan stoppers. Zones 1 and 2 continue to have modulated S2L with the full range of dimming.
Treble & Bass Burst are now available for Scene Chases, providing a whole range of super effects. With the SPEED control high, a burst of steps is produced for the duration of the beat. With the SPEED control low, a single step is produced on the beat. The SLOPE control gives two options. With the SLOPE control >50%, the chase STEPS from one step to the next. With the SLOPE control <50% the chase FADES from one step to the next - giving some lovely effects at low SPEED settings - partial fades towards the next step during the beat followed by frozen movement between beats.
Bass Bounce ("bASS") replaces Bounce/2 ("RRFF") for Treble Burst, Bass Burst and Auto scene chases providing more super effects. Manual and all Environment Chases retain Bounce/2.
All Off - Release Sliders + Slider Action does "Release All sliders" but now if both keys are kept pressed for 3 seconds, all Scene, Chase and Environment keys are also turned off.
Two Security Codes - only the new "Programmer's Code" will now allow entry to Set User Access Levels. The existing "Operator's Code" (12, 6, 7, 1) now only allows Card / Memory transfer.
The Forward & Reverse Manual Step keys show the Step Number, at finger off, of the Chase to which the Chase Controls are engaged. This facility works in Treble, Bass and Auto as well as Manual.
The Masterpiece Screen Driver unit will be available from Q2 1992. This will be an optional add on unit to the Masterpiece. Amongst other facilities, it provides:
On screen help in many languages by holding down a key for more than 0.5 seconds,
A User Text Area for each Output Select Page and Keyboard where you will be able to enter details of your Channel Assignments, Scenes, Chases, Environments, etc. in full colour, using the Masterpiece keys for text entry,
A Bar Graph display of the levels of the Output Channels.
Version No.1.7 of the Masterpiece software transmits all the key press and ASCII text information ready for the Screen Driver unit. This is mixed in with the existing PMX (Pulsar MultipleX) data stream from the Masterpiece.
Paul F. Mardon, Technical Director, 28-10-98
File: MPN.Sam PAGE 4 of 11
Masterpiece
Software
Upgrades
NEW IN SOFTWARE VERSION "MASTERPIECE MAIN No.1.7" - 06-02-92 - Continued
Two Security Codes - only the new code will now allow entry to Set User Access Levels.
The new Programmer's Code -
2, 3, 11, 10
is now required to enter Set User Access Levels. It also works for Card / Memory transfers.
The Operator's Code -
12, 6, 7, 1
is the same as before but now ONLY works for Card / Memory transfers.
* * * * * REMOVE THIS SHEET * * * * *
if you don't want the Lighting Operator to be able to change the User Access Levels.
Paul F. Mardon, Technical Director, 28-10-98
File: MPN.Sam PAGE 4a of 11
Masterpiece
Software
Upgrades
NEW IN SOFTWARE VERSION "MASTERPIECE MAIN No.1.8" - 24-07-92.
From version No.1.8 two EPROMs are available:
"Masterpiece 108 MAIN No.1.8"
and
"Masterpiece 48 MAIN No.1.8"
Production of the Masterpiece 48 started in July 1992 using this software version from the beginning. All planned features of the MP48 are available and working. However, as the MP48 can replay programs made on the MP108, you may like to keep its software upgraded as more facilities become available on the MP108. BUT be sure in future to specify whether you need software upgrades for the MP108 or the MP48.
Obviously the Masterpiece Manual is in a temporary phase so for the time being if you are a MP48 owner, you will find references to facilities only available on the MP108 - please bear with us.
NEW FEATURES:
The MIDI input (MP108 only) can now respond to all 128 MIDI notes. In addition to giving control of the three Environment Keyboards, Scene Keyboards 10 & 11 are accessed using notes 0-35 and Scene Chase Keyboard 3 by notes 99-116. Please refer to the June 92 or later version of Appendix Three for full details.
Environment Chases can now be driven by Bass, eg. from a Click Track accompanying a music tape. On the MP108 Real Time and Step Times are the same in playback leaving the fourth option available as Bass.
Chase Direction - the Bounce/1 mode "RFRF" has been replaced by Alternate "ALt". In ALt mode, each time a chase is switched on it runs in the opposite direction. This allows you to produce a more varied and interesting light show without extra programming. Should you still want to produce a Bounce, just enter the extra steps when programming the chase sequence.
Flash - when the sliders are acting as Keyboard Masters and have control of the levels of Scenes, Chases or Environments, the Keyboard keys are now able to flash them to full.
Card To Memory will not read from Masterpiece Screen Driver Cards.
Improvements to the operation of the LEDs in SUAL mode.
NEW IN SOFTWARE VERSION "MASTERPIECE MAIN N.1.85" - 20-06-93.
Remote Blackout (R.b.O.) by MIDI or Remote Control. A Blackout can now be forced remotely by MIDI or via the
Remote Control Socket as is sometimes required by Fire Authorities - see Appendix 3 and Appendix 4.
All Off can now be done from MIDI - note number 127.
Robust Operation. To prevent you having to make those panic midnight calls to the installer we have made the
following changes to make the software (we hope) virtually bomb proof provided you saved your work on a Card
Card to Memory is always accessible, After Card to Memory the Grand Master is always 100%, After Card to Memory the Output Select and Keyboard Select are changed to those stored in the Card, Card to Memory still works even if the Masterpiece's memory has been corrupted (eg by loading from a partially inserted card) or if so many things are switched on that the Watchdog Timer cuts in and all the LEDs are blinking
- commonly known as "Brain Overload".
Bug Fixes: • Switching the mains off and on in SUAL changed the chase keys' accessibility. • Environment chases in MP108 said "S.t." when they should have said "bASS". • The MP48 Remote Control Socket didn't work the Environment Chases correctly with certain Keyboard Actions.
Paul F. Mardon, Technical Director, 28-10-98
File: MPN.Sam PAGE 5 of 11
Masterpiece
Software
Upgrades
NEW IN SOFTWARE VERSION "MASTERPIECE 108 MAIN No.1.9" - 28-09-93.
FADE IN and OUT TIMES. Although printed on the front panel as "SCENE FADE TIMES", the system has been
enhanced beyond that originally planned, to give Fade IN and OUT Times to SCENE CHASES as well as SCENES. Environments and Environments Chases don't have Fade Times but of course the Scenes and Scene Chases they contain can. Note: The Scenes within a Scene Chase can have fade times if required.
Overriding Global Control of all Fade In and Out Times is achieved by moving the IN and OUT sliders to engage them (LEDs blinking) and choosing suitable Fade In and Out times. These slider values then operate for all Scene and Scene Chase Fade In and Out times, overriding the individual fade times stored with them.
Cancelling Global Control of all Fade In and Fade Out Times. While pressing Release Sliders, move the IN and/or OUT sliders to release them from having overriding control. The Fade In and/or Out times stored with each Scene and Scene Chase now operate. Release All - Release Sliders & Slider Action together, also releases the IN and OUT sliders.
Old Memory Cards. When loading a show from a Memory Card made with an earlier version of software:
All the Fade In and Out Times stored with the Scenes and Scene Chases are set to zero. The IN and OUT sliders are set to zero and made inaccessible.
These ensure that your show will work with the 1.9 software exactly as it did before.
To Save a Scene's Fade Times the IN and/or OUT sliders need to be engaged (LEDs blinking) when you do "Save Output To Scene" - otherwise the Scene's own existing values remain.
To Modify a Scene's Fade Times: switch on the Scene (on its own, and allow it to fade to full if it has a fade in time), adjust the IN and/or OUT sliders to the required times, save the scene back to itself.
To Save/Modify Scene Chase Fade Times the IN and/or OUT sliders need to be engaged (LEDs blinking) and the Controls Engaged LED needs to be on, when you do "Program Chase Sequence plus Select the Chase to be programmed" - otherwise the Scene Chase's own existing values remain.
Seeing the stored fade times. When you switch a Scene or Scene Chase on or off, the display shows (sequentially) the IN and OUT times, and for Scene Chases, the SPEED and SLOPE as well. Also, provided the IN and/or OUT sliders are not engaged, their LEDs will be updated with these fade time values for a rough indication. VIEW may be used to give an accurate read out - move the IN or OUT slider WHILE an Output Select or Keyboard Select key is pressed.
Enhancements to the VIEW system. (The VIEW system puts useful information in the display. It is activated by moving a Slider or pressing a Key WHILE an Output Select or Keyboard Select key is pressed. No levels or functions are changed in the process.) New features:
While holding an Output Select key pressed, pressing a Keyboard key displays the Channel Number (C. 1 - C.108) followed by the Channel's Level at finger off. While holding a Scene Keyboard Select key pressed, pressing a Keyboard key displays (sequentially) the
Scene's Fade In and Out times. While holding a Scene Chase Keyboard Select key pressed, pressing a Keyboard key displays the Scene Chase's Fade In and Out Times, its Speed and its Slope and connects this chase to the chase controls
without having to switch it on or off. NB. For Manual chases and Real Time / Step Time Environment Chases, the Slope is the crossfade time in seconds.
Tip - to see if any Scenes or Scene Chases have fade times, ensure the IN and OUT sliders are released, then, WHILE pressing a Keyboard Select key, run your finger across the Keyboard watching the IN and OUT LEDs.
Remote Swap Memory and Card is now possible from MIDI and the Remote Control Socket. See Appendix Three
- Remote Control by MIDI and Appendix Four - Using the Remote Control Socket.
The Grand Master Level is now loaded from a Memory Card (when loading from old cards it is put to 100%).
Paul F. Mardon, Technical Director, 28-10-98
File: MPN.Sam PAGE 6 of 11
Masterpiece
Software
Upgrades
NEW IN SOFTWARE VERSION "MASTERPIECE 108 MAIN No.2.0" - 15-07-94
54 KEYBOARDS! Select Latch + Swap and then press the "Swap - This Keyboard / All Like Keyboards" key. You
will find that this key now has three possibilities - "ALL", "thIS" and the new one "SP.3" with no LEDs on. "SP.3" means Swap 3. Swap 3 turns any of the 18 way keyboards into three 6 way keyboards - swapping between 1-6, 7-12 and 13-18. This makes more efficient use of the Scenes, Environments etc. and gives you power and versatility. Practical Examples:
For Scan use, this could give you 6 Colour looks + 6 Gobo looks + 6 Iris/Frost/Prism looks all immediately accessible on the same 18 way keyboard. The Out Station on the Remote Control socket can now access nine 6 way swapping keyboards and MIDI can access 18 of them.
COPY FADE IN TO FADE OUT TIMES. Gives the Masterpiece the power of a top of the range Theatre or Scan Lighting Board. It allows you to move from any Cue to any other Cue with a perfect Dipless Crossfade. Your "Cue" can be a Scene, Scene Chase, Environment or Environment Chase. See the attached "Out-Times Flowchart" on page 9 for a diagrammatic explanation.
Global control of matched In and OutTimes may be taken by engaging just the InTime Slider in Copy Mode ­sufficient for many purposes.
With the time sliders released, the times stored in the Scenes and Scene Chases take over. In Copy Mode the InTime of the new Scene/Scene Chase provides the OutTime for the outgoing one. This may be anything
from a zero time snap to a 360 second fade. The location of the InTime captured to become the OutTime follows this priority sequence: the outgoing key's Swap3 keyboard or 18 way keyboard, the last key pressed in All Like Keyboards, its own stored OutTime.
Practical Examples:
For Theatre use. Proceed from Scene to Scene using Swap, Swap 3 or Latch and the fades will always be dipless no matter where you are coming from or going to. For Scan use. Environments may contain such components as: Colours from a colour keyboard, Gobos from a Gobo Keyboard, Positions or Position Chases from their keyboards. AND NOW THE POWER - when you swap from Environment to Environment, all their components will crossfade or snap individually and diplessly using the InTimes associated with the incoming Environment's components.
To toggle between Copy In to Out Mode and Individual Mode: WHILE pressing the COPY key, move either the In or OutTime slider. The display shows "COPy In tO OUt" or, if Copy Mode has been disengaged, "the time in seconds". While the In or OutTime sliders are moved in Copy Mode the Copy key LED lights.
Over The Top for your job? No worries - the beauty of Masterpiece is that although we are progressively giving it more and more power so that you can use the same controller for any application, you only have to use the parts you want. For example, if you don't need fade times, simply engage the In and OutTime sliders to zero (LEDs blinking) and then use SUAL to lock them away. The fade times will now be inactive and we have now made the LEDs blink only faintly when disabled at zero so as not to be offensive.
A-B CROSSFADE MODE is ideal for Theatrical or Live use. Each of the 18 Keyboards can have its Keyboard Action selected to "A-B Crossfade Mode" individually. The A and B sliders can then be used to fade smoothly between Scenes, Scene Chases, Environments and Environment Chases or even combinations of them. Keyboard keys may be pressed to connect them to the A or B slider or disconnected by pressing them again - the word "FREE" is displayed. A key which is OFF and is to be faded in will connect to whichever of A or B is at zero. A key which is ON and is to be faded out will connect to whichever of A or B is at FULL. Should the sliders not be at an end you will see the error message "A-b Not At 0.0" or "A-b Not At 100.0". The LEDs of incoming keys shimmer green, while the LEDs of outgoing keys shimmer red, corresponding to the A and B LEDs to which they are connected. The Scene and Scene Chase fade times still operate in A-B mode - slowest takes priority.
Paul F. Mardon, Technical Director, 28-10-98
File: MPN.Sam PAGE 7 of 11
Masterpiece
Software
Upgrades
NEW IN SOFTWARE VERSION "MASTERPIECE 108 MAIN No.2.0" - 15-07-94 - continued
Limits: A maximum of 38 keys may be attached to the Incoming slider and 38 keys to the Outgoing slider - which
should be enough! The display shows "FULL" if more than this number is attempted.
Copy A to B allows you to have individual A and B sliders to achieve "Split Fades" or to use the A slider alone for a perfect dipless crossfade.
To toggle between Copy A to B Mode and Individual Mode: WHILE pressing the COPY key, move either the A or B slider. The display shows "COPy A tO b" or, if Copy Mode has been disengaged, the A and B sliders' percentages. While the A or B sliders are moved in Copy Mode, the Copy key LED lights.
Grand Master for Generic Lighting. Lighting designers sometimes want to dim the level of the generic lights without affecting the intelligent lights. In other words they need a selective Grand Master. This can now be achieved by attaching the required generic Scenes / Chases / Environments to the A or B Master.
JOYSTICK VELOCITY. Key S12.18 is not a normal scene but switches the action of the JoyStick between Position (LED off) and Velocity (LED on). The velocity software has been carefully written to profile the behaviour of the JoyStick from very slow, gentle movement near the centre for follow spot use, to very fast movement at the extremities. When you let go of the JoyStick, it returns to the centre and the movement stops where it is. There is a central dead band from 48 to 52 - Left and Down movement is from 47 and below while Right and Up movement is from 53 and above.
Attaching a single projector to the JoyStick. Move its Pan slider upwards to see which way the light beam moves relative to the orientation of your JoyStick. Now save its Pan at 100%, on its own, to the Left/Right/Up/Down Scene corresponding to the direction in which it moved. Do the same for the Tilt. Switch on just these two Joy Scenes and select Position or Velocity to connect the JoyStick to the projector's mirror.
Follow Spot Control. You may wish to limit the movement of the light beam to just the stage area. Proceed as above but set up four Scenes containing the Left and Right limits for Pan/Tilt and the Up and Down limits for Tilt/Pan. Switch on all four Joy Scenes and select Velocity.
Joy Centre: With the Joy Centre Scene turned off, the Joy Left Scene, for example, is scaled from 100% with the JoyStick fully left to 0% with the JoyStick fully right. With the Joy Centre Scene switched on, the maths changes. The Joy Left Scene now scales from 100% (Left) to 0% with the JoyStick in the Centre (or beyond), while the contents of the Joy Centre Scene are scaled from 0% (Left) to 100% in the centre. The same concept applies to the Right, Up and Down Scenes. Interesting new effects are possible - particularly to those who feel like experimenting to see what this new dimension can offer! One suggestion for Position mode is to make the Joy Centre scene the required position when you let go of the JoyStick.
ENHANCEMENT to the VIEW system. While holding an Output Select key pressed, pressing a Keyboard key displays the Channel Number (C. 1 - C.108) followed by the Channel's Level at finger off. NEW FEATURE - the channel level continues to display until you press another key. This allows you to follow the progress of a chase or crossfade.
BUG FIXES:
The Dipless Crossfade maths has been rewritten so that a channel level, which is the same in the incoming and outgoing scenes, remains completely constant during the fade. This applies to crossfading chases as well as timed fades.
If a Keyboard Master is controlling the level of a key, that key may be flashed to full - but no longer in VIEW or a Program Mode.
Paul F. Mardon, Technical Director, 28-10-98
File: MPN.Sam PAGE 8 of 11
Out-Times Flowchart
(How to use Copy In to Out Mode to
achieve Perfect Dipless Crossfades)
KEY
Where do
OUT-TIMES
come from?
Is the COPY IN to OUT
mode selected?
(While pressing COPY key, move
IN or OUT to select/deselect)
Y
Are the IN (and OUT) TIME
sliders engaged (LEDs blinking) ?
Original 1.9 Fade Time Logic
N
Is the OUT-TIME slider engaged
(LED blinking)?
N
Y
Version 2.0... Fade Time
Enhancements
Y
Use time from OUT-TIME slider
Use the Scene / SceneChase's
own OUT-TIME stored with it at
S.O.T.S. / P.C.S.
Use time from IN-TIME slider
N
Is there a Scene / SceneChase
fading in on this keyboard ?
(3x6 or 1x18 way keyboard)
N
Is this keyboard in Swap-All Like
Keyboards AND was the last key
pressed a Scene / SceneChase
on a Like keyboard
N
Y
Y
Paul F. Mardon, Technical Director, 28-10-98
File: Out-Time.Sam PAGE 9 of 11
Use the IN-TIME found on this keyboard as the OUT-TIME for any fade outs on this keyboard
Use the IN-TIME of last
Scene / SceneChase
pressed as the OUT-TIME
(for Swap-All Like Keyboards)
Use the Scene / SceneChase's
own OUT-TIME stored with it at
S.O.T.S. / P.C.S.
Masterpiece
Software
Upgrades
108 Masterpiece PMX Output Channel to 256 DMX Slot, Patching System.
This vastly expands the capability of the Masterpiece 108 by allowing it to drive 256 DMX Slots.
Why the name "Slot"? It is expected, in the next revision of the DMX Standard, that the term "Dimmer Levels" will be renamed "Slots", since DMX is now used to control many parameters besides dimmer levels. Slots refer to the bytes that flow one after the other in the DMX serial data stream - each having its own time slot. It aids our explanation of the Patching System to refer to Masterpiece Output Channels or PMX Channels (Patch input) as opposed to DMX Slots (Patch output).
Patching Concepts:
Please see the Masterpiece Hierarchy diagram to see how the Patch fits into the scheme of things.
The Patch is particularly useful when controlling large numbers of intelligent lighting fixtures. For example, a Masterpiece 108 can control just 6 Clay Paky StageScans but with the Patch it can now control 16 of them!
Often when intelligent lights are programmed, certain parameters are grouped together into Scenes. For example, you might have a Scene which controls the colour discs of the odd number projectors and another scene for the even one's colour discs. A scene for odd Gobo Selects and another for even Gobo Selects. Two scenes for odd and even Gobo Rotation speeds. Two scenes for the front group and the back group's Zoom Lenses. One scene for all the lamp control channels, etc.
This grouping can now be done by the Patch, for example, this allows just one Masterpiece Channel to control all the Lamp Control Slots. With 16 projectors this saves 15 Masterpiece Channels. Two Masterpiece Channels to control the odd and even colour discs - 14 channels saved. Two Channels to control the odd and even Gobo Select discs - another 14 channels saved, and so on. It is likely, however, that you will want to control the Pans, Tilts and Stoppers, for example, individually, but with these huge channel savings this presents no problem.
Logical layout - another function of the Patch is to allow you to lay out the Masterpiece in an efficient and logical way. All the Irises could be patched to adjacent channels on the Masterpiece. Similarly the Stoppers. The Pans and Tilts could be put side by side on the same Output Select Page, etc.
If you have some spare DMX Slots, you could address your projectors 10 or 20 apart for simplicity, leaving some unused Slots between projector base addresses.
The Patch Key has three modes: Patch Off, Patch On and Program / View. Patch Off - the Masterpiece works as before - the DMX Slots are identical to the PMX Channels. Patch On - the Masterpiece's 108 PMX Output Channels are patched to 256 DMX Slots.
The PMX output is always unpatched and therefore exactly as it was before, as are the 36 0-10V analogue outputs.
Programming or Viewing the Patch
One Masterpiece Channel can drive many DMX Slots but a DMX Slot can only be driven by one Masterpiece Channel. Therefore the programming process is to select a particular DMX Slot and then attach a Masterpiece Channel to drive it.
1. Press the Patch key to select Prog/View and enter the (new) Security Code.
2. Press the Forward or Reverse Manual Step keys to work your way through the 256 DMX Slots. These keys are repeat keys and quickly count through the slots if held pressed. The display shows "S.###" (meaning Slot Number) while the Forward or Reverse key is pressed and "C.###" (meaning output Channel Number) when the key is not pressed. When not pressed, after two seconds, the display toggles between "S.###" and "C.###".
3. Having selected a particular Slot, use the Output Select keys O1-O6 and the Keyboard keys 1-18 to select the Masterpiece Channel to drive that slot. "C.###" appears in the display.
Paul F. Mardon, Technical Director, 28-10-98
File: MPN.Sam PAGE 10 of 11
Masterpiece
Software
Upgrades
NEW IN SOFTWARE VERSION "MASTERPIECE MAIN No.2.1" - 28-10-98 - continued
4. Additional Feature - a DMX Slot may be given a permanent fixed level - rather than attaching it to a Masterpiece Channel. This can be useful for house lights, for motors which must always run or to ensure certain slots are always on or off, etc. To do this use the Grand Master during patch programming to set the desired level of the Slot. You can also move the Grand Master to see which parameter a particular Slot controls and then press the desired Keyboard key to return the Slot to Masterpiece Channel control. When a Slot has a fixed level the display changes from "C.###" to "###.#" to show its percentage. Forty levels of brightness are available from
0.0% to 100.0%.
5. To finish Prog/View Patch, just press the Patch key once more.
Blinking LEDs - if you don't press an appropriate key or move the Grand Master within 6 seconds, the LEDs start to blink to show you which keys should be pressed.
Sacrifice - to provide the necessary memory for the Patch, some of the memory that was used by the 6 Environment Chases has been taken. These can now have a maximum of 102 steps each instead of the 124 they were allocated previously. So DO NOT use this new software if you have Environment Chases with more than 102 steps and you cannot reprogram them to be within the 102 limit.
Patch Memory / Card Transfer - each of the 18 Keyboards may be enabled or disabled for transfer during memory to card or card to memory. Please note that the Patch information is transfered with the E3 keyboard.
New software for the Masterpiece Replay Unit is also available. This allows the Replay Unit to replay shows made on the Masterpiece 108, which use the Patch and 256 DMX channels. The software needed is: EPROM - Masterpiece Replay Unit, Main No.2.1, © Pulsar 28-10-98 (or later) DMX Microprocessor - M/Piece 108 / RPU, DMX / MIDI V2.1, © Pulsar 28-10-98 (or later).
New software for the Masterpiece Screen Driver is being written. This will be a free upgrade which we hope will be available very early in 1999. While in Prog/View Patch it will automatically display the Patch's Channel Map as you program it and to allow you to type in the function of all the 256 DMX slots. We expect there to be 13 Screens of Patch data - 20 Slots per screen. Using the Forward or Reverse Manual Step keys to select a Slot will put you into the correct screen. The Masterpiece Channel driving that Slot will automatically be shown. While in Prog/View Patch you will be able to use Screen Text Mode to enter details about that Slot's function. If you keep Output Select O1-O6 pressed, the screen of data about those Masterpiece Channels will be displayed to help you select the desired Channel. The Masterpiece software necessary to do this is already built into the 2.1 upgrade.
OTHER NOVELTIES New Security Code for Set User Access Levels and for programming the Patch - see the Security Code sheet. The
Operator's Code 12,6,7,1 now only works for Memory / Card transfers. "Appendix Two - Pulsar Masterpiece - Remote Control by RS232." This explains how to control a Masterpiece
108 from a computer or other source of RS232 / RS423. It shows how to do anything from activating a single channel to a complete lightshow remotely. The concept is similar to "Remote Control by MIDI" in Appendix Three.
Controls Engaged / Which Chase? The key's LED now blinks when engaged to warn that moving the Speed or Slope sliders or touching a Chase Control key will change the parameters of the engaged chase.
BUG FIXES
If the Scene Fade Time sliders are brought to zero they no longer become engaged until they move away from zero - just like the Channel Level / Keyboard Master sliders. Coming out of Program Chase Sequence after editing the Step Times of an Environment Chase no longer flips it into Bass Burst mode. Switching off the Masterpiece stops the DMX transmission cleanly - without sending incorrect levels first.
NEW IN SOFTWARE VERSION "MASTERPIECE 108 MAIN No.2.2" & "REPLAY UNIT MAIN No.2.2" - 28-09-99 BUG FIX - occasional loss of MIDI Remote Control comands - problem solved in version No.2.2.
Paul F. Mardon, Technical Director, 28-09-99
File: MPN.Sam PAGE 11 of 11
Masterpiece
Software
Upgrades
NEW IN SOFTWARE VERSION "MASTERPIECE MAIN No.2.1" - 28-10-98
SECURITY CODES
The NEW Programmer's Code:
3, 4, 10, 9
This code is required to enter: Set User Access Levels and to Program / View the Patch (the 108 PMX Channel to 256 DMX "Slot" patching system released in Software Version 2.1 as a free upgrade, which allows a Masterpiece 108 to drive 256 DMX channels or "slots").
This code should not be disclosed to people you do not want to program your Masterpiece.
The Operator's Code:
12, 6, 7, 1
This is now the ONLY code that allows Card / Memory transfers.
* * * * * PLEASE REMOVE THIS SHEET * * * * *
if you do not want the Lighting Operator to be able to change the User Access Levels or to Program / View the Patch.
Paul F. Mardon, Technical Director, 28-10-98
File: MPN.Sam PAGE 11a of 11
Masterpiece
108 PMX Channel to
256 DMX Slot
Patch - Examples
Software Upgrade from No.2.1 (free) for the Masterpiece 108 provides a Signal Patch.
This allows the 108 Masterpiece PMX Channels to be patched to drive 256 DMX Slots (channels). Thus, for example, up to 16 Clay Paky Stage Scans can now be controlled whereas before the patch upgrade, only 6 could be controlled!
The Patch groups projector channels together - just as you would have often done in practice but previously by using Scenes. Now each Masterpiece channel is able to control groups of projector channels, vastly expanding the Masterpiece's capabilities.
In the table below various example arrangements are shown but the groupings can of course be varied to suit the requirements of your particular show.
If, for example, Prism Select has the number 2 in the table, this could mean that Odd Projector Prism Selects are controlled by one channel and Even Projector Prism Selects are controlled by a second channel.
Number of Stage Scans Driven ðð
Stage Scan Channel òò
No Function No of Masterpiece PMX channels used per function
1 Iris 4 12 8 6 2 Colour Disc 2 4 4 6 3 Prism & Frost 2 4 4 6 4 Dimmer/Strobe 16 12 8 6 5 Pan 16 12 8 6 6 Tilt 16 12 8 6 7 Multi Step Zoom 4 4 4 6 8 Focus 16 12 8 6
9 Prism Select 2 2 4 6 10 Prism Rotation 2 2 4 6 11 Fixed Gobo Select 2 3 4 6 12 Rotating Gobo Select 4 4 8 6 13 Gobo Rotation 8 12 8 6 14 Red 4 4 8 6 15 Green 4 4 8 6 16 Blue 4 4 8 6 17 Lamp Control 0 1 1 6
16 12 8 6
No of Masterpiece PMX channels used ðð
No of DMX slots (output channels) driven ðð
106 108 105 102 256 204 136 102
Paul F. Mardon, Technical Director, 28-10-98
File: PatchEg.Sam PAGE 1 of 1
Masterpiece 216
Enhanced
Features
THE INITIAL SOFTWARE FOR THE MP216 IS "MASTERPIECE MAIN No.2.2" - 28-09-99
Output Channels
The MP216 has 216 'PMX' Output Channels. Press the O1-O6 / O7-O12 key to switch the six Output Select keys between O1-O6 for channels 1-108 and O7-O12 for channels 109-216.
Patching System
The 216 PMX Output Channels are patchable to 512 DMX Slots (twice the capacity of the MP108).
Eight Shows
Memory capacity is provided internally for 8 separate shows.
At switch on the software version is displayed e.g. "No.2.2" followed by the number of the current show e.g. "Sho.1".
To see the number of the current show at any time, simply press the Show Select key on it's own.
To change show: WHILE pressing the Show Select key press a keyboard key 1-8. When you release the Show Select key, the Masterpiece will switch to the new show.
Each of the eight shows may be selected remotely by MIDI and RS232 (PMX) - see Appendices Two and Three.
Memory Cards
Each MP216 show needs 64K of memory (32K for a MP108). So a 64K card can store one show, 128K two shows, 256K four shows, 512K eight shows.
Memory to Card / Copy Current Show to Another Show
Any of the internal shows (Sho.1 - Sho.8) may be copied to any position in the card (Sho.9 - Sh.16). The source show is the current one. When you press the Memory to Card key the MP216 tries to select the most likely destination show, however you can change this by pressing the Show Select key plus a Keyboard key. The destination show can even be another internal show - this provides the Copy Show to Show function. As usual the Keyboard Select keys may be used to select which parts of the memory are transferred. The display indicates the source and destination shows, when you are happy with these, enter the code.
Card to Memory / Overwrite the Current Show with Another Show
When you press the Card to Memory key the MP216 tries to select the most likely source show to overwrite the current show, however you can change this by pressing the Show Select key plus a Keyboard key. The source show may be changed to any show stored in the card (Sho.9 - Sh.16) or any internal show (Sho.1 - Sho.8) - this provides the Overwrite Current Show with Another Show function. The rest as above ...
Swap Memory and Card / Swap Current Show with Another Show
Both of the above together.
Masterpiece 108 shows
The MP216 can read MP108 cards and play them back correctly. It can also write MP108 cards but obviously only the first 108 channels are functional. A MP108 can read MP216 cards and play back the first 108 channels.
Future plans
A Chase Generator for the rapid creation of complex chases and effects, and the efficient use of Scenes is planned for the next free software upgrade.
Paul F. Mardon, Technical Director, 28-09-99
File: MPN.Sam PAGE 12 of 12
MASTERPIECE 216 108 48 RU RU2 MASTERPIECE 216 108 48 RU RU2
Front Panel Features Chase Control
DMX Output Slots (Channels) 512 256 48 256 512 Forward Manual Step PMX Output Channels 216 108 48 108 216 Reverse Manual Step Scenes 216 216 96 216 216 Chase Direction Scene Chases 54 54 24 54 54 Chase Step Source Environments 48 48 22 48 48 Chase Type 1-Shot/Repeat Environment Chases 6 6 2 6 6 Fade/Step Chase In
Which Chase?/Engage Controls Output Pages 12 6 4 Speed Slider Output/Keyboard-Master Sliders 18 18 12 Slope Slider Output Monitor LEDs 18 18 12
33 33 33
33 33 33
33 33 33
33 33 33 33 33
33 33
33 33 33
33 33 33
33 33 33
Keyboard Section BNC Connector for Lamp
33 33 33
Keyboard Keys 18 18 12 Scene Keyboards 12 12 8 4 Digit Display
33 33 33 33 33
Scene Chase Keyboards 3 3 2 Environment Keyboards 3 3 2 Joy Stick
33 33
Environment Chase Keyboards 1 1 1
Mains Keyboard Action Keys On/Off Switch (on front panel)
Latch/Flash Swap/Solo Swap All Like Keyboards
33 33 33
33 33 33 33
3
33 33 33
Mains Theatre Section On/Off Switch (on back panel)
A-B Master Sliders In/Out Fade Time Sliders A-B Crossfade Mode Pad Grand Master Slider
33 33
33 33
33 33 33 33
Supply Socket
Voltage Selector
Mains Fuse
Lamp Fuse
Output Control Keys Analogue Outputs
Freeze Output Blackout/Restore
Memory Card
Card to Memory Memory to Card
33 33
33 33 33 33 33
33 33 33 33 33
33 33 33 33 33
33 33 33 33 33
PMX Output Sockets 2 2 2 2 2
DMX 512 Output Sockets 2 2 2 1 1
Audio Inputs
33 33 33 33 33
33 33 33 33 33
33 33 33 33 33 33 33 33
1-36 1-36 1-24 1-18 1-18
Speaker Level Jack Sockets 2 2 2 2 2 Other Keys / Functions Pre-Amp Level Jack Sockets 2 2 2 2 2 Show Select Set User Access Level PMX - DMX Patch Output Bank Select Release Sliders Slider Action
Sound to Light Thru Socket Circuits Monitor
33 33 33 33 33
33 33 33 33
33
33 33 33 33 33 33
33 33 33 33 33
33 33 33 33 33
Microphone Level Jack Socket 1 1 1 1 1
PMX Remote Control
33 33 33
Midi Remote Control
In Socket
Options Switch
33 33 33 33
33 33 33 33 33 33 33 33
Remote Control Programming Keys Input DIN Socket
Save Output To Scene Program Chase Sequence Save Environment Rec.Env.Chase In Real Time Rec.Env.Chase Step Times Copy Screen Text Mode
33 33 33
33 33 33 33 33 33
33 33 33
33 33 33 33
33 33 33
Dimensions
Width 19" 19" 19" 19" 19"
Height 14" 14" 10.5" 1.75" 1.75"
Depth including plugs & sockets 6" 6" 6" 8" 8"
Designer 8U Case
33 33 33 33 33
33 33 33
MPSPEC.SAM - Modified 22/09/99
Loading...
+ 41 hidden pages