Pulsafeeder 100-150 User Manual

READ ALL CAUTIONS CAREFULLY BEFORE

P/N 32040 Rev C

INSTALLING PUMP

INSTRUCTION

MANUAL

TABLE OF CONTENTS

Page

SAFETY INSTRUCTIONS ......................................................................................................................................... 2

INTRODUCTION ........................................................................................................................................................ 2

PRECAUTIONS FOR OPERATION .......................................................................................................................... 3

INSTALLATION, PIPING AND WIRING .................................................................................................................... 4

BLEED VALVE INSTALLATION (Optional) ............................................................................................................... 6

CURRENT INTERRUPTOR (Optional) ...................................................................................................................... 7

MAINTENANCE ......................................................................................................................................................... 8

SERVICE AND REPAIRS .......................................................................................................................................... 9

TROUBLESHOOTING ............................................................................................................................................. 10

PARTS LIST (EXPLODED PUMP ASSEMBLY) ...................................................................................................... 11

REPLACEMENT KITS (EXPLODED WET END ASSEMBLY) ................................................................................ 12

SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS PRIOR TO USE

Secure chemicals & metering pumps, making them inaccessible to children & pets. *** DO NOT PUMP FLAMMABLE LIQUIDS. *** Do not cut the plug or ground lug off the electrical cord. Consult a licensed electrician for proper installation or

replacement.

To reduce the risk of electrical shock-before maintenance, repair, or moving, always disconnect the power

to the pump by unplugging from wall outlet.

Always wear protective clothing, including gloves and safety glasses, when working on or near chemical

metering pumps.

** Inspect tubing regularly for cracking or deterioration and replace as necessary. (Always wear protective clothing and

safety glasses when inspecting tubing.)

** Use CAUTION to keep fingers away from rotating parts. ** If pump is exposed to direct sunlight, use a UV resistant tubing. ** Follow directions and warnings provided from the chemical manufacturer. The user is responsible for determining the

chemical compatibility with the chemical feed pump. ** Make sure the voltage on the pump name tag matches the installation voltage. If pump fails to start, check line voltage. ** Consult with local health officials and/or qualified water conditioning specialists when treating potable water. ** Always depressurize system prior to installation or disconnecting the metering pump tubing. ** If injection point is lower than the chemical tank and pump, install an anti-siphon valve. ** DO NOT MODIFY PUMP. This poses a potentially dangerous situation and will void the warranty. Hand tighten plastic

connections (Do not use wrench).

All pumps are factory tested with water. Remove tubing and thoroughly dry if the chemical being pumped

will react with water (for example sulfuric acid). * Hand tighten plastic connections (Do not use wrench). * Consult licensed plumber and electrician before installation to conform to local codes.

* NOTE: For accurate volume output, pump must be calibrated under all operating conditions.

INTRODUCTION

Series 100/150 are diaphragm-type metering pumps. A fluid is pumped from a chemical storage tank to the point of injection by the pulsing action of the diaphragm. The four check valves (top and bottom of pump head, strainer assembly, and injection assembly) keep the fluid flowing toward the point of discharge. To insure the solution being pumped can only go forward, it is important that all check valves provide positive, non-leaking backflow prevention. The wetted end (those parts that contact the solution being pumped) is constructed of SAN, PVC, TFE, Hypalon®, and polyethylene. These materials are very resistant to most chemicals. However, there are some chemicals, such as strong acids or organic solvents, which cause deterioration of some elastomer and plastic parts, such as diaphragm, valve seat, or head. Alternate materials such as Viton®, polypropylene is available on request. Contact chemical supplier for chemical compatible materials.

MANUFACTURER’S PRODUCT WARRANTY

The manufacturer warrants its equipment of its manufacture to be free of defects in material or workmanship. Liability under this policy extends for twenty-four (24) months from the date of purchase or one (1) year from date of installation or

whichever comes first. The manufacturer’s liability is limited to repair or replacement of any device or part which is

returned, prepaid, to the factory and which is proven defective upon examination. This warranty does not include installation or repair cost and in no event shall the manufacturer’s liability exceed its selling price of such part.

The manufacturer disclaims all liability for damage to its products through improper installation, maintenance, use or attempts to operate such products beyond their functional capacity, intentionally or otherwise, or any unauthorized repair. Replaceable elastomeric parts are expendable and are not covered by any warranty either expressed or implied. The manufacturer is not responsible for consequential or other damages, injuries or expense incurred through use of its products.

The above warranty is in lieu of any other warranty, either expressed or implied. The manufacturer makes no warranty of fitness or merchantability. No agent of ours is authorized to make any warranty other than the above.

For warranty and service matters within the European Union, contact the seller first or:

Pulsafeeder, Inc. Europe

Units 12 and 13, Edison Road

Highfield Industrial Estates

Eastbourne, East Sussex BN23 6PT

PRECAUTIONS FOR OPERATION

Each Series 100/150 chemical feeder has been tested to meet prescribed specifications and certain safety standards. However, a few precautionary notes should be adhered to at all times. THOROUGHLY READ ALL CAUTIONS PRIOR TO INSTALLING METERING PUMP.

1. Chemicals used may be dangerous and should be used carefully and according to warnings on the label. Follow the directions given with each type of chemical. Do not assume chemicals are the same because they look alike. Always store chemicals in a safe location away from children and others. We cannot be responsible for the misuse of chemicals being fed by the pump.

2. Always wear protective clothing (protective gloves and safety glasses) when working on or near chemical metering pumps.

3. Tampering with electrical devices can be potentially hazardous. Always place chemicals and feeder installation well out of the reach of children and others.

4. Be careful to check that the voltage of the installation matches the voltage indicated on the specification label. Each pump is equipped with a three prong plug. Whether plugging into a receptacle or wiring into a system, always be sure the feeder is grounded. If receptacle is utilized, to disconnect, do not pull wire but grip the plug with fingers and pull out.

5. Never repair or move the metering pump while operating. Always disconnect electrical current. Before handling the pump always allow sufficient time for the motor housing to cool off. Handling the pump too soon after shutdown may cause hand burns. For safety use protective gloves.

6. All pumps are pretested with water before shipment. Remove head and dry thoroughly if you are pumping a material that will react with water, (e.g. sulfuric acid). Valve seats, ball checks, gaskets, and diaphragm should also be dried. Before placing feeder into service, extreme care should be taken to follow this procedure.

7. Arrows on the pump head and injection fitting indicate chemical flow. When properly installed, these arrows should be pointing upward.

8. When metering hazardous material DO NOT use plastic tubing. Strictly use proper rigid pipe. Consult supplier for special adaptors.

9. Pump is NOT to be used to handle or meter flammable liquids or materials.

10. Standard white polyethylene discharge tubing is not recommended for installations exposed to direct sunlight. Consult supplier for special black polyethylene tubing.

11. Manufacturer will not be held responsible for improper installation of pumps, or local plumbing conducted. All cautions are to be read thoroughly prior to hook-up and plumbing. For all installations a professional plumber should be consulted. Always adhere to local plumbing codes and requirements.

12. Note the maximum pressure rating of the metering pump. When used with pressurized systems, always be sure the pressure of the system does not exceed maximum pressure rating listed on the specification label.

13. Be sure to depressurize system prior to hook-up or disconnection of metering pump.

INSTALLATION, PIPING AND WIRING

UNPACKING, ASSEMBLING AND MOUNTING:

The carton should contain:

 Metering Pump  4 ft. (1.21 m) Clear Flexible Suction Tubing  4 ft (1.21 m) Stiff White Return Tubing  Feeder can be mounted on a wall shelf bracket

(Figure B), tank stand platform (Figure C), directly on the wall (Figure D), or directly on the tank cover (Figure E).

 Bleed Valve Assembly  Instructions  Strainer Assembly w/Tube Weight  Back Check Valve Assembly  8 ft (2.43 m) Stiff White Discharge Tubing

(Optional black tubing for UV protection available from the factory)

To mount the feeder directly on the wall, place the feeder base against the wall with the motor below the pumping head, remove four head mounting bolts, and turn head quarter turn so suction is in bottom position.

IMPORTANT: Injection point must be higher than top of solution tank to prohibit gravity feeding. Maximum head in meters is 70m/H2O for Series 100 Model pumps and 42m/H2O for Series 150 Model pumps.

NOTE: Make sure the arrow on the outside of the pump head is pointing upward. The pump must be positioned so that the plug is accessible.

+ 8 hidden pages