Puls SL40.301, SL40.300 Data Sheet

Clever Power

SL40.300/.301

scheme

IEC60950

• Input: 3 AC 400...500V

• Output: 24...28V / 960W (1080W)

• No switch-off at overload

• Ideal for parallel operation

• Output for measurement and

logical signals (.301)

Data sheet

Input

Input voltage 3 AC 400...500 V, – 15 %, + 15 %

47-63 Hz, Suitable for IT power systems

Rated Tolerances

• Continuous operat.

• Short term (1 min) at 24 V/40 A

Input current 3.0 A

Inrush current < 30 A

Inrush current limiting done with a fixed 23R resistor (not a thermistor) which is bridged after the unit is running, so losses are minimized. That means no reset time even at a warm-start.

Fuse loading 3 A

To be fused with a 3 x 10A, B-type 'circuit-breaker' switch based on the usual thermomagnetic overload sensing principle (used anyway to fuse the input lines; unit has no internal fuses).

Harmonic current emissions (PFC)

Transient handling

Hold up time min. 15 ms

340-575 V AC 300-620 V AC

acc. EN 61000-3-2

Active transient filter incorporated, so transient resistance acc.to VDE 0160 / W2 (1300 V /

1.3 ms), for all load conditions.

at 400 V AC, 24 V / 40 A

Construction / Mechanics *

Housing dimensions and Weight

•W x H x D

• Free space for ventilation

•Weight

Connections (input and output)

Design advantages:

• All connection blocks mounted on front panel for ease of access.

• PVC insulated cable can be used for all connections, as the connection blocks are mounted in the cooler area on the underside of the unit.

• Power density: 230 W per litre housing volume.

275 mm x 124 mm x 117 mm (+ DIN rail) above/below each 70 mm recommended

left/right each 25 mm recommended

3.3kg

robust screw terminals, connector size range:

• solid: 1.5...6 mm

• flexible: 1.5...4 mm Output: Minus terminal with 2 connectors, current handling per output: 40 A (max. acc. to UL) resp. 56 A (max. acc. to VDE)

(Outp.: 0.5...16 mm2)

(Outp.: 0.5...10 mm2)

UL508 LISTED IND. CONT. EQ.

18 WM, 60°C

UL60950 E137006

CUL/CSA-C22.2

No 950-M90

EMC and Low Volt. Directive

Output (signal outputs see overleaf)

Output voltage 24...28 V DC, adjustable by (covered) front

Output noise suppression

Ambient temperature range T

amb

Rated continuous loading with convection cooling

•T

=0°C - 60°C

amb

•T

=0°C - 45°C

amb

Derating typ. 24 W/K (at T

Voltage regulation better than 2% over all

Ripple (incl. spikes) < 50 mV

Over-voltage protectionAt 32 V ± 10%: switch to hiccup mode

Front panel indicators: • Green LED on, when V

Parallel operation SL40.300: yes, no active current sharing

Current sharing by balancing line (active sharing principle, SL40.301) or ’soft’ output characteristic (passive sharing principle, SL40.300; characteristic switch-over by jumper as in SL20/SL30 without opening the unit)

Power Back Immunity < 35 V

panel potentiometer. Adj. range guaranteed

Radiated EMI values below EN 61000-6-3, even when using long, unscreened output cables.

Operation: 0°C...+70°C (>60°C: Derating) Storage: -25°C...+85°C

24 V / 40 A (960 W) resp. 28 V / 35 A (980 W) 24 V / 45 A (1080 W) resp. 28 V / 38 A (1064 W) short-term (< 1 min.) also at 60°C admissible

=+60°C...+70°C)

amb

(20 MHz bandw., 50 Ω measurem.)

> UT, where UT is

out

< U

ca. 2 V below Vout adjusted (24V...28V)

• Red LED on, when V

SL40.301: yes, active current sharing, please refer to “Output Signaling” - “Current Balance”

Efficiency, Reliability etc. *

Efficiency typ. 92.5% (400 VAC, 24 V / 40 A)

Losses typ 78 W (400 VAC, 24 V / 40 A)

MTBF SL40.300: 305,000 h SL40.301: 268,000 h

acc. to Siemensnorm SN 29500 (24 V/40 A, 400 VAC, T

Life cycle (electrolytics) The unit exclusively uses longlife electrolytics,

specified for +105°C (cf. ’The SilverLine’, p.2). High reliability and lifetime, as

• only 6 aluminum electrolytics and

• no small aluminum electrolytics are used.

= +40 °C)

amb

Order information

Order number Description

SL40.300 SL40.301 SLZ01

sl40e300 / 040211 1/2

basic version, passive load sharing with signal/measurement outputs, signal output connector included: Order number XFB-S-W8-MSTB 06-W8) Screw mounting set, two needed per unit

Data sheet

Start / Overload Behaviour

Startup delay < 0.5 s

Rise time < 0.1 s (40 A, 20,000 µF)

Overload behaviour PULS Overload Design (see diagram at the right), thus neither

switch-off nor hiccup at overload

Advantages:

• High short-circuit current, giving large ’start-up window’: unit starts reliably even with awkward loads (DC-DC converters, motors). No ’sticking’ as can occur with fold-back characteristics.

• Even longer overload possible as unit does not switch off.

Output for measurements and signalling

(SL40.301 only)

’Shut-Down’: Shut-down input: units switches off, if

• Input is connected to ’Signal GND’ (∆U < 1V) or

• +20...28 V Voltage are applied to this input and ’Signal GND’ (max. 20 mA).

’Power Good’: Power-Fail / -Good

• Signal: High (24 V) at correct operation (no overload, over-temp., short-circuit). At ’low’ signal and nominal load, output remains at nominal voltage for at least 5 ms.

• Corresponding ground is ’Signal GND’ output (current source)

• Permissable load resistance: ≥ 300 Ω, e.g. 24V relais, control lamp (no dropping resistor needed for LED), scoring logic. To get 5V level: connect this output and ’Signal GND’ via 5V zener diode (0.5W) + 1kΩ resistor switched in parallel

’Thermal Alarm’: warning signal at over-temperature

• Signal: High (24 V) at correct operation (no over-temperature). If signal switches to ’low’ and temperature increases further, output current is lowered,

• Ground and permissable load resistance: see ’Power Good’ output

’Current Monitor’: Current measurement output, usable with

• Voltmeter

• Ammeter

’Current Balance’: balancing output for current sharing

• For active current sharing at parallel operation interconnect the "Current Balance" output terminals of all paralleled units. The corresponding ground is the

pole. Do not interconnect the "Signal GND" outputs. Exact output voltage re-

gulation is effective when the output current is greater than 0.4A. Current sharing also works reliable with decoupling diodes and modules for redundancy applications.

’Signal GND’: Ground terminal for all signal outputs of this unit (not ’Current Balance’)

• Do not connect this terminal to the of overload)

• Do not connect this terminal to any output of another unit (not even with ’Signal GND’ of another unit)

• max. load current: 0.3 A Signal ground is internally fused by a self-curing fuse (polyswitch)

1 V per 10 A output current (to ’Signal GND’ output, R meter) > 100 kΩ) 1 mA per 10 A output current (to ’Signal GND’ output, R meter) < 100 Ω)

terminal of this unit (not even across a load: risk

(volt-

(am-

Further Information

Output V/I characteristic (typ.)

Output voltage Vout [V]

Efficiency (typ., at V

94%

92%

90%

88%

Efficiency [%]

86%

84%

82%

Hold-up time (min., at V

Hold-up time [ms]

SL40.300:

Vout= 24V, S ingle Mode

Vout= 24V, P arallel Mode

Vout= 28V, S ingle Mode

Vout= 28V, P arallel Mode

SL40.301: no s witc h-over, charact . as S L40.300, S ingle Mode

0 1020304050

Output current Iout [A]

=24V)

out

3 x 340 VA Cin 3 x 400 VA Cin 3 x 480 VA Cin

5 10152025 30354045

Output current Iout [A]

=24V)

out

Iout = 16 A Iout = 24 A Iout = 32 A Iout = 40 A Iout = 45 A

For further information, especially about EMC, Connections, Safety, Approvals, Mechanics und Mounting see page 2 of the „The SilverLine“ data sheet. For detailed dimensions please see the SilverLine mechanics data sheet SL40.

Specifications valid for 3 x AC 400V input voltage, +25°C ambient temperature, and 5 min run-in time, unless otherwise stated. They are subject to change without prior notice.

Your partner in power supply:

340 380 420 460 500

Input voltage Vin [V ]

European Power Supply Manufacturers Association

Bayerns Best 50 Czech 100 Best EuropeÕs 500

PULS GmbH

Arabellastraße 15

D-81925 München

Tel.: +49 89 9278-0

Fax: +49 89 9278-199

www.puls-power.com

2/2 sl40e300 / 040211