Puls SL20.113 Data Sheet

SL20 with 48...56V

SL20.113

scheme

IEC60950

UL508 LISTED IND. CONT. EQ.

18 WM, 60°C

• Input: AC 115/230V auto select

• Output: 48...56V / 480W

• 93% Efficiency

• Ideal for parallel operation

Data sheet

Datasheet

Input

Input voltage AC 100-120V/220-240V,

47-63Hz, auto select

Rated tolerances

• Continuous

• Short-term (30s) at 48V/10A

Input current I

Inrush current limiting with active bypass of the limiting resistor (NTC).

Inrush current I

Fuse loading I²t <5A

To be fused with a 16A, B-type 'circuit-breaker' switch based on the usual thermomagnetic overload sensing principle (used anyway to fuse the input lines).

Transient handling Transient resistance acc. to VDE 0160 / W2

Hold-up time 30ms at 48V/10A, AC 230V

AC 85...132V or AC 184...264V AC 85...140V or AC 175...280V

<12A (115V range) <6A (230V range)

<18A @ AC 264V (T <37A @ AC 264V (T

s (T

= +25°C, cold start)

amb

<8A

s (T

= +50°C, cold start)

amb

(750V / 1.3ms), for all load conditions.

35ms at 48V/10A, AC 120V 15ms at 48V/10A, AC 100V

= +25°C, cold start)

amb

= +50°C, cold start)

amb

Efficiency, Reliability etc.*

Efficiency typ. 93% (AC 230V, 48V/10A)

Losses typ. 36.2W (AC 230V, 48V/10A)

MTBF 519.000h acc. to Siemensnorm SN29500

(48V/10A, 230V, T

Life cycle (electrolytics) The unit exclusively uses longlife electrolytics,

specified for +105°C (cf. ’The SilverLine’, p.2). High reliability, as

• only five aluminium electrolytics and

• no small aluminium electrolytics are used.

* For further information see data sheets„The SilverLine“,

„SilverLine Family Branches“ and mechanics data sheet SL20

Order information

amb

= 40°C)

UL60950 E137006

CUL/CSA-C22.2

No 60950

Type approval

acc. to:

• IEC / EN60950

• EN50178 Overvolt. cat. III

• EN60204

EMC and

Low Volt.

Directive

Output

Output voltage DC 48...56V, adjustable by (covered) front pan-

el potentiometer; preset: 48V ±0.5% Adjustment range guaranteed

Output noise suppression

Ambient temperature range T

amb

Rated continuous loading with convection cooling:

•T

=0°C - 60°C

amb

short-term (<30s)

Derating 12W/K (at T

Voltage regulation better 2% over all

Ripple

• Output charact. S

• Output charact. P

(S/P: Single/Parallel Mode)

Over-voltage protection At 58.6V ± 2.3%: switch to hiccup mode

Front panel indicators:

• Green LED on, when V

• Red LED on, when V

Parallel operation Yes, up to ten SL20

To achieve current sharing the output V/I characteristic can be altered to be 'softer' (47.9V at 0A, 45.6V at 10A). This is done by repositioning an external bridge connection (without opening the unit).

Power Back Immunity max. 57V

Radiated EMI values below EN50081-1, even when using long, unscreened output cables.

Operation: 0°C...+70°C (> 60°C: Derating) Storage: -25°C...+85°C

48V/10A resp. 56V/8.6A 48V/12.5A resp. 56V/10.7A

= 60-70°C)

amb

incl. spikes (20MHz bandw.), 50Ω measurem. <40mV <80mV <100mV

out

(<0.09%)

(In: AC 230V, Out: 48V/10A)

(In: AC 184V, Out: 56V/8.6A)

= V

out

adjusted

out

< V

Construction/ Mechanics*

Housing dimensions and Weight

•W x H x D

• Free space for ventilation

•Weight

Design advantages:

• All connection blocks are easy to reach as mounted on the front panel.

• PVC insulated cable can be used for all connections, as the connection blocks are mounted in the cooler area on the underside of the unit.

220mm x 124mm x 102mm (+ DIN rail) above/below 70mm recommended left/right 25mm recommended

1.8kg

Order number Description

SL20.113 SLZ02

sl20e113 / 040114 1/2

(wall mounting set; contains 2 pcs.)

Data sheet

Start / Overload Behaviour

Start-up delay typ. 0.55s

Rise time appr. 20-80ms, depending on load

Overload behaviour Puls Overload Design (see right-hand diagram)

Advantages:

• No disconnection/hiccup, thus overloading is possible also for a longer period of time (load start-up), ideal for parallel operation.

• High overload/short-circuit current due to straight characteristic; each bias point of the V/I characteristic extends 10A.

• Advantage: Due to the high and continuously supplied overload current the unit starts reliably even with awkward loads (DC-DC converters, motors). No 'sticking' can occur as, for example, with fold-back characteristics, and secondary fuses trigger more reliably.

Further information

Further information, especially about

•EMC

• Connections

• Safety, Approvals

• Mechanics and Mounting,

see page 2 of the „The SilverLine“ data sheet

For detailed dimensions

see SilverLine mechanics data sheet SL20

Output characteristic (typ.)

60 56 52 48 44 40 36 32 28 24 20 16

Outupt voltage Vout [V]

8 4 0

0 5 10 15 20

Efficiency (typ., at V

Efficiency [%]

48V Single 56V Single 48V Parallel 56V Parallel

Output current Iout [ A]

=48V)

out

100VAC 120VAC 230VAC

2468101214

Hold-up time (min., at V

Hold-up time [ms]

180 190 200 210 220 230 240

Unless otherwise stated, specifications are valid for AC 230V input voltage, +25°C ambient temperature, and 5 min. run-in time. They are subject to change without prior notice.

60% Load 100% Load 125% Load

=48V)

out

Input voltage VACin [V]

at AC 230V

90 80 70 60 50 40 30 20

Hold-up time [ms]

85 90 95 100 105 110 115 120 125 130

60% Load 100% Load 125% Load

Input voltage VACin [V]

Your partner in power supply:

Output current Iout [A]

at AC 115V

European

Power Supply

Manufacturers

Association

Bayerns Best 50

Czech 100 Best

Europe’s 500

PULS GmbH

Arabellastraße 15

D-81925 München

Tel.: +49 89 9278-0

Fax: +49 89 9278-199

www.puls-power.com

2/2 sl20e113 / 040114