Puls ML100.200 Data Sheet

MiniLine

GENERAL DESCRIPTION

The ML100.200 is a simple and cost effective approach to convert the AC voltage of a typical three phase system into a regulated DC voltage. It only requires two phases and thereby saves terminal space, terminal cost, wires, fuses and installation time.

The ML100.200 is very compact, high efficient and easy to use. The input is internally protected, which makes external fuses unnecessary in many cases.

Weighing only 360g, it is a lightweight compared to the 50/60Hz control transformers, which are commonly used for low-power control voltages where a neutral wire is not available.

High immunity to transients and power surges as well as low electromagnetic emission makes usage in nearly every environment possible.

2428V

- -

+ +

ML100.200

24V 4.2A, TWO-PHASE INPUT

POWER SUPPLY

■ 2AC 380-480V

■ 2 Phase Input

■ No Neutral Wire Required

■ Input Fuse Included

■ Efficiency up to 90.0%

■ Full Output Power Between -10°C and +60°C

■ Quick-connect Spring-clamp Terminals

■ 3 Year Warranty

SHORT-FORM DATA

Output voltage DC 24V Adjustment range 24-28V guaranteed Output current 4.2-3.6A Output power 100W Output ripple < 50mVpp 20Hz to 20MHz

Input voltage 2AC 380-480V ±15% Mains frequency 50-60Hz ±6% AC Input current typ. 0.46 / 0.4A at 400 / 480Vac Power factor typ. 0.6 / 0.55 at 400 / 480Vac AC Inrush current typ. 36 / 45A at 400 / 480Vac Hold-up time typ. 48 / 85ms at 400 / 480Vac DC Input consult PULS Efficiency 89.5 / 89.0% at 400 / 480Vac Losses 11.7 / 12.3W at 400 / 480Vac Temperature range -10°C to +70°C operational

-40°C to +85°C storage, transport Derating 2.5 W/°C +60 to +70°C Humidity < 95% r.H. IEC 60068-2-30

Do not energize while condensation is present

Vibration Shock

Dimensions 72.5x75x103mm WxHxD

2g (2 hours/axis) IEC 60068-2-6 30g 6ms,

IEC 60068-2-27

20g 11ms

ORDER NUMBERS

Power Supply

ML100.200

Accessory MLY02.100 Decoupling Module

ML100.200 Rev 1.0-EN / All parameters are specified at 24V, 4.2A, 400Vac and 25°C ambient unless otherwise noted.

24-28V Power Supply

www.pulspower.com Phone +49 89 9278 0 Germany

MARKINGS

18WM

LISTED

IND. CONT. EQ.

UL 508

UL 60950-1,

EMC, LVD

1/2

MiniLine

OUTPUT

Output voltage nom DC 24V Adjustment range min 24V-28V Factory set typ 24.5V Output current nom 4.2A at 24V, 3.6A at 28V Line regulation max 20mV 323…552Vac Load regulation max 240mV static regulation Serial use allowed Parallel use allowed Return voltage max 35V OVP typ 34V max 39V

Output voltage vs. output current, typ.

Output Voltage

28V

4 0

024

Output current vs. ambient temperature

Allowable Output Current at 24V

-10 0 20 40

Ambient temp. is defined 2cm below the unit

Output Current

Ambient Temperature

Adjustment

Range

8A531 67

70°C

ML100.200

24V 4.2A, TWO-PHASE INPUT

TERMINALS AND WIRING

Type Bi-stable, quick-connect spring clamp

Solid wire 0.3-2.5mm2 Stranded wire 0.3-2.5mm2 AWG AWG 26-12 Stripping length 6mm / 0.25inch Ferrules allowed, but not required

EMC

EMC Immunity EN 61000-6-1, EN 61000-6-2 EMC Emission EN61000-6-3, EN 61000-6-4 EN 55011, EN 55022, FCC-15 Harmonic input current EN61000-3-2 (PFC) Flicker EN61000-3-3

APPROVALS

UL 508 Industrial Control Equipment UL 60950-1 Information Technology Equipment

FULFILLED STANDARDS

EN 61558-2-17 Safety of Power Transformers EN/IEC 60204-1 Safety of Electrical Equip. of Machines EN/IEC 60950-1 Information Technology Equipment EN/IEC 61131-2 Programmable Controllers EN 50178 Electronic Equip. Power Installations

DIMENSIONS AND WEIGHT

terminals. Shipped in open position.

SAFETY AND PROTECTION

Input / output insulation SELV IEC/EN 60950-1 PELV EN 60204-1 3000Vac 2s type test Degree of pollution 2 EN 50178 Degree of protection IP 20 EN/IEC 60529 Class of protection I PE required Over-voltage category III EN 50178

Internal input fuse T3A15

in L1, not accessible

Temperature protection not included

Use 35mm DIN-rails according to EN 60715 or EN 50022 with a height of 7.5 or 15mm. The DIN-rail height must be added to the depth (103mm) to calculate the total required installation depth.

Weight max 360g 0.79lb

The power supply shall only be installed and put into operation by qualified personnel. This power supply is designed for installation in an enclosure and is intended for the general use, such as in industrial control, office, communication, and instrumentation equipment. Do not use this device in aircraft, trains and nuclear equipment, where malfunctioning of the power supply may cause severe personal injury or threaten human life. The information presented in this document is believed to be accurate and reliable and may change without notice.

ML100.200 Rev 1.0-EN / All parameters are specified at 24V, 4.2A, 400Vac and 25°C ambient unless otherwise noted.

www.pulspower.com Phone +49 89 9278 0 Germany

2/2