VGA/Stereo Audio Selection Switcher 16x1
PTN Electronics Limited www.PTN-electronics.com
WVG16A
PTN VGA/Stereo Audio Selection Switcher 16x1
USER MANUAL
Version: WVG16A2013V1.1
VGA/Stereo Audio Selection Switcher 16x1
PTN Electronics Limited www.PTN-electronics.com
NOTICE: Please read this user manual carefully before using this product.
Update History
Version
Date
Update Content
1.0
2013.01.06
First version.
1.1
2013.05.24
Modified the system diagram.
This manual is only an instruction for operators, not for any maintenance usage.
The functions described in this version are updated till May 2013. Any changes of
functions and parameters since then will be informed separately. Please refer to the
dealers for the latest details.
This manual is copyright PTN Electronics Limited. All rights reserved. No part of
this publication may be copied or reproduced without the prior written consent of
PTN Electronics Limited.
All product function is valid till 2013-05-24.
VGA/Stereo Audio Selection Switcher 16x1
PTN Electronics Limited www.PTN-electronics.com
Table of Contents
1. Introduction ............................................................................................................... 1
1.1. Introduction to WVG16A ................................................................................ 1
1.2. Package Contents ......................................................................................... 1
2. Features .................................................................................................................... 1
3. Specification .............................................................................................................. 1
4. Operations of the Control Panel and the IR Remote ................................................. 3
4.1. Operations of the Control Panel ..................................................................... 3
4.2. Usage of the IR Remote ................................................................................ 4
5. System Connection ................................................................................................... 4
5.1. Interface Connection ...................................................................................... 4
5.2. Connection with Control System .................................................................... 5
5.3. Connection with Computer............................................................................. 5
6. System Diagram ........................................................................................................ 6
7. Communication Protocol and Command Codes ....................................................... 6
8. Troubleshooting & Maintenance ................................................................................ 8
9. Safety Operation Guide ............................................................................................. 8
10. After-sales Service .................................................................................................... 9
VGA/Stereo Audio Selection Switcher 16x1
PTN Electronics Limited 1 www.PTN-electronics.com
1. Introduction
1.1. Introduction to WVG16A
WVG16A is a 16x1 selection switcher for VGA & stereo audio. It supports auto-switching
and has a bandwidth up to 3200*2400@60MHz. It’s a high performance device for
conference room, educational facility, multi-media meeting room, demonstration hall etc.
1.2. Package Contents
1 x WVG16A
1 x Power Cord
1 x IR remote
1 x RS232 cable
4 x Plastic cushions
1 x User Manual
Notes: Please confirm if the product and the accessories are all included, if not, please
contact with the dealers.
2. Features
Super bandwidth at 1GHz
Support resolution up to 3200*2400@60MHz.
Ultra-switching for instaneous display.
Built-in gain compensation and sync signal proofread technology
Controllable via button, IR remote & RS232.
3. Specification
Video Input
Video Output
Input
16 VGA
Output
1 VGA
Input Connector
VGA (15 pin HD),
female
Output Connector
VGA (15 pin HD),
female
Video Signal
RGBHV, RGBS,
RGsB, RsGsBs,
component video,
S-video, composite
video
Video Signal
RGBHV, RGBS,
RGsB, RsGsBs,
component video,
S-video, composite
video
Video General
Resolution
Range
3200x2400@60Hz(3dB)
0~10MHz is +0.1dB
to -0.1dB
0~130MHz is +6dB
to -0.8dB
Bandwidth
1GHz (-3dB) full
loading
Return Loss
-30dB@5MHz
Crosstalk
-50dB@5MHz
VGA/Stereo Audio Selection Switcher 16x1
PTN Electronics Limited 2 www.PTN-electronics.com
Switching Speed
200ns (Max.)
Input/Output Level
0.5Vp-p ~ 2.0Vp-p
Gain
0dB
I/O Impedance
75Ω
Audio Input
Audio Output
Input
16 stereo audio
Output
1 stereo audio
Input Connector
3.5mm mini jack
connector
Output Connector
3.5mm mini jack
connector
Audio Input
Impedance
>10KΩ
Audio Output
Impedance
50Ω
Switching Speed
200ns (Max.)
Output Volume
61 degree
controllable(0~61)
Output Bass
15 degree
controllable(-7~+7)
Output Treble
15 degree
controllable (-7~+7)
Audio General
Frequency
Response
20Hz~20KHz
Stereo Channel
Separation
>80dB@1KHz
CMRR
>90dB @20Hz to
20K Hz
Switching Soltuion
Audio break away
switching
Control Parts
Control/Remote
Buttons, IR remote
& RS232 (9-pin
female D connector)
Pin Configurations
2 = TX, 3 = RX, 5 =
GND
General
Max DC
compensation
1.5V
Humidity
10% ~ 90%
Temperature
-20 ~ +70℃
Power
Consumption
20W
Power Supply
100VAC ~ 240VAC,
50/60Hz
Product Weight
3.2Kg
Case Dimension
W483 x H87x D260mm(2U high)
NOTE: All nominal levels are at ±10%.
VGA/Stereo Audio Selection Switcher 16x1
PTN Electronics Limited 3 www.PTN-electronics.com
4. Operations of the Control Panel and the IR Remote
4.1. Operations of the Control Panel
No.
Name
Description
①
INPUTS
Input channel selection buttons, from 1 to 16. 16 channels in
total.
②
MENU
Function buttons.
③
, IR
Power indicator, turn red when power on. IR is the infrared
receiver.
Description of the buttons:
Buttons
Function Description
…
Input buttons. It is the number of every input channel (16 in
total), from left to right is 1, 2, 3…16.
AV synchronal button: To transfer video and audio signal
synchronously by the switcher.
Example: To transfer both the video and the audio signals
from input channel No.3 to output channel No.4.
Operation: Press buttons in this order“3”, “AV”.
Video button: To transfer only video signals from input
channel to output channel
Example: To transfer video signals from input channel No.3
to output channel No.4.
Operation: Press buttons in this order“3”, “VIDEO”.
Audio button: To transfer only audio signals from input
channel to output channel
Example: To transfer audio signals from input channel No.2
to output channel No.3.
Operation: Press buttons in this order “2”, “AUDIO”.
AUDIO
VIDEO
AV
16 2 1
① ② ③
VGA/Stereo Audio Selection Switcher 16x1
PTN Electronics Limited 4 www.PTN-electronics.com
4.2. Usage of the IR Remote
When use the IR remote, please press the buttons in this order:
”Input Channel” +”Menu”
1) Input Channel: Select one input channel.
2) Menu: Include AV, VIDEO & AUDIO.
5. System Connection
5.1. Interface Connection
No.
Name
Description
①
AUDIO INPUTS
Audio input channels, 16 in total. 3.5mm mini jack.
②
AUDIO OUTPUT
Audio output channel. 3.5mm mini jack.
③
VGA INPUTS
VGA input channels, 16 in total. Female 15 pin HD
connector.
④
VGA OUTPUT
VGA output channel. Female 15 pin HD connector.
① ②
③ ④ ⑤ ⑥
VGA/Stereo Audio Selection Switcher 16x1
PTN Electronics Limited 5 www.PTN-electronics.com
⑤
RS232
Serial control port, 9-pin female connector.
⑥
AC100V~240V
Alternating current for power supply.
5.2. Connection with Control System
With the RS232 port, the switchers can be control by several kinds of control systems.
This RS232 communication port is a female 9-pin D connector. The definition of its
pins is as the table below.
No. Pin Function
1 N/u Unused
2 Tx Transmit
3 Rx Receive
4 N/u Unused
5 Gnd Ground
6 N/u Unused
7 N/u Unused
8 N/u Unused
9 N/u Unused
5.3. Connection with Computer
Please connect reference to the following contents.
1) Use a RS232 control line to connect the COM1 or COM2 port of the computer to
the RS232 interface of WVG16A.
2) Install the serial driver.
3) Run the COM software and check the connecting state.
4) If it’s OK, then we can control WVG16A by sending RS232 command codes. If not,
probably the control line is bad contact.
VGA/Stereo Audio Selection Switcher 16x1
PTN Electronics Limited 6 www.PTN-electronics.com
6. System Diagram
7. Communication Protocol and Command Codes
Communication protocol: RS232 Controlling Protocol Command Type: ASCII
Baud rate: 9600 Date bit: 8 Stop bit: 1 Parity bit: none
Command
Types
Command
Codes
Functions
System Command
/*Type;
Inquire the models information.
/%Lock;
Lock the keyboard of the control panel on the Matrix.
/%Unlock;
Unlock the keyboard of the control panel on the Matrix.
/^Version;
Inquire the version of firmware
/:Message
Off;
Turn off the feedback command from the com port. It
will only show the “switcher OK”.
/:Message
On;
Turn on the feedback command from the com port.
Undo.
To cancel the previous operation.
Demo.
Switch to the “demo” mode, 1->1, 2->2, 3->3 … and so
on.
[x1]#.
Transfer signals from the input channel [x1] to the
output channel [x1].
VGA/Stereo Audio Selection Switcher 16x1
PTN Electronics Limited 7 www.PTN-electronics.com
[x1]$.
Switch off the output channel [x1].
Operation Command （PUTRON2.0 Command System）
[x1] V[x2].
Transfer the video signals from the input channel [x1]
to the output channel [x2].
[x1]
V[x2],[x3],[
x4].
Transfer the video signals from the input channel [x1]
to the output channels [x2], [x3] and [x4].
[x1] A[x2].
Transfer the audio signals from the input channel [x1]
to the output channel [x2].
[x1]
A[x2],[x3],[
x4].
Transfer the audio signals from the input channel [x1]
to the output channels [x2], [x3] and [x4].
[x1] B[x2].
Transfer both the video and the audio signals from the
input channel [x1] to the output channel [x2].
[x1]
B[x2],[x3],[
x4].
Transfer both the video and the audio signals from the
input channel [x1] to the output channels [x2], [x3] and
[x4].
Status[x1].
Inquire the input channel to the output channel [x1].
Status.
Inquire the input channel to the output channels one by
one.
Save[Y].
Save the present operation to the preset command [Y].
[Y] ranges from 0 to 9.
Recall[Y].
Recall the preset command [Y].
Clear[Y].
Clear the preset command [Y].
Note:
1) [x1], [x2], [x3] and [x4] are the symbols of input or output channels ranged according
to the model of the matrix switcher. If the symbols exceed the effective range, it
would be taken as a wrong command.
2) In above commands, “[”and “]” are symbols for easy reading and do not need to be
typed in actual operation.
3) Please remember to end the commands with the ending symbols “.” and “;”.
VGA/Stereo Audio Selection Switcher 16x1
PTN Electronics Limited 8 www.PTN-electronics.com
8. Troubleshooting & Maintenance
1) When there is no output images/sounds:
Check if there is any signal at the input.
Check if there is any signal at the output.
We can check these by using an oscilloscope or a multimeter. If there is no signal
input/output, maybe the input/output cables broken or the connectors loosen, please
change for another cable.
Make sure the destination device is exactly on the controlled output channel.
If not the problem mentioned above, probably there is something broken inside the
unit, please send it to the dealer for repairing.
2) If the POWER indicator doesn’t work or no respond to any operation, please make
sure the power cord connection is good.
3) If the output image/sound is interfered, please make sure the system is grounded
well.
4) If the static becomes stronger when connecting the video/audio cables, it probably
due to the incorrect grounding, please correct it.
5) If the switcher cannot be controlled by the buttons, IR remote or the RS232 port, the
switcher may have broken. Please send it to the dealer for repairing.
9. Safety Operation Guide
In order to guarantee the reliable operation of the equipments and safety of the staff,
please abide by the following proceeding in installation, using and maintenance:
1) The system must be earthed properly. Please do not use two blades plugs and
ensure the alternating power supply ranged from 100v to 240v and from 50Hz to
60Hz.
2) Do not put the switcher in a place of too hot or too cold.
3) As the power generating heat when running, the working environment should be
maintained fine ventilation, in case of damage caused by overheat.
4) Cut off the general power switch in humid weather or left unused for long time.
5) Before following operation, ensure that the alternating current power is off:
Take off or reship any components of the equipment.
Take off or rejoin any pin or other link of the equipment.
6) As to non-professional or without permission, please DO NOT try to open the casing
of the equipment, DO NOT repair it on your own, in case of accident or increasing
the damage of the equipment.
7) DO NOT splash any chemistry substance or liquid in the equipment or around.
VGA/Stereo Audio Selection Switcher 16x1
PTN Electronics Limited 9 www.PTN-electronics.com
10. After-sales Service
1) If there appear some problems when running WVG16A, please check and deal with
the problems reference to this user manual. Any transport costs are borne by the
users during the warranty.
2) You can email to our after-sales department or make a call, please tell us the
following information about your cases.
Product version and name.
Detailed failure situations.
The formation of the cases.
3) We offer products for all three-year warranty, which starts from the first day you buy
this product (The purchase invoice shall prevail).
4) Any problem is same with one of the following cases listed, we will not offer warranty
service but offer for charge.
Beyond the warranty.
Damage due to incorrectly usage, keeping or repairing.
Damage due to device assembly operations by the maintenance company
non-assigned.
No certificate or invoice as the proof of warranty.
The product model showed on the warranty card does not match with the model
of the product for repairing or had been altered.
Damage caused by force majeure.
Remarks: For any questions or problems, please try to get help from your local
distributor, or email PTN at: support@PTN-electronics.com.
Loading...