Page 1
www.PTN-electronics.com
MMX6464
PTN Modular Matrix Switcher 64x64
All Rights Reserved
Version: MMX6464_2015V2.2
User Manual
Page 2
Modular Matrix Switcher 64x64
PTN Electronics Limited www.PTN-electronics.com
Preface
Read this user manual carefully before using this product. Pictures shown in this
manual is for reference only, different model and specifications are subject to real
product.
This manual is only for operation instruction only, not for any maintenance usage. The
functions described in this version are updated till March 2015. Any changes of
functions and parameters since then will be informed separately. Please refer to the
dealers for the latest details.
All product function is valid till 2015-3-13.
Trademarks
Product model, PTN and its logo are trademarks of PTN Electronics Limited.
Any other trademarks mentioned in this manual are ac knowledged as the properties of
the trademark owner. No part of this publication may be copied or reproduced without
the prior written consent of PTN Electronics Limited.
FCC Statement
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accorda nce with the ins tr uc tion s, may c ause har mful interference
to radio communications. It has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 1 5 of th e FCC R ules. These li mits are d esigne d
to provide reasonable protection against harmful interference in a commercial
installation.
Operation of this equipment in a residential area is likely to cause interference, in
which case the user at their own expense will be required to take whatever measures
may be necessary to correct the interference.
Any changes or modifications not expressly approved by the manufacture would void
the user’s authority to operate the equipment.
Page 3
Modular Matrix Switcher 64x64
PTN Electronics Limited www.PTN-electronics.com
SAFETY PRECAUTIONS
To insure the best from the product, please read all instructions carefully before us ing
the device. Save this manual for further reference.
Unpack the equipment carefully and save the original box and packing material for
possible future shipment
Follow basic safety precautions to reduce the risk of fire, electrical shock and injury
to persons.
Do not dismantle the housing or modi fy the module. It may result in electrical shock
or burn.
Using supplies or parts not meeting the products’ specifications may cause damage,
deterioration or malfunction.
Refer all servicing to qualified service personnel.
To prevent fire or s hoc k haz ar d, do not expose the unit to rai n, m ois tur e or i nstall this
product near water.
Do not put any heavy items on the extension cable in case of extrusion.
Do not remove the housing of the device as opening or removing housi ng may
expose you to dangerous voltage or other hazards.
Install the device in a place with fine ventilation to avoid damage caused by
overheat.
Keep the module away from liquids.
Spillage into the ho usi ng m ay resul t in f ir e, e lectr ic al s hoc k, or equipment damage. If
an object or liquid falls or spills on to the housing, unplug the module immediately.
Do not twist or pull by force ends of the optical cable. It can cause malfunction.
Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to
the device before cleaning.
Unplug the power cord when left unused for a long perio d of time.
Information on disposal for scrapped devices: do not burn or mix with general
household waste, please treat them as norm al ele ctri cal wastes.
Page 4
Modular Matrix Switcher 64x64
PTN Electronics Limited i www.PTN-electronics.com
Table of Contents
1. Introduction ................................................................................................................. 1
1.1. About MMX6464
............................................................................................... 1
1.2. Features ........................................................................................................... 1
1.2.1. MMX signal card (changeable cards)
..................................................... 1
1.4 Package List ...................................................................................................... 2
2. Panel D escript ion
........................................................................................................ 3
2.1. MMX6464 ......................................................................................................... 3
2.1.1. Front Panel
............................................................................................. 3
2.1.2. Rear Panel .............................................................................................. 4
2.2. Changeable Cards
............................................................................................ 5
2.2.1. 4I-DV & 4O-DV ....................................................................................... 5
2.2.2. 4I-DS& 4O-DS
........................................................................................ 6
2.2.3. 4I-HD & 4O-HD ....................................................................................... 6
2.2.4. 4I-VG & 4O-VG
....................................................................................... 7
2.2.5. 4I-VA ....................................................................................................... 8
2.2.6. 4I-SD & 4O-SD
....................................................................................... 9
2.2.7. 4I-TP & 4O-TP ........................................................................................ 9
2.2.8. 4I-UH & 4O-UH
..................................................................................... 10
2.2.9. 4I-UF & 4O-UF ..................................................................................... 11
2.2.10. 4I-BT & 4O-BT
.................................................................................... 11
3. System Connection ................................................................................................... 12
3.1. Usage Precautions
......................................................................................... 12
3.2. Connection Diagram ....................................................................................... 13
3.3. Application ...................................................................................................... 13
4. Control Operations .................................................................................................... 14
4.1. IR Remote control
........................................................................................... 15
4.2. RS232 Control ................................................................................................ 16
4.2.1. Connection of RS232 Communication Port
.......................................... 16
4.2.2. RS232 Communicat ion C omma nd s ..................................................... 16
4.3. TCP/IP Control (Optional)
............................................................................... 23
4.3.1. Control Modes ...................................................................................... 23
Page 5
Modular Matrix Switcher 64x64
PTN Electronics Limited ii www.PTN-electronics.com
4.3.2. TCP/IP Settings .................................................................................... 24
5. Specification ............................................................................................................. 25
5.1. Main Unit
........................................................................................................ 25
5.2. Changeable Cards .......................................................................................... 26
5.2.1. 4I-DV & 4O-DV
..................................................................................... 26
5.2.2. 4I-DS & 4O-DS ..................................................................................... 26
5.2.3. 4I-HD & 4O-HD
..................................................................................... 27
5.2.4. 4I-VG & 4O-VG ..................................................................................... 27
5.2.5. 4I-VA
..................................................................................................... 28
5.2.6. 4I-SD & 4O-SD ..................................................................................... 28
5.2.7. 4I-TP & 4O-TP
...................................................................................... 29
5.2.8. 4I-UH & 4O-UH ..................................................................................... 29
5.2.9. 4I-UF & 4O-UF
..................................................................................... 30
5.2.10. 4I-BT & 4O-BT .................................................................................... 31
6. Troubleshooting & Maintenance
............................................................................... 32
7. After-sales Service .................................................................................................... 34
Page 6
Modular Matrix Switcher 64x64
PTN Electronics Limited 1 www.PTN-electronics.com
1. Introduction
1.1. About MMX6464
MMX6464 is a high-performance video and audio modular matrix switc her supporting
max 64 i nput signal sources and 64 output display synchronously. It supports different
video signals wi th cross switching. Every video or audio signal is transmitted and
switched independently to decrease signal attenuation. MMX6464 supports various
changeable cards including HM DI, D VI, VG A, SDI and HDBaseT etc, and all the cards
support hot plug & play. Users can choose to insert di fferent signal card for different
application.
MMX6464 have power fail memory function and audio can break away from or follow
the video to switch. It has RS232 port for serial control and optional IP port for TCP/IP
control, can be easily controlled by third-part devices.
With its flexible design, MMX6464 can be used for different project and tend to be an
all-in-one solution. It is the com bo solution for multimedia conference rooms, control
rooms, broadcasting rooms, shopping center etc. It will handle all the audiovisual
management, including the switching, driving, scali ng etc.
1.2. Features
Modular chassis with configurable I/O slots, ranging from 4x4 to 64x64.
Various I/O cards, includes HDMI, HDBaseT, SD/HD/3G-SDI, DVI and VGA cards
(Compatible with YUV, YC & CVBS.) to configure any matrix.
Truly cross-point switching, any input to any output, regardless signal format.
Support HDMI1.4a, support 3D.
Integrated HDBaseT technology.
Controllable via button, RS232 & optional TCP/IP, also compatible with 3rd parties
control.
HDCP compliant.
LCD display.
1.2.1. MMX signal card (changeable cards)
To meet different situation and users, the MMX6464 cards are classified into the
following models:
Spec
Models
Inputs Signal Format
4I-HD 4 HDMI
4I-DV 4 DVI
4I-DS 4
DVI, HDMI, VGA, AV,
YPbPr
4I-VG 4 VGA
4I-VA 4 VGA& PCM audio
Input Cards
Page 7
Modular Matrix Switcher 64x64
PTN Electronics Limited 2 www.PTN-electronics.com
Spec
Models
Inputs Signal Format
4I-SD
4 inputs & 4 LO O P
outputs for each
channel)
SDI
4I-TP 4 HDMI TP, IR, RS232
4I-UH 4 HDMI& PCM Audio
4I-UF 4 Optical Fiber
4I-BT 4 HDBT, RS232, Audio
Spec
Models
Outputs Signal Format
4O-HD 4 HDMI
4O-DV 4 DVI
4O-DS 4
DVI, HDMI, VGA, AV,
YPbPr
4O-VG
4 VGA, 4 Stereo
audio
VGA, analog audio
4O-SD
4 outputs & 4
LOOP outputs for
each channel)
SDI
4O-TP
4
HDMI TP, IR, RS232
4O-UH 4 HDMI& PCM Audio
4O-UF 4 Optical Fiber
4O-BT 4 HDBT, RS232, Audio
1.4 Package List
1 x MMX6464
1 x RS232 cable
4 x Plastic cushions
1 x IR remote (The cell battery is not included)
1 x Power Cord
4 x Male VGA to female YPbPr cable (packed only when includes the 4I-VG/4I-VA
cards)
4 x Male VGA to female S-video & RCA (C-video) cable (packed only when
includes the 4I-VG/4I-VA cards)
1 x User manual
Notes: Please confirm if the product and the accessories are all included, if not,
please contact with the dealers.
Output Cards
Input Cards
Page 8
Modular Matrix Switcher 64x64
PTN Electronics Limited 3 www.PTN-electronics.com
2. Panel Description
2.1. MMX6464
2.1.1. Front Panel
Figure 2- 1 Front Panel of MMX6464
No.
Name
Description
①
IR
IR sensor, receive IR signal sent from IR remote
②
Power
indicator
Illuminate red once powered on
③
LCD
screen
Display real-time oper ati on sta tus
④ INPUTS
Buttons for input channels with green back-light indicating, ranges
from 0~ 9, 64 selectable channels in total.
⑤ OUTPUTS
Buttons for output channels with green back-light indicating,
ranges from 0 ~ 9, 64 selectable channels in total.
⑥ MENU
AV: transfer video and audio signal synchronously
‚: division button, to divide the output channels when swi tching to
more than one channel.
Page 9
Modular Matrix Switcher 64x64
PTN Electronics Limited 4 www.PTN-electronics.com
ENTER: confirm switching operation. O
peration will not be
executed by the matrix without confirmation.
ALL: To transfer an input channel to all output channels.
THROUGH:
To transfer the signals directly to the corresponding
output channels.
UNDO: Undo button, to resume to the status before the command
just performed.
: Backspace button, to backspace the latest input button.
2.1.2. Rear Panel
Figure 2- 2 Rear Panel of MMX6464
No.
Name
Description
①
INPUTS
Input signal card slots, 16 in total
② OUTPUTS
Output signal card slots, 16 in total
③
Optional
Ports
Power switch: Switch between AC110V and AC230V to access
different power supply
Page 10
Modular Matrix Switcher 64x64
PTN Electronics Limited 5 www.PTN-electronics.com
TCP/IP: Used for TCP/IP control port
④ RS232
Serial control port, connect with RS232 port of control device.
⑤
Power
ports
Connect with household alternating current power, including one
redundant power.
⑥
GND
connector
Used for system grounding
Note: There are only 16 input and 16 output slots for MMX6464, which enables only
16 input cards and 16 output cards to be ins talled on MMX6464. The input/output
cards can be changed based on your requests and supports hot plug and play.
2.2. Changeable Cards
MMX6464 support expansion through variou s chan geab le in put/ outpu t cards of
different signals including DVI, HDMI, VGA, twisted pair, SDI etc. Here is a brief
introduction to the changeable cards.
2.2.1. 4I-DV & 4O-DV
DVI signal card. (Please check the specification from 5.2.1)
It is fully compatible with HDMI 1.3 and HDCP, but not supporting analogy signal .
It is embedded EDID mana ge ment tec hno logy, supporting DDC .
4I-DV: input card, maximum four input signal. Input signal can pass to output device
through 4O-DV, or pass through other kinds of output cards.
4O-DV: output card, maximum four output signal, output signals from 4I-DV, or other
kinds of input cards.
Pin Layout of the DVI-I connector (Dual-Link). (Female)
PIN
Function
PIN
Function
1
T.M.D.S.Data2-
13
T.M.D.S.Data3+
2 T.M.D.S.Data2+ 14 +5V Power
3 T.M.D.S. Data 2/4 Shi eld 15
Ground (return for +5V,
Hsync and Vsync)
Page 11
Modular Matrix Switcher 64x64
PTN Electronics Limited 6 www.PTN-electronics.com
4 T.M.D.S. Data 4- 16 Hot Plug Detect
5
T.M.D.S. Data 4+
17
T.M.D.S. Data 0-
6 DDC Clock 18 T.M.D.S. Data 0+
7
DDC Data
19
T.M.D.S. Data 0/5 Shi eld
8 Analog Vertical Sync 20 T.M.D.S.Data5-
9
T.M.D.S.Data1-
21
T.M.D.S.Data5+
10 T.M.D.S.Data1+ 22 T.M.D.S. Clock Shield
11
T.M.D.S.Data1/3 Shield
23
T.M.D. S. Clock +
12 T.M.D.S.Data3- 24 T.M.D.S .Clock-
2.2.2. 4I-DS& 4O-DS
Seamless DVI signal card. (Please check the specification from 5.2.2)
It is fully compatible with HDMI 1.3 and HDCP 1.2, and supports seamless
transmission for high-definition DVI, HDMI, VGA, AV, YPbPr signals. It can
automatically identify the format of input signal, and the output resolution can be
adjusted.
It is embedded the EDID management technology, supporting DDC.
4I-DS: seamless input card, maximum four input signal. Input signal can pass to ou tpu t
device through 4O-DS, or pass through other kinds of output cards.
4O-DS: seamless output card, maximum f our output signal. Output signal can come
from 4I-DS, or from other kinds of input cards. It supports off memory for resolution,
signal format, HDCP compliant status.
Note: When 4O-DS works with input cards except 4I-DS, adjust the 4 input signals to
any one of the foll owing 5 r esol utions to enable seamle ss out put: 1024x 768, 128 0x 720,
1600x1200, 1920x1080, 1920x1200.
DVI interfaces on the signal card are same with the interfaces on 4I-DV& 4O-DV.
2.2.3. 4I-HD & 4O-HD
HDMI signal card. (Please check the specification from 5.2.3)
It is embedded the EDID management technology, supporting DDC.
It is also compatible with DVI signal (HDCP required).
4I-HD: input card, maximum four input signal. Input signal can pass to output device
through 4O-HD, or pass through other kinds of output cards.
Page 12
Modular Matrix Switcher 64x64
PTN Electronics Limited 7 www.PTN-electronics.com
4O-HD: output card, maximum four output signal, output signals from 4I-HD, or other
kinds of input cards.
Pin layout of the HDMI connectors (female).
No.
Signal Name
No.
Signal Name
1
TMDS Data 2+
20
SHELL
2
TMDS Data 2 Shield
19
Hot Plug Detect
3
TMDS Data 2-
18
+5V Power
4
TMDS Data 1+
17
Ground
5
TMDS Data 1 Shield
16
DDC Data
6
TMDS Data 1-
15
DDC Clock
7
TMDS Data 0+
14
No Connect
8
TMDS Data 0 Shield
13
CEC
9
TMDS Data 0-
12
TMDS Clock-
10
TMDS Clock+
11
TMDS Clock Shield
2.2.4. 4I-VG & 4O-VG
VGA signal card. (Please check the spec ification from 5.2.4)
Scale all inputs to 1080p.
Compatible with C-Video, Y U V, YC (Factory preset function).
The bandwidth is up to 350MHz (-3dB);
Supporting RGBHV, RGsB, RGBS, RsGsBs, YUV, YC and Composite video.
4I-VG: input card, maximum four input signal. Input signal can pass to output device
through any kinds of output cards.
4O-VG: output card, maximum four VGA output signal and 4 stereo audio outputs,
output video signal from 4I-VG, or other kinds of input cards, and output audio signal
Page 13
Modular Matrix Switcher 64x64
PTN Electronics Limited 8 www.PTN-electronics.com
from the audio of the input signal.
Pin layout of the VG A connectors (female):
Pin Number
Signal Name
Pin Number
Signal Name
Pin 1
RED
Pin 9
KEY/PWR
Pin 2
GREEN
Pin 10
GND
Pin 3 BLUE Pin 11 ID0/RES
Pin 4
ID2/RES
Pin 12
ID1/SDA
Pin 5 GND Pin 13 HSync
Pin 6
RED_RTN
Pin 14
VSync
Pin 7
GREEN_RTN
Pin 15
ID3/SCL
Pin 8
BLUE_RTN
Connect the devices via VGA converting cable as shown below:
Connect with Component Video (YPbPr) Source
Connect with Composite Video (C-VIDEO) Source
2.2.5. 4I-VA
VGA signal card. (Please check the specification from 5.2.5)
Scale all inputs to 1080p.
Compatible with C-Video, Y U V, YC (Factory preset function).
Supporting RGBHV, RGsB, RGBS, RsGsBs, YUV, YC and Composite video.
4I-VA: input card, maximum f o ur VGA inputs and four stereo audio inputs. Input signal
Page 14
Modular Matrix Switcher 64x64
PTN Electronics Limited 9 www.PTN-electronics.com
can pass to output device through any kinds of output cards.
The VGA connector and source connection is same with the 4I-VG.
2.2.6. 4I-SD & 4O-SD
SDI signal card. (Please check the specification from 5.2.6)
It is compatible with different SDI signal formats, including SD/HD/3G-SDI (adaptive)
Every port has loop output for loc al monitoring.
4I-SD: input card, maximum four input signal. Input signal can pass to output device
through 4O-SD, or pass through other kinds of output cards.
4O-SD: output card, maximum four output signal, output signals from 4I-SD, or other
kinds of input cards.
The BNC connector is shown as the figure below.
Sleeve
( )
Tip (+)
BNC Connector
2.2.7. 4I-TP & 4O-TP
Twisted pair card (HDMI/DVI extender). (Please check the specification from 5.2.7)
Support HDTV, compatible with HDMI1.3 and HDCP
4I-TP: input card, maximum input four HDMI T P signal. In put signal can pass to output
device through 4O-TP, or pass through other kinds of output cards, need to work with
TPHD402T.
Page 15
Modular Matrix Switcher 64x64
PTN Electronics Limited 10 www.PTN-electronics.com
4O-TP: output card, maximum output four HDMI TP signal, output signals from 4I-TP,
or other kinds of input cards, need to work with TPHD402R.
Pin layout of the RJ 45 connectors:
Two different connect ion sta nd ar ds can be chose; the connectors of same cable
should use the same standard.
TIA/EIA T568A
TIA/EIA T568B
Cable color Cable color
1 green white 1 orange white
2 green 2 orange
3 orange white 3 green white
4 blue 4 blue
5 blue white 5 blue white
6 orange 6 green
7 brown white 7 brown white
8 brown 8 brown
Notice: Cable connectors MUST be metal one, and the shielded layer of cable MUST
be connected to the connector’s metal shell, to well share the grounding.
2.2.8. 4I-UH & 4O-UH
4K HDMI signal card. (Please check the specification from 5.2.8)
Support hot-plug, HDMI 1.4& HDCP 1.4 compliance; Compatible with DVI signal;
Support high-definition HDMI source up to 4kx2k, 1080p 3D compliance; Provide
auxiliary audio port as supplement to HDMI embedded audio.
It is also embedded the EDID management technology.
4I-UH: input card, maximum four input signal. Input signal can pass to output device
through 4O-UH, or pass through other kinds of output cards.
Page 16
Modular Matrix Switcher 64x64
PTN Electronics Limited 11 www.PTN-electronics.com
4O-UH: output card, maximum four output signal, output signals from 4I-UH, or other
kinds of input cards, HDCP compliant status settable via RS232 comman d
2.2.9. 4I-UF & 4O-UF
4K optical signal card. (Please chec k the specification from 5.2.9)
Support hot-plug; High bandwidth: 10.2Gbps; Compliant with HDMI 1.4, capable to
transmit 4K×2K& 1080P 3D (max) signals; Support multi-mode transmission up to
300m and single mode transmission up to 1km.
4I-UF: input card with indicators, maximum four input signal, corresponding indicator
illuminates green when there is input signal. Input signal can pass to output device
through 4O-UF, or pass through other kinds of output cards.
4O-UF: output card with indicators, maximum four output signal, output signals from
4I-UF, or other kinds of input cards; corresponding indicator illuminates green when
there is output signal.
Note: Use the 4I-UF/ 4O-UF with optical fiber transmitter/ receiver.
2.2.10. 4I-BT & 4O-BT
Twisted pair card (HDMI/DVI extender). (Please check the specification from 5.2.10)
Support hot-plug, support HDTV, compatible with HDBT 1.0, HDMI1.4a& HDCP1.4;
Wide resolution range from 480p to 4kx2k, 1080p 3D compliant; Extend HDBT signal
up to 70m at 1080p or 40m at 4k; Bi-directional RS232 transmission on single cable;
Auxiliary audio ports support stereo signal.
It is also embedded the EDID management technology.
4I-BT: input card, maximum input four HDMI TP signal. I nput signal can pass to output
device through 4O-BT, or pass through other kinds of output cards, need to work with
HDBT transmitter (e.g. TPHD402T).
Page 17
Modular Matrix Switcher 64x64
PTN Electronics Limited 12 www.PTN-electronics.com
4O-BT: output card, maximum output four HDBT signal, output signals from 4I-BT, or
other kinds of input cards, need to work with HDBT receiver (e.g. TPHD402R).
3. System Connection
3.1. Usage Precautio ns
1) System should be installed in a clean environment and has a prop temperat ure
and humidity.
2) All of the power switches, plugs, sockets and power cords should be insulated and
safe.
3) All devices should be connected before power on.
Page 18
Modular Matrix Switcher 64x64
PTN Electronics Limited 13 www.PTN-electronics.com
3.2. Connection Diagram
Figure 3- 1 System Diagram
3.3. Application
MMX serie s has a good application in various occasi o ns, su ch as radio & television,
multi-media meeting room, big screen displaying, television educat ion and command
& control center etc.
Page 19
Modular Matrix Switcher 64x64
PTN Electronics Limited 14 www.PTN-electronics.com
4. Control Operations
Users can control MMX6464 rapidly and directly with its front panel buttons. To switch
AV/ A/ V signal, please operate the buttons under the following format:
Format: “Input Channel” + “AV” +“Output Channel”+“Enter”
Note:
1) “Switch Mode”: Audio & Video synchronal (AV) or separate switching mode (Audio/
Video)
2) “Input Channel”: Fill with the number of input channel to be controlled,
3) “Output Channel”: Fill with the number of output channels to be controlled. Press
“All” to select all the outputs.
4) Use “,” button to separate multiple I/O channels, and press “ENTER” button to
confirm the operation.
5) The input/output channels on the rear panel are counting from left to right, top to
bottom.
6) The input delay time betw een tw o numbers of ev ery input& output chann el m ust b e
less than 5 seconds; otherwise the operation will be cancelled.
Example:
1. To transfer input 1 to output 11, press input “1”, output “0” “1” and “Enter”.
2. To transfer signals from input 1 to all output channels, press buttons in this order:
“1”, “All”.
Other Functional Buttons:
Buttons Description Operation
UNDO
return to the previous
status
Status 1: Input 6 -> output 6
Press input “6” + “AV”+ output 4 to change
the connection. Press “Undo” to return to
Status 1.
Backspace the last
operation
If you press buttons “1”, “AV”, “2”, “” in
order , then “2” will be canceled.
THROUGH
Get straight I/O
connection, e.g. input 1->
output 1, input 2-> output
2.
Format: “Input Channel”+”Through”
If you press buttons “ALL”, “THROUGH” in
order, then the result will be like input 1
output 1, input 2output 2, input 3output
3 … input 16output 16.
Page 20
Modular Matrix Switcher 64x64
PTN Electronics Limited 15 www.PTN-electronics.com
4.1. IR Remote control
With the IR remote, MMX6464 could be controlled remotely. As the function buttons on
the IR remote are the same with the ones on the front panel, the IR remote shares the
same operations and commands with the control panel.
Press the buttons under below format:
“Input Channel” + “Switch Mode” +“Output Channel”
Figure 4- 1 Panel of the IR Remote
Input channel buttons,
including 1~10+
Menu buttons, including
switching buttons and
function buttons
Output channel buttons,
including 1~10+
Input channel buttons,
including 1~10+
Menu buttons, buttons
VIDEO and AUDIO are
not available.
Output channel buttons,
including 1~10+
Page 21
Modular Matrix Switcher 64x64
PTN Electronics Limited 16 www.PTN-electronics.com
4.2. RS232 Control
4.2.1. Connection of RS232 Communication Port
Except the front control panel and IR remote, MMX6464 can be contro lled by far-end
control system or through the Ethernet control via the RS-264 communication port.
This RS-264 communication port is a female 9- D connector. The definition of i ts pin
layout is shown in the table below.
No. Function
1 N/u Unused
2 Tx Transmit
3 Rx Receive
4 N/u Unused
5 Gnd Ground
6 N/u Unused
7 N/u Unused
8 N/u Unused
9 N/u Unused
When MMX6464 connects to the RS232 port of a computer with control software,
users can control it by that comput er. To control the sw itcher, users need to use RS232
control software.
4.2.2. RS232 Communication Commands
With this command system, users are able to control and operate the MMX6464
with RS232 software remotely.
Communication protoc ol: Baud rate: 9600; Data bit: 8; Stop bit: 1; Parity bit: none.
Type
Command
Description
Commands for Main Unit
/*Type;
Inquire the models information.
/%Lock;
Lock the keyboard of the control panel on the
Matrix.
/%Unlock;
Unlock the keyboard of the control panel on the
Matrix.
/^Version; Inquire the version of firmware
/:MessageOff;
Turn off the feedback command from the com
port. It will only s how the “switcher OK”.
/:MessageOn;
Turn on the feedback command from the com
port.
Undo.
To cancel the previous operation.
Demo.
Switch to the “demo” mode, 1->1, 2->2, 3->3 …
and so on.
Page 22
Modular Matrix Switcher 64x64
PTN Electronics Limited 17 www.PTN-electronics.com
[x]All.
Transfer signals from the input channel [x] to all
output channels
All#.
Transfer all input signals to the corresponding
output channels respectively.
All$. Switch off all the output chann els.
[x]#.
Tr ansfer s ign als fr o m t he inp ut channel [x] to the
output channel [x].
[x]$. Switch off the output channel [x].
All@.
Switch on all the output.
[x]@. Switch on output [x].
[x1]V[x2].
Transfer the video signals from the input
channel [x1] to the output channel [x2].
[x1]A[x2].
Transfer the audio signals from the input
channel [x1] to the output channel [x2].
[x1]B[x2].
Tr ansfer signa l from t he input channe l [x 1] to the
output channel [x2].
Status[x].
Inquire the input channel to the output channel
[x].
Status.
Inquire the input channel to the output channels
one by one.
Save[Y].
Save the present o peration to the preset
command [Y]. [Y] ranges from 0 to 9.
Recall[Y]. Recall the preset command [Y].
Clear[Y].
Clear the preset com mand [Y].
PWON. Work normally.
PWOFF.
Enter in standby mode.
HDCPON. Turn on the HDCP output.
HDCPOFF.
Turn off the HDCP output.
/V00. Inquire the version of backboard software.
UpgradeIntEDID[x].
Upgrade built-in EDID data. Supports 6 types of
EDID data (see Note 6). When the switcher gets
the command, it will show a message to send
EDID file (.bin file).
EDIDUpgrade[x].
Upgrade EDID data of input ports
When the switcher gets the command, it will
show a message to send EDID file (.bin file).
Operations will be canceled after 10 seconds.
Page 23
Modular Matrix Switcher 64x64
PTN Electronics Limited 18 www.PTN-electronics.com
EDID/[x]/[y].
Set the EDID data of input port [x] to built-in
EDID data of type [y].
The value of [y] v ar ies from 1~6. The EDID data
types are same as mentioned above.
EDIDG[x].
Get EDID data from output channel X and
display the data on serial port control software.
[x] is the output port number.
EDIDMInit.
Recover the factory default EDID data for every
input channel.
EDIDM[X]B[Y].
Manually EDID switching. Enable input [Y] to
learn the EDID data of output[ X ]. If there is
problem learning the EDID data, it will
automatically set the default EDID data for input
[Y].
USER/[Y]/[X]:*****;
Custom command for si gnal cards, [Y]=I/O; [X]=
port number; *****: User-defina ble comman d,
e.g. 0623%
0911%.
Restore factory default.
Commands for Signal Cards
4I-VA
USER/I/[x]:0622%;
Set the signal of input channel [x] to VGA.
USER/I/[x]:0623%;
Set the signal of input channel [x] to YCBCR.
USER/I/[x]:0624%;
Set the signal of input channel [x] to SVIDEO.
USER/I/[x]:0625%;
Set the signal of input channel [x] to CVIDEO.
USER/I/[x]:0626%;
Set the resolution of input [x] to
1024x768@60Hz.
USER/I/[x]:0627%;
Set the resolution of input [x] to
1280X720@60Hz.
USER/I/[x]:0628%;
Set the resolution of input [x] to
1280X800@60Hz.
USER/I/[x]:0619%;
Set the resolution of input [x] to
1360X768@60Hz.
USER/I/[x]:0621%;
Set the resolution of input [x] to
1600X1200@60Hz.
USER/I/[x]:0629%;
Set the resolution of input [x] to
1920X1080@60Hz.
USER/I/[x]:0620%;
Set the resolution of input [x] to
1920X1200@60Hz.
USER/I/[x]:0617%;
Restore to factory default.
USER/I/[x]:0606%;
Auto-adjust VGA signal
Page 24
Modular Matrix Switcher 64x64
PTN Electronics Limited 19 www.PTN-electronics.com
USER/I/[x]:0698%;
Update software
4I-VG
USER/I/[x]:0698%;
Update software
USER/I/[x]:0622%;
Set the signal of input channel [x] to VGA.
USER/I/[x]:0623%;
Set the signal of input channel [x] to YCBCR.
USER/I/[x]:0624%;
Set the signal of input channel [x] to SVIDEO.
USER/I/[x]:0625%;
Set the signal of input channel [x] to CVIDEO.
USER/I/[x]:0626%;
Set the resolution of input [x] to
1024x768@60Hz.
USER/I/[x]:0627%;
Set the resolution of input [x] to
1280X720@60Hz.
USER/I/[x]:0628%;
Set the resolution of input [x] to
1280X800@60Hz.
USER/I/[x]:0629%;
Set the resolution of input [x] to
1920X1080@60Hz.
4I-DS
USER/I/[x]:02xx%;
Set the brightness of input [x] to xx, xx=00~99
USER/I/[x]:03xx%;
Set the contrast of input [x] to xx, xx=00~ 99
USER/I/[x]:04xx%;
Set the saturation of input [x] to xx, xx=00~99
USER/I/[x]:05xx%;
Set the sharpness of input [x] to xx, xx=00~99
USER/I/[x]:0606%;
(For 4I-DS/ VA) Auto-adjust VGA input signal
USER/I/[x]:0607%;
Set picture’s color temperature
USER/I/[x]:0608%;
Configure image scale
USER/I/[x]:0614%;
Configure picture mode
USER/I/[x]:0617%;
Restore to factory default.
USER/I/[x]:0619%;
Set the resolution of input [x] to 1360x768, HD
USER/I/[x]:0626%;
Set the resolution of input [x] to 1024x768, XGA
USER/I/[x]:0627%;
Set the resolutio n of input [x] to 1280x720, 720P
USER/I/[x]:0628%;
Set the resolution of input [x] to 1280x800,
WXGA
USER/I/[x]:0629%;
Set the resolution of input [x] to 1920x1080,
1080P
USER/I/[x]:0620%;
Set the resolution of input [x] to 1920x1200,
WUXGA
Page 25
Modular Matrix Switcher 64x64
PTN Electronics Limited 20 www.PTN-electronics.com
Note:
1. Please disconnect all the twisted pairs before sending command
EDIDUpgrade[X].
2. In above commands, “[”and “]” are symbols f or ea sy reading and do not need to
be typed in actual operation.
3. Please remember to end the commands with the ending symbols “.” or “;”.
4. Type the command carefully, it is case-sensitive.
5. Commands pertaining to EDID only avails for signal cards that support EDID
management.
USER/I/[x]:0621%;
Set the resolution of input [x] to 1600x1200,
UXGA
USER/I/[x]:0698%;
Software update
USER/I/[x]:0686%;
Set the output signal of input [x] to HDMI
USER/I/[x]:0687%;
Set the output signal of input [x] to DVI
4O-DS
USER/O/[x]:0201%;
Set the input sourc e of output [x] to YPbPr
USER/O/[x]:0202%;
Set the input sourc e of output [x] to VGA
USER/O/[x]:0203%;
Set the input sourc e of output [x] to C-VIDEO
USER/O/[x]:0804%;
Set the resolution of output [x] to 1280x720P
@60Hz
USER/O/[x]:0813%;
Set the resolution of output [x] to 1280x1080P
@60Hz
USER/O/[x]:0824%;
Set the resolution of output [x] to 1024x768
@60Hz
USER/O/[x]:0826%;
Set the resolution of output [x] to 1280x1024
@60Hz
USER/O/[x]:0837%;
Set the resolution of output [x] to 1920x1200
@60Hz
USER/O/[x]:0106%;
Switch on the HDCP compliance of output [x]
USER/O/[x]:0107%;
Switch off the HDCP compliance of output [x]
GetResolution[x].
Capture output resolutio n of output [x]
GetVGAPortMode[x
].
Inquire the output s tatus of VGA port [x]
4I-UH/BT
AUDIO[X]I[Z].
Select audio source from audio input s or AV
signal inputs
Page 26
Modular Matrix Switcher 64x64
PTN Electronics Limited 21 www.PTN-electronics.com
6. The switcher bo ast s 6 i n-built EDID data, the char t b elow illustrates the detailed
information:
No. Detailed Information
1 1080p 2D 5.1CH
2 1080p 2D 2.0CH
3 720p 2D 5.1CH
4 720p 2D 2.0CH
5 4kx2k 2D 5.1CH
6 4kx2k 2D 2.0CH
Update in-built EDID data by sending command UpgradeIntEDID[x]..
Examples:
1、 Transfer signals from an input channel to all output channels: [x]All.
Example: Send “3All.” to transfer signals from the input 3 to all output channels.
2、 Transfer all input signals to corresponding output channels respectively:
All#.
Example: If this command is carried out, the stat us of matrix will be: 1->1, 2->2, 3->3,
4->4…… 8->8….
3、 Switch off all the output channels: All$.
Example: After running this command, there will be no signals on all the outputs.
4、 Switch off the detail feedback command from the COM port: /:MessageOff;
But, it will leave the “switch OK” as the feedback, when you switch the matrix.
5、 Switch on the detail feedback command from the COM port: /:MessageOn;
It will show the detail switch information when it switc h. Example: when switch 1->2, it
will feedback “AV01 to 02”.
6、 Transfer signals from an input channel to corresponding output channel:
[x]#.
Example: “5#.” to trans fer signals from the input5 to the output5.
7、Switch off an output channel: [x]$.
Example: “5$.” to switch off the output 5.
8
、Switch signal: [x1] B[x2].
Example: “12B12,13,1 5.” to transfer signal from the input12 to the output No.12, 13,15.
9
、Inquire the input channel to the output channel [x]: Status[x].
Example: Send “Status3.” to inquire the input channel to the output 3.
10、Inquire the input channel to the output channels one by one: Status.
Page 27
Modular Matrix Switcher 64x64
PTN Electronics Limited 22 www.PTN-electronics.com
Example: “Status.” to inquire the input channel to the output channels one by one.
11
、Save the present operation to the preset command [Y]: Save[Y].
Example: “Save7.” to save the present operation to the preset command No.7.
12、Recall the preset command [Y]: Recall[Y].
Example: “Recall5.” to recall the preset command No.5.
13
、Clear the preset command [Y]: Clear[Y].
Example: “Clear5.” to clear the preset command No.5.
14
、EDID management command:. EDIDM[X]B[Y].
Example: “EDIDM5B3.” to enable input 3 to learn the EDID data of output 5.
15、Command for signal cards: USER/[Y]/[X]*****.
Example: “USER/I/7:0623%;” to set the input 7 to support YPbPr signal, the card is
plugged in the second input slot of the matrix.
Page 28
Modular Matrix Switcher 64x64
PTN Electronics Limited 23 www.PTN-electronics.com
4.3. TCP/IP Control (Optional)
4.3.1. Control Modes
TCP/IP default settings: IP is 192.168.0.178, Gateway is 192.168.0.1, and Serial Port
is 4001. IP & Gateway can be changed as you need, Serial Port cannot be changed.
Controlled by Single PC
Connect a computer to the TP port of the MMX6464, and set its IP address and
gateway to the same IP section as the default IP of the MMX6464 (192.168.0.178).
Controlled by PC(s) in LAN
The MMX6464 can be connected with a router to make up a LAN with the PC(s), this
make it able to be c ontrolled in a LAN. When control, just make sure the MMX6464’s
IP section is the same with the router. Please connect as the following figure for LAN
control.
Same IP as the
switcher
Page 29
Modular Matrix Switcher 64x64
PTN Electronics Limited 24 www.PTN-electronics.com
Step1. Connect the TCP/IP port of the MMX6464 to Ethernet port of PC with twisted
pair.
Step2. Set the PC’s IP address and gateway to the same IP section as the
MMX6464. Do please remember the PC’s original IP address and gateway.
Step3. Set the MMX6464’s IP address and gateway to the same IP section as the
router.
Step4. Set the PC’s IP address and gateway as the original one.
Step5. Connect the MMX6464 and PC(s) to the router. In the same LAN, each PC is
able to control the MMX6464 asynchronously.
4.3.2. TCP/IP Settings
Step1. Connect the TCP/IP port of the MMX6464 to Ethernet port of PC with twisted
pair.
Step2. Set the PC’s IP and gateway to the same IP section as the default IP of the
MMX6464 (192.168.0.178).
Step3. Enter the http://192.168.0.178:100 to the Internet Explorer, you will see the
LOGIN page.
Step4. Enter user nam e “admin” and password “admin”, then pr ess t he Enter button.
(Not the Enter key on your keyboard.) Then you can enter the configuration
page to configure the IP port, including the IP reset, Serial reset and
password reset etc. As pictur e below :
Page 30
Modular Matrix Switcher 64x64
PTN Electronics Limited 25 www.PTN-electronics.com
Step5. Change IP/Serial Port
Change IP
a) Select the tab “system info”, and then you are able to change the IP.
b) Press the butt on Apply to save your settings. Then the PC(s) in this LAN
(connected with this router) will be able to control the matrix switcher.
Change Serial Port
a) Select the tab “serial info”, and then you are able to change the serial
port.
b) Set the port number to 4001 (unique, other numbers are unavai lable).
c) Press the button Apply on present page to save your sett ing s.
Step6. Select the tab “reset device”, then your settings will be loaded to the
MMX6464.
5. Specification
5.1. Main Unit
Control parts
Serial control port
RS-232, 9- female D
connector
Configurations
2 = TX, 3 = RX, 5
= GND
Installation Rack Mountable
Front panel
control
Buttons
Options TCP/IP control
General
Power Supply
100VAC ~ 240VAC,
Power
550W (Max)
Page 31
Modular Matrix Switcher 64x64
PTN Electronics Limited 26 www.PTN-electronics.com
50/60Hz
Consumption
Temperature -10 ~ +40℃ Humidity 10% ~ 90%
Dimension
(W*H*D)
483 x 438 x 320mm
(10U high)
Weight 8Kg
5.2. Changeable Cards
5.2.1. 4I-DV & 4O-DV
Input
Output
Input
4 DVI
Output
4 DVI
Input
Connector
Female DB24+5
Output
Connector
Female DB24+5
Input Level
T.M.D.S. 2.9V~3.3V
output Level
T.M.D.S. 2.9V~3.3V
Input
Impedance
75Ω
Output
Impedance
75Ω
General
Gain
0 dB
Bandwidth
340 MHz (10.2 Gbit/s)
Video Signal
DVI 1.0/HDMI 1.3 full
digital T.M.D.S signal
Switching
Speed
200ns (Max.)
Max
Time-delay
5nS (±1nS) Crosstalk <-50dB@5MHz
EDID and
DDC
Supports Extended Display Identific ation Data (EDID) and Display
Data Channel (DDC) data using DVI and HDMI standards. EDID
and DDC signals are actively buffered
HDCP Compliant with HDCP using DVI and HDMI 1.3 standards
5.2.2. 4I-DS & 4O-DS
Input
Output
Input
4 DVI
Output
4 DVI
Input
Connector
Female DB24+5
Output
Connector
Female DB24+5
Input Level T.M.D.S. 2.9V~3.3V
output
Level
T.M.D.S.
2.9V~3.3V
Input
Impedance
75Ω
Output
Impedance
75Ω
General
Gain 0 dB Bandwidth
340 MHz (10.2
Gbit/s)
Video Signal DVI,HDMI,VGA,C-VIDEO,YPbPr
Switching
Speed
200ns (Max.)
Max
Time-delay
5nS (±1nS) Crosstalk <-50dB@5MHz
Page 32
Modular Matrix Switcher 64x64
PTN Electronics Limited 27 www.PTN-electronics.com
EDID and
DDC
Supports Extended Display Identific ation Data (EDID) and Display
Data Channel (DDC) data using DVI and HDMI standards. EDID
and DDC signals are actively buffered
HDCP
Compliant with HDCP using DVI and HDMI 1.3 standards
5.2.3. 4I-HD & 4O-HD
Input
Output
Input
4 HDMI
Output
4 HDMI
Input
Connector
Female HDMI
Output
Connector
Female HDMI
Input Level
T.M.D.S. 2.9V/3.3V
output Level
T.M.D.S. 2.9V/3.3V
Input
Impedance
75Ω
Output
Impedance
75Ω
General
Gain
0 dB
Bandwidth
6.75Gbit/s
Video Signal
DVI 1.0/HDMI 1.4a full
digital T.M.D.S signal
Max
Time-delay
5nS (±1nS)
Switching
Speed
200ns (Max.) Crosstalk <-50dB@5MHz
EDID and
DDC
Supports Extended Display Identific ation Data (EDID) and Display
Data Channel (DDC) data using DVI and HDMI standards. EDID
and DDC signals are actively buffered
HDCP Compliant with HDCP using DVI and HDMI 1.4a standards
5.2.4. 4I-VG & 4O-VG
Input
Output
Input
4 VGA
Output
4 VGA
Input
Connector
Female 15 pin HD
Output
Connector
Female 15 pin HD
Input Level
0.5 ~ 2.0Vp-p
Output Level
0.5 ~ 2.0Vp-p
Input
Impedance
75Ω
Output
Impedance
75Ω
General
Gain 0 dB Bandwidth
350MHz (-3dB), fully
load
Video Signal
VGA-UXGA, RGBHV, RGBS, RGsB, RsGsBs, component video,
S-video & C-video.
Switching
Speed
200ns (Max.) Crosstalk <-50dB@5MHz
Page 33
Modular Matrix Switcher 64x64
PTN Electronics Limited 28 www.PTN-electronics.com
5.2.5. 4I-VA
Input
Video
Audio
Input 4 VGA Input 4 Stereo Audio
Input
Connector
Female 15 pin HD
Input
Connector
3P Captive connector
Input Level 0.5 ~ 2.0Vp-p CMRR >90dB @20Hz ~ 20KHz
Input
Impedance
75Ω
Input
Impedance
>10KΩ
General
Gain 0 dB Bandwidth
YPbPr:170MHz;
C-video:150MHz;
VGA:170MHz
Video Signal
VGA-UXGA, RGBHV, RGBS, RGsB, RsGsBs, component video,
S-video& composite video.
Switching
Speed
200ns (Max.) Crosstalk <-50dB@5MHz
5.2.6. 4I-SD & 4O-SD
Input
Output
Input
4 SDI
Output
4 SDI
Input
Connector
Female BNC
Output
Connector
Female BNC
Input Level
0.8Vp-p ± 10%
output Level
0.8Vp-p ± 10%
Input
Impedance
75Ω
Output
Impedance
75Ω
General
Gain Unity
Maximum
Data Rate
2.97 Gbps
Transmission
Distance
300M (Max.) Data rate Lock Auto
Input Return
Loss
<-14 dB @ 1 MHz ~ 1.5
GHz
Input Return
Loss
<-14 dB @ 1 MHz ~
1.5 GHz
Video
Standard
SMPTE 292M, SMPTE
259M, SMPTE 424M,
ITU-RBT.601,
ITU-RBT.1120
Data Type 8bit, 10bit
Audio Bits per
Sample
18 bits per channel, 2 channels (L, R)
Page 34
Modular Matrix Switcher 64x64
PTN Electronics Limited 29 www.PTN-electronics.com
5.2.7. 4I-TP & 4O-TP
Video Input
Video Output
Input
4 RJ45
Output
4 RJ45
Input
Connector
Female RJ45
3.5mm mini jack for IR
3 poles captive screw
connector for RS232
Output
Connector
Female RJ45
3.5mm mini jack for
IR
3 poles captive screw
connector for RS232
Input
Impedance
75Ω
Output
Impedance
75Ω
Video General
Gain
0dB ~ 10dB@100MHz
Bandwidth
6.75Gbps
Resolution
range
800x600 ~ 1920x1200 Transmission
Distance
70M(Max)
SNR
>70dB@
100MHz-100M
Return Loss <-30dB@ 5KHz
THD ＜0.005%@1KHz Min.～Max.
Level
＜0.3V ~ 1.45Vp-p
HDMI
Standard
Support HDMI1.4a and
HDCP
Differential
Phase Error
±10° @
135MHz_100M
5.2.8. 4I-UH & 4O-UH
Input
Video Input
Audio Input
Input 4 HDMI Input 4 Analog
Input Connector Female HDMI
Input
Connector
3.5mm pluggable
terminal block
Min.～Max.
Level
T.M.D.S. 2.9V~3.3V
Input
Impedance
75Ω
Input Impedance 100Ω (Differential)
Frequency
Response
20Hz～20K Hz
Output
Video Output
Audio Output
Output 4 HDMI Output 4 Stereo
Output
Connector
Female HDMI
Output
Connector
3.5mm Stereo audio
connector
Min.～Max.
Level
T.M.D.S. 2.9V~3.3V
Output
Impedance
75Ω
Output
Impedance
100Ω (Differential)
Frequency
Response
20Hz～20K Hz
Page 35
Modular Matrix Switcher 64x64
PTN Electronics Limited 30 www.PTN-electronics.com
General
Gain
0dB
Bandwidth
6.75Gbps
Max Resolution 4Kx2K Crosstalk <-50dB@5MHz
Transmission
Distance
1080P≤70m
4Kx2K ≤ 40m
Switching
Speed
200ns (Max.)
Work
Temperature
-10℃～+40℃
Reference
Humility
10%～90%
SNR
>70dB@
100MHz-100M
Return Loss <-30dB@ 5KHz
Supported Audio
Format
Embedded HDMI audio: PCM, Dobly Digital, DTS, DTS-HD
Analog audio: PCM
HDMI Standard
Support HDMI1.4& DVI1.0
EDID& HDCP
Management
Compliant with HDCP 1.4; Support manual EDID management
5.2.9. 4I-UF & 4O-UF
Input
Output
Input 4 Fiber Optical Output 4 Fiber Optical
Input
Connector
SPF Fiber Optical
Connector
Output
Connector
SPF Fiber Optical
Connector
Fiber Type
Multi-mode, Single
mode
Fiber Type
Multi-mode, Single
mode
General
Data Rate 10.2 Gbps Color Depth 8bit, 10bit, 12bit, 16bit
Work
Temperature
0～55℃
Reference
Humility
10%～90%
Optical Fiber Mode
Connector
LC connector
Resolution
Up to 4Kx2K
Transmission
Distance
1km (Single mode transmission, using Single Mode Optical
Module and OM3 Single Mode Fiber Cable)
300m (Multi-mode transmissio n, using Sin gle/ M ulti mode O ptica l
Module and OM3 Mul t i-Mode Fiber Cable)
Data Rate
10.2Gbit/s
Page 36
Modular Matrix Switcher 64x64
PTN Electronics Limited 31 www.PTN-electronics.com
5.2.10. 4I-BT & 4O-BT
Input
Video Input
Audio Input
Input 4 HDBT Input 4 Stereo
Input
Connector
4 Female RJ45 (with
dual-color indicator)
Input
Connector
3.5mm Stereo audio
connector
Min.～Max.
Level
T.M.D.S 2.9V～3.3V
Input
Impedance
75Ω
Input
Impedance
100Ω (Differential)
Frequency
Response
20Hz～20K Hz
Output
Video Output
Audio Output
Output 4 HDBT Output 4 Stereo
Output
Connector
4 Female RJ45 (with
dual-color indicator)
Output
Connector
3.5mm Stereo audio
connector
Min.～Max.
Level
T.M.D.S 2.9V～3.3V
Output
Impedance
75Ω
Output
Impedance
100Ω (Differential)
Frequency
Response
20Hz～20K Hz
Control Part
Control
Signal
4 RS232
Control
Connector
3-pin pluggable
terminal block
Protocol
TCP/IP
General
Gain
0dB
Bandwidth
6.75Gbps
Max
Resolution
4Kx2K
Crosstalk <-50dB@5MHz
Transmission
Distance
1080P≤70m
4Kx2K ≤ 40m
Switching
Speed
200ns (Max.)
Work
Temperature
-10℃～+40℃
Reference
Humility
10%～90%
SNR
>70dB@
100MHz-100M
Return Loss <-30dB@ 5KHz
Supported
Audio Format
Embedded HDMI audio: PCM, Dobly Digital, DTS, DTS-HD
Analog audio: PCM
HDMI
Standard
Support HDMI1.4
EDID& HDCP
Management
Compliant with HDCP 1.4; Support manual EDID management
Page 37
Modular Matrix Switcher 64x64
PTN Electronics Limited 32 www.PTN-electronics.com
6. Troubleshooting & Maintenance
Problems
Causes
Solutions
Output image with ghost
Bad quality of the
connecting cable
Try another high quality
cable
Impropriate image setting
of the displayer
Adjust corresponding
image settings
Output image with color
losing or no video s i gnal
output
Fail connection
Reconnect the displayer
and the matrix
No output image when
switching
No signal at the input /
output end
Check with oscillosc ope or
multimeter if there is any
signa l at the input/ output
end.
Fail or loose connection
Make sure the connection
is good
The switcher is broken
Send it to authorized
dealer for repairing.
IR remote does not work
Run out of battery Change for another battery
IR remote is broken
Send it to authorized
dealer for repairing.
POWER indicator doesn’t
work or no respond to any
operation
Fail connection of pow er
cord.
Make sure the power cord
connection is good.
EDID management does
not work normally
The HDMI cable is broken
at the output end.
Change for another HDMI
cable which is in good
working condition.
There is a blank sc reen on
the display when switching
The display does not
support the resolution of
the video source.
Switch again.
Manage the EDID data
manually to make the
resolution of the video
source automatically
compliant with the output
resolution.
Static becomes stronger
when connecting the video
connectors
Bad grounding
Check the grounding and
make sure it is connected
well.
Page 38
Modular Matrix Switcher 64x64
PTN Electronics Limited 33 www.PTN-electronics.com
Cannot control the device
by control device (e.g. a
PC) through RS232 port
Wrong RS232
communication parameters
Type in correct RS232
communication
parameters.
Broken RS232 port
Send it to authorized
dealer for checking.
Cannot control the device
by front panel butto ns while
can control it through
RS232 port
The front panel buttons are
locked
Send command 50605% to
unlock the front panel
buttons.
Cannot control the device
by RS232 / IR remote /
front panel buttons
The device has already
been broken.
Send it to authorized
dealer for repairing.
If your problem persists after following the above troubleshooting steps, seek further
help from authorized dealer or our technical support.
Page 39
Modular Matrix Switcher 64x64
PTN Electronics Limited 34 www.PTN-electronics.com
7. After-sales Service
If there appear som e problems when running MMX6464, please check and deal with
the problems referring to this user manual. Any transport costs are borne by the users
during the warranty.
1) Product Limited Warranty: PTN warrants that its products will be free from
defects in materials and workmanship for three years, which starts from the first
day you buy this product (The purchase invoice shall prevail).
Proof of purchase i n the form of a bill of sale or receipted invoice which is evide nc e
that the unit is within the Warranty period must be presented to obtain warranty
service.
2) What the warranty does not cover (servicing available for a fee):
Warranty expiration.
Factory applied serial number has been altered or removed from the product.
Damage, deterioration or malfunction caused by:
Normal wear and tear
Use of supplies or parts not meeting our specific at i ons
No certificate or invoice as the proof of warranty.
The product model showed on the warranty card does not match with the
model of the product for repairing or had been altered.
Damage caused by force majeure.
Servicing not authorized by PTN
Any other causes which does not relate to a product defe ct
Delivery, installation or labor charges for installation or setup of the product
3) Technical Support: Email to our after-sales department or make a call, please
inform us the following information about your cases.
Product version and name.
Detailed failure situations.
The formation of the cases.
Remarks: For any more questions or problems, please try to get help from your
local distributor, or email PTN at
support@PTN-electronics.com.
Page 40
www.PTN-electronics.com
PTN Electronics Limited
Tel: +86-755-2846 1819
Fax: +86-755-8471 7796
Email: info@PTN-electronics.com
Website: www.PTN-electronics.com
Loading...