POWER-TO-GO
LED
LED Flame On/O
Power On/O
The battery must be fully charged prior to use. It takes approximately
4 hours to fully charge your Speaker (from depleted battery).
Using the provided Micro USB cable, connect your
Speaker (micro USB port) to the AC adapter (USB port).
Flame
Speaker
USER MANUAL
• Make sure the Bluetooth® function is available on your cell
phone. Specic pairing procedures will be dierent depending
on dierent cell phones. For detailed information, please refer to
your cell phone’s User Guide.
• After successful pairing, devices will memorize each other.
Therefore no pairing will be needed the next time you power up
your Speakers.
1. Keep the distance between the cell phone and the speaker
within 3 feet ( for pairing only).
2. Turn on the speaker by pressing the “Power On/O” button
3. The tone prompt will sound. The unit will automatically enter into
pairing mode.
4. Activate the Bluetooth function of the cell phone to search
for the Bluetooth devices. After nishing the search, select “A1+”
in the device list displayed.
5. Your A1+ speaker is ready to use.
Press and release the
Power On/O button
Vol Down
Play/Pause
TF Card Slot
Long Press
TF CARD MODE
Go to next song
Press Button
Press to play/pause the music.
Vol Up
Charging
Port
50 Hz-20KHZ
1500 mAh Li-Ion
33 ft (10m)
4 Hours
10 Hours
Long Press
(automatic after inserting TF card)
Go to previous song
Press Button
Play/Pause
Press Button
TWS MODE
1. Turn o the Bluetooth mode on your mobile device.
2. Turn on the speakers by pressing the “Power On/O” button
3. On either speaker, press and hold the “LED Flame On/O” button
for 3-5 seconds, and wait until you hear a “ding-dong” conrmation
tone.
The speakers are now connected, and you can connect your
Bluetooth device.
LED FLAME
To use the LED ame function, press and release the LED Flame On/O
button once. The lamp will turn on to the dimmest setting. There are 3
brightness levels; press and release to change the brightness.
Using the provided Micro USB cable, connect your Speaker
(Micro USB port) to the computer/laptop (USB port).
• Keep Speaker away from any heat source
• Always adjust the Speaker volume to a suitable level to avoid
hearing damage or damage to the unit.
• If not using the Speaker for a long period of tie, keep the internal
battery charged (charge once every 3 months). This will extend
the life of your lithium battery.
FCC STATEMENT
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
The Bluetooth® word mark and logos are registered
trademarks owned by Bluetooth SIG, Inc. and any use of
such marks by SKL Marketing Inc. is under license. Other
trademarks and trade names are those of their
respective owners.
PTG INT’L
Loading...