Quick Start Guide
(External Preview Version)
© 2016 PSP Security Co. Ltd. All rights reserved
Alarm
Jack
A. Establishing Connection
1. The following peripherals are required to operate AccuFACE:
12 VDC power supply with at least 2 Amps output
Ethernet cable
Tamper
DC 12V Power, 2Amp
Ethernet
o Left: Ground
o Right: 12V DC
2. Attach the mounting bracket to the back of AccuFACE to keep tamper
alarm off. Installation height of 120cm (distance from ground to
AccuFACE’s camera) is recommended.
3. Connect AccuFACE to your Local Area Network (LAN) using the Ethernet
cable.
4. Connect the 2-pin power terminal block to the system and be careful
with the polarity. Power up the system.
AccuFACE® EFR-T3 Series Quick Start Guide
Version 1.0
B. Standalone Mode Enrollment
In Standalone Mode, you can use touch screen to perform enrollment and
system configuration without the need of network connection.
1. Once powered up, AccuFACE shows below screen.
Current date and
time
Standalone Mode
button
Current Operating
Mode: 1:N
Identification
(1 to Many)
Keypad to enter
User ID for 1:1
verification
2. Press the Standalone Mode button, then enter Root Passcode
(default:XXXXXX, followed by Enter Key) to enter.
Default Root
Passcode: 1234
3. Once authenticated, point to the “User” page to start “User Manager”.
Select “User” page
Start “User
Manager”
AccuFACE® EFR-T3 Series Quick Start Guide
Version 1.0
4. Select the Enrollment page and fill in user information. Steps are:
Click button
to open on-screen
keyboard for user
ID/name editing
“Enrollment” page
Enter User ID from on-screen keypad or badge a card to read card ID
User Name and Alias ID are optional
For security purpose, it is suggested to enroll at least one Root User
For user who wears glasses, check “Wear Glasses”
Click “Start Enrollment” to start
5. The system now goes into Enrollment mode and start a 3-second
countdown. User is required to stand in front of AccuFACE and position
the face properly.
When face is locked in green square
box, enrollment proceeds
Operating
distance:
45~70 cm
6. During the enrollment, gently tile the face up and down, then gently
move closer and farther. If you wear glasses, you will be asked to
remove the glasses half way through the enrollment.
7. Follow the screen message and voice instructions to complete the
enrollment.
AccuFACE® EFR-T3 Series Quick Start Guide
Version 1.0
C. Quick Recognition Test
1. Only enrolled user can be recognized. If user has not been enrolled,
please refer to Section B and perform user enrollment.
2. If AccuFACE is set to 1:N mode, simply approach to the machine to start
authentication. Like enrollment, recognition will occur only when the
face is locked at Green square box. User who is identified will be
granted with a green check and a voice welcome.
Green bar shows
how close the user
to be identified
Passed
score
Enrolled
picture
with
user info
3. If AccuFACE is set to 1:1 mode, user must scan a card or enter user ID
from the touch screen first before AccuFACE could perform facial
recognition.
Under 1:1 mode,
enter User ID
and Enter key to
start verification
4. If face is not locked at green square box, please move a little closer or
farther from AccuFACE and gently nod head up and down. Recognition
should occur.
AccuFACE® EFR-T3 Series Quick Start Guide
Version 1.0
D. Standalone Mode Configurations
1. Press the Standalone Mode button, and enter root passcode to enter
Standalone Mode. If a root user is already registered, you need the root
user face to be verified before entering.
2. Select the Settings page, then press “Configurations” button
Select “Settings” page
Press
“Configurations”
3. Configurations are divided into multiple pages, for instance, you can
configure operating mode (1:N or 1:1 mode) and recognition threshold
at Facial Recognition page.
Adjust Threshold of
facial recognition if
necessary
Select Operating
Mode: 1:N or 1:1
here
4. Press “Submit” button for the changes to take effect.
5. Then press the upper-right arrow to leave Standalone Mode.
Press to leave
Standalone Mode
AccuFACE® EFR-T3 Series Quick Start Guide
Version 1.0
here
E. Remote Configurations
1. By default AccuFACE gets an IP address automatically (with DHCP
protocol), you can find the address at Status page.
Find IP address
2. Open Web browser from your computer and connect to IP address
(192.168.1.154 in this example). Then the authentication screen should
be prompted. Default username is “admin” and password is
XXXXXXXX.
3. Once authenticated, you can see below System Status page. You can
view log transactions by clicking “Log”, or access configuration pages by
clicking “ADVANCED”.
.
View log
transactions here
Click ADVANCED
for configuration
pages
4. Similar with Standalone Mode, configurations are divided into multiple
pages, for instance, you can configure operating mode (1:N or 1:1
mode) and recognition threshold at Facial Recognition page.
Select Operating
Mode: 1:N or 1:1
here
Adjust Threshold of
facial recognition
here
AccuFACE® EFR-T3 Series Quick Start Guide
Version 1.0
F. More
Loading...