Psion LFAH1 User Manual
USER MANUAL
RFID Module LF-AH1-A1
PSION TEKLOGIX - Company confidential
Author: Philippe PORTE
File: DPD A00029 A30.doc
Date: 5/12/05
Page: 1 / 16
Ref: DPD A00029 A30
USER MANUAL
RFID Module LF-AH1-A1
Author: Philippe PORTE
File: DPD A00029 A30.doc
Date: 04/05/05
Pages: 16
Reference: DPD A00029 A30
Revision Date Prepared by Verify by Validated by
A30 04/05/05
Philippe PORTE Pierre BONNEFOY
Rob Vandervecht
PSION TEKLOGIX
Printing date: 12/05/2005 14:35:00
USER MANUAL
RFID Module LF-AH1-A1
PSION TEKLOGIX - Company confidential
Author: Philippe PORTE
File: DPD A00029 A30.doc
Date: 5/12/05
Page: 2 / 16
Ref: DPD A00029 A30
TABLE OF CONTENTS
1. SCOPE OF DOCUMENT .................................................................................. 3
TERMINOLOGY................................................................................................ 3
2.
3.
UPDATING OF DOCUMENT ............................................................................ 3
4. ENVIRONMENT ................................................................................................ 3
4.1. DOCUMENTS AND REFERENCE ELEMENTS ..................................................................................... 3
5. RFID MODULE INSTALLATION....................................................................... 4
5.1. REMOVING THE END-CAP AND BACK PLATE.................................................................................. 4
5.2. WHAT’S INSIDE ............................................................................................................................ 5
5.3. SHUTTING OFF POWER ............................................................................................................... 5
5.4. INSTALLING THE RFID MODULE LF-AH1-A1................................................................................. 6
5.5. RFID READING AREA................................................................................................................... 8
6. SOFTWARE PACKAGE ................................................................................... 9
6.1. RFID DEMO INSTALLATION .......................................................................................................... 9
6.2. RFID DEMONSTRATION ............................................................................................................. 11
6.3. RFID PERFORMANCE ................................................................................................................ 14
7. RFID REGULATORY INFORMATION............................................................ 15
USER MANUAL
RFID Module LF-AH1-A1
PSION TEKLOGIX - Company confidential
Author: Philippe PORTE
File: DPD A00029 A30.doc
Date: 5/12/05
Page: 3 / 16
Ref: DPD A00029 A30
1. SCOPE OF DOCUMENT
This document describes the method to install the RFID Module LF-AH1-A1 in the Psion
Teklogix WORKABOUT PRO and to install the preliminary software package.
2. TERMINOLOGY
3. UPDATING OF DOCUMENT
Version Evolutions Author Date
A00 Creation Philippe PORTE 12/01/05
A10 Up date Philippe PORTE 09/02/05
A20 Antenna LF-A1, FCC and CE Philippe PORTE 02/05/05
A30 New demo software Philippe PORTE 04/05/05
4. ENVIRONMENT
4.1. Documents and reference elements
Document Reference Version Date
USER MANUAL
RFID Module LF-AH1-A1
PSION TEKLOGIX - Company confidential
5. RFID MODULE INSTALLATION
Easily installable expansion modules for the WORKABOUT PRO allow you to customise this
hand-held to meet your specific mobile computing requirements. This chapter outlines how to
install the RFID Module LF-AH1-A1 (this module is composed of one RFID Coupler LF-AH1
and one RFID Antenna LF-A1).
5.1. Removing the End-Cap and Back Plate
To install a module, you’ll need to remove the end-cap and back plate on the WORKABOUT
PRO. This is a simple process of unfastening four screws on the end-cap and six screws on
the back plate.
Author: Philippe PORTE
File: DPD A00029 A30.doc
Date: 5/12/05
Page: 4 / 16
Ref: DPD A00029 A30
5.2. What’s inside
USER MANUAL
RFID Module LF-AH1-A1
PSION TEKLOGIX - Company confidential
Author: Philippe PORTE
File: DPD A00029 A30.doc
Date: 5/12/05
Page: 5 / 16
Ref: DPD A00029 A30
5.3. Shutting OFF power
Before installing a module in the WORKABOUT PRO, all power sources must be turned off.
• Remove the batteries. If your unit is using AC power, disconnect it.
• Remove the end-cap at the top of the WORKABOUT PRO.
• Slide the SW1401 switch to the left to shut off internal battery power.
Loading...