Psion EP10 RV3004, EP10 RV3007 Quick Start Manual

LOCATION GUIDE FOR THE
MOUNTING SCREWS

WALL MOUNTING

CONTENTS OF THE BOX

This Guide

TABLETOP INSTALLATION

.

OVER

>

1

2

CHARGER NOT ANCHORED TO THE TABLE

CHARGER ANCHORED TO THE TABLE

Set the charger down on its rubber feet as shown:

Attach 2 Anchoring Screws to the Tabletop

Attach Charger to Anchoring Screws

See location guide, on the previous panel, for the positions of
the screws and the size of the screwheads.

Lower the keyhole slots on the base of the charger over the
screwheads. Then push the charger backwards until it clicks
into place.

WALL MOUNTING

TABLETOP MOUNTING

1

Attach the Bracket to the Wall

Attach the bracket to the wall, as shown below, using anchors
that are suitable for the wall type. See the location guide on
the next panel for the positioning of the anchors.

2

Attach the Charger to the Bracket

Lower the keyhole slots on the base of the charger over the
tabs on the bracket. Then push the charger towards the back
of the bracket until it clicks into place.

4-SLOT CHARGER (RV3004)

WALL BRACKET - 4-SLOT CHARGER
(RV3007)

This Guide

March30, 2011
PN 8000233.A

ISO 9001 Certified
Quality Management System

EP10

™

RV3004

CHARGER SPARE BATTERY
4 SLOT

RV6009

WALL BRACKETY
BATTERY CHARGER - 4 SLOT
4 SLOT

QUICK
START
GUIDE

Rear view of bracket

Underside of charger

3.0 in

[75 mm]

2.0 in

[51 mm]

Back

Front

Mounting holes

1. Down

2. Back

0.06 in [1.6 mm]

0.4 in

[10 mm]

0.10 in [2.5 mm]

Tabletop

1.9 in

[48 mm]

1.4 in

[35 mm]

0.9 in

[23 mm]

1.4 in

[37 mm]

Cross-section of mounting tab

Charger

Power supply with cable and DC plug

Wall bracket
(wall anchors not provided)

1. Down

2. Back

1.9 in

[48 mm]

1.4 in

[35 mm]

2.0 in

[60 mm]

1.8 in

[45 mm]

March30, 2011
PN 8000233.A

ISO 9001 Certified
Quality Management System

EP10

™

RV3004

CHARGER SPARE BATTERY
4 SLOT

RV6009

WALL BRACKETY
BATTERY CHARGER - 4 SLOT
4 SLOT

QUICK
START
GUIDE

0.23 in

[5.8 mm]

ALSO NEEDED - NOT INCLUDED IN RV3004

External power cable - ordered separately (varies depending on region)

Charge LED Behaviour Description

Off No battery detected.

Solid Green Battery charging complete.

Flashing Green Charge in progress.

Flashing Yellow Battery is not charging due

to out-of-temperature conditions.

Solid Red Unable to read battery or non Psion battery.

0 °C to 40 °C
32 °F to 104 °F

Each charge compartment has a charge LED.

April 21, 2011
PN 8000233.A

ISO 9001 Certifi ed
Quality Management System

8000233

BATTERY CHARGE INDICATOR

CONNECT THE CHARGER TO
EXTERNAL POWER

CHARGE

2

Charge EP10 Battery for 3 Hours to 4 Hours

3 hours to 4 hours

Note: Full battery performance is only reached after the fi rst few

charge/discharge cycles.

1

Insert an EP10 Battery into the Charger

Slide an EP10 battery, as shown, into each charge
compartment until the battery touches the base of the
charge compartment.

1

Connect the Power Supply to the Charger

Insert the DC plug from the power supply into the socket
on the back of the charger:

2

Connect the Power Supply to an External
Power Source

3

For a Wall-Mounted Charger...

Place the power supply in the holder and route the cables as
shown here:

Power supply

To external
power

Rear view of charger on bracket

DC socket

Rear view of charger

DC socket

DC plug

To power supply

EP10

™

RV3004

CHARGER SPARE BATTERY
4 SLOT

RV3007

WALL BRACKET
BATTERY CHARGER - 4 SLOT

QUICK
START
GUIDE

Charge LED

© Copyright 2011 by Psion Inc.
Psion, Psion Teklogix, and EP10 are trademarks of Psion Inc. Other product names
mentioned in this document are trademarks or registered trademarks of other hardware,
software, or service providers and are used herein for identifi cation purposes only.