-
M
ORPHO
™ RAPID Q
UICK USER’S GUIDE
MO R P H O RA P ID QU I C K
MorphoRapID™ Specifications
US E R ’S GU I D E
1.MorphoRa pID™ Sp e c i fication s
Technical Specifications
Display
Sensor
Input/Output USB 2.0
Power PSA 15R-050P Model
Temperature Range
Humidity
• Size: 3.7"
• VGA Display: 640 x 480 high resolution LCD Touch Panel
• 65536 Full-Colors
• 500 DPI in X and Y axis
• 8-bit gray scale
• Acquisition area 21 x 21 mm (0,8 x 0,8 ")
- Input: AC 100-240 V~ 50-60 Hz 0.5 A
- Output: DC 5.0 V 3.0 A
• Operating +0°C to 45°C
• Storage -20°C to 70°C
• Operating 15% < RH < 95% non-condensing
• Storage < 95%
Weight
Dimensions 89 x 126 x 185 mm
NOTE
0000025754-07 - O
S
AGEM SÉCURITÉ DOCUMENT
CTOBER
800 g
A removable power cord connects the MorphoRapID™ to the mains supply - Its socket
outlet shall be near the MorphoRapID™ and shall be easily accessible.
2008 1
- R
EPRODUCTION AND DISCLOSURE PROHIBITED
.
or modifications not expressly approved by the party responsible for the
M
ORPHO
™ RAPID QUICK U
SER’S GUIDE
International Standards
2.Inte rn a t ional St a n d ards
The MorphoRapID™ terminal complies with both European and U.S. standards as follows:
Region Standards
Europe
EMC Directive 89/336/EEC: EN55022 (1994) / EN55024 (1998)
Low voltage Directive 73/23/EEC amended by 93/68/EEC: EN60950
(2000)
USA
FCC part 15 Class A digital device requirements
USA
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required to correct the interference at
his own expense.
Radiation Exposure Compliance
This product complies with the FCC RF exposure limits for an uncontrolled environment. For continued compliance, the product must not be held closer than 20 cm from the rest of the body. This product must not be
used in a holster or on a belt-clip.’
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Canada
This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. When using the 802.11 radio option, to prevent radio interference, this device is intended to be operated indoors and away from windows to provide maximum shielding. Equipment (or its transmit antenna) that
is installed outdoors is subject to licensing.
Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur
du Canada. En cas d’utilisation du module radio 802.11, afin d'éviter toute interférence radio avec le service
autorisé, l'appareil doit être utilisé à l'intérieur, tout en étant éloigné de toute fenêtre afin de garantir le maximum de protection. Si cet équipement (ou son antenne émettrice) est installé à l'extérieur, il est alors soumis à
licence.
0000025754-07 - O
S
AGEM SÉCURITÉ DOCUMENT
CTOBER
Changes
WARNING
2008 2
- R
EPRODUCTION AND DISCLOSURE PROHIBITED
compliance could void the user’s authority to operate the equipment.
.
M
ORPHO
™ RAPID QUICK U
SER’S GUIDE
MorphoRapID™ Specifications
Model Option
Morpho RapID 1100 Standard version
Morpho RapID 1100 W WiFi
Morpho RapID 1100 G GSM/GPRS/3G
Morpho RapID 1100 WG WiFi - GSM/GPRS/3G
0000025754-07 - O
S
AGEM SÉCURITÉ DOCUMENT
CTOBER
2008 3
- R
EPRODUCTION AND DISCLOSURE PROHIBITED
.
products that could damage the
art (cracks may appear on body or
M
ORPHO
™ RAPID QUICK U
3.Clean i n g
Clean the MorphoRapID™ body, screen and biometric sensor with a dry, non-abrasive, lint-free cloth and
only with a cleaning product recommended by Sagem Sécurité.
During periods of intense activity, the sensor should be cleaned as soon as smears are visible on-screen.
SER’S GUIDE
Cleaning
WARNING
MorphoRapID™ body or sensor p
prism).
Examples of corrosive chemicals to be avoided:
– acetone,
– ammoniac,
– benzene,
– ethanol,
– methanol,
– methylated spirit,
– petrol,
– thichlorethylene.
Avoid using any alcohol or by-
0000025754-07 - O
S
AGEM SÉCURITÉ DOCUMENT
CTOBER
2008 4
- R
EPRODUCTION AND DISCLOSURE PROHIBITED
.
Loading...