Psiber CM400 User Manual [ml]

CableMaster

CM400

Testing:
A. Plug the wire into the correct Test Port, Ethernet to RJ45
B. Plug the opposite end into the Main Remote
C. Press Network Button
D. The LCD Display reports wire condition, Pass/Fail
E. To turn off, press O/ID Button

Toning:
A. With the unit turned OFF, hold down the TONE button until

LCD illuminates
B. To select a tone cadence, press the TONE button repeatedly to step through
the four cadence options: HI, LO, Hi-Lo1, and Hi-Lo1. Stop when you reach the
option you want. The option you select determines the cadence sent from the
main tester, through the cable, and picked up by the tone tracer probe.
C. Press the appropriate cable type button (voice, video, or data) to select a
cable for the tone signal

* Note: Tone is detected by a tone tracer probe

Features:

Testing: CM400 shows Opens, Shorts, Miswires, Split Pairs, PASS and

FAIL results quickly.

Toning: CM400’s built-in tone generator is a fl exible and function-packed
tone generator. Its confi gurable signal can be generated to fi nd and fi x the
position on any type of cable - either exposed or hidden, in ceilings or
behind walls.

Option: CM400 is supported by (1-19) wiremapping ID locators (Network/Coax).

Quick Start Guide

Kurzanleitung

Guide de Démarrage Rapide

CableMaster

CM400

1

3

2

5

4

6

7

CableMaster

CM400

Testing:
A. Plug the wire into the correct Test Port, Ethernet to RJ45
B. Plug the opposite end into the Main Remote
C. Press Network Button
D. The LCD Display reports wire condition, Pass/Fail
E. To turn off, press O/ID Button

Toning:
A. With the unit turned OFF, hold down the TONE button until

LCD illuminates
B. To select a tone cadence, press the TONE button repeatedly to step through
the four cadence options: HI, LO, Hi-Lo1, and Hi-Lo1. Stop when you reach the
option you want. The option you select determines the cadence sent from the
main tester, through the cable, and picked up by the tone tracer probe.
C. Press the appropriate cable type button (voice, video, or data) to select a
cable for the tone signal

* Note: Tone is detected by a tone tracer probe

Features:

Testing: CM400 shows Opens, Shorts, Miswires, Split Pairs, PASS and

FAIL results quickly.

Toning: CM400’s built-in tone generator is a fl exible and function-packed
tone generator. Its confi gurable signal can be generated to fi nd and fi x the
position on any type of cable - either exposed or hidden, in ceilings or
behind walls.

Option: CM400 is supported by (1-19) wiremapping ID locators (Network/Coax).

English

Quick Start Guide

CableMaster

CM400

1

3

4

2

5

Button Function
1 LCD Display 5 Tone Mode
2 Voice Mode 6 On/Off and ID Mode
3 Video Mode 7 Main Unit Remote
4 Data Mode (RJ11/RJ12, RJ45)

6

7

English

A. Plug the wire into the correct Test Port, e.g. Ethernet to RJ45
B. Plug the opposite end into the Main Remote
C. Press Network Button
D. The LCD Display reports wire condition, Pass/Fail
E. To turn off, press O/ID Button

Toning:

A. With the unit turned OFF, hold down the LENGTH/TONE button until LCD

illuminates

B. To select a tone cadence, press the LENGTH/TONE button repeatedly to

step through the four cadence options: HI, LO, Hi-Lo1, and Hi-Lo 2. Stop
when you reach the option you want. The option you select determines
the cadence sent from the main tester, through the cable, and picked up
by the tone tracer probe*.

C. Press the appropriate cable type button (voice, video or data) to select a

cable for the tone signal

* Note: Tone is detected by a tone tracer probe (optional)

Features:

Testing: CM400 shows Opens, Shorts, Miswires, Split Pairs, PASS and
FAIL results quickly.
Toning: CM400`s built- in tone generator is a flexible and function- packed
Tone generator. Its configurable signal can be generated to find and fix the
position on any type of cable – either exposed or hidden, in ceilings or
behind walls.

Length: CM400 determines the length (in feet or meters) of an entire cable
and/ or individual wire pairs within the cable.

Option: CM400 is supported by (1-19) wiremapping ID locators (Network/
Coax) and (1-8) testing/ID remotes (Network/Telephone).

CableMaster

CM400

Testing:
A. Plug the wire into the correct Test Port, Ethernet to RJ45
B. Plug the opposite end into the Main Remote
C. Press Network Button
D. The LCD Display reports wire condition, Pass/Fail
E. To turn off, press O/ID Button

Toning:
A. With the unit turned OFF, hold down the TONE button until

LCD illuminates
B. To select a tone cadence, press the TONE button repeatedly to step through
the four cadence options: HI, LO, Hi-Lo1, and Hi-Lo1. Stop when you reach the
option you want. The option you select determines the cadence sent from the
main tester, through the cable, and picked up by the tone tracer probe.
C. Press the appropriate cable type button (voice, video, or data) to select a
cable for the tone signal

* Note: Tone is detected by a tone tracer probe

Features:

Testing: CM400 shows Opens, Shorts, Miswires, Split Pairs, PASS and

FAIL results quickly.

Toning: CM400’s built-in tone generator is a fl exible and function-packed
tone generator. Its confi gurable signal can be generated to fi nd and fi x the
position on any type of cable - either exposed or hidden, in ceilings or
behind walls.

Option: CM400 is supported by (1-19) wiremapping ID locators (Network/Coax).

Deutsch

Kurzanleitung

CableMaster

CM400

1

3

4

2

5

Funktionstasten

1. LCD Display

2. Sprachmodus

3. Videomodus

4. Datenmodus

5. Tonmodus

6. Ein/Aus und ID-Modus

7. Remoteeinheit

(RJ11/RJ12, RJ45)

6

7

Deutsch

A. Schließen Sie ein Kabelende an die RJ45 Buchse am Hauptgerät an.
B. Schließen Sie das andere Ende an die RJ45 Buchse der Remoteeinheit an.
C. Drücken Sie die Taste Netzwerk.
D. Auf dem Bildschirm wird das Ergebnis mit Pass/Fail und der Verdrahtungs-

plan angezeigt

E. Zum Ausschalten des Gerätes drücken Sie die Taste O/ID

Tonverfolgung:

A. Bei ABGESCHALTETEM Gerät halten Sie die Taste TON solange gedrückt,

bis der Bildschirm aufleuchtet

B. Zum Auswählen eines von vier möglichen Tonmustern drücken Sie die

Taste TON wiederholt, bis das gewünschte Tonmuster angezeigt wird (HI,
LO, Hi-Lo1 und Hi-Lo2). Vom Hauptgerät wird das gewählte Tonsignal auf
das Kabel gesendet und kann nun mit dem Tonverfolger geortet werden

C. Drücken Sie die entsprechende Taste für den Kabeltyp (Voice - Sprache,

Video oder Data - Daten), der mit diesem Tonsignal beaufschlagt werden
soll.

* Hinweis: Der Ton wird mit einem Tonverfolger geortet (optionales Zubehör).

Funktionsmerkmale:

Test: Im Handumdrehen zeigt der CM400 Unterbrechungen, Kurzschlüsse,
Verdrahtungsfehler, Split Pair-Fehler, PASS und FAIL Ergebnisse auf dem
Bildschirm an.
Tonverfolgung: Der integrierte Tongenerator des CM400 kann flexibel auf die
Erzeugung von vier verschiedenen Tonmustern konfiguriert werden. Über das
Tonsignal ist es möglich, jedes Kabel zu orten und dessen Verlauf zu verfol­gen – ob freiliegend oder unter Putz, in der Decke oder hinter der Wand.

Option: Zur Verwendung mit dem CM400 können (1 – 19) Fernerkennungen
(Netzwerk/Koaxial) zur Kabelerkennung und (1 – 8) Fernerkennungen (Netz­werk/Telefon) zum Test/ID separat bestellt werden.

CableMaster

CM400

Testing:
A. Plug the wire into the correct Test Port, Ethernet to RJ45
B. Plug the opposite end into the Main Remote
C. Press Network Button
D. The LCD Display reports wire condition, Pass/Fail
E. To turn off, press O/ID Button

Toning:
A. With the unit turned OFF, hold down the TONE button until

LCD illuminates
B. To select a tone cadence, press the TONE button repeatedly to step through
the four cadence options: HI, LO, Hi-Lo1, and Hi-Lo1. Stop when you reach the
option you want. The option you select determines the cadence sent from the
main tester, through the cable, and picked up by the tone tracer probe.
C. Press the appropriate cable type button (voice, video, or data) to select a
cable for the tone signal

* Note: Tone is detected by a tone tracer probe

Features:

Testing: CM400 shows Opens, Shorts, Miswires, Split Pairs, PASS and

FAIL results quickly.

Toning: CM400’s built-in tone generator is a fl exible and function-packed
tone generator. Its confi gurable signal can be generated to fi nd and fi x the
position on any type of cable - either exposed or hidden, in ceilings or
behind walls.

Option: CM400 is supported by (1-19) wiremapping ID locators (Network/Coax).

France

Guide de Démarrage Rapide

CableMaster

CM400

1

3

4

2

5

Touches

1. Ecran LCD

2. Mode Voix

3. Mode Vidéo

4. Mode Données

5. Mode Tonalité

6. Marche/Arrêt et Mode ID

7. Unité Distante

(RJ11/ RJ12, RJ45)

6

7

France

A. Branchez une extrémité du câble sur le port RJ45 du testeur principal.
B. Branchez l’autre extrémité du câble sur l’unité distante.
C. Pressez la touche Network (Réseau).
D. L’écran affichera le résultat : Pass/Fail (Succès/Echec), schéma de câblage
E. Pour éteindre le testeur, pressez la touche O/ID.

Tonalité :

A. Le testeur éteint, tenez la touche TONE (Tonalité) enfoncée, jusqu’à l’écran

s’allume.

B. Pour sélectionner la tonalité, pressez la touche TONE plusieur fois et faites

votre choix entre quatre
tonalités : HI, LO, Hi-Lo1 et Hi-Lo2. Arrêtez, quand l’option désirée s’affiche.
Le testeur émettra la tonalité choisie sur le câble pour le dépister avec le
dépisteur de tonalité.

C. Pressez la touche appropriée au type de câble (voice - voix, video - vidéo,

ou data - données) pour transmettre la tonalité.

* Note : La tonalité sera détectée par un dépisteur de tonalité.((Accessoires

optionnels)

Caractéristiques :

Test : CM400 affiche rapidement les résultats de test: courts-circuits, circuits
ouverts, mauvais câblage, paires séparées (Split Pairs), Pass/Fail (Succès/
Echec).

Tonalité : Le générateur de tonalité incorporé dans le CM400 peut fl exible­ment être confi gurré à la tonalité désirée pour trouver la position d’un prob­lème sur chaque type de câble - si exposé ou encastré dans des plafonds ou
des murs.

Option : Le CM400 est soutenu par des (1-19) sondes à distance pour localiser
les câbles par l’identification (lID) de câbles (Réseau/Coaxial) et par des (1-8)
sondes à distance pour test/ID (Réseau/Téléphone).

Psiber US:

Psiber Data Sytems Inc.

7075-K Mission Gorge Road

San Diego, CA 92120

Phone: [phone]

e-mail: [e-mail]

www.psiber.com

Psiber Europe:

Psiber Data GmbH

Felix-Wankel-Str. 4

82152 Krailling

Germany

Phone: [phone]

e-mail: [e-mail]

www.psiberdata.com

Psiber Data Pte. Ltd.:

3 Science Park Drive

#03-09 The Franklin

Singapore Science Park 1,

Singapore 118223

Phone: [phone]

e-mail: [e-mail]

www.psiberdata.com

For technical information and support please

contact the Psiber Ofce in your country.

www.psiberdata.com