PSC Scanning QuickScan 6000, QuickScan 6000 plus User Manual

H

ANDHELD LASER SCANNER

U

I

NTERF ACE

NIVERSAL

P

ROGRAMMING

W

EDGE

PSC Scanning, Inc.
959 Terry Street
Eugene, Oregon 97402-9120
Telephone: [phone]
Toll Free: [phone]
Fax: [phone]

PSC and the PSC logo are registered trademarks of PSC INC.

This manual and the procedures described in it are copyrighted, with all rights
reserved. Under copyright law, this manual may not be copied in whole or part
without prior written consent from PSC Scanning, Inc. The same proprietary and
copyright notice must appear on any permitted copies as appears on the original. This
exception does not permit copies to be made for others, whether or not sold. Under
the law, copying includes translating into another language or format including
electronic media.

Disclaimer

Reasonable measures have been taken to ensure that all information contained
in this manual is complete and accurate. However, PSC Scanning, Inc. reserves
the right to change any specification at any time without prior notice.

UNIVERSAL WEDGE INTERFACE PROGRAMMING

For your convenience, this guide provides minimal configuration and op­tion settings for your scanner's Universal Wedge interface. For more de­tailed programming information and features, reference the QuickScan
6000/6000 Plus Universal Wedge Programming Guide (R44-1548), avail­able from your dealer.

DISCONNECTING/CONNECTING THE INTERFACE (I/F) CABLE

To disconnect the I/F cable at the scanner, insert a bent paper clip or
.050" hex driver into the opening marked CABLE RELEASE as shown in
Figure 1, and push inward. Once the connector latch is released, con­tinue to hold in on the latch while carefully pulling the cable free.
Connect the scanner to your system using ONLY the proper PSC ap­proved QuickScan 6000/6000 Plus I/F cable.

WARNING

Connection using an unapproved cable can result in damage
to the scanner. QuickScan 6000/6000 Plus cables can be
identified by a cable I.D. code printed on a white label, ap­proximately 1" in length, attached to them.

Paper Clip

Approved
QuickScan 6000/6000+ Cable

Latch

Overmolding

DO NOT use
unapproved
cables

Interface

Connector

e
s
a

le

e

R

le
b
a

C

Figure 1. Disconnecting/Connecting the QuickScan 6000/6000 Plus I/F Cable

R44-1549

1

RETURN TO FACTORY CONFIGURATION

If, during a programming session, you wish to reset the scanner's con­figuration to its original factory settings, scan the RETURN TO FACTORY
SETTINGS label below. Use this label ONLY IF NECESSARY, since it will
reset any changes made to this interface during any previous program­ming session.

RETURN TO FACTORY SETTINGS

*/+$*

NOTE

When this feature is scanned, return to factory set­tings will take about five seconds to complete. The
scanner will sound a tone at its conclusion.

P

ROGRAMMING MODE

The scanner must be placed in Programming Mode before its configura­tion can be altered using the barcodes in this guide. Enter Programming
Mode by scanning the START label found at the bottom of each page.
The scanner's green light will flash continuously, indicating the scanner is
in Programming Mode.

While in Programming Mode, the scanner will recognize only specially
formatted programming barcode labels like those contained in this guide,
and will not decode barcode labels of any other type. Scan all program­ming barcode labels needed to set the scanner's features to the desired
settings. The scanner will beep after each barcode label is scanned, indi­cating that the setting has been stored in memory. The scanner will emit
a rejection tone if a scanned barcode programming label isn't valid.
To exit Programming Mode and save all changes made during the pro­gramming session, scan the END label located at the bottom of each
page. The scanner will return to normal operation.

Disconnecting power during Programming Mode will cause the scanner
to return to its previous settings.

QuickScan 6000/6000 PLus

Universal Wedge Interface Programming

2

PC KEYBOARD WEDGE INTERFACE SELECTION

The default communication mode (factory settings) is Keyboard Wedge for PC AT
(keyboard I.D. 11). Use the codes on this page to activate keyboard-wedge mode and
to select the I.D. corresponding to your computer or terminal (reference Connectivity
Guide R44-1040 or call PSC Customer Support):

*AEU*

KEYBOARD-WEDGE MODE ACTIVATED

Consult the list of connections listed in Connectivity Guide R44-1040 (or
call PSC Customer Support) and enter the I.D corresponding to your
computer or terminal using this barcode pad.

*AG1*

1

*AG4*

4

*AG7*

7

*AG2*

2

*AG5*

5

*AG8*

8

*AG3*

3

*AG6*

6

*AG9*

9

*AG0*

0

Use the next pages to adjust some general parameters of Universal Wedge
communication.

*$%/*

START END

*$+$*

R44-1549

3

END OF M

One of the characters below can be systematically emulated by the scanner as the
end of message character:

ESSAGE CHARACTER

*DP7* *DP3*

RETURN*

(DEFAULT)

FIELD EXIT

*DP5* *DP1*

ENTER TAB +

*DP6* *DP2*

CR/LF ; FEED ; SEND LF

*DP4* *DP0*

FIELD ADVANCE

NO CHARACTER

U

PPER/LOWER CASE OPTIONS

Use one of these codes to inform the scanner of the state of your keyboard:

*DH4* *DHI*

*$%/*

UPPER CASE/CAPS*

(DEFAULT)

START

QuickScan 6000/6000 Plus

4

Universal Wedge Interface Programming

LOWER CASE/SMALL

*$+$*

END

T

IME-OUT BETWEEN CHARACTERS

The insertion of a time-out between each character can sometimes avoid the
occurrence of errors during fast transmission speeds (especially with PS/2, or when
DOS and BIOS are very busy).

(I

NTERCHARACTER DELAY

)

*G00* *G14*

0 ms*

(DEFAULT)

20 ms

*G05* *G32*

5 ms 50 ms

*G0A* *G64*

10 ms 100 ms

T

RANSFORMATIONS

Use these codes to transform labels to the desired format before transmission to the
host terminal.

*GHA* *GHO*

UPC TRANSMITTED AS EAN*

(DEFAULT)

UPC TRANSMITTED AS UPC

*GHS* *GHU*

UPC E TRANSMITTED AS UPC E*

R44-1549

(DEFAULT)

UPC E TRANSMITTED AS UPC A

*$+$**$%/*

ENDSTART

5

Asia Pacific

PSC Hong Kong
Hong Kong
Telephone: [852]-2-584-6210
Telefax: [852]-2-521-0291

Italy

PSC S.r.l.
Vimercate (MI), Italy
Telephone: [phone]
Telefax: 039/6859496

Australia

PSC Asia Pacific Pty Ltd.
North Ryde, Australia
Telephone: [61]0(2)9878 8999
Telefax: [61]0(2)9878 8688

France

PSC Sarl
LES ULIS Cedex, France
Telephone: [33].1.64.86.71.00
Telefax : [33].1.64 46.72.44

Germany

PSC GmbH
Darmstadt, Germany
Telephone: + 49 (0) 61 51/93 58 - 0
Telefax: + 49 (0) 61 51/93 58 58

Japan

PSC Japan K.K.
Shinagawa-ku, Tokyo, Japan
Telephone: [phone]
Telefax: 81 (0)3 3491 6656

Latin America

PSC S.A., INC.
Miami, Florida, USA
Telephone: [phone]
Telefax: [phone]

United Kingdom

PSC Bar Code Ltd.
Watford, England
Telephone: [phone]
Telefax: 44 (0) 1923 809 505

Corporate Headquarters

675 Basket Road
Webster, NY 14580-9787
Telephone: [phone]
Toll Free: [phone]
Telefax: [phone]

Printed on recycled paper

© 1998 PSC

INC.

www.pscnet.com

R44-1549 (Rev. B)

PSC Scanning, Inc.

959 Terry Street
Eugene, OR 97402-9150
Telephone: [phone]
Toll Free: [phone]
Telefax: [phone]

PRINTED WITH

SOY INK

Printed in USA 8/98