PSB CW600E Specification Sheet
Be Heard, Not Seen
PSB CustomSound In-Wall Speaker System
CW600E - Enclosed In-Wall System
In-wall speakers confront special acoustic challenges. Limited
interior space connes their effective enclosure volume, while
comparatively imsy partition construction is no substitute for a true
loudspeaker cabinet. There’s rarely enough in-wall volume for real
bass extension, and the same factor dooms most in-walls to being
both unusually power hungry and dynamically limited.
For the PSB CustomSound premium in-wall system, the CW600E,
the solution is a design that utilizes its own fully engineered
loudspeaker enclosure. Derived from the highly acclaimed Platinum
T6 tower, the CW600E incorporates a tall, narrow, highly braced,
fully enclosed, wooden enclosure just four inches deep that ts
fully within standard, 16-inch-studded construction. The CW600E’s
dual 6 1/2-inch (165mm) high-power woofers employ incredibly stiff
berglass cones and higher mass to optimize them to their enclosure
volume. The same MTM (midrange-tweeter-midrange) array found
in the acclaimed PSB Platinum T6 tower, and a specially optimized
crossover match system balance to the PSB Platinum Series
while extending bass response. The result is superb, “Platinum-
class” clarity and dynamics, with a highly dispersive “sweet spot”
so wide and tall that even large home-theater audiences will enjoy
maximum denition of movie sound and music alike. A “dog-leg”
mounting scheme assures fast, fool-proof and easy mounting. The
PSB CustomSound CW600E design nally settles the longstanding
conict between sound and design.
30 13/16"
782mm
31 3/4"
807mm
14"
356 mm
3 3/4"
86mm
12.875"
327mm
CW600E - Enclosed In-Wall System
• “Platinum-Class” In-Wall performance
• Five Driver, 3-way system utilizes Platinum T6 drivers
with stiff berglass cones and higher cone mass to
optimize them to their restricted enclosure volume
• Fully enclosed, highly braced wooden enclosure ts
within standard, 16” studded wall
• Midrange-tweeter array provides “Platinum-class”
clarity and dynamics with a highly dispersive “sweet
spot”.
Frequency Range (-6dB): 45-35,000Hz
Recommended Power: 15-200 Watts
Impedance: 6 Ohms
Sensitivity (1W (2.83V) @1m)
Anechoic Chamber: 86dB SPL
Typical Listening Room: 88dB SPL
Drivers: 2 x 6 1/2” Woofers,
2 x 3 1/2” Midranges,
1” Dome Tweeter
Overall Dimensions (W x H x D): 14 x 31 3/4 x 3 3/4”
Cut-out Dimensions (W x H): 12 7/8 x 30 13/16”
Weight: 31 lbs
Installation Notes
• The CW600E requires a full width stud bay
clear of any obstructions, pipes, wires, etc.
• Optimum mounting should place the tweeter
as close to ear level as possible.
• System should be vertical as shown.
• Wire connections are on bottom of system.
The system may be inverted if needed.
• Lift into aperture gently with two people if
possible. (System is heavy!)
• Tighten 12 “dog leg” screws with a rm
torque setting. Do not over tighten!
• Midrange and treble switches can be
adjusted to suit room acoustics and personal
taste.
• Due to the CW600E system being fully
enclosed no in-wall accoustic treatment is
required.
• System may be painted. Scufng and
priming recommended.
• See manual for more installation hints.
PSB Sp eakers rese rves the ri ght to chan ge specific ations or fe atures with out notice.
© 2005 PSB Speake rs, a divis ion of Lenb rook Indust ries Limited .
PSB is a register ed trademar k of Lenbro ok Industri es Limited. Printed in Canada 08/0 5. All righ ts reserved .
No part of this publication may be reproduced, stored or transmitted in any form whatsoever without the written permission of PSB Speakers.
869 CW600E Data
To Reach US Customer Ser vice dial 1 888 772 0000 ext 4445 or 4342
www.psbspeakers.com
1 888 772 0000
Loading...