PS AUDIO DirectStream Power Plant 12 black, DirectStream Power Plant 12 silver DSP12-Owners-Manual-V1-Rev-A.pdf

®

Owner's Reference

Instructions for Use

DirectStream Power Plant 12

DirectStream Power Plant 12

DirectStream Power Plant 12

4865 Sterling Drive Boulder, CO 80301

PH: 1 (800) PSAUDIO [e-mail] www.psaudio.com 15-059-11-1

©2018 PS Audio Inc. All rights reserved.

Rev A

®

Introduction

DirectStream Power Plant 12

Important Safety
Instructions

Heed all warnings
Follow all instructions

WARNING. TO REDUCE THE RISK OF FIRE OR ELECTRICAL SHOCK, DO NOT EXPOSE THIS APPARATUS TO
RAIN OR MOISTURE.

Clean only with a dry cloth.

Do not place ammable material on top of or beneath the component.

The PS Audio Power Plant 12 is an actively cooled component that requires adequate ventilation at all
times during operation.

Do not remove or bypass the ground pin on the end of the AC cord. All PS products ship with a
grounding-type plug. If the provided plug does not t into your outlet, consult an electrician for
replacement of the obsolete outlet.

Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus. Unplug this apparatus during lightning storms.

When making connections to this or any other component, make sure all components are powered o.
Turn o the system’s power before connecting the PS Audio component to any other component. Make
sure all cable terminations are of the highest quality.

Read these instructions

THERE ARE NO USER-SERVICEABLE PARTS INSIDE THIS PS AUDIO PRODUCT. REFER ALL
SERVICE NEEDS TO QUALIFIED SERVICE PERSONNEL.

Please contact your authorized dealer, your distributor, or PS Audio directly if you have any questions
or concerns that are not addressed in this reference manual.

PS Audio™ is a trademarks of PS Audio International Inc., and is restricted for use by PS Audio
International, Inc., its subsidiaries, and authorized agents.

4865 Sterling Drive Boulder, CO 80301 Introduction

PH: 1 (800) PSAUDIO [e-mail] www.psaudio.com 15-059-11-1

©2018 PS Audio Inc. All rights reserved.

Rev A

1

®

Introduction

DirectStream Power Plant 12

Warnings

Symbols Found on
the P12

WARNING: TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT EXPOSE THIS APPARATUS
TO DRIPPING OR SPLASHING AND NO OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES,
SHALL BE PLACED ON THE APPARATUS.

WARNING: TO REDUCE THE RISK OF ELECTRICAL SHOCK, THIS APPLIANCE MUST BE
CONNECTED TO A MAINS SOCKET OUTLET WITH A PROTECTIVE EARTH CONNECTION.

The European Union has harmonized the Mains Supply Voltage at 230V~50Hz. Previously, this
nominal voltage was 220V~ for continental Europe and 240V~ for the United Kingdom. Since the
output receptacles are Nationally Approved Mains Socket-Outlets, we have to restrict the Operator
set Output Voltage Range to 220-240V~.

Unit is shipped with the Mains Output Socket-Receptacles applicable to the country of installation as
specied by the customer. Please verify the marked Mains Supply ratings of the powered equipment
before making any AC connections. If there is a mix of marked Voltages (e.g. 220V, 230V and
240V), please set the output voltage to 230V.

Explanation of Symbols found on the DirectStream Power Plant 12

Indicates compliance with European Union Legislation for relevant safety (Low Voltage Directive
2006/95/EC) and EMC (EMC Directive 2004/108/EC) requirements.

Is intended to tell the user that parts inside the product are a risk of electric shock to persons.

Is intended to tell the user that important operating and servicing instructions are in the papers with
the appliance.

Signies that the instrument complies with European Union Waste Electrical and Electronic Equipment
Directive.

Indicates that the unit is in compliance with the European Union Reduction of Hazardous Substances
Directive.

Indicates the connector location for Ethernet connection to the network.

4865 Sterling Drive Boulder, CO 80301 Introduction

PH: 1 (800) PSAUDIO [e-mail] www.psaudio.com 15-059-11-1

©2018 PS Audio Inc. All rights reserved.

Rev A

2

®

Getting Started

DirectStream Power Plant 12

Thank You!

Welcome

Thank you for your purchasing PS Audio's DirectStream Power Plant 12 AC Regenerator. This is your
comprehensive Operator's Guide. This guide is intended to provide a full overview of the P12's functions
and capabilities. It is our intention to provide full details about the P12 and to answer any and all
questions you may have. If there is something that you feel was not covered in this guide or additional
questions for us you are welcome to reach out to us at:

[e-mail]

1 (800) PSAUDIO

We'll be happy to assist you.

The Power Plant 12 will provide regulated AC power regardless of the condition of your home’s power.
Clean, regulated AC is essential to optimize the performance of your connected equipment.

The DirectStream Power Plant removes the miles of power cables between your home and the power
station. It is the world’s rst device that is the equivalent of moving your home to within 50 feet of the
city power station.

DirectStream Power Plant 12

4865 Sterling Drive Boulder, CO 80301 Getting Started

PH: 1 (800) PSAUDIO [e-mail] www.psaudio.com 15-059-11-1

©2018 PS Audio Inc. All rights reserved.

Rev A

3

Installation
Considerations

®

Getting Started

DirectStream Power Plant 12

Location

Once your new Power Plant 12 is unpacked, you’ll need to nd a convenient place to set it.

Mounting

The Power Plant 12 should be placed with consideration of providing air circulation to the unit. If you
wish to install the P12 into your component rack, the purchase of an aftermarket, custom-designed shelf
may be necessary.

If your equipment is located a long distance from the Power Plant 12, it is preferable to use a long, heavy
gauge shielded power cable between the AC receptacle in the wall and the Power Plant. This is better
than long individual power cables between the connected components and the Power Plant 12.

Conditioners

We discourage the use of any other power conditioning equipment before or after the P12 without
considerable evaluation. A critical determination will have to be made as to whether there are any sonic
or visual shortcomings. The P12 has a signicant input and output passive lter design, and adding extra
power cables to its input or additional ltering to its output may, in fact, be undesirable.

4865 Sterling Drive Boulder, CO 80301 Getting Started

PH: 1 (800) PSAUDIO [e-mail] www.psaudio.com 15-059-11-1

©2018 PS Audio Inc. All rights reserved.

Rev A

4

®

Getting Started

DirectStream Power Plant 12

Included with the
P12

The Remote

Accessories:

• Remote Control

• Power Cable: 6ft

• Owner’s Reference

•SD Card

•Ferrite noise suppressor

1.

2.

3.

4.

5.

6.

7.

1.

The Dim button turns the P12's display on and o.

2.

MultiWave toggle button turns the MultiWave on and o.

3.

The power button puts the P12 into standby.

4.

The On button turns the unit on and brings the screen back on if dimmed.

5.

The home button and arrows allow you to navigate the on-screen menu.

6.

Clean engages the CleanWave feature.

7.

MW Strength +/- increases and decreases the MultiWave level in the setup menu.

4865 Sterling Drive Boulder, CO 80301 Getting Started

PH: 1 (800) PSAUDIO [e-mail] www.psaudio.com 15-059-11-1

©2018 PS Audio Inc. All rights reserved.

Rev A

5

®

Getting Started

DirectStream Power Plant 12

Powering on the
P12

Home Screen

Meter Screen

Once connected to power simply ip the rear power switch to the on position and allow the unit to
initialize. Once complete the unit will present the Home Screen:

After 20- seconds the display will switch to the Meter Screen:

Pressing the left or right arrows will allow you to scroll through the four dierent Meter Screens available
in the P12. See more detail about each screen on the next page.

4865 Sterling Drive Boulder, CO 80301 Getting Started

PH: 1 (800) PSAUDIO [e-mail] www.psaudio.com 15-059-11-1

©2018 PS Audio Inc. All rights reserved.

Rev A

6

®

Getting Started

DirectStream Power Plant 12

Improvement
Factor

Distortion Out

Distortion In

The Improvement Factor is an average
of the voltage output and the THD
output. It gives you a factor of how
much the AC power is improved by the
P12.

The Distortion Out is a measure of
the THD (Total Harmonic Distortion)
present in your AC output voltage.

The Distortion In is a measure of the
THD (Total Harmonic Distortion)
present in your AC input voltage.

Power

The Power Meter shows the total
wattage output from the P12.

*NOTE*

Overloading the P12 will result
in shutdown. More that an 80%
continuous load reduces the overhead
for potential peaks in the power
requirements from your audio system.
The P12 can operate continuously at
full power but you simply won't have
any extra room for potential spikes in
power draw.

4865 Sterling Drive Boulder, CO 80301 Getting Started

PH: 1 (800) PSAUDIO [e-mail] www.psaudio.com 15-059-11-1

©2018 PS Audio Inc. All rights reserved.

Rev A

7

®

Operation Guide

DirectStream Power Plant 12

Scope

Status

From the home screen press the Scope button to open the Scope window.

This is a fully functional oscilloscope that you can use to view the incoming AC waveform. Pressing
either of the arrow buttons will scroll through the voltage in, voltage out and the dierence windows.
In this way you can see the degree to which the P12's output waveform is superior to the incoming AC
Sine wave.

Here you can see the P12's overall performance data. Note how in the above image the THD output is
signicantly reduced and the output voltage is a stable 120 Volts. Press the Home button to return to
the Home screen.

4865 Sterling Drive Boulder, CO 80301 Operation Guide

PH: 1 (800) PSAUDIO [e-mail] www.psaudio.com 15-059-11-1

©2018 PS Audio Inc. All rights reserved.

Rev A

8

®

Operation Guide

DirectStream Power Plant 12

Status

Voltage

MW Strength

Pressing the Setup button on the Home screen brings you to the Setup screen:

Here you can globally adjust the output voltage for the P12. Bear in mind that the P12 will output the
same voltage from all zones. They are not individually adjustable.

Variable MultiWave Strength adjustment is available here. This feature can be enabled by pressing the
MultiWave button on the Home screen. Variable MultiWave empowers users to vary the strength of the
MultiWave output according to the needs of the equipment and the resulting performance benets. To
toggle this feature on and o simply press the Waveform Button in the Main screen.

Phase Tuning

Auto Tune

Mode

Dimmer

Phase tuning is the next adjustment. Increasing or decreasing this will move the point at which the P12
detects the incoming waveform as the wave crosses the 0 voltage point. In places where the AC power is
especially poor making small adjustments to this setting can potentially lower the THD output. The best
recommendation would be to keep this at zero unless you are seeing THD output higher than 1-2%.

Pressing the ‘auto-tune’ button will calibrate the phase setting to the optimum setting for your input
power. This only needs to be performed whenever the unit is moved to a new area to maintain optimal
performance.

The Mode setting gives you the choice of High Regulation or Low Distortion. High Regulation is
the default mode and ensures that the P12 will output the voltage very precisely at the expense of
potentially higher Distortion (THD). Low Distortion mode ensures that the P12 will output the lowest
possible distortion at the expense of more uctuations in the output voltage. Choose the option that
best suits your needs.

The Dimmer slider allow you to manually adjust the brightness of the screen. Simply move the slider left
or right to choose the brightness setting that is suitable for you.

4865 Sterling Drive Boulder, CO 80301 Operation Guide

PH: 1 (800) PSAUDIO [e-mail] www.psaudio.com 15-059-11-1

©2018 PS Audio Inc. All rights reserved.

Rev A

9

®

Operation Guide

DirectStream Power Plant 12

Setup

Outlets

Delay Mode

Pressing the right arrow pulls up the next menu of the Setup section.

The P12 has 8 total outlets in the US version, (other regions will have dierent amounts as outlet
sizes vary). The outlets are grouped into Zones that can be personalized to t your specic system
requirements.

The Power Plant 12 allows for six dierent power sequencing options. The default
setting for all zones is SWITCHED. All of these selections are only activated by the front-panel
power button.

1. SWITCHED: As the front-panel power button is engaged, any zone set to SWITCHED will
power up with no delay, and power down with a three-second delay.

2. DELAYED: As the front-panel power button is engaged, any zone set to DELAYED will
power up with a three-second delay, and power down with a zero-second delay.

3. PROGRAMMED: As the front-panel power button is engaged, any zone set to
PROGRAMMED will power up with a delay in the number of seconds desired, as well as
power down with a delay in the number of seconds desired.

4. REBOOT: As the front-panel power button is powered down, any zone set to REBOOT
will power down accordingly, and will after a three-second delay power back on. This mode is
independent of the front power button.

4865 Sterling Drive Boulder, CO 80301 Operation Guide

PH: 1 (800) PSAUDIO [e-mail] www.psaudio.com 15-059-11-1

©2018 PS Audio Inc. All rights reserved.

Rev A

10

®

Operation Guide

DirectStream Power Plant 12

Delay Mode
Continued

Network Screen

5. AUTO-REBOOT: If your Power Plant 12 is connected to the network, and if the network’s
router is being powered by the Power Plant 12, you may want to set that zone to AUTO-REBOOT.
At this setting, the Power Plant 12 will use the router and the network to ping the PS Audio Server,
essentially saying “hello, I’m an active network device and the router is working.” If the ping does not
reach our server after several tries, the Power Plant 12 will assume that the router has frozen up, and will
automatically reboot that zone, thereby resetting the router and restoring connectivity. One may wish
to power the network’s modem on this zone as well, for the same reason. This mode is independent of
the front power button.

6. ALWAYS ON: In this setting, the P12 will output power from this zone regardless of
whether the front-panel power button is engaged. As long as the Power Plant 12 is
plugged in and the back-panel power switch is set to on, any zone set to ALWAYS ON will
output regulated, regenerated AC power.

*Note*

Pressing the right or left arrow buttons will take you from control parameters for Zone A to the
parameters for Zone B, C, and D respectively. All Zone settings can be made with the same instructions
and suggestions as described above for Zone A.

The nal screen in this section is the Network Screen. Here you can see the P12 IP address and other
network information. Connecting your Power Plant 12 to the network is an option that provides extended
functionality benets. It is recommended that the Power Plant 12 be connected to the router via hard­wire connection. In addition, in order to make sure your Power Plant is fully compliant with international
regulations, please install the included ferrite noise suppressor onto the Ethernet cable close to the unit.

4865 Sterling Drive Boulder, CO 80301 Operation Guide

PH: 1 (800) PSAUDIO [e-mail] www.psaudio.com 15-059-11-1

©2018 PS Audio Inc. All rights reserved.

Rev A

11

®

Operation Guide

DirectStream Power Plant 12

Network Screen
Continued

Firmware Screen

If a network connection is not available for the Power Plant 12 there are no negative eects to the P12’s
performance in your system in terms of the quality of regenerated, regulated AC. Connecting your P12
to the network allows functionality benets only, not performance based benets.

The online interface is user friendly and can be accessed by registering one’s P12 at the following link:
powerplay.psaudio.com. You will nd a multitude of usability features including:

• P12 consumption records and performance tracking.

• Individualized zone control.

• System alerts and notications.

From the Main screen press the settings button in the upper right corner.

This will open the Firmware screen:

*NOTE* Your rmware screen may dier from the above image as rmware releases come out. Make
sure you visit our downloads page and make sure that your P12 rmware is up-to-date:

http://www.psaudio.com/support/downloads/

Unit ID

4865 Sterling Drive Boulder, CO 80301 Operation Guide

PH: 1 (800) PSAUDIO [e-mail] www.psaudio.com 15-059-11-1

The unit ID is the unique, numeric identier for the P12. It is the last 6 digits of the serial number and it is
used to allow our online resource PowerPlay to track and collate the P12's performance data.
For more information on this go to:

http://powerplay.psaudio.com/

©2018 PS Audio Inc. All rights reserved.

Rev A

12

®

Operation Guide

DirectStream Power Plant 12

Restore Defaults

Firmware Screen

CleanWave

The restore defaults button resets the user dened settings back to the factory settings.

The Bootloader / Firmware / Power Meter / Oscillator / Web versions are listed next. On occasion PS
Audio will release rmware updates for the P12. It is important that you keep your P12 fully up-to date.
Look for rmware releases in our Newsletter or at:

http://www.psaudio.com/support/downloads/

By selecting the icon labeled CLEAN the Power Plant 12 will activate the CleanWave function and the
display of the P12 will begin to countdown the time left as the P12 is applying the CleanWave signal.
CleanWave injects a series of higher frequencies that ride on the main sine wave to help “degauss”
connected magnetics.

To ensure that CleanWave is eective, make sure all connected equipment is on and functioning.
CleanWave can be used between CD’s, movies and vinyl. It is not recommended to activate CleanWave
while you are listening as it may not sound correct until the CleanWave cycle has nished. The option
exists for a 5 second or a 60 CleanWave cycle by touching the Add Time button.

4865 Sterling Drive Boulder, CO 80301 Operation Guide

PH: 1 (800) PSAUDIO [e-mail] www.psaudio.com 15-059-11-1

©2018 PS Audio Inc. All rights reserved.

Rev A

13

®

Environment Specification

US/JP

Europe/Asia

Location

Indoor use only

Indoor use only

Duty Cycle

Suitable for continuous operation

Suitable for continuous operation

Moisture Sensitivity

Not sealed against moisture

Not sealed against moisture

Operating Humidity

<80%rh

<80%rh

Storage Temperature

-40C to +40C

-40C to +40C

Operating Temperature

0C to 40C

0C to 40C

Electrical Supply Nominal Rating

US - 120V 15A

JP - 100V 15A

230V 10A 50 / 60Hz

Specications of the P12 per country.

US / JP / EX UK GR AU

Specications

DirectStream Power Plant 12

4865 Sterling Drive, Boulder, CO 80301 Specications

PH: 1 (800) PSAUDIO [e-mail] www.psaudio.com 15-059-11-1

Rev A©2018 PS Audio Inc. All rights reserved.

14

®

Instrument

JP/US

Europe / Asia

Unit Weight

39 lbs ( 17 kg)

39 lbs ( 17 kg)

Shipping Weight

48 lbs (22kg)

48 lbs (22kg)

Nominal Input Voltage

US - 95 – 145 VAC

200 –285 VAC

Maximum Peak Load

3600VA

3600VA

Output Distortion

<0.5%

<0.5%

Europe / Asia

17” W x 14” D x 3 ½ ” H (43cm W x
36cm D x 9 cm H)

39 lbs ( 17 kg)

24” x 21” x 10”

( 61cm x 53cm x 425 cm)

48 lbs (22kg)

200 –285 VAC

1200VA

Specification

Specications

DirectStream Power Plant 12

Unit Dimensions 17” W x 14” D x 3 ½ ” H (43cm W x

36cm D x 9 cm H)

Shipping Dimensions 24” x 21” x 10”

( 61cm x 53cm x 425 cm)

JP - 75 – 120 VAC

Maximum Continuous
Load

Voltage Regulation >1V >3V

JP/US – 1000 VA 1200VA

17” W x 14” D x 3 ½ ” H (43cm W x
36cm D x 9 cm H)

24” x 21” x 10”

( 61cm x 53cm x 425 cm)

Output Distortion
(Resistive Load)

(Reactive Load)

Output Impedance <0.005 ohm <0.005 ohm

Efficiency @1500 VA >85% >85%

<0.5% <0.5%

4865 Sterling Drive, Boulder, CO 80301 Specications

PH: 1 (800) PSAUDIO [e-mail] www.psaudio.com 15-059-11-1

Rev A©2018 PS Audio Inc. All rights reserved.

15

®

Standby power consumption

35 Watts

30 Watts

Energy Dissipation

1020J

2520J

DC Trigger Configuration

Tip Positive

Tip Positive

Specications

DirectStream Power Plant 12

Instrument Specication continued

Input Frequency 45 – 65 Hz 45 – 65 Hz

Under Voltage Limit US-90 Volts

JP-75 Volts

Over Voltage Limit US-144 Volts

JP-120 Volts

Peak Current Surge 90,000A 90,000A

Clamp Level 340V 775V

DC Trigger Voltage 5 – 15Vdc 5 – 15Vdc

174 Volts

275 Volts

4865 Sterling Drive, Boulder, CO 80301 Specications

PH: 1 (800) PSAUDIO [e-mail] www.psaudio.com 15-059-11-1

Rev A©2018 PS Audio Inc. All rights reserved.

16

®

Warranty

DirectStream Power Plant 12

Limited Three Year Warranty

Registering

Coverage

Should I Register My Product?

• Registering your product validates the warranty start date.

• If you do not register your product within 30 days of service, a copy of your purchase receipt.
from an authorized PS Audio dealer may be used as a proof of purchase to establish the
warranty start date.

• If no proof of purchase from an authorized PS Audio dealer or registration is provided, the
production date of the product will be used to determine the warranty start date.

• Registration can be completed online, by phone, by mail, or by email.

What Does this Warranty Cover?

This warranty covers defects in material and workmanship for products purchased from PS Audio or
its authorized dealers and agents.

What Will PS Audio Do to Correct the Problem?

In the event your product fails your sole remedy under this limited warranty shall be to return the
product to PS Audio or an authorized PS Audio repair center. The product will be repaired without
charge for parts or labor, replaced, or the purchase price refunded through the original point of
purchase, at the option of PS Audio.

What is the Period of Coverage?

This limited warranty is in eect for 3 years from the date the unit was rst purchased from PS Audio
or its dealers and agents.

Shipping

Who Pays for Shipping?

You are responsible to pay for the safe and proper shipment of the warrantied product to PS Audio
or its authorized repair center.

The PS Audio authorized repair center will pay the cost of returning the repaired or replacement
product to you under this warranty.

4865 Sterling Drive, Boulder, CO 80301 Warranty

PH: 1 (800) PSAUDIO [e-mail] www.psaudio.com 15-059-11-1

©2018 PS Audio Inc. All rights reserved.

Rev A

17

®

Warranty

DirectStream Power Plant 12

Not Covered

Limitations

What Does this Warranty Not Cover?

This warranty does not cover damage due to:

• Accidents, carelessness, improper transportation, misuse, neglect, or abuse.

• Failure to follow the operating instructions that are provided by PS Audio in the owner’s
manuals (available for download at psaudio.com).

• Use in any manner inconsistent with PS Audio’s operating instructions (available for download
at psaudio.com).

• Lack of routine maintenance.

• Connection to an improper voltage supply.

• Alterations or modications to the unit.

• Improper or unauthorized repair, including repairs not authorized by PS Audio or a PS Audio
authorized repair center.

• Fire, lightning, ood, “acts of God,” or other contingencies beyond the control of PS Audio.

• Products purchased through an unauthorized source (if you have questions as to whether or
not a dealer is authorized, please contact customer support at psaudio.com).

• Products with a factory-applied serial number that has in any way been altered, defaced, or
removed .

Limitations on PS Audio’s Obligations Under this Warranty

• In no event will PS Audio’s liability to you exceed the original purchase price of the unit.

• This warranty does not cover the cost of custom installation, customer instruction, setup
adjustments, or signal reception problems.

• This warranty does not cover consequential and incidental damages. Some states do
not allow the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you.

• In the event your warrantied product cannot be repaired, PS Audio will replace or refund
the unit. We reserve the right to replace any out-of-stock, discontinued, or limited edition
products with a comparable product. Discontinued products may not be available for
warranty replacement.

Warranty Transfer

How Can the Warranty be Transferred?

This warranty is for the benet of the original purchaser of the product. The warranty may be
transferred to a subsequent purchaser during the 3 year warranty period. To do this, you must

contact PS Audio directly to set up transfer of registration.

4865 Sterling Drive, Boulder, CO 80301 Warranty

PH: 1 (800) PSAUDIO [e-mail] www.psaudio.com 15-059-11-1

©2018 PS Audio Inc. All rights reserved.

Rev A

18

®

Service

DirectStream Power Plant 12

If you require
service in North
America

Obtain an RMA
number

Use original
packing

State law

How Do I Get Warranty Service?

To locate an authorized PS Audio repair center, for service assistance, or for help with the operation
of a product or just for information, please contact PS Audio customer support.

Warranty Service Within the US

• You must rst obtain a Return Merchandise Authorization Number (RMA#) to receive
warranty service and prior to returning any item. Contact PS Audio or an authorized PS
Audio repair center to receive an RMA#.

• You must put the RMA# on all returns. If it is not clearly marked, PS Audio will return the
package back to you, freight collect.

• Original packaging should be used for the safe transit of your PS Audio unit to the repair
center. If you do not have the original packing, PS Audio can sell and ship to you replacement
packaging.

• You are responsible for the cost of shipping the product to a PS Audio authorized repair
center. You should insure the product for its full retail cost in the event it gets lost or
damaged in transit. PS Audio is not responsible for damage incurred in products sent to us.

• Shipping your product in non-PS Audio packaging may void this warranty. PS Audio
reserves the right to charge you for new factory packaging to return your product after a
repair.

How State Law Applies

This warranty gives you specic legal rights, and you may also have other rights which vary from
state to state.

If you are outside

Warranty Service Outside of the US

the US

PS Audio has authorized distribution in many countries of the world. In each country, the authorized
importing distributor has accepted the responsibility for warranty of products sold by that distributor.

Warranty service should be obtained where the product was purchased.

4865 Sterling Drive, Boulder, CO 80301 Service

PH: 1 (800) PSAUDIO [e-mail] www.psaudio.com 15-059-11-1

©2018 PS Audio Inc. All rights reserved.

Rev A

19

®

Service

DirectStream Power Plant 12

Changes to Our Products

PS Audio reserves the right to modify the design of any product without obligation to purchasers
of previously manufactured products and to change the prices or specications of any products

without notice or obligation to any person.

Your Serial
Number

Your Purchase
Information

Date of Purchase

4865 Sterling Drive, Boulder, CO 80301 Service

PH: 1 (800) PSAUDIO [e-mail] www.psaudio.com 15-059-11-1

©2018 PS Audio Inc. All rights reserved.

Rev A

20

®

Notes

DirectStream Power Plant 12

4865 Sterling Drive, Boulder, CO 80301 Notes

PH: 1 (800) PSAUDIO [e-mail] www.psaudio.com 15-059-11-1

©2018 PS Audio Inc. All rights reserved.

15-059-01-2

Rev A

21

®

Notes

DirectStream Power Plant 12

4865 Sterling Drive, Boulder, CO 80301 Notes

PH: 1 (800) PSAUDIO [e-mail] www.psaudio.com 15-059-11-1

©2018 PS Audio Inc. All rights reserved.

15-059-01-2

Rev A

22