For use with Zello and other push-to-talk apps
PRYMEBLU BTH-SPM100-ZD
Wireless Bluetooth Speaker Microphone
on Android smart phones.
PTT Button
This button is used to activate the
push-to-talk feature of the Zello app.
It can also be used to answer or hang
PRYME® and PRYMEBLU® are trademarks owned by PRYME Radio Products,
Brea CA. All other product or service names are the property of their respective owners.
Model No.: BTH-SPM100-ZD
Made in Taiwan
up incoming telephone calls.
© 2014 PRYME Radio Products, Brea CA. All Rights Reserved
Controls and Connection
Front Firing Speaker
Received calls are heard over this speaker.
The volume level is controlled using the
volume controls on the phone.
Microphone:
This microphone picks up
the user’s voice audio
Clothing Clip
The alligator-type clip secures
the speaker ,icrophone
to the user’s clothing during use.
The clip can be rotated to allow the
microphone to be better positioned.
TOLL FREE: 800.666.2654
911 Mariner St., Brea, CA 92821
PH: 714.257.0300 FAX: 714.257.0600
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment o
and on, the user is encouraged to try to correct the interference by one of the following
measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit dierent from that to which the
receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. To maintain compliance with FCC RF exposure compliance
requirements, please avoid direct contact to the transmitting antenna during
transmitting.
RF Exposure Warning!
This device contains transmitters and receivers which emit Radio Frequency (RF)
energy. The device is designed to comply with the limits for exposure to RF energy set
by the Federal Communications Commission (FCC) of the United States, Industry
Canada (IC) of Canada, and the regulating entities of other countries.
If you are still concerned about exposure to RF energy,
you can further limit your exposure by limiting the
amount of time you use the equipment or by placing
more distance between your body and the device,
since exposure level drops o dramatically
with distance.
The BTH-SPM100-ZD speaker microphone has an internal Lithium Ion rechargeable battery pack which
must be charged prior to operation, and must be recharged regularly. A fully charged battery will
provide approximately 5 hours (or more) of continuous operation before needing to be recharged.
However, operating time can vary depending on usage and the condition of the battery pack.
Recharge the battery regularly.
Earphone / Charge Jack
WWW.PRYME.COM
This jack is used to connect the
supplied charge cable to the
speaker microphone. It can also
be used to connect a wired listen-only
earphone for enhanced privacy.
1.0Z September 2014
Multifunction Button
Holding down this button for one second
will turn the speaker microphone on and o.
This button can also be used to place the speaker
microphone into pairing mode so that it can be
connected wirelessly to a cellular phone
2
Pairing with a SmartphoneCharging the Speaker Microphone
Status LED
The LED ashes messages that
let the user know the current
status of the speaker microphone.
To charge the speaker microphone
1. Ensure the device is turned o using the multifunction button.
2. Plug the charge cable into any powered USB outlet, such as the included AC wall charger, and then
into the charge jack on the bottom of the speaker microphone. You will need to remove the protective
rubber cover that is inserted into the charge jack. (To prevent dust and moisture from damaging your
speaker microphone, always ensure this cover is in place when you are not charging.)
3. Once the charging process has begun, the LED indicator on the bottom of the speaker microphone
will show a constant red light.
4. Typical charge time is approximately three hours. Actual charge time will vary depending on several
factors including the battery’s charge state, condition, and age.
5. Disconnect the charger from the adapter when charging is completed.
Charging Cautions:
- Do not use a wall charger or charge cable that appears to be damaged. (Example: frayed wires,
melted plastic, etc.) Contact PRYME to get a new manufacturer-approved replacement charger.
- Do not tamper with or modify the speaker microphone or charger.
- Always turn the speaker microphone o when charging.
3 4
The BTH-SPM100-ZD speaker microphone is designed to work with smartphones running the Android
operating system. Prior to normal operation, the phone and speaker microphone must be paired together
using the following process:
1. Activate the pairing mode on the speaker microphone by holding down the multifunction button until
the status LED ashes BLUE-RED-BLUE-RED continuously in sequence.
2. On your phone, go to Settings > Bluetooth. Move the Bluetooth slider to turn the phone's Bluetooth
radio on.
3. Select “Search for Devices” from the phone’s Bluetooth menu. The phone will scan for nearby Bluetooth
devices and a list showing the names of nearby Bluetooth devices will be shown on the screen.
4. Choose “BTH-SPM100-ZD” from the list.
5. Keep the phone and speaker mic near each other and wait a few seconds. The devices will pair to each other.
Reconnecting a Previously Paired Speaker Microphone and Phone
Once the speaker microphone and phone have been successfully paired together, both devices will
remember that connection. They will reestablish their link whenever the speaker microphone and phone
are both powered on and in within range of each other, as long as the Bluetooth radio is enabled in the
phone. Re-establishing this connection can take 10-60 seconds.
In the event that the phone and speaker microphone do not automatically reestablish their link, simply
press the multifunction button on the BTH-SPM100-ZD to restore the connection.
Setting Up the Zello App
EH-1289SC
Plasc D-Ring
15” Coiled
3.5 mm right-angle
EH-1289XC
Plasc D-Ring
25” Coiled
3.5 mm right-angle
EH-1389SC
Acousc Tube
15” Coiled
3.5 mm right-angle
Using the Speaker Microphone with Zello
To get the Zello app on your phone and set it up to work with the BTH-SPM100-ZD speaker
microphone, do the following:
1. Install Zello from your Zello@Work network, or download the app from the Google Play store.
2. Make sure that your phone's Bluetooth radio is enabled, and that the speaker microphone is
powered on and that the microphone and phone are connected to each other.
3. Open Zello and go to Menu > Options > Under the Hood.
4. Under "Bluetooth PTT Control," choose "PTT-Z100". You should see a popup indicating the device
control has been activated. If you don't see it, you may need to power cycle the headset and repeat
this step.
5. Open the Talk screen in Zello (the screen with a big round button). In the bottom-left corner of
the screen, tap-hold and slide to the Bluetooth icon to activate the speaker microphone in Zello.
Once setup, you will be able to use the speaker microphone with the Zello app, even if Zello is
running the background.
-To activate Zello’s push-to-talk feature, press and hold the PTT button on the speaker microphone.
-When Zello is transmitting a call, audio will be picked up by the BTH-SPM100-ZD’s built-in
microphone.
-Incoming calls received by Zello will be heard over the BTH-SPM100-ZD’s built-in speaker or
through the optional earphone if you are using one.
Making and Receiving Phone Calls
You can also use the speaker microphone to make and receive phone calls.
-You can initiate a phone call by using the Phone Dialer app in the phone.
-Phone audio will be routed to the BTH-SPM100-ZD’s built-in microphone and speaker (or earphone,
if you are using one).
-To answer an incoming call, press the PTT button on the speaker microphone.
-While on a call, you can press the PTT button on the speaker microphone to hang up the phone
and end the call.
STATUS LED MESSAGES
The meanings of the various status LED messages shown by the speaker microphone are
shown on the following table:
LED INDICATION
Constant Red (while plugged into charger)
Constant Red and Blue (while plugged into charger)
Flashes red-blue-red-blue repeatedly
Two blue ashes every two seconds
One blue ash every two seconds
Constant red with one blue ash every two seconds
No indication
MEANING
Charge mode
Charging is nished
Pairing mode
Speaker microphone is powered on but not paired
Speaker Microphone is powered and paired
PTT is pressed
Speaker microphone is powered o
65
OPTIONAL EAPRHONES
Although the BTH-SPM100-ZD has a built-in speaker for listening to received calls,
some users may prefer to use a listen only earphone for enhanced privacy.
The accessory jack on the speaker microphone will accept any mono
earphone with a 3.5 mm audio plug.
When an earphone is used, the
front-ring speaker is disabled.
PRYME EH-1389SC model shown.
Earphone sold separately.
PRYME makes a variety of listen-only earphones in
dierent styles that will work with the BTH-SPM100.
Model Earphone Style Cable Length/Type Connector
EH-389SC Rubber Ear Hook 15” Coiled 3.5 mm right-angle
EH-389XC Rubber Ear Hook 25” Coiled 3.5 mm right-angle
EH-1389X Acousc Tube 30” Straight 3.5 mm right-angle
EH-1399X Acousc Tube 30” Straight 3.5 mm straight
SPECIFICATIONS
Bluetooth Version:
Speaker Output:
Maximum Audio Level:
Receiver Sensitivity:
Power Class:
Range:
Display:
Bluetooth Prole:
Operating Voltage:
Battery Capacity:
Operating Time (Standby)
Operating Time (Typical)
Operating Time (Continuous Talk)
Push-to-Talk Function:
Operating Temperature:
Weight:
v2.1+EDR
1 watt
126 dB
-82 dBm (typ.)
Bluetooth class 2
10 meters
Blue and Red
HFP,HSP,SPP Prole
5 VDC
240 mAH
> 50 hours
> 11 hours
> 5 hours
Built-in
-70°F to +120°F (approx.)
60 grams (approx.)
7
SUPPORT AND WARRANTY
PRYME Radio Products warrants this product against defects in materials or workmanship for a
period of one year from the date of retail purchase. PRYME will repair or replace a defective unit,
at our option, without charge for parts or labor. The limited warranty is extended only to the
original purchaser and is valid only to consumers in the United States and Canada. It does not
cover damage or failure caused by or attributable to Acts of God, abuse, misuse, improper or
abnormal usage, faulty installation, improper maintenance, lightning, or other incidences of
excessive voltage, or any tampering or repairs by other than a PRYME authorized repair facility. It
does not cover replacement of consumable parts, transportation costs, or damage in transit.
Repair or replacement under the terms of this warranty does not extend the terms of this
warranty. This warranty can only be modied by an ocer of PRYME Radio Products, and then
only in writing. Should this product prove defective in workmanship or material, the consumer’s
sole remedies shall be such repair or replacement as provided by the terms of this warranty.
Under no circumstances shall PRYME Radio Products be liable for any loss or damage, direct,
consequential, or incidental, arising out of the use of or inability to use this product. Some states
do not allow limitations on how long an implied warranty lasts or the exclusions or limitations of
incidental or consequential damages, so the above limitations or exclusions may not apply to
you. This warranty gives you specic legal rights. You may also have other rights, which may vary,
from state to state.
For support or warranty service on your PRYME product, contact us at 1-800-666-2654 or visit us
on the web at www.PRYME.com.
COPYRIGHT AND TRADEMARK INFO
© 2014 PRYME Radio Products, Brea CA. All rights reserved.
PRYME® and PRYMEBLU® are trademarks owned by PRYME Radio Products, Brea CA.
Android is a trademark of Google Inc.
All other product or service names are the property of their respective owners.
DISCLAIMER: The Bluetooth wireless link used by PRYMEBLU products is an open
standard, unsecured technology. As such, it is not recommended for rst-responder or
other mission critical users.
8
Loading...