PRS Studio RS-4003, RS-4004, RS-4002, RS-4083, RS-4082 Assembly Instructions Manual

1 Year Limited Warranty.

Dot Line Corp. warrants that if the accompanying product proves to be
defective to the original purchaser in material or workmanship within 1
year from the original retail purchase, Dot Line Corp. will, at its option,
either repair or replace same without charge (but no cash refund will be
made).
What you must do to enforce the warranty: You must deliver, mail or
ship the product together with the original bill of sale, to:

Dot Line Corp. 9420 Eton Ave., Chatsworth, CA 91311

Phone [phone] Fax [phone].

Limitation of Liability and Remedies: This warranty is void if any

defects are caused by abuse, misuse, negligence or unauthorized
repairs. All liability for incidental or consequential damages is specifically
excluded. The company shall have no liability for any damages due to
lost profits, loss of use or anticipated benefits, or other incidental,
consequential, special or punitive damages arising from the use of, or
inability to use, this product, whether arising out of contract, negligence,
tort, or under any warranty, even if the company has been advised of the
possibility of such damages. The Company’s liability for damages in no
event shall exceed the amount paid for the product. The Company
neither assumes nor authorizes anyone to assume for it any other
liabilities.
Some states do not allow for the exclusion of incidental or consequential
damages, so the above exclusion may not apply to you. This warranty
gives you specific legal rights and you may have other rights which vary
from state to state.

RPS Studio Products are Marketed exclusively by:

Dot Line Corp. 9420 Eton Ave.

Chatsworth, CA 91311

818-700-9997 • Fax [phone]

www.dotlinecorp.com

Product Made in China © Dot Line Corp. 2008

These Instructions are for RS-4000 Series Light Kits. Pictures may vary.
Specifications are subject to change. Printed August 2008.

Light Kit

Assembly Instructions

These instructions are for the items listed below:
RS-4002: Includes 2 10" Reflectors, 2 Socket Sets, 2 Light

Stands, Carrying Box

RS-4003 Includes 3 10" Reflectors, 3 Socket Sets, 3 Light

Stands, Carrying Box

RS-4004 Includes 2 10" Reflectors, 1 8" Reflector, 1 Barn Door Set,

3

Socket Sets, 3 Light Stands, Carrying Box

RS-4082 Includes 2 8" Reflectors, 2 Socket Sets, 2 Light

Stands, 2 Umbrellas, 2 Bulbs, Carrying Box

RS-4083 Includes 3 8" Reflectors, 3 Socket Sets, 3 Light

Stands, 3 Umbrellas, 3 Bulbs, Carrying Box

ASSEMBLY INSTRUCTIONS

1. Remove all of the boxes from the
carry/storage box.

2. Under them you will find a tray that
holds the light stands. Lift out the tray and
remove the light stands. Set up the light
stands by opening the legs fully. Lock the
legs in place with the Locking Screw at
the leg junction. (You may need to loosen
the locking screw at the leg junction to
open the legs.) The height of the light
stand is adjustable by unlocking the
section(s) at each junction, setting the
desired height and re-locking the section
(s) with the flip-lock levers.

3. Remove the Ceramic Light Sockets
from their box and loosen the
Angle Lock for the socket.
Adjust the socket so that the
ceramic socket is 90° to the
stand mount. Re-lock the angle
lock. If the end of the lock
handle is facing in the direction
of the socket, it will be
necessary to pull out the handle
and rotate it so the handle is
facing as in the picture.
Releasing the handle will
automatically allow it to seat.
Next, back out the stand locking
screw enough to allow the
socket to be mounted on the
stand. Secure the socket to the
stand and re-secure the screw
to hold the socket onto the
stand.

4. At this point, the ceramic
socket should be 90° to the light
stand. The socket is mounted to
a metal round plate with holes
and it has a knurled screw that
goes through the plate. Back out
the screw so that the end is
flush with the plate. This will
allow you to bayonet the
reflector onto the metal backing
plate.

5. Remove the reflector from the box and
line up the studs at the rear of the reflector
with the holes in the mounting
plate. Be sure the oblong hole in
the side of the reflector near the
cone is on the bottom. (This
allows you to mount the
umbrellas, if used, properly).
Insert the studs into the holes of
the socket plate and turn the
reflector so that the studs rotate
to the small part of the holes in
the mounting plate. Secure the reflector with
the knurled screw.

6. Insert a photoflood bulb into the socket.
Any of the following E-27 base bulbs may
be used: BBA, BCA, EBV, EBW, ECA, or
ECT.
Be sure to allow the unit to cool before
disassembly. The bulbs get very hot in use.

7. To adjust the focusing of the lamp,
loosen the Shaft Securing Knob and
push/pull the socket set back and forth until
the desired angle of light is achieved.

8. If your kit was supplied with umbrellas,
they mount by inserting the shaft through
the hole of the reflector into the umbrella
mounting hole on the Ceramic Socket Set
stand clamp.

Leg Junction

Locking Screw

Metal Plate

Angle Lock

Umbrella Hole

Flip-Locks

Cermaic Socket Set

with Stand Mount

Light Stand

Back out this screw to bayonet the
reflector onto the metal backing plate

Shaft Securing Knob

Push/Pull to Focus