Proware Technologies Co MN527V1 Users Manual

PW-MN527

300Mbps Wireless N USB Module

User Guide

Version 1.0

July 31, 2012

PROWARE TECHNOLOGIES CO., Ltd.

Copyright Notice:

Copyright © 2012, PROWARE Technologies CO,. Ltd . All Rights Reserved.

No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system,
or translated into any language, in any form or by any means, electronic, mechanical, magnetic,
optical, chemical, manual or otherwise without the prior written permission of PROWARE
Technologies CO,. Ltd

is a registered trademark of PROWARE Technologies CO,. Ltd.

All trademarks are the properties of their respective owners.

Important:

This product is only for Consumer Electronics device factory’s using. Terminal
customers will not have direct access to buy and use this product.

Revision History

Release

Date

Revision

Initials

1.0

2012-7-31

First release.

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:

 Reorient or relocate the receiving antenna.
 Increase the separation between the equipment and receiver.
 Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

 Consult the dealer or an experienced radio/ TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.

This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.

FCC RF Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body.

This device is intended only for OEM integrators under the following conditions:

 The antenna must be installed such that 20 cm is maintained between the antenna

and users, and

 The transmitter module may not be co-located with any other transmitter or antenna.

As long as 2 conditions above are met, further transmitter test will not be required. However, the
OEM integrator is still responsible for testing their end-product for any additional compliance
requirements required with this module installed

IMPORTANT NOTE: In the event that these conditions can not be met (for example certain
laptop configurations or co-location with another transmitter), then the FCC authorization is no
longer considered valid and the FCC ID can not be used on the final product. In these
circumstances, the OEM integrator will be responsible for re-evaluating the end product
(including the transmitter) and obtaining a separate FCC authorization.

End Product Labeling

This transmitter module is authorized only for use in device where the antenna may be installed
such that 20 cm may be maintained between the antenna and users. The final end product
must be labeled in a visible area with the following: “Contains FCC ID: WWMMN527V1 . The
grantee's FCC ID can be used only when all FCC compliance requirements are met.

Manual Information To the End User

The OEM integrator has to be aware not to provide information to the end user regarding how to

install or remove this RF module in the user’s manual of the end product which integrates this

module.

CE Mark Warning

This is a class B product. In a domestic environment, this product may cause radio interference,
in which case the user may be required to take adequate measures.

CONTENTS

Package Contents .................................................................................................... 7

Chapter 1 Introduction ........................................................................................... 8

1.1 Overview of the Product ............................................................................................ 8

1.2 Features ..................................................................................................................... 8

Chapter 2 Installation Guide .................................................................................. 9

2.1 Hardware Installation ................................................................................................. 9

2.2 Software Installation .................................................................................................. 9

Chapter 3 Linux Installation Guide (For Consumer Electronics) ..................... 14

3.1 Hardware Installation ............................................................................................... 14

3.2 Software Installation ................................................................................................ 14

Appendix A: Specifications ................................................................................... 15

Appendix B: Glossary ............................................................................................ 16