Indoor Mini High Speed PTZ Dome Camera
PTZ-9610-A
User Manual
2
Contents
Features ................................................................................................................... 3
1.1 Features ..................................................................................................... 3
1.2 Specifications ........................................................................................... 5
Installation .............................................................................................................. 6
2.1 Installation and Connection ...................................................................... 6
2.1.2. Ceiling Mount ....................................................................................... 6
2.1.3 Cabling................................................................................................... 6
2.2.1 Camera ID Setup ................................................................................... 6
2.2.2 Communication Protocol and Baud rate Setup ..................................... 7
Operation ................................................................................................................ 8
3.1 Check points before operation.................................................................. 8
3.2 Operation .................................................................................................. 8
3.2.1 Preset function pre-check ...................................................................... 8
3.2.2 Reserved Preset ..................................................................................... 9
3.3 Camera Lens control. ............................................................................... 9
3.3.1 Zoom ...................................................................................................... 9
3.3.2 Focus ...................................................................................................... 9
3.3.3 Iris ........................................................................................................ 10
How to Use OSD Menu ........................................................................................ 10
4.1 Basic operation of Main menu ............................................................... 10
4.2 Main menu .............................................................................................. 10
4.2.1 System Information ............................................................................. 11
4.2.2 Address Setting .................................................................................... 12
4.2.3 Motion ................................................................................................. 12
4.2.4 Patterns ................................................................................................ 14
4.2.5 Camera setup ....................................................................................... 15
4.2.6 Cruise Setting ...................................................................................... 23
4.2.7 Display Setup....................................................................................... 23
4.2.8 Restore Factory Default ...................................................................... 23
4.2.9 Reboot System ..................................................................................... 23
Trouble Shooting .................................................................................................. 24
Safety Information ................................................................................................ 25
3
Features
1.1 Features
Camera Specifications:
CCD Sensor: 1/3” Sony Effio CCD Color 960H.
Zoom Magnification: 10X Optical zoom.
Day & Night function: The camera is configured to switch to the black and white mode
automatically under low light conditions and at night for clear images.
Various focus mode: Auto Focus / Manual Focus / Semi-Auto Focus.
Powerful Pan / Tilt Functions:
● Max 360°/sec high speed Pan / Tilt motion.
● Automatic flip.
● Support direction indication.
● Programmable cruise and presets.
● Soft address enables to set up the address and number of the camera.
● Adopt Vector Drive Technology, Pan / Tilt motions are accomplished in a shortest path.
As a result, time to target view is reduced seriously and the video on the monitor is very
nature to watch.
● For jog operation using a controller, since ultra slow speed 0.05°/sec can be reached. It is
very easy to locate camera to desired target view.
● Support zoom proportional Pan / Tilt speed. Camera can be moved to a desired position
in accurate manner even through high zoom ratio.
Preset, Linear, Preset position cruise, Pattern, Auto Scan.
● Max. 256 presets are assignable and characteristics of each preset can be set up
independently.
● Linear scan enables to move camera repetitive between two preset positions with
assigned speed.
● Preset position cruise: the group can have max 30 entities of preset. This enables for
camera to move a combinations of this functions repetitively.
● 4 Patterns with 100 commands can be recorded and executed. This enables the camera to
track a surveillance trajectory as closely as possible.
● 360° continuous scan.
● 360° intermittent scan. The camera will have seconds stop during each 90° turning.
● Auto scan: this enables to move the camera to execute the certain scan when no-operation
4
for a long time.
● Reserved Presets for special purpose: besides regular 256 presets, direct calling of
reserved presets enable to set up many of camera functions with / without using OSD
menu.
PTZ (Pan /Tilt /Zoom) Control:
● RS485 Communication.
● Pelco D / Pelco P, special protocols available.
OSD (On screen Display) Menu:
● OSD menu is provided to display the status of camera and to configure the functions
interactively.
● English menu.
● Each display item can be turned ON or OFF independently.
5
1.2 Specifications
Video Signal System
NTSC
Camera
CCD
1/3” Sony Effio CCD Color 960H
Max. Pixels
976 (H) X 494 (V)
Horizontal Res
700TV Lines
S/N Ratio
50dB (AGC off)
Zoom
X10 Optical Zoom
Focal Length
F1.8, f=3.8~38mm
Min. illumination
0.7Lux (Color),0.02Lux (B/W), F1.8, 50 IRE
Day & Night
Auto / Day/ Night
Focus
Auto / Manual/ Semi Auto
Shutter Speed
X128~X2, 1/50~1/120000 sec
White Balance
Auto / Manual (Red, Blue gain adjustable)
BLC
Low / Middle / High / Off
DNR
Low / Middle / High / Off
Pan / Tilt
Range
Pan :0~360°(Endless)
Tilt: 0~180°
Pan/Tilt Speed
Preset : 360°/sec
Manual:0.05~360°/sec (proportional to zoom)
Auto Pan : 1~180°/sec
Preset
256 Preset (Label, Camera Image Setting)
Pattern
4 Pattern, 100 commands
Scan
30 action entities per scan
Other Functions
Auto Flip, Auto Parking, Power up Action etc.
General
Communication
RS-485
Protocol
Pelco-D, Pelco-P
Baud rate
2400, 4800, 9600
6
Installation
2.1 Installation and Connection
(1) Connect Camera
Plug the terminals into the bottom of the main unit, then, fix the main unit with screws
supplied.
2.1.2. Ceiling Mount
（1）Fix the main unit to the ceiling using screws provided.
After wiring cables to terminals, plug the terminals into the bottom of main unit. Then, fix the
main unit with screws provided.
2.1.3 Cabling
Connector Interface
2.2 DIP Switch Setup
Before you install the camera, you should set the DIP switches to configure the camera ID,
Baud rate, and communication protocol.
Default ID: 1
Baud rate: 2400
Protocol: Pelco-D.
2.2.1 Camera ID Setup
The range of ID is 0~255. Factory default of Camera ID is 1.
ID number of camera is set using binary number. The number from 1~8 present 1, 2, 4, 8,
7
16, 32, 64 and 128. For example, switch 1, 3, 5, 7 to “ON” position, the corresponding
ID should be 1+4+16+64=85.
The example is shown bellow.
ID No
Code Switch
ID No
Code Switch
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
0
0 0 0 0 0 0 0 0
10
0 1 0 1 0 0 0 0
1
1 0 0 0 0 0 0 0
20
0 0 1 0 1 0 0 0
2
0 1 0 0 0 0 0 0
30
0 1 1 1 1 0 0 0
3
1 1 0 0 0 0 0 0
50
0 1 0 0 1 1 0 0
4
0 0 1 0 0 0 0 0
100
0 0 1 0 0 1 1 0
5
1 0 1 0 0 0 0 0
101
1 0 1 0 0 1 1 0
6
0 1 1 0 0 0 0 0
150
0 1 1 0 1 0 0 1
7
1 1 1 0 0 0 0 0
200
0 0 0 1 0 0 1 1
8
0 0 0 1 0 0 0 0
255
1 1 1 1 1 1 1 1
2.2.2 Communication Protocol and Baud rate Setup
8
Select the appropriate protocol with DIP switch combination.
Switch State
Protocol
Pin No
Pin 1
Pin 2
Pin 3
Pin 4
Protocol
OFF
OFF
PELCO-P
ON
OFF
PELCO-D
OFF
ON
Auto
ON
ON
Reserved
Baud rate
OFF
OFF
9600
ON
OFF
2400
OFF
ON
4800
ON
ON
9600
Operation
3.1 Check points before operation
Before power is connected, please check the cables carefully.
The camera ID of the controller must be identical to that of the camera to be controlled.
The camera ID can be checked in the System Information of OSD Menu.
If you controller supports multi-protocols, the protocol must be changed to match to that
of the camera.
If you change camera protocol by changing DIP switch, the change will be effective
after you reboot the camera.
Since the operation method can be different for each controller available, refer to the
manual for your controller if camera can not be controller properly.
3.2 Operation
Note: The manual will refer to our CCTV tester to explain how to operate and control the
camera.
3.2.1 Preset function pre-check
● Check how to operate preset, Scan, Auto Pan and Pattern function with controller or DVR
9
in advance to operate camera function using them.(Refer to your System keyboard Manual)
● If controller or DVR has no pattern button or function, use shortcut keys with preset
numbers. For more information, refer to “Reserved Preset” in this manual.
● Use “UP, DOWN, LEFT, RIGHT” direction key to move to a desired position,，then,
press ”Zoom, Lens, Iris” to adjust the pictures.
● Press “preset setup” to input number, then confirm by a press on setup key.
Call Preset
● Press “Call Preset” key and input No of preset, the confirm by a press on “Setup” key, the
camera will move to the desired preset, meanwhile, the zoom, lens and iris will automatically
change to preset states
3.2.2 Reserved Preset
Some Preset numbers are reserved for direct access to specific functions in OSD menu. These
direct commands via preset provide quick execution of various functions using keyboard
controller as well as simplify the interface with DVR.
Reserved Preset
Function
Go/Set Preset <95>
Enters into OSD menu
Go Preset <80>
Reserved.
Go Preset <82>
Runs cruise function
Go Preset <83>
Clean all presets
Go Preset <84 ~ 87>
Runs Pattern 1 ~ 4
Go Preset <88>
Reserved ( Runs wide dynamic function)
Go Preset <89>
Reserved (Stop wide dynamic function)
Go Preset<96>
Runs 360° scan(pause 3 seconds per 90°)
Go Preset <97>
Runs linear scan
Go Preset <98>
Runs cruise function
Go Preset <99>
Runs Auto pan function
3.3 Camera Lens control.
3.3.1 Zoom
Adjust the lens distance to enlarge or downsize the image for best effect or wide-angle effect.
Using “ZOOM IN / TELE” key to enlarge the images.
Using “ZOOM OUT/ WIDE” key to downsize the images.
3.3.2 Focus
Adjust definition of the object of scene
Press “Focus Far” key to shorten the distance of far scene.
10
Press “Focus Near” key to shorten the distance of near scene.
3.3.3 Iris
Press “Iris Open” key to adjust the brightness.
How to Use OSD Menu
After power up or restart, the present Protocol, Baud rate and Address will be displayed on
the screen as below:
4.1 Basic operation of Main menu
Go <Preset 95> to enter into main menu.
Using “Iris open” and “Iris close” to confirm or exit main menu.
Using “UP/DOWN” keys or joystick to move cursor to sub-menu, press “Iris open” to
enter into menu.
Using “UP/DOWN” keys or joystick to move cursor to the function and press“Iris open”
to choose the function.
Using “UP/DOWN” keys or joystick to set up and press “Iris open” to save.
Move the cursor to “BACK” and press “Iris open” to back to main menu.
Note: There might display different information due to different camera.
4.2 Main menu
MAIN MENU
SYSTEM INFORMATION
ADDR SETTING
MOTION
PATTERNS
CAMERA
CRUISE SETTING
DISPLAY SETUP ON
RESTORE FACTORY DEFAULT
REBOOT SYSTEM
EXIT
PTOL： PELCO-P
COMM：2400，N，8，1
ADDR： 1
11
<SYSTEM INFORMATION>：Shows system information.
<ADDR SETTING>：Select and setup Soft/Hard address.
<MOTION>：Setup for motion related settings.
<PATTERNS>：Setup for Patterns.
<CAMERA>：Configure Camera related functions and data.
<CRUISE SETTING>：Setup presets scan.
<DISPLAY SETUP>：Enable / Disable of OSD display on main screen.
<RESTORE FACTORY DEFAULT>：Restore factory settings.
<REBOOT SYSTEM>：Reboot the system.
4.2.1 System Information
<COM>：Shows current Baud rate.
<ADDRESS>：Shows current Camera ID for PTZ control, 0~255. <PROTOCOL>：Shows
current protocol for PTZ control.
<PRESETS>：Shows the preset numbers.
<SOFTWARE VERSION>：Shows current software version of camera.
Notice: the system information can not be changed.
SYSTEM INFORMATION
COM 2400,N,8,1
ADDRESS 1
PROTOCOL PELCO-P
PRESETS 256
SOFTWARE VERSION V5.2
BACK
EXIT
12
4.2.2 Address Setting
ADDR TYPE：Choose the address type (Hard/Soft Add), when you choose soft type, the user
can setup the address by remote access.
ADDR SOFT：Setup soft address. Press UP/DOWN” keys of your controller and setup the
camera ID from 0~254.
ADDR HARD: Setup hard address. Only can be changed by DIP Switch.
Notice: Please reboot the dome camera after reset the camera ID.
4.2.3 Motion
Motion setup is to setup preset and packing action function.
SET FRAME SCAN：setup the LEFT/RIGHT extreme position between two presets.
POWER UP：This function enables to resume the last action executed before power down.
NONE: No action.
CRUISE: Cruise action between presets position.
AUTO SCAN: 360°continious scan.
RANDOM SCAN: 360°intermittemt scan action.
PARK TIME: Parking action during idle time.
TIME Setting: 15-60 (Seconds), 2…60M（Minutes）, 2…12H（Hours）.
PARK ACTION：This function enables to locate the camera to specific position automatically
if operator doesn’t operate the controller for a while. Park time can be defined as an interval.
ADDR SETTING
ADDR TYPE HARD
ADDR SOFT 3
ADDR HARD 1
BACK
EXIT
MOTION
SET FRAME SCAN
POWER UP PATTERN 4
PARK TIME 15S
PARK ACTION PATTERN 4
FRAME SCAN SPEED 16
RANDOM SCAN SPEED 16
BACK
EXIT
13
FRAME SCAN SPEED: Set the speed between two presets from1~32.
RANDOM SCAN SPEED: Set the speed of 360° continuous and intermittent scan.
Set Frame Scan
SET SCAN POSITION：Set up scan range between two positions (Left/Right extreme
position).
CLEAR FRAME SCAN：Deletes frame scan.
1. Set Scan Position
（1）Move the cursor to <Set Scan Position> and enter below interface.
（2）Move the cursor to choose the extreme position of preset by using “Left/Right” keys or
joystick of your controller, then press “Iris Open” to enter below interface:
2. Clear Frame Scan
Move the cursor to “Clear Frame Scan” to enter, the press “Iris Open” to delete the
extreme positions.
FRAME SCAN
SET SCAN POSITION
CLEAR FRAME SCAN
BACK
SET FRAME SCAN
LEFT LIMIT POSITION
IRIS OPEN TO CONTINUE
SET FRAME SCAN
RIGHT LIMIT POSITION
IRIS OPEN TO CONTINUE
CLEAR FRAME SCAN
IRIS OPEN TO CONTINUE
14
4.2.4 Patterns
4 Patterns are supported, please refer to below details:
<PATTERN NUMBER> Set Pattern number (1~4).
<PROGRAM PATTERN>: Pattern scan program.
<CLEAR CURRENT PATTERN> Deletes data in current pattern.
1．Pattern Number
（1）Move the cursor to “PATTERN NUMBER” by using direction keys and select pattern
number, then press “Iris OPEN” to confirm.
2. Program Pattern
（1）Move the cursor to “Program Pattern” by using direction keys or joystick of your
controller and press “IRIS OPEN” to enter below interface.
（2）Using keyboard or joystick of your controller to locate the start position, then press “Iris
Open” to enter.
（3）Using keyboard or joystick of controller to edit pattern route and action, Max 100 actions,
then press “Iris Open” to save.
PROGRAM PATTERN
USE THE JOYSTICK OR
KEYBOARD TO MOVE THE
CAMERA TO START POSITION
IRIS OPEN TO CONTINUE
PATTERNS
STORAGE USED 1
PATTERNS
PATTERN NUMBER 4
PROGRAM PATTERN
CLEAR CURRENT PATTERN
CLEAR ALL PATTERN
BACK
EXIT
15
4.2.5 Camera setup
We are using Samsung SDM-100P camera to explain below operation.
Notice：“Up/Down” keys for option, “Left/Right” keys for details, “Iris Open” for sub-menu.
1. Camera Label setup：press “Iris Open” to enter sub-menu and edit camera label.
Using cursor to select the letter, then press “Iris Open” key to save the setup.
2. White Balance setup
WB Mode: Auto Trace / Manual / Auto
2.1 Auto Trace: Indoor/Outdoor, The camera can automatically adjust ambient light
from1800K~10500K（Indoor：3000～10,500K; Outdoor：1,800～10,500K，）to ensure the
most nature image effect.
Auto Trace WB
Auto Trace WB mode Outdoor
Exit
Main Menu
Camera label Off
White Balance Auto
BLC Off
Auto Detection Off
Focus
Exposure
Additional Menu
Back
Exit
Camera Label
ABCDEFGHIJKLMNO
PQRSTUVWXYZabcd
e f g h I j k l m nopqrs
t u v w x y z01234567
89 ( ) < > - / # * ! ? , .
Clean Position Exit
16
2.2 Manual: Close auto WB, adjust Red and Blue level manually.
Red adjust range: 0~100 Blue adjust range: 0~100
2.3 Auto BW: This mode is the most accurate and reliable for most places.
3. Backlight Compensation setup
Backlight High/Middle/Low/Off
4. Motion Detection setup：
Match the Alarm sensor input to one of preset positions. If an external sensor is activated,
camera will move to corresponding preset position when this item is predefined.
Alarm: On/Off
Region：1~4
Region Mode: On / Off
Motion Detection
Alarm On/Off
Select Region 1
Region Mode On
Top 20…|..……….
Bottom 25….…|…….
Left 20…|.……….
Right 40….……|….
Exit
Manual WB
Red 30…|...……….
Blue 41…..…|…….
Exit
17
5. Focus Setup
1 Mode：Auto, Manual, One-off Auto focus. Press “Iris Open” to enter sub-menu.
One-off auto focus: Once the image zoom changes, the camera will automatically focus and
fix the status till the image change again.
Notice: do not use Auto Focus under the below conditions.
The target is too dark (such as black clothes or curtains).
The target is very smooth( like car surface)
The brightness contrast of the target is not very clear.
Too strong high light or back light.
Too high contrast.
Some shade in front of the target.
(1)Auto mode setup:
Using the direction keys to enlarge or downsize, press “Iris/Open” key to back.
Setup Zoom
Zoom in Zoom out
Back : press “SET” key.
Focus
Mode Auto
Zoom trace mode On
Zoom trace speed Fast
Digital Zoom On
Show Zoom Off
Initial Zoom Position Off
Lens Initialization
Exit
18
(2) One-off Auto focus and Manual focus Adjustment:
2. Zoom trace mode:
Manual Focus: Off. Auto and One-off Auto Focus: On / Off.
3. Zoom trace speed: Fast/Slow.
4. Digital zoom: On / Off, range: X2~X10.
5. Show zoom: On / Off.
6. Initial zoom position：Using direction keys to move the cursor to “On”, then press “Iris
Open” to set up.
Zoom range: X1~X10
7 Lens Initialization: press”Iris open/Set” key to initialize the lens.
8 Exposure setup:
Digital Zoom
Digital Zoom X2
Exit
Initial Zoom Position
Initial Zoom Position X1
Exit
Setup Zoom
Zoom In Zoom Out
Near Far
Back: Press “SET” key
Exposure
Brightness 25….…|…….
Iris Auto
Shutter ——
AGC Off
SSNR Off
SENS-UP Off
Exit
19
Brightness range: 0~100.
Iris：Auto/ Manual. Press “Iris Open” to enter into manual setup
If the number of iris is set to higher, the image will be brighter.
Shutter mode: Flicker / Manual / Auto
The shutter speed of Anti-flash is 1/100（NTSC）， 1/120（PAL）
Manual mode setting (PAL）:2X、4X、6X、8X、10X、12X、14X、16X、24X、
32X、64X、128X、1/120000、1/60000、1/30000、1/10000、/1/7000、1/5000、1/2500、
1/1600、1/1000、1/700、1/500、1/250、1/100、1/50.
Notice: Auto shutter setting only for manual iris mode.
AGC: High / Middle/ Low / Off.
Enhances image brightness automatically in case that luminance level of image signal is too
low.
Range: 5-41
SSNR：High / Middle / Low / Off
Enhances images by reducing noises when gain level of images too high.
Sens-up: Manual / Off
Adjust CCD exposure time.
Auto mode setting: 2X, 4X, 6X, 8X, 10X, 12X, 14X, 16X, 24X, 32X, 64X, 128X.
AGC
Level 5
Exit
Sens-up
Sens up X4
Exit
Manual shutter
Shutter 1/50
Exit
Manual Iris
Iris 100….………|
Exit
20
9 Additional menu:
(1) User preset setup: On / Off
8 User preset number, 1~8.
User Preset mode: use direction keys to “On” and press “Iris/Open” to setup.
User preset mode
Focus
Exposure
Other
User Preset
User preset number No 1
User preset mode Off
Save
Clear
Exit
preset not setup.
Additional menu
User setup Off
Privacy zone mask Off
Day & Night Auto 1
Sync. system Internal
Image adjustment
Exit
21
Focus: Using direction keys to “Focus” and press “Iris/Open” key to set up.
Other：Refer to below details.
(2) Privacy mask
Group selection：1~ 8
Area selection: 1~ 4 zones / group
Zone mode: On / Off
Focus
Mode Auto
Zoom trace mode On
Zoom trace speed Fast
Digital zoom On
Show zoom Off
Exit
Privacy mask
Group selection 1
Area selection 1
Zone mode Off
Color 50…|..……….
Top 50…|..……….
Bottom 104….…|…….
Left 50…|.……….
Right 98….……|….
Exit
Other
Camera Type Off
BW Auto trace BW
BLC Off
Motion Detection Off
Privacy mask Off
Day & Night Outer
Horizontal flip Off
Vertical flip Off
Exit
22
Color: Color, range of privacy zone is 0~100.
Top: Ordinate position on the top of zone.
Bottom: Ordinate position on the bottom.
Left: Horizontal abscissa position on the left side.
Right: Horizontal abscissa position on the left side.
(3) Day / Night: Day and Night function. Auto 1/ Auto 2 / Outer/ Color/ B&W mode.
B&W mode: Suit for night work.
Color mode: Suit for daytime.
Auto mode: Change day and night mode automatically according to the environment
illumination. Auto 1 is faster than Auto 2.
(4) Synchronous mode: internal, unchangeable.
(5) Image adjustment.
Freeze: Camera starts freezing the image of start point, as soon as camera stops at preset end
point, camera starts display live images.
Horizontal flip: image will flip 180°when you start up. Normal when shutdown.
Vertical flip: image will flip 180°when you start up, and normal when shutdown.
Sharpness: adjust the sharpness of the edges. Range: 0~31.
Hue: adjust the image hue, range: 0~100.
Re-boot: restart the camera.
Exit: Exit camera menu.
Sharpness
Sharpness 8…|.……….
Exit
Image adjustment
Freeze Off
Horizontal flip Off
Vertical flip Off
Sharpness On
Hue 50….…|…….
Exit
23
4.2.6 Cruise Setting
Auto cruise: set up preset scan route.
<Dwell Time (Sec)>: preset cruise dwell time, range:1～250 Sec.
<Preset List>: (3 pages) 30 presets.
<1234567890>：preset position in the preset list.
<110111 1111>：1 means the preset position corresponding to above preset list is selected to
cruise list; 0 means overleap.
<Back>：save the setup and back to main menu.
<Exit>：Exit OSD menu.
4.2.7 Display Setup
Display setup: On/Off, set up the orientation display or not.
4.2.8 Restore Factory Default
Move cursor to <RESTORE FACTORY DEFAULT> and press “Iris/Open to restore factory
default.
4.2.9 Reboot System
Move cursor to <Reboot System > and press “Iris /Open” to reboot the system. Easy to
change the Soft/Hard addresses by remote and no need to power off.
4.2.10 Exit: Move cursor to <Exit> and press “Iris /Open” to exit the OSD menu.
CRUISE
DWELL TIME<SECS> 6
PRESET LIST 1
1 ON 0 OFF
1234567890 PRESET
1101111111 [1-10]
BACK
EXIT
236/163 X1
Horizontal /Vertical Zoom
24
Trouble Shooting
Troubles
Reason
Solution
No action, no
image after
power on
Connect wrong cable.
Correct the connection
Power supply damaged.
Change
Bad connection.
Eliminate the bad connection
Out of control
after power up
Maybe user setup wrong IP,
Protocol and Baud rate.
Reset IP, Protocol and Baud rate.
RS-485 cable reverses connection
or disconnection.
Check RS-485 connection cable.
Screen not
stable
Video cable is bad connection
Eliminate the bad connection
Power is not enough.
Change
Discontinuity
while work
RS-485 cable is bad connection or
disconnection.
Check RS-485 connection cable.
RS-485 cable broken.
Check RS-485 connection cable.
25
Safety Information
1. Transportation
Do not force, shake and marinate during transportation, storage and installation.
2. Installation
Please handle with care, do not press the camera and its’ parts when you install, do not connect
before you install the cover.
3. Power cable, Video cable and control cable.
Use shield wire and do not mix with other cables.
4 Electrical safeties
Keep the camera or signal transmission wire away from high voltage equipment or cable (at
least 50 meters), take lightning protection and surge protection.
5. Clean
When cleaning, use dry and soft cloth or neutral cleanser to clean the camera cover.
6. Must be sealed closely, do not spray water or liquid onto parts of camera, doing so may
cause damage.
7. Do not use the camera in extreme temperature or humidity environment.
8. Do not install the camera close to air outlet of air condition.
Camera lens will be misty because of water condensation under below conditions:
Extreme temperature change.
The room full of smoking or dust.
9. Do not locate the camera towards extremely bright objects such as sun and spotlight, as this
may damage the CCD image sensor.
Loading...