Provision ISR Ultra-Z-18s, Ultra-Z-36s, Ultra-Z-28s User Manual

Download

Contents

Before insta lli ng

Key features

Configure, fix and wire...............

Basic speed dome operation........

Programmin g the s peed dome

Parts and dime nsi ons

Wiring schem ati c

Specificat ion s

New features..................

Before installing

Installation should be carried out only by qualified personnel and in accordance with

any wiring regulations in force at the time.

The speed dome is heavy and could cause injury if not correctly mounted in

accordance with these instructions. Use only the fittings supplied with the speed dome and ensure that all lanyard safety cables are connected correctly during installation.

Adequate protection against lightning strikes and power surges must be installed to

prevent damage to the speed dome. Any safety warnings on the product and in these instructions must be adhered to. If cleaning is necessary

, disconnect power to the speed dome first. Do not use abrasive cleaners, as these will cause damage to the cover and cause poor image quality. Use a damp cloth to gently clean the dome cover and dry off with a soft clean cloth.

Do not use any brackets, mounts or other accessories not specifically designed for

use with this speed dome.

Do not attempt to service or repair the speed dome as opening or removing covers

may expose dangerous voltages or other hazards. Refer all servicing to qualified service personnel.

Key features

Presets

Pattern tours

AUTO SCAN between 2presets

Group function

Up to 127 sets of positional and zoom level information can be stored as presets. These can be called manually by the operator, automatically by an alarm input, or grouped to form a sequence of actions to run automatically. Each preset can also be programmed with the following:

Any dome movement can be recorded - and subsequently played back - as four separate pattern tours. These can be played back individually or grouped to form a sequence of tours.

AUTO SCAN isausefulfeaturewhen,forexample,theoperatorwishesto‘patrol’a perimeter fence. If one preset is defined at one end of the fence and a

second preset is defined at the other, the scan function will smoothly and accurately move from one end to the other and then back again in a repeating sequence. Speed can be adjusted as necessary and up to 8 scan functions can be defined.

The group function is a powerful feature which allows the operator to define a sequence of speed dome actions to form an automatic patrol sequence. Actions can be a mix of preset positions, pattern tours and scan functions. Up to 8 groups can be defined and each group can have up to 20 actions which repeat indefinitely until interrupted by the operator or an alarm input. Specific parameters such as preset speed, dwell time and action loop can also be specified

Alarm action - relay outputs can be triggered when particular presets are called

Title - each preset can be titled with up to 10 characters so that zones can easily be identified

Privacy zones

Alarm inputs and outputs

On Screen Display (OSD)

Powerful park function

By defining a privacy zone, sensitive scenes such as windows can be masked off so they cannot be viewed by the operator. Up to 8 privacy zones can be defined. Privacy zone size adjusts automatically depending on the speed dome zoom level.

This speed dome has 8 alarm inputs and 4 alarm outputs. Any alarm input can be set to call a predefined preset, scan function, pattern or group. Any preset can be configured to activate any or all of the alarm outputs. For example, a PIR detector connected to alarm input 1 could call preset 7 to view that particular scene whilst activating an external lamp connected to relay 1 and an external siren connected to relay 3.

The operator can choose if any or all of the following information is displayed on screen during normal speed dome operation.

TimeandDate

The speed dome also has a full on screen menu setup allowing quick and easy configuration of all the speed dome features.

The speed dome can be configured to run a specified VST function, pattern tour, group or preset after a defined period of inactivity.

Preset status and title Speed dome position coordinates and zoom level Alarm I/O status

Speed dome ID

New features

1. Special Preset setting The u ser coul d set the pa ramet er s of focu s Mode, C olor, W DR ,

St a bili zer, Au t o s l ow s hut t er, W h ite Ba l ance , AE M ode acco rding to differ en t scene o n each preset , in thi s case, t h

came ra can alwa ys give the b est pictu re qualit y.

2. Nest G roup One group c ould nest an other gr oup, o ne g roup c ould o nly be nest ed once.

3. Sch edule fun ction

The us er c ould set a sc he dule to mak e the speed d om e run differ en t fun ctions( such as pres et , pat tern, g roup, auto s can) at differ en t time. U p to 7 sched ul es can be d ef ined.

4. sof t camera ID

The use r cou ld ad just the cam era ID by keybo ard, no need to proc ess on dip sw itch.

5. Fir mware up datin g and baut ra te adj ustin g could be pr oc essed

in jun ction b ox conven iently, no n ee d to op en the s peed do me hous ing.

6. Pel co D/P and AD prot oc ol are av ailable .

7. Full d uplex RS4 22 and semi deplex RS 485 por t ar e avail ab le. The user co uld s el ect d if fe rent co mmuni ca tion mode by adjusting

dip sw itch.

8. Powerful lightning proof design could resist up to 20KV lighting or surge.

9. Powerful power supply design

10?. Password protection

The user could set a pass word fo r t he speed dome to pr ev ent

unpe rmitted p rocessi ng.

Configure, fix and wire

1. Remo ve the foam pack ing pieces

2. Reas semble the spe ed dome

Befo re procee ding with i nstalla tion, the s peed dome f oam pac ki ng piec es must be re moved. Re move the ou ter dome co ver with th e tool supp lied and ca refully r emove the f oam packi ng piec es . When hand ling the do me cover, al ways wear t he gloves s uppli ed t o avoid gett ing finge rprints o n the outer d ome cover.

Refi t the black i nner dome c over and ou ter dome co ver. If the lany ard safet y wire was re moved, it m ust be refi tted befo re the dome cove r is fixed.

Foam

1. Wearing the gloves and using the supplied

tool, remove the outer dome cover.

2. Remove the foam pieces from the camera module.

Foam

3. Fix th e bracket

1. Fix the supplied mounting template, taking account of any pipework, cables, overhangs etc. that may obstruct the bracket once fitted.

3. Remove the junction box cover. Using the supplied bolts and tool, firmly fix the bracket.

Pendent option

5. Bring the speed dome up to the bracket.

4. Feed the speed dome cable through the bracket.

2. After making suitable checks for buried pipes and cables, drill fixing holes suitable for the bolts supplied with the speed dome.

Lanyard

6. Tighten the three screws to fix the speed dome and ensure the lanyard safety chain is properly connected.

Cover

Lanyard

3. Carefully unclip the black inner dome

4. Complete the install

Proto col & Baud rate DI P switch table

Speed d ome ID DIP switch table

Note : ID 0 s hould not b e us ed. Whe re m ultiple s pe ed domes are co nn ected, a un ique ID mus t be a ssigned t o ea ch one. Dip sw it ches 9-10 a re reserv ed a nd must n ot b e changed .

1 2 3 4 5 6 7 8

Fact ory defau lt

swit ch positi ons

Spee d dome ID is se t

usin g standar d bina ry notati on

1 2 3 Pro to co l/R at e

OFF OFF O FF P elc oD , 00 b ps OFF ON OF F

AD,48 00 b ps

ON ON OF

C,960 0 bp s

OFF OFF O

elcoP,9 600 bps

ON OFF O

elcoP,4 800 bps

OFF ON O ON ON ON Pe lc oD, 00 b ps

Note: D ip s witch es 4 -6 are re se rve d and mus t no t be chan ge d.

1 2 3 4 5 6 7 8 9 10 DIP 1 2 4 8 16 32 64 1 28 – – VA L/ ID

ON OFF OF F OF F OFF O FF O FF O FF OFF ON OF F OF F OFF O FF O FF O FF – – 2 ON ON OFF O FF O FF OF F OF F OF F – – 3 OFF OFF O N OF F OFF O FF O FF O FF – – 4 ON OFF ON O FF O FF OF F OF F OF F – – 5 OFF ON ON O FF O FF OF F OF F OF F – – 6 ON ON ON OF F OF F OFF O FF O FF – – 7 OFF OFF O FF O N OFF O FF O FF O FF – – 8

– – – – – – – – – – –

ON ON ON ON O N ON O N ON 255

– – 1

ip4 res er ved

Dip5 Rs 48 5/Rs4 22

Dip6 NT SC /Pal

P P

AD,48 00 b ps

N N N

If ther e’s a problem at this sta ge...

6. Verify basic operation

…work through the logical steps below to determine and rectify the problem

- check the PCB to make sure the red power LED is lit. If not, check that the PSU is correctly connected and has power. If you have a test meter, verify that the output of the PSU is approximately 24V AC.

If the power LED is lit, check the BNC crimp connection is correctly made at both the PCB end and the DVR / monitor / matrix end. A portable test monitor connected directly to the video output of the speed dome is also a useful test - if a picture is displayed, double check the BNC connections and the signal cable used.

- check that the control equipment you are using is compatible with the speed

dome and is configured to match the speed dome settings correctly.

If dip switches were changed on the speed dome, check the power on self test screen to ensure that protocol, ID and baud rate are as expected.

If the settings match, you should check the polarity of the connections, both on the control equipment and the speed dome. If you suspect there is a polarity issue, swap the A & B wires at the speed dome to see if this resolves the problem.

Check also that there are no other telemetry devices on the system with the same ID as the speed dome. If in doubt, connect the speed dome directly to the PTZ controller and isolate all other equipment.

No picture

No PTZ control

1. After carefully checking the installation, including all cable connections, apply power to the dome and check that the startup and self test screen is displayed.

2. After the self test is complete, the dome starts normal operation. Verify that there is basic PTZ control from your control equipment.

H IGH S P E E D D O M E

- --- - - - - - - - - - - --- - - - - - - F IRM W A R E V E R C OLO U R S Y S T E M P ROT O C O L A DDR E S S B AUD R A T E C omm . M o d e Z OOM M O D U L E A LAR M I / O

H OME T E A C H I N G . .

O :-- - -

I :12 3 4 5 6 7 8

: 1.0SY28V : P AL : P ELC O - D : 1 : 2 400 : R S48 5 / 4 2 2 : O K : O K

W AIT . . .

1 4:4 6 : 4 6

5. Complete the install

1a - wall bracket option. After making all the connections to the PCB, fit the junction box cover with the four screws.

Note: when fixing the cover to the junction box, ensure that the seal is also fitted properly and that none of the cables are trapped

1b - pendent option. After making all the connections to the PCB, raise the dome assembly to the junction box, connect the dome cable to the PCB and fix with the four screws.

Seal

Note: when fixing the cover to the junction box, ensure that the seal is also fitted properly and that none of the cables are trapped

C A M 1 3 2 5/37/ x 1

11-07-15

11-07-15 0 9 : 3 7 : 1 5

O : - 2 3 -

I : 1 2 3 4 5 6 7 8

P RES E T 003

P R E S E T 3

P ARK I N G B A Y 1

R E C E P T I O N

Basic speed dome operation

Progr amming, call ing and deleting presets

Under standing the On Screen Display (OSD)

Ther e are many di ff er ent PTZ k ey board s and DVR sys tems capa ble of con trollin g this spee d dome, and i t would be im possibl e to desc ribe them a ll here. Ther efore, ex amples gi ven in the fo llowing page s are based o n the more po pular con trol equi pment a va ilabl e. Whil st the prin ciples of o peratio n are the sam e, regard less of the cont rol equip ment used , referen ce may need t o be made to th e manu al suppli ed with you r particu lar contr ol equi pm ent.

To program a preset position, move the speed dome to the desired scene and zoom level and press:

Where is a preset number between 1 & 128 (but note that preset 95 is reserved and cannot be used). Confirmation is displayed on the OSD.

SET - XXX - ENTER

XXX

To delete a preset position, press:

Where is a preset number between 1 & 128 (but note that preset 95 is reserved and cannot be used). The preset position is cleared from memory.

CLEAR - XXX - ENTER

XXX

To reprogramme a preset position, follow the steps for programming a preset - it is not necessary to delete the old preset position first

PRESET LABEL: If defined, is displayed when a preset position is called

ALARM I/O: Shows which alarm inputs and outputs are active

TE/CLOCK: Shows

current time and date

PTZ INFORMATION: The current pan/tilt position in degrees and the current zoom level

ACTION TITLE: Shows current speed dome action

To go to a preset position thats already been programmed, press:

SHOT - XXX - ENTERXXX - Preset

Where is a preset number between 1 & 128 (but note that preset 95 is reserved and cannot be used). The speed dome moves to the preset position. Confirmation and preset title (if defined) is displayed on the OSD.

XXX

O :-- - -

I :12 3 4 5 6 7 8

O :-- - -

I :12 3 4 5 6 7 8

11-07-15 1 2:3 8 : 0 5

11-07-15 1 2:4 2 : 2 2

CAMERA ID: Shows the current ID as defined by the

dip switch settings

CAM001 307/46/×003

Preset001

CAM001 325/37/×001

CAM001 325/37/×003

Displ ay setup

DATE TIME SETUP

Syste m informatio n

The sp eed dome se tup menu al lows the op erator to c ustomis e and prog ram all asp ects of spe ed dome ope ration. Al l menu se tt ings ar e reta ined in non -volati le memory s o if power is l ost to the sp eed dom e for an y reason, a ll settin gs will be re tained.

MA I N M E NU

-- - - - -- - - -- - - -- - - - -- - - -- - - -- <S Y S T EM I N F OR M A TI O N > <D I S P LA Y S E TU P > <D O M E C AM E R A SE T U P> <A L A R M SE T U P>

EX I T

DI S P L AY S E T UP

-- - - - -- - - -- - - -- - - - -- - - -- - - -- CA M E R A ID

PT Z I N F OR M A TI O N PR E S E T LA B E L AL A R M I /O DA T E / TI M E <D A T E T IM E S E TU P > BA C K EX I T

AC T I O N TI T L E

DA T E / TI M E S ET U P

-- - - - -- - - -- - - -- - - - -- - - -- - - -- DA T E 0 7 -0 1 - 07 / S UN TI M E 1 4 :3 7 : 15

BA C K EX I T

SY S T E M IN F O RM A T IO N

-- - - - -- - - -- - - -- - - - -- - - -- - - -- -

FI R M W AR E V E R CO L O U R SY S T EM PR O T O CO L AD D R E SS BA U D R A TE Co m m . MO D E R S4 2 2 /R S 4 8 5

BA C K EX I T

To access the speed dome setup menu, key:

To navigate the main menu, move the joystick up / down to choose a menu item or change settings within a menu item.

To enter a menu item or confirm a new setting, key:

To exit a menu item or cancel a new setting, key:

Where a menu item is surrounded by brackets, it indicates that there is a sub menu.

Where a menu screen shows , selecting this option will exit the menu and the speed dome will return to normal operation. Where a menu screen shows , selecting this option will return to the higher menu level.

The main menu has five options:

- Provides information such as firmware version, protocol and ID values as defined by the dip switch settings.

SHOT - 95 - ENTER

NEAR

FAR

EXIT

BACK

- Allows the operator to specify which On Screen Display information is shown during normal operation. Also allows privacy zones to be defined and time/date to be changed

- Allows all operating features of the speed dome to be programmed and managed. Also allows settings for the camera module to be changed

- Allows a password

to be set to protect the speed dome setup

- Allows various speed dome settings to be reset to factory defaults

From the main menu, use the joystick to highlight and key:

To return to the main menu, highlight and key:

To exit the setup menu completely, highlight

and key:

SYSTEM INFORMATION

NEAR

BACK

NEAR

EXIT NEAR

From the main menu, use the joystick to highlight and key:

- shows camera ID according to the DIP switch settings, eg CAM 1.

- shows

current speed dome action, eg PRESET3.

shows the current pan / tilt position in degrees and the current zoom level.

- shows

preset title (if defined) when a preset is called.

- shows real time

status of the alarm inputs and outputs.

- sub menu to change

the date and time

- sub menu to setup the

speed dome privacy zones

Highlight the item to modify and key: Use the joystick to change the setting and key:

to save or: to cancel.

DISPLAY SETUP NEAR

CAMERA ID (ON / OFF)

ACTION TITLE (ON / OFF / AUTO)

PTZ INFORMATION (ON / OFF / AUTO)

PRESET LABEL (ON / OFF / AUTO)

ALARM I/O (ON/OFF)

<DATE TIME SETUP)

NEAR

NEAR FAR

Note: If the auto option is chosen, the relevant information is displayed for a few seconds before disappearing.

From the display setup menu, use the joystick to highlight and key:

Highlight the item to modify and key: Move the joystick up and down to change an

individual value and left and right to move to the previous / next value

DATE/TIME SETUP

NEAR

: PA L : PE L C O -D : 00 1 : 24 0 0

ON / O F F

ON / O F F/ A U TO ON / O F F/ A U TO ON / O F F/ A U TO

ON / O F F/ A U TO

Programming the speed dome

1.0SY28V

: 2.5W036V

CA M E R A SE T U P1

-- - - - -- - - -- - - -- - - - -- - - -- - - -- -

FO C U S M OD E CO L O U R

BA C K EX I T

DI G I T AL Z O O M

DO M E C A ME R A S ET U P

-- - - - -- - - -- - - -- - - - -- - - -- - - -- <C A M E RA S E T UP 1 >

BA C K EX I T

From the main menu, use the joystick to highlight and key:

- setup of specific camera module features.

- setup of the pan / tilt / zoom operation of the speed dome, park action configuration, and configuration of the alarm inputs.

- full management and

programming of individual presets.

- full management and

programming of SCAN functions.

- full management and

programming of pattern tours.

Highlight the setup menu required and key:

DOME CAMERA SETUP

NEAR

<CAMERA SETUP1>,

NEAR

Remember: A menu item surrounded by brackets shows it has a sub menu.

- full management and

programming of group functions.

- full management and

programming of Schedule.

From the dome camera setup menu, use the joystick to highlight and key:

MANUAL - the operator must focus the camera manually using the NEAR and FAR keys.

SEMIAUTO - the camera automatically focuses during normal PTZ movement but preset focus information is stored when a preset is programmed and recalled each time the preset is called

AUTO - the module auto focuses continually

- switches the module

between colour and b/w mode

- sub menu to change

the white balance settings

- sub menu to change the auto

exposure settings

CAMERA SETUP1

NEAR

FOCUS MODE

COLOUR (ON/OFF)

DIGITAL ZOOM (ON / OFF) - disables or

enables the 10x digital zoom. When disabled, the maximum zoom level is 36x (optical).

Dome ca mera setup

Camer a setup1

Priva cy zone

Edit zone

PR I V A C Y ZO N E

-- - - - - -- - - - -- - - - -- - - - -- - - - - -ZO N E N O .

ZO N E D I S PL A Y CL E A R Z O NE <E D I T Z O NE >

BA C K

ED I T Z O NE 1

-- - - - -- - - -- - - -- - - - -- - - -- - - -- -

MO V E T O T AR G E T PO S I TI O N [N E A R :S E L EC T / FA R : C AN C E L]

ED I T Z O NE 1

-- - - - -- - - -- - - -- - - - -- - - -- - - -- -

[L / R : AD J U ST Z O N E WI D T H ] [U / D : AD J U ST Z O N E HE I G H T]

[N E A R :S A V E /F A R :C A N C EL ]

From the display setup menu, use the joystick to highlight and key:

shows the privacy zone

currently being modified.

- determines whether the privacy

zone is displayed during normal operation.

- allows the operator to define

the privacy zone.

Highlight the item to modify and key: Use the joystick to change the setting and key:

to save or: to cancel.

PRIVACY ZONE NEAR

ZONE NO. (1-8) -

DISPLAY

NEAR

NEAR FAR

From the privacy zone menu, use the joystick to highlight and key:

Use the joystick to move the speed dome to the approximate position and zoom level for the privacy zone and key: to select or

to cancel and return to the privacy zone

menu.

EDIT ZONE NEAR

NEAR

FAR

ON / O F F CA N C E L/ Y E S

ON / O F F AU T O ON / O F F

Move the joystick left and right to finely adjust the width of the privacy zone and up and down to finely adjust the height.

To save the privacy zone, key: or key:

to cancel.

NEAR

FAR

EXIT

MIRROR

ON / O F F

PIC EFFECT

OFF/NEG/B/W

SLOW AE

001-048

WB mode s etup

Auto ex posure setup

WB M O D E S ET U P

-- - - - -- - - -- - - -- - - - -- - - -- - - -- -

WB M O D E

RE D A D J US T BL U E A D JU S T

BA C K EX I T

AE S E T U P

-- - - - -- - - -- - - -- - - - -- - - -- - - -- BL C DA Y / N IG H T AE M O D E

IR I S L E VE L GA I N L E VE L SH U T T ER S P D BR I G H TN E S S

BA C K EX I T

From the zoom camera setup menu, use the joystick to highlight and key:

AUTO - the speed dome determines the optimum white balance settings for a given scene

MANUAL - the operator can adjust white balance settings manually

iNDOOROUTDOORATW-

- in manual mode, the red

colour content can be adjusted

- in manual mode, the blue

colour content can be adjusted

WHITE BALANCE SETUP

NEAR

WB MODE (AUTO/ INDOOR/OUTDOOR/ATW)

RED ADJUST

BLUE ADJUST

MANUAL

From the zoom camera setup menu, use the joystick to highlight

and key:

- The operator can select BLC(Back Light Compensation) mode, selecting will disable this feature.

- the operator can choose to fix the camera in to DAY (colour) or NIGHT (B&W with IR cut filter mode). In AUTO mode, the camera switches between DAY and NIGHT depending on the surrounding light level

- in AUTO mode, the speed dome determines optimum camera exposure settings for a given scene. In modes other than AUTO, the operator can adjust specific exposure characteristics to suit a particular scene

Highlight the item to modify and key: Use the joystick to change the setting and key:

AUTO EXPOSURE

SETUP NEAR

BLC (OFF/ ON)

DAY/NIGHT (AUTO/DAY/NIGHT)

AE MODE

NEAR

OFF

AU T O

-- -

ON AU T O AU T O

-- -

CA M E R A SE T U P2

-- - - - -- - - -- - - -- - - - -- - - -- - - -- PI C F R E EZ E PI C F L I P ZO O M S P EE D FL I C K ER N E SS WD R AU T O S L OW S H U TT E R ST A B A LI Z E R

BA C K EX I T

OF F ON 7 OF F

OFF/ON/AUTO/ON-R/ON-D

OF F ON/OFF/HOLD

From the dome camera setup menu, use the joystick to highlight and key:

- when set to ON, there’s no

image flash.

- when set to ON, the image will be

turned 180 degrees.

- Operator can select zoom

speed.

- Should be set to ON when used in certain lighting conditions (EG Fluorescent lighting) to prevent picture flicker.

- Used to select

shutter speed

Highlight the item to modify and key: Use the joystick to change the setting and key:

to save or: to cancel.

MOTION SETUP

NEAR

PIC FREEZE

PIC FLIP

ZOOM SPEED

FLICKERNESS

AUTO SLOW SHUTTER

NEAR

NEAR FAR

Camer a setup2

Motio n setup

MO T I O N SE T U P

-- - - - -- - - -- - - -- - - - -- - - -- - - -- AU T O F L IP JO G S P E ED JO G D I R EC T I ON PW R U P A C TI O N ZO O M P R OP O R TI O N AL PR E S E T LO C K

BA C K EX I T

ON SL O W NO R ON ON OF F

From the dome camera setup menu, use the joystick to highlight and key:

- when set to ON, the speed dome will resume its last operation when power is restored after a power failure

Highlight the item to modify and key: Use the joystick to change the setting and key:

to save or: to cancel.

MOTION SETUP

NEAR

PWR UP ACTION

NEAR

NEAR FAR

AUTO FLIP (ON / OFF)

JOG SPEED

JOG DIRECTION (INVERSE / NORMAL)

<ZOOM PROPORTIONAL> -

PRESET LOCK

- when set to ON, the dome will flip 180 degrees when the tilt position reaches 90 degrees.

- determines the maximum speed in degrees / second the dome will move during manual operation

when set to normal, the pan direction is opposite to the joystick movement.

used to select

zoom proportion.

- Configure actions that run automatically after a defined period of inactivity

- when set to ON, preset programming directly from the keyboard is disabled to prevent tampering

3DNR ON/OFF

STABLE ZOOM

ON/OFF

PR E S E T SE T U P

-- - - - -- - - -- - - -- - - - -- - - -- - - -- PR E S E T NO .

BA C K EX I T

CL EAR P R E SE T

00 1

CA N C E L

From the dome camera setup menu, use the joystick to highlight and key:

- The preset number currently being modified. If the preset number is already defined, the speed dome will move to that preset position, otherwise UNDEFINED is displayed under the preset number

- use this option to program

the preset position

- use to edit the preset label.

Highlight the item to modify and key: Use the joystick to change the setting and key:

to save or: to cancel.

PRESET SETUP

NEAR

PRESET NUMBER (1 - 128)

NEAR

NEAR FAR

This option is only available when the selected preset position is already programmed

CLR PRESET

- use to program camera

status for each preset.

- use this option to delete the

current preset position

From the preset setup menu, use the joystick to highlight and key:

Using the joystick, move the speed dome to the desired position and zoom level and key:

to save or: to cancel.

EDIT SCENE NEAR

NEAR FAR

Prese t setup

Park ac tion setup

PA R K A C TI O N S ET U P

-- - - - -- - - -- - - -- - - - -- - - -- - - -- PA R K E N AB L E WA I T T I ME PA R K A C TI O N

BA C K EX I T

NO T E : P AR K T I ME U N I TS I S S E C ON D S

OF F 00 : 1 0 :0 0 HO M E

From the motion setup menu, use the joystick to highlight and key:

- when set to ON, the speed dome will run the specified park action after the wait time has elapsed

- can be set between one minute and 4 hours. If no manual control occurs during this time, the park action will run

- choose the action to run after the wait time has elapsed. This can be return to home position, go to a preset or run a SCAN, GROUP or PATTERN TOUR

Highlight the item to modify and key: Use the joystick to change the setting and key:

to save or: to cancel.

PARK ACTION SETUP

NEAR

PARK ENABLE

WAIT TIME

PARK ACTION

NEAR

NEAR FAR

From the motion setup menu, use the joystick to highlight and key:

- YES/CANCEL

for each preset, specifies the camera setting. f

Focus mode - AUTO/SEMIAUTO/MANUAL

Highlight the item to modify and key: Use the joystick to change the setting and key:

to save or: to cancel.

PRESET DEFAULTS

NEAR

Preset defaults

NEAR

NEAR FAR

ollowing items are available only when

YYY YYY YYYYYY YYYUyes is selected.

MANUAL - the operator must focus the camera manually by joystick movement using the ZOOM IN and ZOOM OUT keys.

SEMIAUTO - the camera automatically focuses during normal PTZ movement but preset focus information is stored when a preset is programmed and recalled each time the preset is called.

AUTO - the module auto focuses continually

MOTION DETECTION OFF/ <ON>

Motion position setup

-- - - - -- - - -- - - -- - - - -- - - -- - - -- -

USE U/D/L/R ADJUST THE POSITION

USE NEAR TO SELECT

Motion position setup

-- - - - -- - - -- - - -- - - - -- - - -- - - -- -

USE U/D/L/R ADJUST WEIGHT AND HEIGHT USE NEAR TO SELECT

Motion position setup

Move to position setup

Move to positon setup

-- - - - -- - - -- - - -- - - - -- - - -- - - -- -

USE U/D/L/R ADJUST

USE NEAR TO SELECT

MOVE TO POSITION

077/05 X005

ED I T S CE N E - P R ES E T 0 01

-- - - -- - - - -- - - -- - - -- - - -- - - - -- -

MO V E T O S TA R T P OS I T IO N [N E A R: S A V E /F A R :C A N CE L ] CA M 0 0 1 O :- - - 00 6 / 02 X 0 0 1 I :- - - -

From the preset setup menu, use the joystick to highlight and key:

Using the joystick, move the speed dome to the desired position and zoom level and key:

to save or: to cancel.

EDIT SCENE NEAR

NEAR FAR

Edit sc ene

ED I T S CE N E - P R ES E T 0 01

-- - - -- - - - -- - - -- - - -- - - -- - - - -- -

MO V E T O S TA R T P OS I T IO N [N E A R: S A V E /F A R :C A N CE L ] CA M 0 0 1 O :- - - 00 6 / 02 X 0 0 1 I :- - - -

From the preset setup menu, use the joystick to highlight and key:

Using the joystick, move the speed dome to the desired position and zoom level and key:

to save or: to cancel.

EDIT SCENE NEAR

NEAR FAR

Preset defaults

PRESET DEFAULTS PR E - 0 01

-- - - - -- - - -- - - -- - - - -- - - -- - - -- CLEAR DEFAULTS CANCEL

BA C K EX I T

FO C U S M OD E A U TO CO L O U R ON WD R ON/OFF/AUTO/ON-R/ON-D ST A B A LI Z E R ON/OFF/HOLD AE-SLOW SHUTTER OFF <W H I T E BA L A NC E > <A E M O D E>

From the motion setup menu, use the joystick to highlight and key:

- YES/CANCEL

for each preset, specifies the camera setting. f

Focus mode - AUTO/SEMIAUTO/MANUAL

Highlight the item to modify and key: Use the joystick to change the setting and key:

to save or: to cancel.

PRESET DEFAULTS

NEAR

Preset defaults

NEAR

NEAR FAR

ollowing items are available only when

YYY YYY YYYYYY YYYUyes is selected.

MANUAL - the operator must focus the camera manually by joystick movement using the ZOOM IN and ZOOM OUT keys.

SEMIAUTO - the camera automatically focuses during normal PTZ movement but preset focus information is stored when a preset is programmed and recalled each time the preset is called.

AUTO - the module auto focuses continually

Edit la bel

PR E S E T LA B E L SE T U P

-- - - - -- - - -- - - -- - - - -- - - -- - - -- LA B F O R P RE [ ]

-- - - - -- - - 12 3 4 5 67 8 9 0 AB C D E FG H I J KL M N O PQ R S T UV W X Y Z SA V E C A NC E L CL E A R C AN C E L

BA C K EX I T

From the preset setup menu, use the joystick to highlight and key:

The solid white square shows the current cursor position.

The flashing white square shows the currently selected character.

Move the joystick up / down / left / right to choose the required character and key: to insert it in the preset label. The solid white square moves to the next cursor position. Repeat until the preset label is complete.

If a mistake is made, use the joystick to select the backspace ( ) and key: . The cursor moves back one square.

Select to save the preset label or

to lose changes, and key: to

exit

EDIT LABEL NEAR

NEAR

CANCEL NEAR

From the dome camera setup menu, use the joystick to highlight and key:

shows the SCAN number

currently being modified.

- any defined preset between 1 &

127.

- any defined preset between 1

&127.

- determines the speed of movement in degrees per second between each preset position.

- deletes the currently selected SCAN function.

- runs the currently selected

SCAN function for testing purposes

Highlight the item to modify and key: Use the joystick to change the setting and key:

to save or: to cancel.

SCAN SETUP

NEAR

SCAN NO. (1-8) -

1ST POS.

2ND POS.

SCAN SPEED

CLEAR SCAN

RUN SCAN

NEAR

NEAR FAR

Note:AV VSCAN always moves anti-clockwise to the 1st position and then clockwise to the 2nd position.

AUTO SCAN Setup

vVST SE T U P

-- - - - -- - - -- - - -- - - - -- - - -- - - -- SCAN NO. 1S T P O S . 2N D P O S . SCAN SPEED DI R E C TI O N CLEAR SCAN RUN SCAN

BA C K EX I T

1/ 8 NO N E NO N E 30 / S E C NO R M A L CA N C E L

WB mode s etup

Auto ex posure setup

WB M O D E S ET U P

-- - - - -- - - -- - - -- - - - -- - - -- - - -- WB M O D E

RE D A D J US T BL U E A D JU S T

BA C K EX I T

AE S E T U P

-- - - - -- - - -- - - -- - - - -- - - -- - - -- BL C DA Y / N IG H T AE M O D E

IR I S L E VE L GA I N L E VE L SH U T T ER S P D BR I G H TN E S S

BA C K EX I T

From the zoom camera setup menu, use the joystick to highlight and key:

WHITE BALANCE SETUP

NEAR

From the zoom camera setup menu, use the joystick to highlight

and key:

The operator can select BLC(Back Light Compensation) mode, selecting will disable this feature.

- the operator can choose to fix the camera in to DAY (colour) or NIGHT (B&W with IR cut filter mode). In AUTO mode, the camera switches between DAY and NIGHT depending on the surrounding light level

Highlight the item to modify and key: Use the joystick to change the setting and key:

AUTO EXPOSURE

SETUP NEAR

BLC (OFF/ ON)

DAY/NIGHT (AUTO/DAY/NIGHT)

AE MODE

NEAR

OFF

AU T O

-- -

ON AU T O AU T O

-- -

Preset-001

AWC- the speed dome determines the optimum white balance settings for a given scene

MANUAL - the operator can adjust white balance settings manually

iNDOOR- indoor mode OUTDOOR-outdoor mode ATW-auto trace white balance mode

- in manual mode, the red

colour content can be adjusted

- in manual mode, the blue

colour content can be adjusted

WB MODE

RED ADJUST

BLUE ADJUST

3DNR ON/OFF

From the dome camera setup menu, use the joystick to highlight and key:

shows the group number

currently being modified.

- the currently selected group

can be deleted

- runs the currently selected

group for testing purposes

- allows the operator to program the group functions. operator can edit new nesting group action in each group

Highlight the item to modify and key: Use the joystick to change the setting and key:

to save or: to cancel.

GROUP SETUP

NEAR

GROUP NO. (1-8) -

CLEAR GROUP

RUN GROUP

NEAR

NEAR FAR

From the group setup menu, use the joystick to highlight and key:

To edit the group, key: again

Header explanation:

- the item number (between 1 & 20)

- the specific action for this item

- the action number (eg if ACTION is set

to PRESET, this value can be between 1 &128

- the amount of time before the next

action in the list is called

- for PRESET actions, this value is the speed at which the dome moves to the preset. For SCAN and PATTERN, this value is the number of times the action is repeated before the next action is called

Move the joystick up and down to choose the group item to modify and key: The ACTION is highlighted in white

Move the joystick up and down to change the action type between NONE, PRESET, SCAN and PATTERN.

Move the joystick left and right to select and edit values for AAA, DWELL & OPT.

EDIT GROUP NEAR

NEAR

NO ACTION AAA

DWELL

OPT

NEAR.

Key to save this item and continue adding more items as necessary, or key to exit.

NEAR

FAR

Group s etup

Edit gr oup

GR O U P S ET U P

-- - - - -- - - -- - - -- - - - -- - - -- - - -- GR O U P N O.

SA V E G R OU P CL E A R G RO U P RU N G R O UP <E D I T G RO U P >

BA C K EX I T

ED I T G R OU P 1

-- - - - -- - - -- - - -- - - - -- - - -- - - -- -

-- - - - -- - - -- - - -- - - - -- - - -- - - -- 1 PR E S E T 00 1 0 0 :0 3 3 6 0 2 NO N E 3 NO N E 4 NO N E 5 NO N E

-- - - - -- - - -- - - -- - - - -- - - -- - - -- -

BA C K CA N C E L

NO A C T I ON A A A D WE L L O PT

ED I T G R OU P 1

-- - - - -- - - -- - - -- - - - -- - - -- - - -- -

-- - - - -- - - -- - - -- - - - -- - - -- - - -- 1 PA T T E RN 2 PR E S E T 3 SC A N 4 PR E S E T 5 PR E S E T

-- - - - -- - - -- - - -- - - - -- - - -- - - -- -

BA C K CA N C E L [N E A R: E D IT ]

NO A C T I ON A A A D WE L L O PT

1/ 8

CA N C E L CA N C E L

1 5 3

0 4

36 0

11 0

00 : 0 3 00 : 0 8 00 : 0 3 00 : 1 5 01 : 3 0

PA T T E RN S E T UP

-- - - - -- - - -- - - -- - - - -- - - -- - - -- PA T T E RN N O .

CL E A R P AT T E RN RU N P A T TE R N <E D I T P AT T E RN >

BA C K EX I T

1/ 4

CA N C E L

From the dome camera setup menu, use the joystick to highlight and key:

- The pattern number

currently being modified.

- the currently selected

pattern can be deleted

- runs the currently selected

pattern for testing purposes

- allows the operator to

program a patten tour

Highlight the item to modify and key: Use the joystick to change the setting and key:

to save or: to cancel.

PATTERN SETUP

NEAR

PATTERN NO. (1 - 4)

CLEAR PATTERN

RUN PATTERN

NEAR

NEAR FAR

Patte rn setup

ED I T P A TT E R N 4

-- - - - -- - - -- - - -- - - - -- - - -- - - -- -

MO V E T O S TA R T P OS I T IO N [N E A R :S T A RT / F A R: C A N CE L CA M 0 0 1 O :- - 00 9 / 0 6 X0 0 1 I :- - -

ED I T P A TT E R N 4

[N E A R :S A V E /F A R :D E L E TE ]

From the pattern setup menu, use the joystick to highlight and key:

Position the speed dome to the desired starting point and key:

EDIT PATTERN NEAR

NEAR

Move the dome to the various positions and zoom levels required for the pattern. The white squares at the top of the display show remaining storage and disappear as the pattern is recorded.

To save the pattern, key: To abandon pattern programming, key:

NEAR

FAR

Note: Pattern tour memory is only used when movements are recorded. Pauses between movements, regardless of time, do not use pattern tour memory

Edit pa ttern

Sched ule Setup

SC H E D UL E S E TU P

-- - - - -- - - -- - - -- - - - -- - - -- - - -- MA S T E R EN A B LE DA Y T I M E AC T N O .

1 MO N 0 0 : 00 P A T 0 01 2 UN D E F IN E D 3 UN D E F IN E D 4 5 6 7

UN D E F IN E D UN D E F IN E D UN D E F IN E D UN D E F IN E D

BA C K

From the main menu, use the joystick to highlight and key:

- selecting this option to set date

and time

Highlight the item to modify and key: Use the joystick to change the setting to ON and key: to run or: to cancel.

SYSTEM INITIALISE NEAR

DAY TIME

ACT

NEAR

NEAR FAR

selecting this option to set dome motion

OF F

From the main menu, use the joystick to highlight and key:

- when set to ON, the correct password must be entered to access the speed dome setup menus

- allows the current

password to be changed

PASSWORD SETUP NEAR

CHECK PASSWORD (ON/OFF)

SAVE - to save current password.

Passw ord setupPassw ord setup

PA S S W OR D S E TU P

-- - - - -- - - -- - - -- - - - -- - - -- - - -- -

BA C K EX I T

CH E C K P AS S W OR D O F F <E D I T P AS S W OR D >

PA S S W OR D S E TU P

-- - - - -- - - -- - - -- - - - -- - - -- - - -- CH E C K P AS S W OR D O F F <E D I T P AS S W OR D > SA V E C A NC E L

Edit Pa ssword

Pa s s w or d s e tu p

-- - - - -- - - -- - - -- - - - -- - - -- - - -- -

From the password setup menu, use the joystick to highlight and key:

Default password is 11111111

The solid white square shows the current cursor position.

This flashing white square shows the currently selected character.

Move the joystick up / down / left / right to choose the required character and key: to insert it in the password. The solid white square moves to the next cursor position. Repeat until password entry is complete.

If a mistake is made, use the joystick to select the backspace ( ) and key: . The cursor moves back one square.

Select to save the password or to lose changes and key: to exit

EDIT PASSWORD

NEAR

OK CANCEL

NEAR

Remember: When CHECK PASSWORD is set to ON, each time the operator attempts to enter the speed dome setup menu, the above screen will be displayed. The correct password must be entered to continue with menu setup

IN P U T C U RR E N T P AS S W O RD :

11 1 1 1 1 11

AL A R M S ET U P

-- - - - -- - - -- - - -- - - - -- - - -- - - -- AL A R M I N CH A N EL 1 / 8 AL A R M E NA B L E OF F RE L A T E PR E S ET RE L A T E RE L A Y OU T - - -IN P U T S ET U P RE L A Y A CT I V E TI M E SA V E C A NC E L

BA C K EX I T

From the main menu, use the joystick to highlight and key:

- selecting alarm chanel

- this option will enable

alarm function

- selecting related preset

- selecting related relay

out

- set up alarm input

- set relay active time.

Highlight the item to modify and key: Use the joystick to change the setting to ON and key: to run or: to cancel.

ALARM SETUP NEAR

ALARM IN CHANEL

ALARM ENABLE

RELATE PRESET

RELATE RELAY OUT

I INPUT SETUP

RELAY ACTIVE TIME

NEAR

NEAR FAR

Syste m Initialise

SY S T E M IN I T IA L I SE

-- - - - -- - - -- - - -- - - - -- - - -- - - -- CL E A R A LL D A T A

CL R D I S PL A Y S ET CL R C A M ER A S E T CL R M O T IO N S E T

CL R E D I T DA T A RE B O O T CA M E RA RE B O O T SY S T EM

BA C K EX I T

From the main menu, use the joystick to highlight and key:

- this option will erase all

presets, VST functions, patterns and groups

Highlight the item to modify and key: Use the joystick to change the setting to ON and key: to run or: to cancel.

SYSTEM INITIALISE NEAR

CLR EDIT DATA

NEAR

NEAR FAR

CLEAR ALL DATA

CLR DISPLAY SET

CLR CAMERA SET

CLR MOTION SET

- selecting this option will perform a full factory reset on the speed dome. All presets, scan functions, patterns, groups and privacy zones will be erased

- this option will reset the on screen display settings to factory default and erase all privacy zones

- this option will reset the

camera module settings to factory default

- this option will reset the

motion menu settings to factory default

Alarm S etup

Syste m Help

SY S T E M HE L P

-- - - - -- - - -- - - -- - - - -- - - -- - - -- IN C O M M ON U S E , FO L L O W KE Y T O C ON T R OL M E N U : JO G U / D /L / R T O SE L E CT FO C U S N EA R T O C ON F I RM FO C U S F AR T O C A NC E L

BA C K EX I T

From the main menu, use the joystick to highlight and key:

Highlight the item to modify and key: Use the joystick to change the setting to ON and key: to run or: to cancel.

SYSTEM HELP NEAR

NEAR

NEAR FAR

Calli ng the actions

Once t he patter n tours,

and gr oups have b een prog rammed in t he speed do me setu p menu, the y can all be acce ssed dire ctly from t he PTZ cont rol equip ment by usi ng the foll owing seq uences.

scan

func tions

1. To sta rt a p atter n to ur pres s:

Where i s a patte rn t our num be r betwe en 1 & 4

The sel ec ted pat te rn tour w il l run indef in itely u nt il a manu al m oveme nt i s made by t he o perat or o r an alar m in put is recei ve d.

SHOT - 13 X - EN TER

2. To sta rt a s can fun ct ion, pr es s:

Where i s a scan fu nc tion nu mb er betwe en 1 & 8

The sel ec ted sca n fu nctio n wi ll run indef in itely u nt il a manu al m oveme nt i s made by t he o perat or o r an alar m in put is recei ve d.

3. To sta rt a g roup, p re ss:

Where i s a group n um ber bet we en 1 & 8

The sel ec ted gro up w ill run i nd efini te ly until a m an ual mov em ent is ma de b y the opera to r or an ala rm i nput is r ec eived .

SHOT - 14 X - EN TER

SHOT - 15 X - EN TER

Short cut Menu

SHOT - NO .-ENT ER F UNCTI ON

0 (TWIC E) ENTER M AI N MENU

33 RE SE RVE D

34 RESE RV ED

62 RE SE RVE D

63 RESER VED

92 RESER VED

93 RESER VED

94 REMOT E RE SET

95 ENTER M AI N MENU

131-1 34 C AL L PATTER N

141-1 48 C AL L SCA N

151-1 58 C AL L GRO UP

161-1 65 R ESERV ED WORD

170 WDR O FF

171 WDR O N

172 AE AU TO

173 SET SH UTTER S PE ED TO 1 /120 SE C

Heater

Thermostat

Fan

Thermostat

Shield Mount

Tilt Motor

Inner dome cover

Zoom Module

Dome Cover

Pan Motor

Sunshield

Dome Housing

Bracket Mount Base

Bracket Upper Cover

Seal

Housing Upper Cover

Bracket Joint

PCB

Parts and dimensions

138

300

248

230

140

156

325

201

24V AC PS U

485

Cabl e

RS-

Video Ca bl e

Alarm Input

Cable

Powe r Cable

Alar m Sensor

Sire n / Light etc .

powe r source

Alarm Output

Cable

Wiring schematic

Z-36s Z-28s Z-18s

Sensor

1/4-type Exview HAD CCD(PS)

1/4-type Super HAD CCD Ⅱ(IS)

1/4-type Exview HAD

CCD(PS) Horizontal Res 550 TV Lines 550 TV Lines 550 TV Lines Lens 36x 28x 18x Digital Zoom 12x (432x with optical zoom) 12x (336x with optical zoom) 12x (216x with optical zoom)

Horizontal angle of view

57.8°(wide end)

1.7°(tele end) TBD

48.0°(wide end)

2.8°(tele end)

Min. illumination

1.4 lx (F1.6, 50 IRE) 0.1 lx (F1.35, 50IRE)

0.7 lx (F1.4, 50 IRE)

S/N ratio

More than 50 dB

More than 50 dB Day & Night Auto Auto Auto Wide-D On/Off No On/Off Focus Auto/Mauanl Auto/Mauanl Auto/Mauanl

Advanced White Balance

Outdoor Auto mode/ Sodium Vapor Lamp mode

Outdoor Auto mode/

Sodium Vapor Lamp mode

Backlight On/Off On/Off On/Off

Image Stabilization Yes Yes No Stablezoom Yes(up to 40x) Yes(up to 32x) No Digital output Yes Yes Yes

Spherical Privacy Zone Masking Yes Yes Yes

Slow AE response Yes (< 10 min.) Yes (< 10 min

.) Yes (< 10 min.)

Picture effects

E-Flip, Nega Art, B/W, Mirror Image, Color enhancement

E-Flip, Nega Art, B/W, Mirror

Image, Color enhancement Picture freeze Yes Yes Yes

Slow shutter Yes Yes Yes

General

Speeds

Preset

Pattern tours Scan Group Privacy zones Park function Communication Protocols Baud rates Camera ID On Screen Display Environmental rating Alarm I/O Fan/Heater Rated Power Net Weight Operation temperature Humidity

Dimensions

Overall height: 530mm, Overall width: 230mm, Overall depth: 342mm

RS485/RS422( MAX. 255 unit)

IP66

<95%

-30°~50°

8 input/4 output(optional)

Built in

24V AC, 20 watts/24V AC,60 watts (heater on)

Approx 2.5KG

Pan: 360º continuous rotation, Tilt: 90º with auto flip function

Manual: 0.1º - 180º / second, Preset to preset: 400º / second,

Swing: 15º - 30º - 60º / second selectable

1-255

Setup menu, camera position, camera ID, alarm status, preset /Scan / pattern tour status

8 scan

Up to 8, each with up to 20 actions (preset, pattern, scan,nest group)

Up to 127, 15 character title per preset, adjustable dwell time per preset (1 sec ~ 4 min)

Up to 4, maximum 1 minute per tour

Up to 8, user definable

Park to specified preset after a defined period of inactivity (1 min ~ 4 hours)

Pelco-D or Pelco-P optional

2400, 4800, 9600

Provision ISR Ultra-Z-18s, Ultra-Z-36s, Ultra-Z-28s User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual