[Date]
Tal Hanoch
PROVISION-ISR
1
Package Contents:
Item
Qty.
Z-10AHD-1 (IR) PTZ
1
DC12V/3A power supply
1
Wall Screws
4
2
Table of Contents:
1 General Instructions: ................................................................... 3
1.1 Safety Instructions: .......................................................................... 3
1.2 Warnings: ......................................................................................... 3
2 Features: ...................................................................................... 4
2.1 Product Picture: ............................................................................... 4
2.2 Product Features .............................................................................. 4
2.3 Specifications: .................................................................................. 5
3 Installation Site Preparations: ..................................................... 6
3.1 Tool List: ........................................................................................... 6
3.2 Installation Preparation: .................................................................. 6
3.3 DIP Switch Setting: ........................................................................... 6
3.4 Output Mode Setting: ...................................................................... 7
4 Setup of the OSD Menu: .............................................................. 7
4.1 Display Boot-UP Info. ......................................................................... 7
4.2 Enter the OSD Menu: ....................................................................... 8
4.3 SYSTEM Menu: ............................................................................... 10
4.4 LENS ................................................................................................ 13
4.5 Advanced Camera Menu: ............................................................... 15
4.6 PAN/TILT ......................................................................................... 18
4.7 AUTO RUNNING ............................................................................. 19
4.8 IR SET .............................................................................................. 26
APPENDIX I: DIP SWITCH SETTING: ............................................... 27
APPENDIX II Shortcuts Key Chart: ................................................. 32
APPENDIX III Trouble Shooting .................................................... 34
3
1 General Instructions:
1.1 Safety Instructions:
Make sure to read the user manual before using the camera.
Always follow national and local safety codes during the installation.
Only qualified and experienced person can carry the installation and
maintenance for this camera.
Use reliable tools.
Make sure that the environmental conditions meets the installation
requirements for this product.
Please check the space and toughness of the installation surface before
installation. It should be able to bear 4 times the weight of the camera
and its accessories.
1.2 Warnings:
Do not install this speed dome in hazardous places where combustible
or explosive materials are stored or used.
Do not install on platform that suffers from constant vibrations.
Make sure no object or fluid substances get inside the unit.
This speed dome runs on DC 12V, do not connect it to different voltage.
Do not turn power on before installation is complete.
Do not disassemble any part of the camera.
Use soft towel to clean the down the lenses when necessary, do not use
caustic detergent.
To protect the image sensor, avoid facing the camera directly into
strong light.
To prevent damage, do not drop the unit or expose to strong shocks or
vibrations.
Make sure no object is blocking the unit’s full range of motion.
4
2 Features:
2.1 Product Picture:
2.2 Product Features
Adaptive PELCO-P/D protocol.
Adjustable IR illumination.
Memory recall.
Real-Time-Control: call any functions at any time.
Support 128 preset positions.
English OSD menu.
Proportional zoom.
Auto flip function.
Advanced step motor for smoother movement.
Support 4 groups cruise scan, 4 patterns, one scan and 360°continuous
scan and 360° intermittent scan.
IR lights automatically adjust the light intensity according to the zoom
ratio to reduce the dark angle and flashlight effect.
The underpart dome adopts full metal class points bin type design for
fast heat dissipation and anti-mist, non-interference light source images
and long life span IR light.
5
2.3 Specifications:
Power Supply
Input：AC100～240V 50/60Hz
Output：DC12V±5%，3A
Max. Power
Consumption
IR off：~7.2W
IR on：~19.8W
Sync system
Internal Sync
Language
English
Signal Output
AHD/CVBS + PAL/NTSC
Pan Speed
0.08°～240°/S (Max. Preset Speed)
Tilt Speed
0.08°～240°/S (Max. Preset Speed)
Pan Range
0°～360°(Continuous)
Tilt Range
0°～90°（180° auto flip）
Presets
128
Preset Accuracy
<±0.1°
Tour
4 Groups
Pattern
4
Zone
1
Protocol
RS485
Communication
PELCO-D/P auto detected
Baud Rate
2400bps、4800bps、9600bps、19200bps
Address
1-255 (By DIP Switch or Software)
IR Light switch
Superpower LED：Default: Zoom x1~5: open the
near-distance IR lights; Zoom x6~10: keep the near
IR on and opens far-distance IR lights.
Work
Temperature
Indoor：0℃～+50℃；
Outdoor ：-20℃～+50℃ (with heater)
Work Humidity
<90%
6
3 Installation Site Preparations:
3.1 Tool List:
(1) Screws* (2) Monkey wrench
(3) Philips screwdriver (4) Straight Screwdriver
(5) Wire stripper (6) Socket head wrench
(7) Electric drill (8) Hammer
(9) BNC connector (10) BNC Clamp
*Included in the kit
3.2 Installation Preparation:
(1) Check the space and toughness of the site and make sure that the
environmental conditions meet the installation requirements for this product.
(2) The installation surface should be able to bear 4 times the weight of the
PTZ and its accessories.
3.3 DIP Switch Setting:
(1)Default Settings: Pelco P/D (auto-detected), baud rate: 2400, address: 1.
Use Philips screwdriver to remove the DIP switch cover (see location below)
(2)Baud Rate Setup
Decoder Switch: 9~10 (1=ON, 0=OFF)
Switch 9-10 setting
Baud Rate
Max transmission
distance(M)
9
10
0 0 2400BPS
1800
1 0 4800BPS
1200
0 1 9600BPS
800
7
1
1
Auto detected 2400、
4800、9600、
19200BPS
600-1800
(3) When the DIP Switch 9th and 10th are ON, the PTZ can automatically
detected the baud rate 2400, 4800,9600,19200
(4) Hardware Address Setup*: Please refer to Appendix I.
*Please note that the address setting can also be configured via the
software using the camera OSD (Page 11).
3.4 Output Mode Setting:
(1) Default Settings: AHD + PAL/NTSC
This output can be changed via the controller (Even if the user cannot gain a
video output from the unit due to output incompatibility)
(2) Set your controller/DVR PTZ Settings to the Camera’s Default
Communication Settings: Protocol: PELCO-D, address: 1 (Unless user
changed it by the DIP switch configuration), baud rate: 2400.
(3) Call the Preferable Preset that matches your required configuration:
Preset 74 for AHD + PAL
Preset 75 for AHD + NTSC
Preset 76 for CVBS + PAL
Preset 77 for CVBS + NTSC
4 Setup of the OSD Menu:
4.1 Display Boot-UP Info.
Before installation please check the protocol, baud rate, address and RS485
data cable. Default Settings: Protocol: PELCO-D, address: 1, baud rate: 2400.
8
When starting, the PTZ will display the following information:
Once done, the above information will disappear and the user will gain
control over the camera.
4.2 Enter the OSD Menu:
While the camera is in standby condition, call preset 95 (“Call” + 95 + “Enter”)
in order to display the main menu. Use the Up/Down direction to select item
or start the configuration. Use the Right key to confirm and left key for exit
the current setting.
The Main menu as follows:
Level self-check: Success
Vertical self-check: Success
Success
PROTOCOL: PELCO P D
BAUD RATE: 2400BPS
CAMERA ID: 001
CAMERA S/N: 0000000001
MODEL: -----------------
VERSION: V1.02
FAN SPEED: 6000RPM
STARTING… ….
9
SYSTEM
LENS
PAN/TILT
AUTO RUNNING
IR SET
EXIT
10
4.3 SYSTEM Menu:
<Main Menu> <SYSTEM>
System info includes following settings.
< SITE INFO>: In this menu the user can setup the dome’s name, View
the Hardware address, change the camera software address and choose
the leading command (Hardware or Software).
< DISPLAY SETUP >: In this menu the user can choose which details will
display on the camera Screen. The available options are: Site name,
Preset title, Pattern name, Zoom, Orientation, Temperature, Zone name
and RTC time.
<DISPLAY BOOT-UP INFO>: User can view the boot information.
<SET DEFAULT>: All settings will go back to factory default. Preset
positions will be retained.
<SYSTEM REBOOT>: After change dome ID or adjust deviation between
two preset positions, user this to remotely reboot the system.
SITE INFO
DISPLAY SETUP
BOOTUP SCREEN
SET DEFAULT
SYSTEM REBOOT
BACK
EXIT
11
4.3.1 SITE INFO
<Main Menu> <SYSTEM> <SITE INFO >
<DOME ID OPT>: Setting the address method that controls the dome,
user can choose from SOFT (Software – As defined below in the OSD
menu) and HARD (Hardware – As defined by the DIP switch prior to the
installation).
[SOFT]: when choose this, the SOFTWARE ID is effective while the
HARDWARE ID is ineffective.
[HARD]: when choose this, the HARDWARE ID is effective while the
SOFTWARE ID is ineffective.
<SOFTWARE ID>: shows the current software ID, user can modify and
choose address in the range of 001~254
<HARDWARE ID>: shows the current physical ID, it is decided by the DIP
Switch only: user cannot modify via the OSD.
<BROADCAST ID>: shows the current ID, The ID functions the same as
dome’s <SORTWARE/ HARDWARE ID>, The dome works when receives
any of those ID. The dome’s broadcast ID is 255 and cannot be
modified.
DOME ID OPT: HARD
SOFTWARE ID: 001
HARDWARE ID: 001
BROADCAST ID: 255
BACK
EXIT
12
<BACK>: return to upper menu.
<EXIT>: exit the menu
4.3.2 DISPLAY SET UP
< Main Menu><SYSTEM><DISPLAY SETUP>
<PRESET TITLE>：Choose to display preset position or not.
<PATTERN NAME>：Choose to display pattern name or not
<ORIENTATION>：Choose to display the current lens direction or not.
<TEMPRETURE>：Choose to display the current temperature or not.
4.3.3 DISPLAY BOOT-UP INFO
PRESET TITLE: OFF
PATTERN NAME: OFF
ORIENATATION: OFF
TEMPRETURE: OFF
BACK
EXIT
PROTOCOL: PELCO P D
BAUD RATE: 2400BPS
CAMERA ID: 001
CAMERA S/N: 0000000001
MODEL: ----------------VERSION: V3.06*
CALL PRESET 1 TO BACK
13
<Main Menu><SYSTEM><DISPLAY BOOT-UP INFO>
Enter into Boot-up info displays to check current setup, call preset 1 to return
to upper menu
4.3.5 SET DEFAULT
<Main Menu><SYSTEM><SET DEFAULT>
Select <SET DEFAULT> to restore factory default setting.
Please note: there is no confirmation prompt! Once entering the camera
will immediately restore itself.
4.3.6 SYSTEM REBOOT
<Main Menu><SYSTEM><SYSTEM REBOOT>
Select <SYSTEM REBOOT> to reboot the dome.
4.4 LENS
<Main Menu><LENS>
<ZOOM SPEED>: Set the zoom speed level to HIGH or LOW
<DIGITAL ZOOM>: Turn On/Off the Digital Zoom.
<AF/AI SET>: Set up Auto Focus (AF), Auto Iris (AI) or Both
ZOOM SPEED: HIGH
DIGITAL ZOOM: OFF
AF/AI SET: BOTH
AF RESUME TIME: 005
AI RESUME TIME: 005
DAY/NIGHT: IR-CTR
BACK
EXIT
14
<BOTH>: Joystick movement triggers both auto focus and auto iris
<FOCUS>：Joystick movement triggers auto focus only
<IRIS>: Joystick movement triggers auto iris only.
<NONE>: Joystick movement triggers none of the functions.。
<AF RESUME TIME>: This item sets the time to restore auto focus after
focus is manually changed. The default setting is 005, options are:
[OFF] Never restore auto focus after switch to manual.
[001-255]The dome will start auto focus that number of seconds after user
manually adjusts focus.
<AI RESUME TIME>: This item sets the time to restore auto iris after iris
is manually changed. The default setting is 005 seconds, options are:
[OFF]: Never restore auto iris after switch to manual.
[001-255]: The dome will start auto iris that number of seconds after user
manually adjust iris.
<DAY/NIGHT>: Set the dome color/ black & white mode. Color mode is
suitable to work in daytime because it needs higher illumination. Light
sensitivity of black & white mode is much higher. It is suitable to work
at night without illumination but the video is black and white.
There are 4 options:
[AUTO]: The dome will automatically change modes according to the
environment illumination.
[COLOR]: The dome is always in color mode.
[NIGHT]: The dome is always in Black and White mode.
[IR-CTL]: The dome is controlled by the IR lights sensor, when the IR lights
opened, the mode auto change to Black and White.
15
4.5 Advanced Camera Menu:
For advanced Menu, Call preset #69.
PLEASE NOTE: Scrolling and changing values in the advanced menu is done
with different controls:
1) The controller joystick has effect.
2) Scrolling up and down is done by pressing IRIS+/IRIS-
3) Changing Values of the selected feature is done by pressing
ZOOM+/ZOOM-
IMPORTANT!!! Changing any values the advanced menu might result in the
camera malfunctioning
LANG EN
OSD-DISP ON
ADDR-DISP OFF
D&N COL
D&N-LV 30
N&D-LV 12
MIRROR OFF
AGC 15
BRIGHT 15
CONTRAST 15
SHARPNESS 19
SAT 20
WDR OFF
2D-NR 00
3D-NR 02
BLC OFF
16
<LANG>: Language of the menu (Only English Available)
<OSD-DISP >: Do Not Change
<ADDR-DISP>: Do Not Change
<D&N>: Do Not Change
<D&N-LV>: Do Not Change
<N&D-LV>: Do Not Change
<MIRROR>: Turning Mirror effect ON/OFF
<AGC>: changing the value of AGC
<BRIGHT>: Changing the brightness value.
<CONTRAST>: Changing the contrast value.
<SHARPNESS>: Changing the sharpness value.
<SAT>: Changing the saturation value.
<WDR>: Turning Digital WDR effect ON/OFF
<2D-NR>: Adjusting the level of 2D-NR noise reduction
<3D-NR>: Adjusting the level of 3D-NR noise reduction
<BLC>: switching between OFF/ON.
WB AUTO
RGAIN 00
BGAIN 00
DE-FOG 00
OUTPUT AHD
FORMAT 720/25
ZOOM 20
FOCUS AF
Z-SAVE ON
F-RANGE 1.3M
ZDISP-POS RD
RESET
SAVE-EXIT
17
<WB>: White Balance is normally compensated for by the automatic
white balance gain control. In some lighting conditions, user may want
to manually adjust the red and blue settings for optimal viewing. There
are 6 options:
[AUTO]: Auto White Balance (default setting).
[ATW]: Auto track White Balance.
[PUSH]: Once touch White Balance
[OUTDOOR]: Suitable for outdoor use.
[INDOOR]: Suitable for indoor use.
[MANUAL]: Manually set the red and blue values
<BGAIN>: Set the blue value (Only effective if WB is set to Manual)
<RGAIN>: Set the red and value (Only effective if WB is set to Manual)
<DE-FOG>: Change level of defog effect.
<OUTPUT>: Manually set the output between AHD & CVBS
<FORMAT>: Manually set the output between 25&30 (PAL/NTSC)
<ZOOM>: Do Not Change.
<FOCUS>: Do Not Change
<Z-SAVE>: Do Not Change
<F-RANGE >: Do Not Change
<ZDISP-POS >: Set the location of the zoom display (RD – Right Down,
RU – Right Up, LD – Left Down, LU – Left Up)
<RESET >: Reset All settings to factory Default
18
4.6 PAN/TILT
<Main Menu><PAN/TILT>
<AUTO STOP TIME>:
For some particular protocols, the dome will not stop moving even there is
no operation by the controller. This menu sets the time duration before
stopping after which the dome receives last control command.
[Off]: Disable this function
[001~255]: The time (second) that dome will stop moving without receiving
any commands.
<SPEED AMPLIFY>:
Some protocols’ controlling speed is much lower, set <SPEED AMPLIFY> to
accelerate domes movement. Options are as below:
[Off]: Disable this function
[01×~ 32×]: Speed amplify from 01~32x
Notice: The above two functions is not available at present
<PROPORTIONAL P/T>:
The dome moves at a certain speed (degree per second). While zoomed in,
the default movement speed may become too fast. This function decreases
the dome movement speed while zoomed in for easier control on the dome.
AUTO STOP TIME: OFF
SPEED AMPLIFY: OFF
RATIO PAN/TILT: ON
SET NORTH
BACK
EXIT
19
<SET NORTH>:
User can set orientation by using joystick to position north.
When select <SET NORTH>, following menu will pop-up.
Adjust the lens to desired position and call preset 1 to confirm and return.
4.7 AUTO RUNNING
<Main Menu><AUTO RUNNING>
4.7.1 PRESET
<Main Menu><AUTO RUNNING><PRESET>
CALL PRESET 1 TO RETURN
CONFIRM. . . . . .
PRESET
TOUR
PATTERN
360 SCAN
ZONE
PARK TIME: 0S
PARK ACTION: OFF
BACK
EXIT
20
In this function, the values of the pan/tilt positions will be stored in the
desired memory slot so that you will be able to call it when in need. 128
presets can be saved. It could also setup by shortcuts of control system.
<PRESET NUMBER>
Display current preset number, the value ranges from 001to 064 (Except
preset 33 and 34) and 101 to 164
Note: Presets 33/34 has other functions in PELCO protocols, so the user
cannot save any information on it.
<SET CURRENT>
Select this item to set the preset position and zoom. The following menu will
pop-up when < Set Current> is selected.
Move to the desired position and zoom to a suitable level, call preset 1 to
save the current preset and return.
< REMOVE CURRENT>: Delete the preset with the number and title
display above.
4.7.2 TOUR
<Main Menu> <AUTO RUNNING> <TOUR>
PRESET NUMBER: 001
SET CURRNET
REMOVE CURRENT
BACK
EXIT
CALL PRESET 1 TO BACK
CONFIRM … …
21
The dome camera will run repeatedly as the given sequence of presets at
certain dwell time by one command. Max. 4 tours available (27preset/tour).
<TOUR NUMBER>: Set current tour number from 001~004.
<DWELL>: Set the default dwell time from 000~255 seconds for each
preset. User can still set independent dwell time for each preset when
editing the tour.
<EDIT>: Edit presets and corresponding dwell time in a tour as follows.
PRESET–DWELL
000-003 000-003
000-003 000-003
000-003 000-003
000-003 000-003
000-003 000-003
000-003 000-003
000-003 000-003
SAVE AND BACK
CANCEL AND BACK
TOUR NUMBER: 001
DWELL: 003
EDIT
RUN
BACK
EXIT
22
There are three group numbers, the left side is preset number, the right side
is dwell time; tour from left to right, up to down in the order to run preset;
when the preset number is set to < 000>, the current preset is skipped;
<SAVE AND BACK>: Save the tour and back.
<CANCEL AND BACK>: Quit without saving and then exit to the upper
menu.
4.7.3 PATTERN
<Main Menu> <AUTO RUNNING> <PATTERN>
There are max 4 patterns, and the dome camera can record all regular
operation in 3 minutes at least. The command will drive the speed dome runs
as given route repeatedly.
<PATTERN NUMBER>: Set current pattern number from 001～004.
<RECORD>: Edit the current pattern’s running route and record all
operation in 3 minutes at least.
Notice: If any of the time/space is finished, the recording will saved and exit
SET START POINT…
CALL PRE 1 CONFIRM
AND BEGIN RECORDING
CALL PRE 2 CANCEL
PATTERN NUMBER: 001
RECORD
RUN
BACK
EXIT
23
even without calling preset 1.
<RUN>: Run current pattern repeatedly until other command received.
4.7.4 360° SCAN
<Main Menu> <AUTO RUNNING> <360° scan>
<360° SCAN DWELL>:
[0S]: 360 continuous scan
[5S]: 90 intermittent scan, then dwell on 5s, the dome will continuously run
at the given route repeatedly until receiving new command.
[10S]: 90 intermittent scan, then dwell on 10s, the dome will continuously
run at the given route repeatedly until receiving new command.
<PAN SPEED>
High：20/S
Middle：15/S
Low：6/S
Auto：Do as the camera’s proportional P/T speed.
<RUN>
The dome will continuously run at the given route repeatedly until receiving
new command.
4.7.5 ZONE
360° SCAN DWELL: 0S
PAN SPEED: HIGH
RUN
BACK
EXIT
24
<Main Menu> <AUTO RUNNING> <ZONE>
<LEFT LIMIT>: Set the right edge of region <A>
Move the camera left limit position to confirm and return. The position of the
left limit position will now be marked on the menu screen.
<RIGHT LIMIT>: Set the right edge of region (B)
Move the camera right limit position to confirm and return. The position of
the right limit position will now be marked on the menu screen.
<PAN SPEED>
High：20/S
Middle：15/S
Low：6/S
LEFT LIMIT
RIGHT LIMIT
PAN SPEED：LOW
REMOVE CURRENT
RUN
BACK
EXIT
CALL PRESET 1 TO BACK
CONFIRM. . . . . .
CALL PRESET 1 TO BACK
CONFIRM. . . . . .
25
Auto：Do as the camera’s proportional P/T speed.
<REMOVE CURRENT>: Delete current zone
<RUN>: Start current zone scan repeatedly before receiving new
command.
Note:
PTZ default tour scan direction is clockwise starting from the left limit. If the
user finds out the route is wrong, he should call preset 82 preset again and
PTZ will scan in the reverse direction.
4.7.6 <PARK TIME>
The camera will run certain function automatically if the dome is not
receiving any command for the specified time.
0S：PARK TIME OFF
60S：PARK TIME ON, 60 Seconds wait
120S：PARK TIME ON, 120 Seconds wait
4.7.7 <RUNNING TYPE>
Choose the type of action that will take place on activation of Park: users can
choose between: Preset, Tour or Pattern.
Note: Time running available only if <IDLE TIME> and <RUNNING TYPE> are
both ON state.
26
4.8 IR SET
<Main Menu> <IR SET>
<IR MODE >: AUTO/OPEN/CLOSE
<AUTO>: Default. When the detected signal value from the IR sensitive
below the value of IR Start, the IR dome automatically open the IR lights.
<OPEN>: Open the IR lights forcibly (No influence from the detected signal
value).
<CLOSE>: Close the IR lights forcibly (No influence from the detected signal
value).
Notice: The function only effective in <LENS> <DAY/NIGHT> <IR
CHANGE> mode.
<IR ZOOM SET 2>: The Zoom factor that will activate the second set of
IR LEDs
<PRESENT LUX>: Display the current illumination value (Unit: Lux)
(cannot be edited)
<IR START SET>: 006 (Default Open IR light illumination value), Range:
0-8 Unit: Lux
<IR CLOSE SET>: 012 (Close IR light illumination value) Range: 12-20 Unit:
Lux
IR MODE SET: AUTO
IR ZOOM SET 2: 006
PRESENT LUX: 010
IR START SET: 006
IR CLOSE SET: 012
BACK
EXIT
27
APPENDIX I: DIP SWITCH SETTING:
DIP Switch consists of 8 numbers from 1-8, use 8421 binary cod, max 255
address. When the switch is in the “ON” position, the number from 1-8
corresponding to 1, 2, 4, 8, 32, 64, 128. For example, if you set 1, 3, 5, 7
switch to the “ON” position, the corresponding address will be
1+4+16+64=85, please refer to the blow details.
Sheet 1（1=ON, 0=OFF）
DIP switch
Address
K1 ID Switch(number 1-
number 8)
DIP switch
Address
K1 ID Switch(number 1-
number 8)
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1
1 0 0 0 0 0 0 0
2
0 1 0 0 0 0 0 0
3
1 1 0 0 0 0 0 0
4
0 0 1 0 0 0 0 0
5
1 0 1 0 0 0 0 0
6
0 1 1 0 0 0 0 0
7
1 1 1 0 0 0 0 0
8
0 0 0 1 0 0 0 0
9
1 0 0 1 0 0 0 0
10
0 1 0 1 0 0 0 0
11
1 1 0 1 0 0 0 0
12
0 0 1 1 0 0 0 0
13
1 0 1 1 0 0 0 0
14
0 1 1 1 0 0 0 0
15
1 1 1 1 0 0 0 0
16
0 0 0 0 1 0 0 0
17
1 0 0 0 1 0 0 0
18
0 1 0 0 1 0 0 0
19
1 1 0 0 1 0 0 0
20
0 0 1 0 1 0 0 0
21
1 0 1 0 1 0 0 0
22
0 1 1 0 1 0 0 0
23
1 1 1 0 1 0 0 0
24
0 0 0 1 1 0 0 0
25
1 0 0 1 1 0 0 0
26
0 1 0 1 1 0 0 0
27
1 1 0 1 1 0 0 0
28
0 0 1 1 1 0 0 0
29
1 0 1 1 1 0 0 0
30
0 1 1 1 1 0 0 0
31
1 1 1 1 1 0 0 0
32
0 0 0 0 0 1 0 0
33
1 0 0 0 0 1 0 0
34
0 1 0 0 0 1 0 0
28
35
1 1 0 0 0 1 0 0
36
0 0 1 0 0 1 0 0
37
1 0 1 0 0 1 0 0
38
0 1 1 0 0 1 0 0
39
1 1 1 0 0 1 0 0
40
0 0 0 1 0 1 0 0
41
1 0 0 1 0 1 0 0
42
0 1 0 1 0 1 0 0
43
1 1 0 1 0 1 0 0
44
0 0 1 1 0 1 0 0
45
1 0 1 1 0 1 0 0
46
0 1 1 1 0 1 0 0
47
1 1 1 1 0 1 0 0
48
0 0 0 0 1 1 0 0
49
1 0 0 0 1 1 0 0
50
0 1 0 0 1 1 0 0
51
1 1 0 0 1 1 0 0
52
0 0 1 0 1 1 0 0
53
1 0 1 0 1 1 0 0
54
0 1 1 0 1 1 0 0
55
1 1 1 0 1 1 0 0
56
0 0 0 1 1 1 0 0
57
1 0 0 1 1 1 0 0
58
0 1 0 1 1 1 0 0
59
1 1 0 1 1 1 0 0
60
0 0 1 1 1 1 0 0
61
1 0 1 1 1 1 0 0
62
0 1 1 1 1 1 0 0
63
1 1 1 1 1 1 0 0
64
0 0 0 0 0 0 1 0
65
1 0 0 0 0 0 1 0
66
0 1 0 0 0 0 1 0
67
1 1 0 0 0 0 1 0
68
0 0 1 0 0 0 1 0
69
1 0 1 0 0 0 1 0
70
0 1 1 0 0 0 1 0
71
1 1 1 0 0 0 1 0
72
0 0 0 1 0 0 1 0
73
1 0 0 1 0 0 1 0
74
0 1 0 1 0 0 1 0
75
1 1 0 1 0 0 1 0
76
0 0 1 1 0 0 1 0
77
1 0 1 1 0 0 1 0
78
0 1 1 1 0 0 1 0
79
1 1 1 1 0 0 1 0
95
1 1 1 1 1 0 1 0
81
1 0 0 0 1 0 1 0
82
0 1 0 0 1 0 1 0
83
1 1 0 0 1 0 1 0
84
0 0 1 0 1 0 1 0
85
1 0 1 0 1 0 1 0
86
0 1 1 0 1 0 1 0
87
1 1 1 0 1 0 1 0
88
0 0 0 1 1 0 1 0
29
89
1 0 0 1 1 0 1 0
90
0 1 0 1 1 0 1 0
91
0 0 1 1 1 0 1 0
92
0 0 1 1 1 0 1 0
93
1 0 1 1 1 0 1 0
94
0 1 1 1 1 0 1 0
95
1 1 1 1 1 0 1 0
96
0 0 0 0 0 1 1 0
97
1 0 0 0 0 1 1 0
98
0 1 0 0 0 1 1 0
99
1 1 0 0 0 1 1 0
100
0 0 1 0 0 1 1 0
101
1 0 1 0 0 1 1 0
102
0 1 1 0 0 1 1 0
103
1 1 1 0 0 1 1 0
104
0 0 0 1 0 1 1 0
105
1 0 0 1 0 1 1 0
106
0 1 0 1 0 1 1 0
107
1 1 0 1 0 1 1 0
108
0 0 1 1 0 1 1 0
109
1 0 1 1 0 1 1 0
110
0 1 1 1 0 1 1 0
111
1 1 1 1 0 1 1 0
112
0 0 0 0 1 1 1 0
113
1 0 0 0 1 1 1 0
114
0 1 0 0 1 1 1 0
115
1 1 0 0 1 1 1 0
116
0 0 1 0 1 1 1 0
117
1 0 1 0 1 1 1 0
118
0 1 1 0 1 1 1 0
119
1 1 1 0 1 1 1 0
120
0 0 0 1 1 1 1 0
121
1 0 0 1 1 1 1 0
122
0 1 0 1 1 1 1 0
123
1 1 0 1 1 1 1 0
124
0 0 1 1 1 1 1 0
125
1 0 1 1 1 1 1 0
126
0 1 1 1 1 1 1 0
127
1 1 1 1 1 1 1 0
128
0 0 0 0 0 0 0 1
129
1 0 0 0 0 0 0 1
130
0 1 0 0 0 0 0 1
131
1 1 0 0 0 0 0 1
132
0 0 1 0 0 0 0 1
133
1 0 1 0 0 0 0 1
134
0 1 1 0 0 0 0 1
135
1 1 1 0 0 0 0 1
136
0 0 0 1 0 0 0 1
137
1 0 0 1 0 0 0 1
138
0 1 0 1 0 0 0 1
139
1 1 0 1 0 0 0 1
140
0 0 1 1 0 0 0 1
141
1 0 1 1 0 0 0 1
142
0 1 1 1 0 0 0 1
30
143
1 1 1 1 0 0 0 1
144
0 0 0 0 1 0 0 1
145
1 0 0 0 1 0 0 1
146
0 1 0 0 1 0 0 1
147
1 1 0 0 1 0 0 1
148
0 0 1 0 1 0 0 1
149
1 0 1 0 1 0 0 1
150
0 1 1 0 1 0 0 1
151
1 1 1 0 1 0 0 1
152
0 0 0 1 1 0 0 1
153
1 0 0 1 1 0 0 1
154
0 1 0 1 1 0 0 1
155
1 1 0 1 1 0 0 1
156
0 0 1 1 1 0 0 1
157
1 0 1 1 1 0 0 1
158
0 1 1 1 1 0 0 1
159
1 1 1 1 1 0 0 1
160
0 0 0 0 0 1 0 1
161
1 0 0 0 0 1 0 1
162
0 1 0 0 0 1 0 1
163
1 1 0 0 0 1 0 1
164
0 0 1 0 0 1 0 1
165
1 0 1 0 0 1 0 1
166
0 1 1 0 0 1 0 1
167
1 1 1 0 0 1 0 1
168
0 0 0 1 0 1 0 1
169
1 0 0 1 0 1 0 1
170
0 1 0 1 0 1 0 1
171
1 1 0 1 0 1 0 1
172
0 0 1 1 0 1 0 1
173
1 0 1 1 0 1 0 1
174
0 1 1 1 0 1 0 1
175
1 1 1 1 0 1 0 1
176
0 0 0 0 1 1 0 1
177
1 0 0 0 1 1 0 1
178
0 1 0 0 1 1 0 1
179
1 1 0 0 1 1 0 1
180
0 0 1 0 1 1 0 1
181
1 0 1 0 1 1 0 1
182
0 1 1 0 1 1 0 1
183
1 1 1 0 1 1 0 1
184
0 0 0 1 1 1 0 1
185
1 0 0 1 1 1 0 1
186
0 1 0 1 1 1 0 1
187
1 1 0 1 1 1 0 1
188
0 0 1 1 1 1 0 1
189
1 0 1 1 1 1 0 1
190
0 1 1 1 1 1 0 1
191
1 1 1 1 1 1 0 1
192
0 0 0 0 0 0 1 1
193
1 0 0 0 0 0 1 1
194
0 1 0 0 0 0 1 1
195
1 1 0 0 0 0 1 1
196
0 0 1 0 0 0 1 1
31
197
1 0 1 0 0 0 1 1
198
0 1 1 0 0 0 1 1
199
1 1 1 0 0 0 1 1
200
0 0 0 1 0 0 1 1
201
1 0 0 1 0 0 1 1
202
0 1 0 1 0 0 1 1
203
1 1 0 1 0 0 1 1
204
0 0 1 1 0 0 1 1
205
1 0 1 1 0 0 1 1
206
0 1 1 1 0 0 1 1
207
1 1 1 1 0 0 1 1
208
0 0 0 0 1 0 1 1
209
1 0 0 0 1 0 1 1
210
0 1 0 0 1 0 1 1
211
1 1 0 0 1 0 1 1
212
0 0 1 0 1 0 1 1
213
1 0 1 0 1 0 1 1
214
0 1 1 0 1 0 1 1
215
1 1 1 0 1 0 1 1
216
0 0 0 1 1 0 1 1
217
1 0 0 1 1 0 1 1
218
0 1 0 1 1 0 1 1
219
1 1 0 1 1 0 1 1
220
0 0 1 1 1 0 1 1
221
1 0 1 1 1 0 1 1
222
0 1 1 1 1 0 1 1
223
1 1 1 1 1 0 1 1
224
0 0 0 0 0 1 1 1
225
1 0 0 0 0 1 1 1
226
0 1 0 0 0 1 1 1
227
1 1 0 0 0 1 1 1
228
0 0 1 0 0 1 1 1
229
1 0 1 0 0 1 1 1
230
0 1 1 0 0 1 1 1
231
1 1 1 0 0 1 1 1
232
0 0 0 1 0 1 1 1
233
1 0 0 1 0 1 1 1
234
0 1 0 1 0 1 1 1
235
1 1 0 1 0 1 1 1
236
0 0 1 1 0 1 1 1
237
1 0 1 1 0 1 1 1
238
0 1 1 1 0 1 1 1
239 240
0 0 0 0 1 1 1 1
32
APPENDIX II Shortcuts Key Chart:
*Relevant for all models produced in 2016 and later. For older
production please contact Provision-ISR’s technical support
Shortcut Key
Function (Set Preset)
Set #84preset
Proportional P/T OFF
Set #85preset
Set Output: AHD PAL
Set #86preset
Set Output: AHD NTSC
Set #87preset
Set Output: CVBS PAL
Set #88 preset
Set Output: CVBS NTSC
Set # 89preset
Delete all presets
Set #90 preset
Set left limit Position
Set #91preset
Set right limit Position
Set #92 preset
Delete left/right limit
Set #93preset
Dome restart
Set #94 preset
Restore Factory Setting
Set #95preset
Open main menu
Set #96 preset
0S Park time ON
Set #97 preset
60S Park time ON
Set #98preset
120S Park time ON
Set #99 preset
360° scan and tour scan speed is automatic
Set #100 preset
360° scan and tour scan speed is high, 20°/sec
Set #101preset
360° scan and tour scan speed is middle, 15°/sec
Set #102preset
360° scan and tour scan speed is low, 6°/sec
Set #103 preset
Record Pattern scan 1
Set #104 preset
Record Pattern scan 2
Set #105 preset
Record Pattern scan 3
33
Set #106 preset
Record Pattern scan 4
Set #107 preset
Set cruise 1
Set #108 preset
Set cruise 2
Set #109 preset
Set cruise 3
Set #110 preset
Set cruise 4
Set #111 preset
Set color-to-black function
Set #112 preset
Set 360°scan, the preset-dwell: 0S
Set #113preset
Set 360°scan, the preset-dwell: 5S
Set #114preset
Set 360°scan, the preset-dwell: 10S
Shortcut key
Function (Call preset)
Call #69 preset
Open Advanced Settings menu
Call #70 preset
Preset Error Correction
Call #71 preset
Proportional P/T ON
Call #72 preset
Start Cruise scan and switch the cruise scan direction
Call #73 preset
Start Pattern 1
Call #74 preset
Start Pattern 2
Call #75 preset
Start Pattern 3
Call #76 preset
Start Pattern 4
Call #77 preset
Call cruise 1 (default number 1~16 preset)
Call #78 preset
Call cruise 2 (default number 17~32 preset)
Call #79 preset
Call cruise 3 (default number 35~48 preset)
Call #80preset
Call cruise 4 (default number 49~64 preset)
Call #81 preset
Camera IR-CUT switch
Call #82 preset
Call all valid presets cruise
Call #83 preset
Call 360°scan
Call #95preset
Open main menu (Same response as “Set”)
34
APPENDIX III Trouble Shooting
Troubles
Reason
Solution
No action when power on
1. The power supply is not
connected correctly.
2. The fuse is broken.
1. Correct the connection.
2. Check the power supply LED
power indicator.
3. Replace the fuse.
Self-testing and image are
normal but the dome is out
of control
1. The dome DIP switch
setting is incorrect.
2. RS485 cable is
disconnected or reversed.
3. Control device is not
properly configured.
1. Confirm DIP settings on camera
power up screen.
2. Reset the DIP Switch according
to the DIP switch chart.
3. Check the wiring.
4. Check the control device settings
Some function is out of
control
1. RS485 communication
signal is not balance.
2. Control protocol is not
compatible.
1. Connect 120Ω resistor to the
RS485 line.
2. Change protocol type.
Unclear image
1. Focus is in manual state.
2. Digital Zoom is on and in
full ratio (If applicable)
3. Dome cover is dirty.
1. Reset the focus mode to Auto.
2. Cancel/reduce digital zoom.
3. Clean the dome cover.
No night vision
1. Camera is in Color mode.
2. backlight on the top or
back of the dome camera
1. Reset the day/night function to
Auto.
2. Remove the direct light source.
35
Loading...