Proto J138WA, J150WA User Manual
J138WA and J150WA
J138WA
J150WA
an
d these safety
Keep these
have a
ny
or
.
1
3
perat
o
n
Operation and Maintenance Manual
3/8" J138WA
"
1/2" J150WA
"
To reduce the risk of injury, read and understand these safety
warnings and instructions before using the tool.
instructions with the tool for future reference. If you have any
questions, contact your PROTO® representative or distributor.
3/8" Drive Right Angle Impact
1/2" Drive Right Angle Impact
WARNING
Keep these
TABLE OF CONTENTS
Introduction 2
Safety Instructions 3
Specifications 4
Getting Started 5
Tool Components 6
Contact Information 8
INTRODUCTION
The PROTO® J138WA and J150WA are precision-built tools, designed for professionals for high torque assembly and disassembly of
threaded fasteners. These tools will deliver efficient, dependable service when used correctly and with care. As with any fine power
tool, for best performance the manufacturer’s instructions must be followed. Please study this manual before operating the tool and
understand the safety warnings and instructions. The instructions on installation, operation and maintenance should be read carefully,
and the manuals kept for reference. NOTE: Additional safety measures may be required because of your particular application of the tool.
Contact your PROTO® Distributor with any questions concerning the tool and its use.
PROTO INDUSTRIAL TOOLS
2195 East View Parkway
Suite 103
Conyers, Georgia 30013
Phone: +1 800-800-TOOL
Fax: +1 770-648-9108
www.protoindustrial.com
®
WARRANTY
We warrant that this tool shall be free from manufacturing defects for a period of ONE YEAR from the original purchase date. Our
obligation to the original purchaser shall be limited to repairing or replacing, at our expense (not including shipping charges) a defective
tool if returned by the original purchaser within two years from the date of purchase, all incoming shipping charges prepaid. THIS
WARRANTY DOES NOT COVER DEFECTS OR DAMAGES TO THE TOOL (i) after the warranty period expires; (ii) resulting from misuse or
abnormal operation; (iii) resulting from a failure to properly lubricate, maintain or operate the tool; or (iv) resulting from any repair or
maintenance services performed by any party other than PROTO® at all DeWALT Service Centers or a person authorized by PROTO® to
provide repair and maintenance services for this tool.
2
WARNING
IMPORTANT SAFETY INFORMATION ENCLOSED.
READ THIS MANUAL BEFORE OPERATING THE MACHINE.
FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN INJURY.
Do not use damaged, frayed or deteriorated air
hoses and fittings.
Air powered tools can vibrate in use. Vibration,
repetitive motions or uncomfortable positions may
be harmful to your hands and arms. Stop using any
tool if discomfort, tingling feeling or pain occurs.
Seek medical advice before resuming use.
Do not carry the tool by the hose.
Keep body stance balanced and firm. Do not overreach when operating this tool.
6.2 bars
(90 psig/620 kPa)
Always wear hearing protection when operating
this tool.
Always turn off the air supply and disconnect
the air supply hose before installing, removing
or adjusting any accessory on this tool, or before
performing any maintenance on this tool.
Always wear eye protection when operating or
performing maintenance on this tool.
Operate at 90 psig (6.2 bar / 620 kPa) Maximum
air pressure.
GENERAL SAFETY INSTRUCTIONS
WARNING
Always wear ANSI Z87.1 eye protection when operating or performing maintenance on this tool. Everyday
eye glasses are not safety glasses.
Always wear hearing protection when operating this tool.
Keep hands, loose clothing and long hair away from rotating end of tool.
Anticipate and be alert for sudden changes in motion during start up and operation of any power tool.
Keep body stance balanced and firm. Do not overreach when operating this tool.
Do not operate this tool for long periods of time. Vibration caused by tool action may be harmful to your
hands and arms. Stop using any tool if discomfort, tingling feeling or pain occurs. Seek medical advice
before resuming use.
Use rated accessories recommended by PROTO® only. Inspect accessories before use. Do not use cracked
or damaged accessories.
Do not operate this tool in the presence of flammable liquids, gasses, dust, or explosive atmospheres
This tool is not insulated against electric shock.
For safety, top performance, and maximum durability of parts, operate this tool at 90 psig.
(6.2 bar / 620 kPa) maximum air pressure at the inlet with 3/8’’ (10mm) inside diameter air supply hose.
Always turn off the air supply and disconnect the air supply hose before installing, removing or adjusting
any accessory on this tool, or before performing any maintenance on this tool.
Do not use damaged, frayed or deteriorated air hoses and fittings.
Do not lubricate tools with flammable or volatile liquids such as kerosene, diesel or jet fuel.
Do not remove any labels. Replace any damaged label.
3
Loading...