Protex PRX-MG04 Series, PRX-MG08 Series, PRX-MG16 Series User Manual

Download

www.protexitalia.it

Standalone DVR User’s Manual

PRX-MG04x

PRX-MG08x

PRX-MG16x

Table of Contents

1111 FEATURES AND SPECIFI

FEATURES AND SPECIFIFEATURES AND SPECIFI

FEATURES AND SPECIFICATIONS

CATIONSCATIONS

CATIONS................................................................10

1.1

1.11.1

1.1

Features

FeaturesFeatures

Features ................................................................................................................................................10

1.2

1.21.2

1.2

Specifications

SpecificationsSpecifications

Specifications .......................................................................................................................................10

2222 OVERVIEW AND CONTROL

OVERVIEW AND CONTROLOVERVIEW AND CONTROL

OVERVIEW AND CONTROLS

S .........................................................................14

2.1

2.12.1

2.1

Front Panel

Front PanelFront Panel

Front Panel ...........................................................................................................................................14

2.2

2.22.2

2.2

Rear Panel

Rear PanelRear Panel

Rear Panel............................................................................................................................................16

2.2.1 Overview ..........................................................................................................................................16

2.2.2 Connection Sample ........................................................................................................................16

2.3

2.32.3

2.3

Remote Control

Remote ControlRemote Control

Remote Control ....................................................................................................................................17

2.4

2.42.4

2.4

Mouse Control

Mouse ControlMouse Control

Mouse Control......................................................................................................................................18

2.5

2.52.5

2.5

Virtual Keyboard & Front Panel

Virtual Keyboard & Front PanelVirtual Keyboard & Front Panel

Virtual Keyboard & Front Panel.........................................................................................................20

2.5.1 Virtual Keyboard..............................................................................................................................20

2.5.2 Front Panel ......................................................................................................................................20

3333 INSTALLATION AND CON

INSTALLATION AND CONINSTALLATION AND CON

INSTALLATION AND CONNECTIONS

NECTIONSNECTIONS

NECTIONS............................................................. 21

3.1

3.13.1

3.1

Check Unpacked DVR

Check Unpacked DVRCheck Unpacked DVR

Check Unpacked DVR ........................................................................................................................21

3.2

3.23.2

3.2

HDD Installation

HDD InstallationHDD Installation

HDD Installation ...................................................................................................................................21

3.2.1 Choose HDDs..................................................................................................................................21

3.2.2 Calculate HDD Size........................................................................................................................21

3.2.3 HDD Installation ..............................................................................................................................21

3.3

3.33.3

3.3

CD/DVD Burner Installation

CD/DVD Burner InstallationCD/DVD Burner Installation

CD/DVD Burner Installation ...............................................................................................................22

3.4

3.43.4

3.4

Desktop and Rack Mounting

Desktop and Rack MountingDesktop and Rack Mounting

Desktop and Rack Mounting..............................................................................................................23

3.4.1 Desktop Mounting........................................................................................................................... 23

3.4.2 Rack Mounting ................................................................................................................................23

3.5

3.53.5

3.5

Connecting Power Supply

Connecting Power SupplyConnecting Power Supply

Connecting Power Supply ..................................................................................................................23

3.6

3.63.6

3.6

Connecting Video Input and Output Devices

Connecting Video Input and Output DevicesConnecting Video Input and Output Devices

Connecting Video Input and Output Devices ..................................................................................23

3.6.1 Connecting Video Input..................................................................................................................23

3.6.2 Connecting Video Output............................................................................................................... 24

3.7

3.73.7

3.7

Connecting Audio Input & Output, Bidirectional Audio, Looping Video, Matrix

Connecting Audio Input & Output, Bidirectional Audio, Looping Video, MatrixConnecting Audio Input & Output, Bidirectional Audio, Looping Video, Matrix

Connecting Audio Input & Output, Bidirectional Audio, Looping Video, Matrix..........................24

3.7.1 Audio Input/One Audio Output......................................................................................................25

3.7.2 Looping video..................................................................................................................................25

3.7.3 Matrix Video Output........................................................................................................................26

3.7.4 Alarm Input and Relay Output....................................................................................................... 26

3.7.5 Alarm Input.......................................................................................................................................26

3.7.6 Alarm Output....................................................................................................................................27

3.7.7 Alarm Input and Output Details ........................................................................................................27

3.7.8 Relay Output Description...............................................................................................................28

3.8

3.83.8

3.8

RS232

RS232RS232

RS232....................................................................................................................................................29

3.9

3.93.9

3.9

RS485

RS485RS485

RS485....................................................................................................................................................30

3.10

3.103.10

3.10 Other Interfaces

Other InterfacesOther Interfaces

Other Interfaces ...................................................................................................................................30

4444 OVERVIEW OF NAVIGATI

OVERVIEW OF NAVIGATIOVERVIEW OF NAVIGATI

OVERVIEW OF NAVIGATION AND CONTROLS

ON AND CONTROLSON AND CONTROLS

ON AND CONTROLS ............................................ 31

4.1

4.14.1

4.1

Login, Logout & Main Menu ...............................................................................................................31

4.1.1 Login................................................................................................................................................. 31

4.1.2 Main Menu .......................................................................................................................................31

4.1.3 Logout............................................................................................................................................... 32

4.1.4 Auto Resume after Power Failure ................................................................................................32

4.1.5 Replace Button Battery..................................................................................................................32

4.2

4.24.2

4.2

Recording Operation

Recording OperationRecording Operation

Recording Operation ...........................................................................................................................32

4.2.1 Live Viewing.....................................................................................................................................33

4.2.2 Manual record..................................................................................................................................33

4.3

4.34.3

4.3

Search & Playback

Search & PlaybackSearch & Playback

Search & Playback ..............................................................................................................................35

4.3.1 Search Menu ...................................................................................................................................35

4.3.2 Basic Operation...............................................................................................................................36

4.3.3 Calendar........................................................................................................................................... 38

4.4

4.44.4

4.4

Record Setup (Schedule)

Record Setup (Schedule)Record Setup (Schedule)

Record Setup (Schedule) ...................................................................................................................38

4.4.1 Schedule Menu ....................................................................................................................................38

4.4.2 Basic Operation....................................................................................................................................38

4.5

4.54.5

4.5

Detect

DetectDetect

Detect ....................................................................................................................................................40

4.5.1 Go to Detect Menu...............................................................................................................................40

4.5.2 Motion Detect........................................................................................................................................40

4.5.3 Video Loss.............................................................................................................................................43

4.5.4 Camera Masking..................................................................................................................................44

4.6

4.64.6

4.6

Alarm Setup and Alarm Activation

Alarm Setup and Alarm ActivationAlarm Setup and Alarm Activation

Alarm Setup and Alarm Activation ....................................................................................................45

4.6.1 Go to alarm setup interface...........................................................................................................45

4.6.2 Alarm setup......................................................................................................................................45

4.7

4.74.7

4.7

Backup

BackupBackup

Backup ..................................................................................................................................................47

4.7.1 Detect Device.......................................................................................................................................47

4.7.1 Backup..............................................................................................................................................48

4.8

4.84.8

4.8

PTZ Control and Color Setup

PTZ Control and Color SetupPTZ Control and Color Setup

PTZ Control and Color Setup ............................................................................................................49

4.8.1 Cable Connection ................................................................................................................................49

4.8.2 PTZ Setup.............................................................................................................................................49

4.8.3 3D Intelligent Positioning Key............................................................................................................51

4.9

4.94.9

4.9

Preset/ Patrol/

Preset/ Patrol/Preset/ Patrol/

Preset/ Patrol/Pattern/Scan

Pattern/ScanPattern/Scan

Pattern/Scan................................................................................................................51

4.9.1Preset Setup .........................................................................................................................................52

4.9.2 Activate Preset.....................................................................................................................................53

4.9.3 Patrol setup (Tour Setup)...................................................................................................................53

4.9.4 Activate Patrol (tour)...........................................................................................................................53

4.9.5 Pattern Setup.......................................................................................................................................53

4.9.6 Activate Pattern Function................................................................................................................... 54

4.9.7 Auto Scan Setup .................................................................................................................................54

4.9.8 Activate Auto Scan..............................................................................................................................54

4.10

4.104.10

4.10 Flip

FlipFlip

Flip .........................................................................................................................................................54

5555 UNDERSTANDING OF MEN

UNDERSTANDING OF MENUNDERSTANDING OF MEN

UNDERSTANDING OF MENU OPERATIONS AND CON

U OPERATIONS AND CONU OPERATIONS AND CON

U OPERATIONS AND CONTROLS

TROLSTROLS

TROLS ................... 55

5.1

5.15.1

5.1

Menu Tree

Menu TreeMenu Tree

Menu Tree ............................................................................................................................................55

5.2

5.25.2

5.2

Main Menu

Main MenuMain Menu

Main Menu ............................................................................................................................................55

5.3

5.35.3

5.3

Setting

SettingSetting

Setting ...................................................................................................................................................56

5.3.1 General............................................................................................................................................. 56

5.3.2 Encode .............................................................................................................................................58

5.3.3 Schedule ..........................................................................................................................................60

5.3.4 RS232............................................................................................................................................... 60

5.3.5 Network ............................................................................................................................................61

5.3.6 Alarm.................................................................................................................................................68

5.3.7 Detect ...............................................................................................................................................68

5.3.8 Pan/Tilt/Zoom..................................................................................................................................68

5.3.9 Display..............................................................................................................................................69

5.3.10 Default..........................................................................................................................................71

5.4

5.45.4

5.4

SearchSearch

Search ...................................................................................................................................................72

5.5

5.55.5

5.5

Advanced

AdvancedAdvanced

Advanced ..............................................................................................................................................72

5.5.1 HDD Management..........................................................................................................................72

5.5.2 Abnormity.........................................................................................................................................73

5.5.3 Alarm Output....................................................................................................................................74

5.5.4 Manual Record................................................................................................................................74

5.5.5 Account.............................................................................................................................................74

5.5.6 Auto Maintain...................................................................................................................................75

5.5.7 TV Adjust..........................................................................................................................................76

5.5.8 Video Matrix (For MGxxH Series only)........................................................................................76

5.6

5.65.6

5.6

Information

InformationInformation

Information............................................................................................................................................80

5.6.1 HDD Information .............................................................................................................................81

5.6.2 BPS...................................................................................................................................................81

5.6.3 Log....................................................................................................................................................82

5.6.4 Version .............................................................................................................................................82

5.6.5 Online Users....................................................................................................................................83

5.7

5.75.7

5.7

Exit

ExitExit

Exit .........................................................................................................................................................83

6666 ABOUT AUXILIARY MENU

ABOUT AUXILIARY MENUABOUT AUXILIARY MENU

ABOUT AUXILIARY MENU ..............................................................................85

6666.1

.1.1

Go to Pan/Tilt/Zoom Menu

Go to Pan/Tilt/Zoom MenuGo to Pan/Tilt/Zoom Menu

Go to Pan/Tilt/Zoom Menu .................................................................................................................85

6.1.1 3D Intelligent Positioning Key .......................................................................................................86

6.2

6.26.2

6.2

Preset /Patrol / Pattern /Border Function

Preset /Patrol / Pattern /Border FunctionPreset /Patrol / Pattern /Border Function

Preset /Patrol / Pattern /Border Function.......................................................................................86

6.2.1 Preset Setup....................................................................................................................................87

6.2.2 Activate Preset................................................................................................................................87

6.2.3 Patrol Setup.....................................................................................................................................87

6.2.4 Activate Patrol .................................................................................................................................88

6.2.5 Pattern Setup...................................................................................................................................88

6.2.6 Activate Pattern Function............................................................................................................... 88

6.2.7 Border Setup....................................................................................................................................88

6.2.8 Activate Border Function ...............................................................................................................88

6.2.9 Flip.....................................................................................................................................................88

7777 WEB CLIENT OPERATION

WEB CLIENT OPERATIONWEB CLIENT OPERATION

WEB CLIENT OPERATION ..............................................................................90

7.1

7.17.1

7.1

Network Connection

Network ConnectionNetwork Connection

Network Connection ............................................................................................................................90

7.2

7.27.2

7.2

LoginLogin

Login ......................................................................................................................................................90

7.2.1 Real-time Monitor............................................................................................................................93

7.2.2 PTZ ...................................................................................................................................................94

7.2.3 Color .................................................................................................................................................97

7.2.4 Picture Path and Record Path ......................................................................................................97

7.2.5 Menu Interface Switch....................................................................................................................98

7.3

7.37.3

7.3

Configure

ConfigureConfigure

Configure ..............................................................................................................................................99

7.3.1 System Information.........................................................................................................................99

7.3.2 Setting.............................................................................................................................................102

7.4

7.47.4

7.4

SearchSearch

Search .................................................................................................................................................121

7.4.1 Download.......................................................................................................................................122

7.5

7.57.5

7.5

Alarm

AlarmAlarm

Alarm ...................................................................................................................................................123

7.6

7.67.6

7.6

About

AboutAbout

About ...................................................................................................................................................124

7.7

7.77.7

7.7

Log out

Log outLog out

Log out ................................................................................................................................................124

7.8

7.87.8

7.8

UnUn

Un----install Web Control

install Web Controlinstall Web Control

install Web Control ......................................................................................................................124

8888 ENTERPRISE PROFESSIO

ENTERPRISE PROFESSIOENTERPRISE PROFESSIO

ENTERPRISE PROFESSIONAL SURVEILLANCE SYS

NAL SURVEILLANCE SYSNAL SURVEILLANCE SYS

NAL SURVEILLANCE SYSTEM

TEMTEM

TEM ........................125

8.1

8.18.1

8.1

Log inLog in

Log in...................................................................................................................................................125

8.2

8.28.2

8.2

Enable Monitor

Enable MonitorEnable Monitor

Enable Monitor ...................................................................................................................................126

8.3

8.38.3

8.3

Add New Device

Add New DeviceAdd New Device

Add New Device ................................................................................................................................127

9999 RS232 OPERATION

RS232 OPERATIONRS232 OPERATION

RS232 OPERATION ....................................................................................... 129

9.1

9.19.1

9.1

Network Connection

Network ConnectionNetwork Connection

Network Connection ..........................................................................................................................129

9.2

9.29.2

9.2

Keyboard

KeyboardKeyboard

Keyboard.............................................................................................................................................129

1010

10 FAQ

FAQFAQ

FAQ.................................................................................................................130

APPENDIX A

APPENDIX AAPPENDIX A

APPENDIX A HDD CAPACITY CALCULA

HDD CAPACITY CALCULAHDD CAPACITY CALCULA

HDD CAPACITY CALCULATION

TIONTION

TION .................................................135

APPENDIX B

APPENDIX BAPPENDIX B

APPENDIX B COMPATIBLE USB DRIVE

COMPATIBLE USB DRIVECOMPATIBLE USB DRIVE

COMPATIBLE USB DRIVE LIST

LIST LIST

LIST .................................................. 136

APPENDIX C

APPENDIX CAPPENDIX C

APPENDIX C COMPATIBLE CD/DVD BU

COMPATIBLE CD/DVD BUCOMPATIBLE CD/DVD BU

COMPATIBLE CD/DVD BURNER LIST

RNER LISTRNER LIST

RNER LIST........................................137

APAP

APPENDIX D COMPATIBLE

PENDIX D COMPATIBLE PENDIX D COMPATIBLE

PENDIX D COMPATIBLE SATA HDD LIST

SATA HDD LISTSATA HDD LIST

SATA HDD LIST......................................................138

Welcome

Thank you for purchasing our DVR! This operating manual is designed to be a reference tool for the installation and operation of your system. Here you can find information about this series DVR features and functions, as well as a detailed menu tree. Before installation and operation please read the following safeguards and warnings carefully!

Important Safeguards and Warnings

1．．．．Electrical safety

All installation and operation here should conform to local electrical safety codes. We assume no liability or responsibility for all the fires or electrical shock caused by improper handling or installation.

2．．．．Transportation security

Heavy stress, violent vibration or water splash are not allowed during transportation, storage and installation.

3．．．．Installation

Keep upwards. Handle with care. Do not apply power to the DVR before completing installation. Do not place objects on the DVR

4．．．．Qualified engineers needed

All the examination and repair work should be done by the qualified service engineers. We are not liable for any problems caused by unauthorized modifications or attempted repair.

5．．．．Environment

The DVR should be installed in a cool, dry place away from direct sunlight, inflammable, explosive substances and etc.

6. Accessories

Be sure to use all the accessories recommended by manufacturer. Before installation, please open the package and check all the components listed below are included:

 One power cable  One Ethernet cable  Four HDD cables  Alarm & relay terminal blocks  Extensional cable(for audio, loop & matrix)  One remote control(including the battery)  One USB mouse  One CD(including DVR manual, client & small tools)  Warranty card  A package of installation fittings

Contact your local retailer ASAP if something is missing in your package.

Note: Any changes of this manual made to the actual product are subject to no further notification.

FFF

FEATURES AND SPECIFICATIONS

EATURES AND SPECIFICATIONSEATURES AND SPECIFICATIONS

EATURES AND SPECIFICATIONS

1.1

1.11.1

1.1 Feature

FeatureFeature

Featuressss

This series DVR has the following features:

 H.264 compression algorithm ideal for standalone DVR  Real-time live display up to 16 cameras, 400/480 fps recording for CIF, 2CIF&

200/240 fps recording for 4CIF

 Pentaplex function: live, recording, playback, backup & remote access  Dual encoding streams support, flexible for network transmission  Intelligent search and playback support, you can play back the video only motion

detection occurs in the area you selected.

 8 HDDs supported & CD-RW/DVD-RW supported  Multiple control methods: front panel, IR remote control, keyboard, USB mouse

and network keyboard.

 Smart video detection: motion detection, camera masking, video loss.  Smart camera settings: privacy masking, camera lock, color setting, and title

display

 Pan Tilt Zoom and Speed Dome Control: more than 60 protocols supported,

preset, scan, auto pan, auto tour, pattern, auxiliary function supported. And with our Speed Dome, 3D intelligent positioning function supported.

 Easy backup methods: USB devices, CD-RW/DVD-RW & network download  Alarm triggering screen tips, buzzer, PTZ preset, e-mail, FTP upload.  Smart HDDs Management: non-working HDD hibernation, HDD faulty alarm,

Raid function.

 Powerful network software: built-in web server, EPSS. Networking access for

remote live viewing, recording, playback, setting, system status, event log, e-mail & ftp function.



1.2

1.21.2

1.2 Specification

SpecificationSpecification

Specificationssss

Model

PRX-MG04H/MG08H/MG16H 4/8/16 channel loop matrix and audio/video model PRX-MG16J 16 channel loop and matrix combined model

System

Main Processor High performance embedded microprocessor Operating System Embedded LINUX System Resources Pentaplex function: live, recording, playback, backup &

remote access User Interface GUI, on-screen menu tips. Control Device Front panel, USB mouse, keyboard, IR remote

control, network keyboard,. Input Method Numeral/Character/Denotation System Status HDD status, data stream statistics, log record, bios

version, on-line user and etc.

Video

Video Input 4/8/16 Channel, BNC, 1.0Vp-p, 75Ω, looping(optional), Video Output 2-channel TV output BNC, 1.0Vp- p, 75Ω,1 VGA output,

matrix output(optional) Video Standards PAL（625Line，50f/s），NTSC（525Line，60f/s）

Video Compression H.264 Video Resolution Format NTSC PAL D1(4CIF) 704 * 480 704 * 576

2CIF 704 *240 704 * 288 CIF 352* 240 352*288 QCIF 176*120 176*144

Video Recording D1/2CIF/CIF/QCIF: PAL 1f/s-25f/s NTSC 1f/s-30f/s； Video Display Split Full and multiple screen display, 1 / 4 / 8 / 9 / 16

Tour Display Support Image Quality 1~6 level (level 6 is the best) Privacy Masking Self-defined four-sided zone for privacy masking for each

camera Camera Lock Camera locked for users Camera Adjustment Adjust color according to different time periods Video Information Camera title, time, video loss, camera lock, motion

detection, recording TV Output Adjustment Adjust TV output color & display zone

Audio

Audio Input 4/8/16 channel, BNC, 200-2800mV, 30KΩ bidirectional Audio Input 1-channel, RCA, 200-2800mV, 30KΩ Audio Output 1-channel, RCA, 200-3000mv, 5KΩ Audio Compression ADPCM

Video Detection & Alarm

Motion Detection Zones: PAL 396 (22*18)/NTSC 330(22*15) detection

zones Sensitivity: 1~6 (level 6 is highest) Trigger recording, PTZ movement, tour, alarm, e-mail &

FTP Video Loss Trigger recording, PTZ movement, tour, alarm, e-mail &

FTP Camera masking Trigger recording, PTZ movement, tour, alarm, e-mail

& FTP Alarm Input 4/8/16 channel, programmable, ground, manual

open/closed Trigger recording, PTZ movement, tour, alarm, e-mail &

FTP Relay output 6-channel, 30VDC, 1A, NO/NC, form-C,

Hard Disk

Hard Disk 8 SATA ports, 8 HDDs supported. Space Occupation Audio ：14.4MB/H Video ：56～700MB/H

HDD Management Hard disk hibernation technology, HDD faulty alarm &

Raid (Redundancy)

Record, Playback & Backup

Recording Mode Manual, continuous, video detection (including motion

detection, camera masking, video loss), Alarm Recording Priority Manual >Alarm >Video Detection >Continuous. Recording Interval 1 to 120 minutes (default: 60 minutes) Overwrite Mode Support Raid Function Support Search Mode Time/Date, Alarm, Motion Detection & exact search

(accurate to second) Playback 2-channel playback simultaneously, Play, pause, stop,

rewind, fast play, slow play, next file, previous file,

next camera, previous camera, full screen, repeat,

shuffle, backup selection. Digital Zoom Selected zone can zoom into full screen during

playback Backup Mode Flash stick/ USB HDD/ USB CD-RW/DVD-RW/ built-

in SATA Burner/ network download

Network

Interface RJ-45 Port (10/100M) Network Functions TCP/IP, DHCP, DDNS, PPPoE, E-mail, FTP Remote operation Monitor, PTZ control, playback, system setting, file

download, log information

Auxiliary Interface

USB Interface 2 USB 2.0 ports, 1 for mouse control, 1 for backup. RS232 Keyboard, PC communication RS485 PTZ control

Environmental

Power Supply 220V 50Hz / 110V 60Hz Power Consumption 25W/30W/40W

Working Temperature 0℃~＋55℃ Power Consumption 25W/30W/40W

Working Humidity 10%~90% Atmosphere Pressure 86kpa~106kpa Dimension 2U, 440mmx460mmx89mm (W*D*H) Weight 7.0KG Mounting Desktop or rack

Note: Comparisons

Model Audio Input Loop Output Matrix Output Bidirectional Talk Input PRX-MG04H 4 channel 4 channel 1 channel 1 channel PRX-MG08H 4 channel 8 channel 1 channel 1 channel PRX-MG16H 4 channel 16 channel 1 channel 1 channel PRX-MG16L N/A 16 channel 4 channel N/A

2 Overview and Controls

Overview and ControlsOverview and Controls

Overview and Controls

This section provides information about front panel and rear panel. When you install this series DVR for the first time, please refer to this part first.

2.1

2.12.1

2.1 Front Panel

Front PanelFront Panel

Front Panel

Figure 2-1

S/N Name Icon Function

Channel indication light

When DVR is recording this lamp turns on. Power button, press this button for three seconds to shut down DVR.

Standby indication light

When DVR is standing by, this lamp turns on.

Remote control signal receiver

To receive signals from remote control

Function indication light

In preview interface(no other menu), press this button for three seconds, you

can switch between TV/VGA output(HD1 series DVR has three modesLTV/VGA/60Hz LCD)

In textbox, click this button to switch between numeral, English(Small/Capitalized),donation, Chinese and etc.

Shift

←

←←

←

Open/close tour

numeral keys 0-9 0-9 Input password, switch channel and input numeral.

Input numeral more than10

When you need to input numeral more than 9. You can follow the steps below: click the first key number and then the next.

For example, input 123, click numeral 1 and then 2 and click 3(continuousl

y).

3 4 5 6 7

1 2

Slow play

Multiple slow play speeds or normal playback

Fast play



Various fast speeds and normal playback.

Play previous



In playback mode, playback the previous video In menu setup, go to upper ward of the dropdown list.

Reverse/Pause

⊳

In normal playback or pause mode, click this button to reverse playback In reverse playback, click this button to pause playback.

Play Next



In playback mode, playback the next video In menu setup, go to down ward of the dropdown list.

Reverse playback or paused mode, click this button to realize normal playback In normal playback click this button to pause playback In pause mode, click this button to resume playback

Play/Pause



In real-time monitor mode, click this button to enter video search menu

Up/down

、

Activate current control, modify setup, increase/decrease numeral, assistant function such as PTZ menu.

Left/right ⊳、

shift current activated control, When playback, click these buttons to control playback bar.

Cancel ESC Close upper interface or controls.

confirm operation Go to default button

Enter ENTER

Go to main menu

Record ●

Manually stop/start recording, working with direction keys or numeral keys.

Window switch MULT Switch between one-window and multiple-window display modes.

One-window monitor

mode, click this button to display assistant function:

PTZ control and image color. In PTZ menu, shift PTZ control menu.

Backspace function: in numeral control or text control, it can delete the previous character before the cursor.

In motion detection setup, working with Fn and direction keys to realize setup.

In HDD information menu, switch between HDD record time or other information(Menu prompt)

Assistant Fn

Realize other special functions

Shuttle(outer ring)

In real-time monitor mode it works as left/right direction key.

Playback mode, counter clockwise to forward and clock wise to backward

Jog(inner dial)

Up/down direction key. Playback mode, turn the inner dial to realized frame by frame playback. (only applies to some version.)

Power button POWER Power button, press this button for three seconds to shut down DVR.

Power indication light

Note: Turn shuttle (outer ring) clockwise stands for right, counter clockwise stands for left. Turn jog (Inner dial) clockwise stands for down, counter clockwise stands for up.

2.2

2.22.2

2.2 Rear Panel

Rear PanelRear Panel

Rear Panel

2.2.1 Overview

Please refer to Figure 2- for real panel information.

Figure 2-2

2.2.2 Connection Sample

Here is a connection sample for your reference. See Figure 2-.

Figure 2-3

2.3

2.32.3

2.3 Remote Control

Remote ControlRemote Control

Remote Control

The remote control interface is shown as in Figure 2-.

Figure 2-4

Serial Number Function 1 remote switch 2 Multiple-window switch 3 0-9 number key 4 Record 5 Auxiliary key 6 Confirm /menu key 7 Cancel 8 Direction key 9 forward 10 Previous 11 Back 12 Next 13 Slow play 14 Stop 15 Fast play 16 Play/Pause

2.4

2.42.4

2.4 Mouse Control

Mouse ControlMouse Control

Mouse Control

System pops up password input dialogue box if you have not logged in. In real-time monitor mode, you can go to the main menu. When you have selected one menu item, left click mouse to view menu content. Implement the control operation. Modify checkbox or motion detection status.

Left click mouse

Click combo box to pop up drop down list

In input box, you can select input methods. Left click the corresponding

button on the panel you can input numeral/English character (small/capitalized). Here ← stands for backspace button. ＿ stands for space button.

In English input mode: _stands for input a backspace icon and ← stands for deleting the previous character.

In numeral input mode: _ stands for clear and ← stands for deleting the previous numeral.

When input special sign, you can click corresponding numeral in the front panel to input. For example, click numeral 1 you can input“/” , or you can click the numeral in the on-screen keyboard directly.

Implement special control operation such as double click one item in the file list to playback the video.

Double left click mouse

In multiple-window mode, double left click one channel to view in full-window. Double left click current video again to go back to previous multiple-window mode.

In real-time monitor mode, pops up shortcut menu: one-window, four-window, nine-window and sixteen-window, Pan/Tilt/Zoom, color setting, search, record, alarm input, alarm output, main menu. Among which, Pan/Tilt/Zoom and color setting applies for current selected channel. If you are in multiple-window mode, system automatically switches to the corresponding channel.

Right click mouse

Exit current menu without saving the modification.

In numeral input box: Increase or decrease numeral value. Switch the items in the check box.

Press middle button

Page up or page down Move mouse

Select current control or move control

Select motion detection zone Drag mouse

Select privacy mask zone.

2.5

2.52.5

2.5 Virtual Keyboard & Front Panel

Virtual Keyboard & Front PanelVirtual Keyboard & Front Panel

Virtual Keyboard & Front Panel

2.5.1 Virtual Keyboard

The system supports two input methods: numeral input and English character (small and capitalized) input. Move the cursor to the text column, the text is shown as blue, input button pops up on the right. Click that button to switch between numeral input and English input (capitalized and small), Use > or < to shift between small character and capitalized character.

2.5.2 Front Panel

Move the cursor to the text column. Click Fn key and use direction keys to select number you wanted. Please click enter button to input.

3 Installation and Connections

Installation and ConnectionsInstallation and Connections

Installation and Connections

Note: All the installation and operations here should conform to your local electric safety rules.

3.1

3.13.1

3.1 Check Unpacked DVR

Check Unpacked DVRCheck Unpacked DVR

Check Unpacked DVR

When you receive the DVR from the shipping agency, please check whether there is any visible damage to the DVR appearance. The protective materials used for the package of the DVR can protect most accidental clashes during transportation. Then you can open the box to check the accessories. Please check the items in accordance with the list on the warranty card. Finally you can remove the protective film of the DVR.

3.2

3.23.2

3.2 HDD Installation

HDD Installation HDD Installation

HDD Installation

3.2.1 Choose HDDs

We recommend Seagate HDD of 7200rpm or higher.

3.2.2 Calculate HDD Size

This series have no limit to HDD capacity. You can use 120G-750G HDD to guarantee higher stability. The formula of total HDD size is: Total Capacity (MB) = Camera Amount * Recording Hours * HDD Usage Per Hour (M/h) H.264 compression is ideal for standalone DVRs. It can save more than 30% HDD capacity than MPEG4. When you calculate the total HD capacity, you should estimate the average HDD capacity per hour for each channel. For example, for a 4-ch DVR, the average capacity of HDD usage per hour per channel is 200M/h. Now if you hope the DVR can record the video 12 hours each day for 30 days, the total capacity of HDDs needed is: 4 channels * 30 days * 12 hours * 200 M/h = 288G. So you need to install one 300G HDD or 2 160G HDDs.

3.2.3 HDD Installation

Data ribbons, fastening screws and smart HDD shelf design are already provided in the accessories.

Please follow the instructions below to install hard disk.

1. Loosen the screws of the upper cover. 2. Remove the HDD bracket from internal unit.

3. Dismantle the upper HDD bracket. 4. Install the HDD. Note the HDD is placed

upside down. Please make sure bracket is in correct position.

If the HDD amount is less than four, you do not need to install the HDD bracket.

Screw the two bracket parts together. 6. Put HDD bracket back and then fix firmly.

7. Loosen the power cable. 8. Connect to the SATA ports and then connect power cord to the HDDs.

9. Place the upper cover back and screw firmly.

After HDD installation, please check connection of data ribbon and power cord.

3.3

3.33.3

3.3 CD

CDCD

CD/DVD

/DVD/DVD

/DVD Burner

Burner Burner

Burner Installation

Installation Installation

Installation

For built-in burner, you can dismantle front plate to install CD burner. This built-in burner should be set as MASTER. For USB burners, you need to install USB series burner. This series DVR is compatible with various burner brands popular in today’s market. You can consult our local technical support or visit our website for more information.

3.4

3.43.4

3.4 D

Desktop and Rack

esktop and Rackesktop and Rack

esktop and Rack M

M M

Mounting

ountingounting

ounting

3.4.1 Desktop Mounting

To prevent surface damage, please make sure that the rubber feet are securely installed on the four corners of the bottom of the unit. Position the unit to allow for cable and power cord clearance at the rear of the unit. Be sure that the air flow around the unit is not obstructed.

3.4.2 Rack Mounting

The DVR occupies two rack units of vertical rack space. The hardware necessary to mount the DVR into a rack is supplied with the unit. Rear doors may be used only on rack columns that are more than 26 inches (66.0 cm) deep. Install the cabinet in ventilated place. Avoid extreme heat, humid or dusty conditions. You can use a soft dry brush to clean opening outlet, cooling fan and etc regularly.

3.5

3.53.5

3.5 Connecting

Connecting Connecting

Connecting Power

Power Power

Power Supply

SupplySupply

Supply

Please check input voltage and device power button match or not. We recommend you use UPS to guarantee steady operation, DVR life span, and other peripheral equipments operation such as cameras.

3.6

3.63.6

3.6

CCC

Connecting

onnectingonnecting

onnecting V

V V

Video

ideoideo

ideo I

I I

Input

nputnput

nput and

andand

and O

O O

Output

utpututput

utput D

D D

Devices

evicesevices

evices

3.6.1 Connecting Video Input

The DVR automatically detects the video standard (PAL or NTSC) whenever you connect a video input. It accepts both color and black-and-white and analog video. NOTE:  Enabling line lock on cameras may cause video distortion. There may be noise in

the camera’s power source. If video from one or more cameras is distorted, we recommend you disable line lock on the camera as your first troubleshooting step.

 If a video distribution amplifier is installed between the video source and the DVR,

do not set the output video level above 1 Vp-p.

To connect each video input:

1. Connect a coaxial cable to the camera or other analog video source.

2. Connect the coaxial cable to the video in connector on the rear panel. Please refer to Figure 3-1 for more information.

NOTE:

You need to use a BNC installation tool to connect coaxial cables to the rear panel.

Figure 3-1

3.6.2 Connecting Video Output

This section provides information about physically connecting video display devices to the DVR. See Figure 3-2. If you connect the DVR with a TV monitor or VGA monitor, the DVR can automatically detects the monitor type. And without any output device, by default, the DVR is configured to use a TV monitor. In this case, if your application requires a VGA monitor, you have to press the button “FN” or Shift on the front panel.

NOTE:

Video output 1 and VGA can’t display at the same time. But Video output 2 can display properly with Video Output 1 or VGA.

Figure 3-2

3.7

3.73.7

3.7 C

Connecting

onnectingonnecting

onnecting Audio Input

Audio Input Audio Input

Audio Input &

& &

& Output

OutputOutput

Output, Bidirectional Audio, Looping

, Bidirectional Audio, Looping , Bidirectional Audio, Looping

, Bidirectional Audio, Looping

Video

VideoVideo

Video, Matrix

, Matrix, Matrix

, Matrix

For the 25-pin or 37-pin interface, different models include different functions. For example, PRX-MG16H has 4 audio inputs, 1 audio output, I bidirectional audio input. See Figure 3-3.

Figure 3-3

3.7.1 Audio Input/One Audio Output

PRX-MG16H has 16 looping video inputs, 1 matrix video outputs, 4 audio inputs, I bidirectional audio input, 1 audio output. Audio input, bidirectional audio input and audio output The DVR encodes audio and video signals simultaneously, which lets you control audio at the monitored location. To set up audio:

1. Make sure your audio input device matches the RCA input level. If the device and RCA input levels do not match, audio distortion problems may occur.

2. Make sure the audio connector is wired as follows:

3. Connect a line input device or pre-amplified microphone to the audio connector for the video channel on the rear panel. Please refer to Figure 3-4.

Figure 3-4

3.7.2 Looping video

The DVR supports looping video. It passes the video input to a monitor or other analog video device. To use looping video:

1. Connect a coaxial cable to the video out connector on 37-pin interface

Please note you need to use a BNC installation tool to connect coaxial cables to the rear panel.

2. Connect the other end of the coaxial cable to the analog device.

3.7.3 Matrix Video Output

Use video matrix output connector during installation to display video sequentially from each video input. The unit displays each channel for selected seconds. You can use this feature to verify camera installation. To display video from each connected video source:

1. Connect a video monitor to the video matrix output connector.

2. Turn the DVR on, the monitor, and each video matrix output source.

3. Verify the video from each source and troubleshoot as necessary. Please refer to Figure 3-5.

Figure 3-5

3.7.4 Alarm Input and Relay Output

The DVR offers 16 alarm inputs for external signaling devices, such as door contacts or motion detectors. Each alarm input can be either normally open or normally closed. Once configured, an alarm input can invoke many different activities, including triggering a relay device, sending an alert to a security office or storing pre-alarm video to the DVR.

3.7.5 Alarm Input

You should check your alarm input mode is grounding alarm input or not. For this series DVR, grounding signal is needed for alarm input. If you need to connect two units or one DVR and other device, please use relay to separate them. Please refer to Figure 3-6 for more information.

Figure 3-6

3.7.6 Alarm Output

Do not connect alarm output port directly with high power load (no more than 1 A) in case of heavy current. You can use the co-contactor to realize the connection between the alarm output port and the load. Please refer to Figure 3-7 for more information.

Figure 3-7

3.7.7 Alarm Input and Output Details

You can refer to the following sheet and Figure 3-8 for alarm input and output information.

Parameter

Grounding Alarm

Ground Ground line Alarm Input

1, 2, …, 16

Relay Output 1,2,3,4: NO and C(Normally Open and Com)

5: NO,C and NC(Normally Open, Com, Normally Closed) 6: Ctrl 12V(This is used for reset the senor)

485 A、B

485 communication port. They are used to control devices

such as PTZ.

+12（C）

This should input an external power input.

 4/8/16-ch grounding alarm inputs. (Normal open or Normal close type)  Please parallel connect COM end and GND end of the alarm detector (Provide

external power to the alarm detector).

 Please parallel connect the Ground of the DVR and the ground of the alarm

detector.

 Please connect the NC port of the alarm sensor to the DVR alarm input(ALARM)  If you need to reset the touched-off alarm remotely, you can use DVR to supply

controllable 12 V power to the alarm detector such as the smoke detector.

 Use the same ground with that of DVR if you use external power to the alarm

device.

Figure 3-8

3.7.8 Relay Output Description

 6 ways relay alarm output. Provide external power to external alarm device.  To avoid over loading, please read the following relay parameters sheet carefully.

(See below table)  The controllable +12v can be used to restore the smoke detector. Please refer to Figure 3-9 for alarm input module information.

Figure 3-9

Please refer to Figure 3-10 for alarm output module information.

Figure 3-10

Relay Specification

Model:

JRC-27F

Material of the touch

Silver

Rated switch capacity 30VDC 2A, 125VAC 1A Maximum switch power 125VA 160W Maximum switch voltage 250VAC, 220VDC

Rating （resistance load）

Maximum switch currency 1A between touches with

same polarity

1000VAC 1minute 50/60Hz

between touches with different polarity

1000VAC 1minute 50/60Hz

Insulation

between touch and winding 1000VAC 1minute 50/60Hz

Surge voltage

between touches with same polarity

1500V (10×160us)

Length of open time

3ms max

Length of close time

3ms max

Mechanical

50×106 times (3Hz)

Longevity

Electrical

200×103 times (0.5Hz)

Temperature

-40 ~+70

3.8

3.83.8

3.8 RS232

RS232RS232

RS232

You can connect the DVR with POS or Keyboard through RS232. With POS system, the DVR can communicate through RS232 and network. For the POS system, the DVR can integrate the text content and even search the record through the info.

The series DVR also support NKB operation. You can operate the DVR from the keyboard controls instead of using the control pad on the front panel of the unit. To connect a NKB keyboard to the DVR:

1. Assemble the KBD keyboard according to the instructions in its accompanying installation manual.

2. Connect the KBD keyboard into one of the RS232 ports on the DVR or through network.

3.9

3.93.9

3.9 RS485

RS485RS485

RS485

When the DVR receives a camera control command, it transmits that command up the coaxial cable to the PTZ device. RS485 is a single-direction protocol; the PTZ device can’t return any data to the unit. To enable the operation, connect the PTZ device to the RS485(A,B) input on the DVR. Since RS485 is disabled by default for each camera, you must enable the PTZ settings first. This series DVRs support multiple protocols such as Pelco-D, Pelco-P. To connect PTZ devices to the DVR:

1. Connect RS485 A,B on the DVR rear panel.

2. Connect the other end of the cable to the proper pins in the connector on the camera.

3. Follow the instructions for configuring a camera to enable each PTZ device on the DVR.

3.10

3.103.10

3.10

Other Interfaces

Other InterfacesOther Interfaces

Other Interfaces

There are still other interfaces on the DVR, such as USB ports. You can refer to the Figure 3-11 for more information.

Figure 3-11

4 Overview of Navigation and Controls

Overview of Navigation and Controls Overview of Navigation and Controls

Overview of Navigation and Controls

Before operation, please make sure you have properly installed HDDs and all the cable connections.

4.1

4.14.1

4.1 Login, Logout & Main Menu

4.1.1 Login

When the system boots up, default video display is in multiple-window mode. Click Enter or left click mouse, you can see the login interface. See Figure 4-1. System consists of four accounts:

 Username: admin. Password: admin. (administrator, local and network)  Username: 888888. Password: 888888. (administrator, local only)  Username: 666666. Passwords: 666666(Lower authority user who can only

monitor, playback, backup and etc.)  Username: default. Password: default(hidden user) For your system security, please modify you password after first login. You can use USB mouse, front panel, remote controller or keyboard to input.

About input method: Click to switch between numeral, English character (small/capitalized) and denotation.

Note: Three times login failure in 30 minutes will result in system alarm and five times login failure will result in account lock!

Figure 4-1

4.1.2 Main Menu

After you logged in, the system main menu is shown as below. See Figure 4-2. There are total six icons: search, information, setting, backup, advanced and shutdown. You can move the cursor to highlight the icon, and then double click mouse to enter the sub-menu.

Figure 4-2

4.1.3 Logout

There are two ways for you to log out. One is from menu option: In the main menu, click shutdown button, you can see an interface is shown as below. See Figure 4-3.

Figure 4-3

There are several options for you. See Figure 4-4.

Figure 4-4

The other ways is to press power button on the front panel for at least 3 seconds, system will stop all operations. Then you can click the power button in the rear panel to turn off the DVR.

4.1.4 Auto Resume after Power Failure

The system can automatically backup video and resume previous working status after power failure.

4.1.5 Replace Button Battery

Please make sure to use the same battery model if possible. We recommend replace battery regularly (such as one-year) to guarantee system time accuracy.

4.2

4.24.2

4.2 Record

Record Record

Recording O

ing Oing O

ing Operation

peration peration

peration

4.2.1 Live Viewing

When you login, the system is in live viewing mode. You can see system date, time and channel name. If you want to change system date and time, you can refer to general settings (Main Menu->Setting->General). If you want to modify the channel name, please refer to the display settings (Main Menu->Setting>Display)

Note: Please refer to the following sheet for channel status. stands for opening switch function, stands for closing switch function.

4.2.2 Manual record Note:

You need to have proper rights to implement the following operations. Please make sure the HDDs have been properly installed.

4.2.2.1 Manual record menu There are two ways for you to go to manual record menu.

 Right click mouse or in the main menu, Advanced->Manual Record.  In live viewing mode, click record button in the front panel or record button in the

remote control. Manual record menu is shown as in Figure 4-5.

4.2.2.2 Basic operation There are three statuses: schedule/manual/stop. Highlight icon“○” to select corresponding channel.  Manual: the highest priority. After manual setup, all selected channels will begin

ordinary recording.  Schedule: channel records as you have set in recording setup (Main Menu-

>Setting->Schedule)  Stop: all channels stop recording.

Figure 4-5

4.2.2.3 Enable/disable record Please check current channel status: “○” means it is not in recording status, “●” means it is in recording status. You can use mouse or direction key to highlight channel number. See Figure 4-6.

1111

Recording status

3333

Video loss

2222

Motion detection

4444

Camera lock

Figure 4-6

4.2.2.4 Enable all channel recording Highlight ○ below All, you can enable all channel recording.

 All channel schedule record Please highlight “ALL” after “Schedule”. See Figure 4-7. When system is in schedule recording, all channels will record as you have previously set (Main menu->Setting->Schedule). The corresponding indication light in front panel will turn on.

Figure 4-7

 All channel manual record Please highlight “ALL” after “Manual.” See Figure 4-8. When system is in manual recording, all scheduled set up you have set in will be null ((Main menu->Setting->Schedule)). You can see indication light in front panel turns on, system begins manual record now.

Figure 4-8

4.2.2.5 Stop all channel recording Please highlight “ALL” after “Stop”. See Figure 4-9. System stops all channel recording no matter what mode you have set in the menu (Main menu->Setting->Schedule)

Figure 4-9

4.3

4.34.3

4.3

Search Search

Search & Playback

& Playback& Playback

& Playback

4.3.1 Search Menu

There are two ways for you to go to search menu.

 Click Pause/Play button in the remote control.  Click search in the main menu.

Search interface is shown as below. See Figure 4-10. Usually there are three file types:

 R: regular recording file.  A: external alarm recording file.  M: motion detection recording file  C: card and pos test overlay recording file(For some special series only)

There are several playback windows. System supports 1/2-ch playback.

Figure 4-10

Please refer to the following sheet for more information.

Serial Number Function

1 Play 2 Backward 3 Stop 4 Slow play 5 Fast play 6 Previous frame 7 Next frame 8 Volume 9 Previous file 10 Next channel 11 Next file 12 Previous channel 13 Search 14 Backup

These series DVRs support 2-channel simultaneous playback.

4.3.2 Basic Operation

4.3.2.1 Playback There are various search modes: video type, channel number or time. The system can max display 128 files in one screen. You can use page up/down button to view if there are more than one page. Select the file name and double click mouse (or click enter button), you can view file content.

4.3.2.2 Accurate playback Input time (h/m/s) in the time column and then click playback button, system can operate accurate playback.

4.3.2.3 Synchronized playback function when playback During playback process, click numeral key, system can switch to the corresponding channel video of the same time.

4.3.2.4 Digital zoom When the system is in full-screen playback mode, drag your mouse in the screen to select a section and then left click mouse to realize digital zoom. You can right click mouse to exit.

4.3.2.5 File backup System supports backup operation during search. You can draw a √ before file name (multiple choices). Then click backup button (Button 14 in Figure 4-10).

4.3.2.6 Slow playback and fast playback Please refer to the following sheet for slow play and fast playback function.

Button Illustration Remarks

Fast play button  In playback mode, click this button to

switch between various fast play modes such as fast play 1,fast play 2 and more.(Fast play 1 means fast play level 1 or not about speed)

Frame rate may vary due to different versions.

Slow play button ► (Or you can turn the outer ring counter clockwise.)

In playback mode, click this button to switch between various slow play modes such as slow play 1 or slow play 2.

3、Play/Pause►

In slow playback mode, click this button to switch between play/pause modes.

4、Previous/next

In playback mode, you can click 

and  to view previous or next video in current channel.

4.3.2.7 Fast forward/fast backward and frame by frame playback

Special Functions of Shuttle and Jog

Illustration

Remarks

Fast forward(outer ring clockwise)

When playback, turn the shuttle (outer ring) clockwise one round: you can view in fast level 1 Turn it two rounds you get fast level 2. You can continue turning to get different speed.

Fast backward(outer ring counter clockwise)

When playback, turn the shuttle (outer ring) counter clock-wise one round, you can view in backward level 1. Turn it two rounds, you get backward level 2. You can continue turning to get different speed.

In forward or backward mode, double click Pause/Play button to get normal playback.

Frame rate may vary due to different version.

Manual playback frame by frame

In playback mode, click play/pause button, slowly turn the jog (inner dial) clock-wise to view frame by frame, counter clock wise to view I frame playback.

4.3.2.8 Backward playback and frame by frame playback

Button Illustration Remarks

Backward play  in playback interface.

In normal playback mode, left click backward play button, system begins backward playback. Double click backward play button again, system goes to pause mode.

Manual playback frame by frame.

Click pause button in normal playback mode, slowly turn the jog (inner dial) clock-wise to view frame by frame, counter clock wise to view I frame playback.

When system is in backward play or frame by frame playback mode, you can click play button to go to normal playback.

Note: All the operations here (such as playback speed, channel, time and progress) have relationship with hardware version. Some series DVRs do not support some functions or playback speeds.

4.3.3 Calendar

Click calendar icon in Figure 4-10, system pops up calendar for your reference.

Highlighted date means that there are record files in that day. You can click blue date to view file list. In Figure 4-11, there are video files in March 13th and 14th. Double click the date to view file list.

Figure 4-11

4.4

4.44.4

4.4 Record Setup (Schedule)

Record Setup (Schedule)Record Setup (Schedule)

Record Setup (Schedule)

When the system boots up, it is in default 24-hour regular mode. You can set record type and time in schedule interface.

4.4.1 Schedule Menu

In the main menu, from setting to schedule, you can go to schedule menu. See Figure 4-12. There are three record types: R-Regular, MD-Motion detection, A- Alarm.

Figure 4-12

4.4.2 Basic Operation

There are total six periods. See Figure 4-12.

 Channel: Please select the channel number first. You can select “all” if you want

to set for the whole channels.

 Week day: There are eight options: ranges from Saturday to Sunday and all.  Redundancy: System supports redundancy backup function. You can highlight

Redundancy button to activate this function. Please note, before enable this

function, please set at least one HDD as redundant.(Main menu->Advanced-

>HDD Management)

 Snapshoot: You can enable this function to snapshoot image when alarm occurs.  Record types: There are three types: regular, motion detection (MD) and Alarm.

Please highlight icon to select the corresponding function. After all the setups please click save button, system goes back to the previous menu.

At the bottom of the menu, there are color bars for your reference. Green stands for regular recording, yellow stands for motion detection and red stands for alarm recording.

4.4.1.1 Quick Setup This function allows you to copy one channel setup to another. After setting in channel 1, you can click paste button and turn to channel 2 and then click copy button. You can finish setting for one channel and then click save button or you can finish all setup and then click save button to memorize all the settings.

4.4.1.2 Redundancy Redundancy function allows you to memorize record file in several disks. These files are created, packaged and closed simultaneously. When there is file damage occurred in one disk, there is a spare one in the other disk. You can use this function to maintain data reliability and safety. In the main menu, from Setting to Schedule, you can highlight redundancy button to enable this function. See Figure 4-12. In the main menu, from Advanced to HDD management, you can set one or more disk(s) as redundant. You can select from the dropdown list. See Figure 4-13. System auto overwrites old files once hard disk is full. Please note only read/write disk or read-only disk can backup file and support file search function, so you need to set at least one read-write disk otherwise you can not record video.

Note About redundancy setup:

 If current channel is not recording, current setup gets activated when the channel

begin recording the next time.  If current channel is recording now, current setup will get activated right away, the

current file will be packet and form a file, then system begins recording as you

have just set. After all the setups please click save button, system goes back to the previous menu.

Figure 4-13

Playback or search in the redundant disk.

There are two ways for you to playback or search in the redundant disk.  Set redundant disk(s) as read-only disk or read-write disk (Main menu-

>Advanced->HDD management). See Figure 4-13.System needs to reboot to get

setup activated. Now you can search or playback file in redundant disk.  Dismantle the disk and play it in another PC.

4.5

4.54.5

4.5 Detect

Detect Detect

Detect

4.5.1 Go to Detect Menu

In the main menu, from Setting to Detect, you can see motion detect interface. See Figure 4-14. There are three detection types: motion detection, video loss, camera masking.

4.5.2 Motion Detect

Detection menu is shown as below. See Figure 4-14.

 Channel: select the channel you want to implement motion detection.  Event type: from the dropdown list you can select motion detection type.  Channel: select the channel to activate recording function once alarm occurred.

Please make sure you have set MD record in encode interface(Main Menu-

>Setting->Schedule) and schedule record in manual record interface(Main Menu-

>Advanced->Manual Record)  Latch: when motion detection complete, system auto delays detecting for a

specified time. The value ranges from 10-300(Unit: second)  Region: Click select button, the interface is shown as in Figure 4-15.Here you can

set motion detection zone. There are 396(PAL)/330(NTSC) small zones.

 Sensitivity: System supports 6 levels. The sixth level has the highest sensitivity.  Show message: System can pop up a message to alarm you in the local host

screen if you enabled this function.  Send email: System can send out email to alert you when alarm occurs.

 PTZ activation: Here you can set PTZ movement when alarm occurs. Such as go

to preset, tour &pattern when there is an alarm. Click “select” button, you can see

an interface is shown as in Figure 4-16.  Period: Click set button, you can see an interface is shown as in Figure 4-17.

Here you can set for business day and non-business day. In Figure 4-17, click set

button, you can see an interface is shown as in Figure 4-18. Here you can set

your own setup for business day and non-business day.

 Anti-dither: Here you can set anti-dither time.  Sensitivity: there are six levels. The sixth level has the highest sensitivity.  Alarm output: when alarm occurred, system enables peripheral alarm devices.  Tour: Here you can enable tour function when alarm occurs. It is a one-window

tour. Please go to chapter 5.3.9 Display for tour interval setup.  Snapshot: System can snapshoot when alarm occurs.

Please highlight icon to select the corresponding function. After all the setups please click save button, system goes back to the previous menu.

Note: In motion detection mode, you can not use copy/paste to set channel setup since the video in each channel may not be the same. In Figure 4-15, you can left click mouse and then drag it to set a region for motion detection. Click Fn to switch between arm/withdraw motion detection. After setting, click enter button to exit.

Figure 4-14

Figure 4-15

Figure 4-16

Figure 4-17

Figure 4-18

4.5.3 Video Loss

In Figure 4-14, select video loss from the type list. You can see the interface is shown as in Figure 4-19.This function allows you to be informed when video loss phenomenon occurred. You can enable alarm output channel and then enable show message function.

 Channel: select the channel you want to enable lens shading alarm.  Event type: please select video loss.  Channel: select the channel to record when video loss occurred.  Alarm output: activate peripheral alarm device when video loss occurred.  Latch: when motion detection complete, system auto delays detecting for a

specified time. The value ranges from 10-300(Unit: second)  Show message: System can pop up a message to alarm you in the local host

screen if you enabled this function.

 Send email: System can send out email to alert you when alarm occurs.  PTZ activation: Here you can set PTZ movement when alarm occurs. Such as go

to preset, tour & pattern when there is an alarm. Click “select” button, you can

see an interface is shown as in Figure 4-16.  Period: Click set button, you can see an interface is shown as in Figure 4-17.

Here you can set for business day and non-business day. In Figure 4-17, click set

button, you can see an interface is shown as in Figure 4-18. Here you can set

your own setup for business day and non-business day.

 Sensitivity: there are six levels. The sixth level has the highest sensitivity.  Alarm output: when alarm occurred, system enables peripheral alarm devices.  Tour; Here you can enable tour function when alarm occurs. It is a one-window

tour. Please go to chapter 5.3.9 Display for tour interval setup.  Snapshot: System can snapshoot when alarm occurs.

Figure 4-19

4.5.4 Camera Masking

When someone viciously masks lens, the system can alert you to guarantee video continuity. Camera masking interface is shown as in Figure 4-20.

 Channel: select the channel you want to enable camera mask detection function.  Event type: please select camera mask detect from the dropdown list.  Channel: select the channel to record when camera mask occurred.  Alarm output: activate peripheral alarm device when camera mask occurred.  Enable tour: Here is for you to activate tour between different cameras.  Latch: when motion detection complete, system auto delays detecting for a

specified time. The value ranges from 10-300(Unit: second)  Show message: System can pop up a message to alarm you in the local host

screen if you enabled this function.

 Send email: System can send out email to alert you when alarm occurs.  PTZ activation: Here you can set PTZ movement when alarm occurs. Such as go

to preset, tour &pattern when there is an alarm. Click “select” button, you can see

an interface is shown as in Figure 4-16.  Period: Click set button, you can see an interface is shown as in Figure 4-17.

Here you can set for business day and non-business day. In Figure 4-17, click set

button, you can see an interface is shown as in Figure 4-18. Here you can set

your own setup for business day and non-business day.

 Sensitivity: there are six levels. The six-level has the highest sensitivity.  Alarm output: when alarm occurred, system enables peripheral alarm devices.  Tour: Here you can enable tour function when alarm occurs. It is a one-window

tour: Please go to chapter 5.3.9 Display for tour interval setup.  Snapshoot: System can snapshoot when alarm occurs.

Note:

In this interface, copy/paste function is only valid for the same type, which means you can not copy a channel setup in video loss mode to camera masking mode.

Figure 4-20

4.6

4.64.6

4.6 A

Alarm Setup and Alarm Activation

larm Setup and Alarm Activation larm Setup and Alarm Activation

larm Setup and Alarm Activation

Before operation, please make sure you have properly connected alarm devices such as buzzer.

4.6.1 Go to alarm setup interface

In the main menu, from Setting to Alarm, you can see alarm setup interface. See Figure 4-21.

4.6.2 Alarm setup

Alarm interface is shown as below. See Figure 4-21.

 Alarm in: here is for you to select channel number.  Event type: there are two types. One is local input and the other is network input.  Type: normal open or normal close.  PTZ activation: Here you can set PTZ movement when alarm occurs. Such as go

to preset, tour& pattern when there is an alarm. Click “select” button, you can see

an interface is shown as in Figure 4-25.  Period: Click set button, you can see an interface is shown as in Figure 4-23.

Here you can set for business day and non-business day. In Figure 4-26, click set

button, you can see an interface is shown as in Figure 4-27. Here you can set

your own setup for business day and non-business day.

 Anti-dither: Here you can set anti-dither time.  Show message: System can pop up a message to alarm you in the local host

screen if you enabled this function.

 Send email: System can send out email to alert you when alarm occurs.  Record channel: you can select proper channel to record alarm video (Multiple

choices). At the same time you need to set alarm record in schedule interface

(Main Menu->Setting->Schedule) and select schedule record in manual record

interface (Main Menu->Advance->Manual Record).

 Latch: Here is for you to set proper delay duration. Value ranges from 10 to 300

seconds. System automatically delays specified seconds in turning off alarm and

activated output after external alarm cancelled.  Tour: Here you can enable tour function when alarm occurs. It is a one-window

tour: Please go to chapter 5.3.9 Display for tour interval setup.  Snapshot: System can snapshoot when alarm occurs.

Please highlight icon to select the corresponding function. After all the setups please click save button, system goes back to the previous menu.

Figure 4-21

Figure 4-22

Figure 4-23

Figure 4-24

4.7

4.74.7

4.7 Backup

Backup Backup

Backup

DVR support various backup devices such as CD-RW,DVD driver, USB backup and network download. Here we introduce USB backup first. You can refer to Chapter 7 Web Client Operation for network download backup operation.

4.7.1 Detect Device

Click backup button, you can see an interface is shown as in Figure 4-25. Here is for you to view devices information.

Figure 4-25

4.7.1 Backup

Select backup device and then channel, file start time and end time. Click add button, system begins search. All matched files are listed below. System automatically calculates the capacity needed and remained. See Figure 4-26. system only backup files with a √ before channel name. You can use Fn or cancel button to delete √ after file serial number. Click backup button, you can backup selected files. There is a process bar for you reference. When the system completes backup, you can see a dialogue box prompting successful backup.

Figure 4-26

Click backup button, system begins burning. At the same time, the backup button becomes stop button. You can view the remaining time and process bar at the left bottom. See Figure 4-27.

Figure 4-27

Tips:

During backup process, you can click ESC to exit current interface; but the system will not terminate backup process.

Note:

When you click stop button during the burning process, there are two conditions for different devices:

 For CD/DVD burner device, the stop function becomes activated immediately and

there is no data in the burner.  For USB device, system can backup the data before you click stop button. For

example, if there is a file of 10 minutes, when you click stop after five minutes

backup, system only save the previous 5-minute data in the device. The file name format usually is: SN_CH+channel number+time Y+M+D+H+M+S. In the file name, the YDM format is the same as you set in general interface. (Main Menu ->Setting ->General).You can visit our website to view listed CDROM type.

4.8

4.84.8

4.8 PTZ Control and Color Setup

PTZ Control and Color SetupPTZ Control and Color Setup

PTZ Control and Color Setup

Note: All the operations here are based on PELCOD protocol. For other protocols, there might be a little difference.

4.8.1 Cable Connection

Please follow the procedures below to go on cable connection

 Connect the dome RS485 port to DVR 485 port.  Connect dome video output cable to DVR video input port.  Connect power adapter to the dome.

4.8.2 PTZ Setup Note: The camera video should be in the current screen. Before setup, please

check the following connections are right:

 PTZ and decoder connection is right. Decoder address setup is right.  Decoder A (B) line connects with DVR A (B) line.

Boot up the DVR, input user name and password. In the main menu, click setting, and then click Pan/Tilt Control button. The interface is shown as in Figure 4-28. Here you can set the following items:

 Channel: select the current camera channel.  Protocol: select corresponding PTZ protocol(such as PELCOD)  Address: default address is 1.  Baud rate: select corresponding baud rate. Default value is 9600.  Data bits: select corresponding data bits. Default value is 8.  Stop bits: select corresponding stop bits. Default value is 1.  Parity: there are three options: odd/even/none. Default setup is none.

Figure 4-28

After all the setting please click save button. In one window display mode, right click mouse (click “Fn” Button in the front panel or click “Fn” key in the remote control). The interface is shown as in Figure 4-29.

Figure 4-29

Click Pan/Tilt/Zoom, the interface is shown as below. See Figure 4-30. Here you can set the following items:

 Step: value ranges fro 1 to 8.  Zoom  Focus  Iris

Click icon and to adjust zoom, focus and iris.

Figure 4-30

In Figure 4-30, please click direction arrows (See Figure 4-31) to adjust PTZ position. There are total 8 direction arrows.

Figure 4-31

4.8.3 3D Intelligent Positioning Key

In the middle of the eight direction arrows, there is a 3D intelligent positioning key. See Figure 4-32. Click this key, system goes back to the single screen mode. Drag the mouse in the screen to adjust section size. It can realize PTZ automatically.

Figure 4-32

Here is a sheet for you reference.

Name Function

key

function Shortcut

key

Function key

function Shortcut

Key

Zoom

Near ►

Far



Focus

Near 

Far

►

Iris

⊳

Open



4.9

4.94.9

4.9 Preset

PresetPreset

Preset//// PPPPatrol

atrolatrol

atrol/P

/P/P

/Pattern

atternattern

attern/Scan

/Scan/Scan

/Scan

In Figure 4-30, click the “set” button. The interface is shown as below. See Figure 4-33. Here you can set the following items:

 Preset  Tour  Pattern  Border

Figure 4-33

In Figure 4-30, click page switch button, the interface is shown as in Figure 4-34. Here you can activate the following functions:

 Preset  Tour  Pattern  Auto scan  Auto pan  Flip  Reset  Page switch

Figure 4-34

Note: The following setups are usually operated in the Figure 4-30,Figure 4-33 and Figure 4-34 .

4.9.1Preset Setup

In Figure 4-30, use eight direction arrows to adjust camera to the proper position. In Figure 4-33, click preset button and input preset number. The interface is shown as in Figure 4-35. Now you can add this preset to one tour.

Figure 4-35

4.9.2 Activate Preset

In Figure 4-34, please input preset number in the No. blank, and click preset button.

4.9.3 Patrol setup (Tour Setup)

In Figure 4-33, click patrol button. The interface is shown as in Figure 4-36.Input preset number and add this preset to a patrol (tour). For each patrol (tour), you can input max 80 presets.

Figure 4-36

4.9.4 Activate Patrol (tour)

In Figure 4-33, input patrol (tour) number in the No. blank and click patrol button

4.9.5 Pattern Setup

In Figure 4-33, click pattern button and then click “begin” button. The interface is shown as in Figure 4-37. Then you can go to Figure 4-30 to modify zoom, focus, and iris. Go back to Figure 4-37 and click “end” button. You can memorize all these operations as pattern 1.

Figure 4-37

4.9.6 Activate Pattern Function

In Figure 4-34, input mode value in the No. blank, and click pattern button.

4.9.7 Auto Scan Setup

In Figure 4-33, click border button. The interface is shown as in Figure 4-28. Please go to Figure 4-30, use direction arrows to select camera left limit Then please go to Figure 4-38 and click left limit button Repeat the above procedures to set right limit.

Figure 4-38

4.9.8 Activate Auto Scan

In Figure 4-34, click “Auto Scan” button, the system begins auto scan. Correspondingly, the auto scan button becomes to stop button. Click stop button to terminate scan operation.

4.10

4.104.10

4.10

Flip

FlipFlip

Flip

In Figure 4-34, click page switch button, you can see an interface is shown as below. See Figure 4-39. Here you can set auxiliary function. Click page switch button again, system goes back to Figure 4-30.

Figure 4-39

5 Understanding of

Understanding of Understanding of

Understanding of Menu

Menu Menu

Menu Operations and Controls

Operations and ControlsOperations and Controls

Operations and Controls

5.1

5.15.1

5.1 Menu

Menu Menu

Menu TTTTree

reeree

ree

This series DVR menu tree is shown as below.

5.2

5.25.2

5.2 Main

Main Main

Main MMMMenu

enu enu

enu

After you logged in, the system main menu is shown as below. See Figure 5-1 . There are total six icons: search, Information, setting, backup, advanced and shutdown. Move the cursor to highlight the icon, then double click mouse to enter the sub-menu.

Figure 5-1

5.3

5.35.3

5.3 S

Setting

ettingetting

etting

In main menu, highlight setting icon and double click mouse. System setting interface is shown as below. See Figure 5-2.

Figure 5-2

5.3.1 General

General setting includes the following items. See Figure 5-3.

 System time: here is for you to set system time  Date format: there are three types: YYYYY-MM-DD: MM-DD-YYYYY or DD-MM-

YYYY.  Date separator: there are three denotations to separate date: dot, beeline and

solidus.  Snapshoot: Here you can set image upload interval. (This function applies to

some series only).  DST: Here you can set DST time and date. Please enable DST function and then

click set button. You can see an interface is shown as in Figure 5-4. Here you can

set start time and end time by setting corresponding week setup. In Figure 5-4,

enable date button, you can see an interface is shown as in Figure 5-5. Here you

can set start time and end time by setting corresponding date setup.  Time format: there are two types: 24-hour mode or 12-hour mode.

 Language: system supports various languages: Chinese (simplified), Chinese

(Traditional), English, Italian, Japanese, French, Spanish (All languages listed

here are optional. Slight difference maybe found in various series.)  HDD full: Here is for you to select working mode when hard disk is full. There are

two options: stop recording or rewrite.  Pack duration: Here is for you to specify record duration. Default value is 60

minutes.  DVR No: when you are using one remote control to control several DVRs, you

can give a name to each DVR for your management.

 Video standard: There are two formats: NTSC and PAL.  Auto logout: Here is for you to set auto logout interval once login user remains

inactive for a specified time. Value ranges from 0 to 60 minutes.

Note:

Since system time is very important, do not modify time casually unless there is a must! After completing all the setups please click save button, system goes back to the previous menu.

Figure 5-3

Figure 5-4

Figure 5-5

5.3.2 Encode

Encode setting includes the following items. See Figure 5-6. Please note some series do not support extra stream.

 Channel: Select the channel you want.  Compression: system supports H.264. Or you can select from the dropdown list.  Resolution: System supports various resolutions, you can select from the

dropdown list. For this model, we can support D1/CIF.  Bit rate: system supports two types: CBR and VBR. In VBR mode, you can set

video quality.  Quality: There are six levels ranging from 1 to 6. The sixth level has the highest

image quality.  Frame rate: there are six levels: 1 f/s,2f/s,3f/s, 6f/s,12f/s,25f/s. (Some series

DVRs only support PAL 25f/s )  Video/audio: you can enable or disable the video/audio respectively for the main

stream and extra stream.

 Overlay: click overlay button, you can see an interface is shown in Figure 5-7.  Cover area (Privacy mask): Here is for you to set window blanking section. You

can drag you mouse to set proper section size.  Preview/monitor: privacy mask has two types. Preview means the privacy mask

zone can not be viewed by user when system is in preview status. Monitor means

the privacy mask zone can not be view by the user when system is in monitor

status.

 Time display: You can select system displays time or not when you playabck.  Channel display: You can select system displays channel number or not when

you playback.  Snapshoot: Click snapshoot button, you can see an interface is shown as in

Figure 5-8.(This function applies to some series only)

 Mode: There are two types: one is timing and the other is activation (trigger).  Image size: D1/HD1/BCIF/CIF.  Image quality: level1 to level 6.  Snapshoot frequency: Here you can set the snapshoot frequency. The value

ranges from 1s/p to 7s/p. System default setup is:

 Channel:1  Compression:H.264  Resolution: CIF/D1

 Bit rate: CBR  Quality: 4  Frame rate: 25f/s

Please highlight icon to select the corresponding function.

Figure 5-6

Figure 5-7

Figure 5-8

For RG-S series, it supports various settings for channel, resolution and frame: Resolution：pixel PAL：QCIF=176×144; CIF＝352×288; HD1＝352×576; 2CIF=704×288; D1

＝704×576;

NTSC：QCIF=176×120; CIF＝352×240; HD1＝352×480; 2CIF=704×288;

D1＝704×480; We take 16-channel DVR as an example. There are four groups：1~4, 5~8, 9~12, 13~16. Please refer to the formula：resolution× frame rate The resources for one group are: PAL: D1×50 or NTSC: D1×60 D1×50(60)F/s=Half-D1×100(120)F/s=CIF×200(240)F/s You can arrange channel parameter within the specified limit. Please refer to the following list：

Channel resources A B C D

Max frame PAL（NTSC）

Note

D1 25(30)F/s

D1 12(15)F/s

D1 6(7)F/s

25(30)F/s 1 D1 real-

time, 3

D1 non-

real time

D1 12(15)F/s

12(15)F/s 4 D1non-

real time

D1 25(30)F/s

HD1 25(30)F/s

CIF 25(30)F/s

25(30)F/s 1 D1,1 HD1,2

CIF

real-time HD1 25(30)F/s

HD1 25(30)F/s

25(30)F/s 4 HD1 real-time

CIF 25(30)F/s

25(30)F/s 4 CIF real-time

… … … … … Other setup Note：

 A、B、C、D is the four channels in one group.  The totally whole resources are limited. When you wan to enhance resource in

one channel you need to reduce resource for other channel.

 The system will pop up setup failure interface if the resource setup is beyond the

limit. In the above list, × means there is no video in current channel. You can highlight “video” button to activate video function. Dual encoding streams: this series support dual encoding streams. Main stream is for local recording, and the extra stream can be used for network transmission. And they don’t affect each other. So for local recording you can use main stream. And for network transmission, you can select main stream or extra stream.

5.3.3 Schedule

Please refer to chapter 4.4 schedule.

5.3.4 RS232

RS232 interface is shown as below. Here are five items. See Figure 5-9.  Function: There are various devices for you to select. Console is for serial port or

min-end platform to upgrade program. Keyboard is for you to use special

keyboard to control current device.

 Baud rate: You can select proper baud rate.  Data bit: You can select proper data bit.  Stop bit: There are three values: 1/1.5/2.

 Parity: there are three choices: none/odd/even. After completing all the setups please click save button, system goes back to the previous menu.

Figure 5-9

5.3.5 Network

Here is for you to input network information. See Figure 5-10.

 IP address: Here you can input IP address.  DHCP: It is auto search IP function. When enable DHCP function, you can not

modify IP/Subnet mask /Gateway. These values are from DHCP function. If you

have not enabled DHCP function, IP/Subnet mask/Gateway display as o. You

need to disable DHCP function to view current IP information. Besides, when

PPPoE is operating, you can not modify IP/Subnet mask /Gateway.  TCP port: Default value is 37777. (System server port 37778 is reserved for

network UDP use.)

 UDP port: Default value is 37778.  HTTP port: Default value is 80.  Max connection: system support maximal 10 users. 0 means there is no

connection limit.

 Transfer mode: Here you can select the priority between fluency/video qualities.  Network download: System can process the downloaded data first if you enable

this function. After completing all the setups please click save button, system goes back to the previous menu.

Figure 5-10

5.3.5.1 Advanced Setup Advanced setup interface is shown as in Figure 5-11. Please draw a circle to enable corresponding function and then double click current item to go to setup interface.

Figure 5-11

5.3.5.2 IP Filter IP filter interface is shown as in Figure 5-12. You can add IP in the following list. The list supports max 64 IP addresses. Please note after you enabled this function, only the IP listed below can access current DVR. If you disable this function, all IP addresses can access current DVR.

Figure 5-12

5.3.5.3 Multiple Cast Setup Multiple-cast setup interface is shown as in Figure 5-13.

Figure 5-13

Here you can set a multiple cast group. Please refer to the following sheet for detailed information.  IP multiple cast group address

-224.0.0.0-239.255.255.255

-“D” address space

 The higher four-bit of the first byte=”1110”

 Reserved local multiple cast group address

-224.0.0.0-224.0.0.255

-TTL=1 When sending out telegraph

-For example

224.0.0.1 All systems in the sub-net

224.0.0.2 All routers in the sub-net

224.0.0.4 DVMRP router

224.0.0.5 OSPF router

224.0.0.13 PIMv2 router  Administrative scoped addressees

-239.0.0.0-239.255.255.255

-Private address space

 Like the single broadcast address of RFC1918  Can not be used in Internet transmission  Used for multiple cast broadcast in limited space.

Except the above mentioned addresses of special meaning, you can use other addresses. For example: Multiple cast IP: 235.8.8.36 Multiple cast PORT: 3666.

5.3.5.4 PPPoE PPPoE interface is shown as in Figure 5-14. Input “PPPoE name” and “PPPoE password” you get from your ISP (Internet service provider). Click save button, you need to restart to activate your configuration. After rebooting, IP camera will connect to internet automatically. The IP in the PPPoE is the DVR dynamic value. You can access this IP to visit the unit.

Figure 5-14

5.3.5.5 NTP Setup You need to install SNTP server (Such as Absolute Time Server) in your PC first. In Windows XP OS, you can use command “net start w32time” to boot up NTP service. NTP setup interface is shown as in Figure 5-15.

 Host IP: Input your PC address.  Port: This series DVR supports TCP transmission only. Port default value is 123.  Update interval: minimum value is 15(Unit: minute)  Time zone: select your corresponding time zone here.

Here is a sheet for your time zone setup.

City /Region Name Time Zone

London GMT+0 Berlin GMT+1 Cairo GMT+2 Moscow GMT+3 New Deli GMT+5 Bangkok GMT+7 Beijing (Hong Kong) GMT+8 Tokyo GMT+9 Sydney GMT+10 Hawaii GMT-10 Alaska GMT-9 Pacific Time(P.T) GMT-8

American Mountain Time(M.T) GMT-7 American Central Time(C.T) GMT-6 American Eastern Time(E.T) GMT-5 Atlantic Time GMT-4 Brazil GMT-3 Middle Atlantic Time GMT-2

Figure 5-15

5.3.5.6 Email Setup Email setup interface is shown as in Figure 5-16. Here you can set email server information.

Note:

You need to get the email address from your email service provider first. Please use semicolon to separate the addresses.

Figure 5-16

5.3.5.7 DDNS Setup DDNS setup interface is shown as in Figure 5-17. You need a PC of fixed IP in the internet and there is the DDNS software running in this PC. In other words, this PC is a DNS (domain name server). In network DDNS, input your PPPoE name you get from you IPS and server IP (PC with DDNS ) . Click save button and then reboot system. Click save button, system prompts for rebooting to get all setup activated. After rebooting, open IE and input as below: http

：//(DDNS server IP)/(virtual directory name)/webtest.htm e.g.: http：//10.6.2.85/DVR _DDNS/webtest.htm.) Now you can open DDNSServer web search page.

Figure 5-17

5.3.5.8 Alarm Server You can set alarm in accordance with different alarm protocols. System can inform the alarm server when alarm occurs. See Figure 5-18.

Figure 5-18

5.3.5.9 FTP You need to download or buy FTP service tool (such as Ser-U FTP SERVER) to establish FTP service. Please install Ser-U FTP SERVER first. From “start” -> “program” -> Serv-U FTP Server -> Serv-U Administator. Now you can set user password and FTP folder. Please note you need to grant write right to FTP upload user. See Figure 5-19.

Figure 5-19

You can use a PC or FTP login tool to test setup is right or not. For example, you can login user ZHY to FTP://10.10.7.7 and then test it can modify or delete folder or not. See Figure 5-20.

Figure 5-20

System also supports upload multiple DVRs to one FTP server. You can create multiple folders under this FTP. In Figure 5-10, select FTP and then double click mouse. You can see the following interface. See Figure 5-21.

Figure 5-21

Please highlight the icon in front of Enable to activate FTP function. Now FTP can upload alarm video and motion detection video. Please note, when

you are using this function, please make sure current upload channel is in motion detection or alarm record status and there is video available. Here you can input FTP server address, port and etc.

Figure 5-22

 File length: upload file length. When setup is larger than the actual file length,

system will upload the whole file. When setup here is smaller than the actual file length, system only uploads the set length and auto ignore the left section.

 When interval value is 0, system uploads all corresponding files.  Period 1 and period 2: you can set two periods for one each channel.

System file name is shown as in Figure 5-23.

Figure 5-23

5.3.6 Alarm

Please refer to chapter 4.6 Alarm Setup and Activation.

5.3.7 Detect

Please refer to chapter 4.5 Detect.

5.3.8 Pan/Tilt/Zoom

The pan/tilt/zoom setup includes the following items. Please select channel first. See Figure 5-24.

 Protocol: select corresponding PTZ protocol such as PELCOD.  Address: input corresponding PTZ address.  Baud rate: select baud rate.  Data bit: select data bit.  Stop bit: select stop bit.  Parity: there are three choices: none/odd/even.

After completing all the setups please click save button, system goes back to the previous menu. For detailed setup, please refer to chapter 4.9 preset/patrol/pattern/scan.

Figure 5-24

5.3.9 Display

Display setup interface is shown as below. See Figure 5-25.  Transparency: Here is for you to adjust transparency. The value ranges from 128

to 255.

 Channel name: Here is for you to modify channel name. Please note all your

modification here only applies to DVR local end. You need to open web or client end to refresh channel name.

 Time display: You can select to display time or not when system is playback.  Channel display: You can select to channel name or not when system is

playback.

 Overlay information: System displays some information in the screen for your

reference.

 Display mode: you can select from the dropdown list: self-adaptive/VGA/TV.  Enable tour: activate tour function.  Interval: Input proper interval value here. The value ranges from 5-200 seconds.

In tour process, you can use mouse or click Shift to turn on window switch function. Stands for opening switch function, stands for closing switch

function.

 Motion tour type: System support 1/8 window tour.  Alarm tour type: System support 1/8 window tour.

Please highlight icon to select the corresponding function. After completing all the setups please click save button, system goes back to the

previous menu.

Figure 5-25

In Figure 5-25, click modify button after channel. You can see an interface is shown as in Figure 5-26. Please note all your modification here applies to local end only. You need to refresh web or client-end to get the latest channel name. System max support 25-digital character.

Figure 5-26

In tour mode, you can see the following interface. On the right corner, right click mouse or click shift button, you can control the tour. There are two icons: stands for enabling window switch and stands for enabling window function. See Figure 5-27.

Figure 5-27

5.3.10 Default

Click default icon, system pops up a dialogue box. You can highlight to restore default factory setup. See Figure 5-28.

 Select all  General  Encode  Schedule  RS232  Network  Alarm  Detect  Pan/tilt/zoom  Display  Channel name

Please highlight icon to select the corresponding function. After all the setups please click save button, system goes back to the previous menu.

Warning!

System menu color, language, time display mode, video format, IP address, user account will not maintain previous setup after default operation!

Figure 5-28

5.4

5.45.4

5.4 Search

Search Search

Please refer to chapter 4.3 Search.

5.5

5.55.5

5.5 Advanced

Advanced Advanced

Advanced

Double click advanced icon in the main window, the interface is shown as below. See Figure 5-29. There are total seven function keys: HDD management, alarm output, abnormity, manual record, account, auto maintain, and TV adjust.

Figure 5-29

5.5.1 HDD Management

Here is for you to view and implement hard disk management. See Figure 5-30. You can set proper mode for each hard disk from the dropdown list. When you use redundant backup function, you can set one or more redundant HDD(s). Please note you need to set at least one read-write disk, otherwise system will not record video. For detailed information you can refer to chapter 4.4 Schedule. After all the setups please click save button, system needs to reboot to get all the modification activated.

Figure 5-30

Click alarm set button, the interface is shown as below. See Figure 5-31(This interface is just like the abnormity setup).

Please highlight icon to select the corresponding function. You can enable one or more alarm setups. The lower limit ranges from 1% to 99%.

Alarm channel number ranges from 1 to 6. Delay value is from 0 to 240 seconds. Please note when HDD capacity is not full system only alarms once! After all the setups please click OK button, system goes back to the previous menu

Figure 5-31

5.5.2 Abnormity

Abnormity interface is shown as in Figure 5-32.  Event type: There are several options for you such as disk error, no disk and

etc.

 Alarm output: alarm activation output port (multiple choices), among which is

controllable 12V output.

 Latch: here you can set corresponding delaying time. The value ranges from 10s-

300s. System automatically delays specified seconds in turning off alarm and activated output after external alarm cancelled.

 Show message: system can pop up the message in the local screen to alert

you when alarm occurs.

 Send email: System can send out email to alert you when alarm occurs.

Figure 5-32

5.5.3 Alarm Output

Here is for you to set proper alarm output.

Please highlight icon to select the corresponding alarm output. After all the setups please click OK button, system goes back to the previous menu.

See Figure 5-33.

Figure 5-33

5.5.4 Manual Record

Please refer to chapter 4.2.2 manual record.

5.5.5 Account

Here is for you to implement account management. See Figure 5-34. Here you can:

 Add new user  Modify user  Add group

 Modify group  Modify password.

For account management please note:  System account adopts two-level management: group and user. No limit to group

or user amount.

 For group or user management, there are two levels: admin and user.  The user name and group name can consist of eight bytes. One name can only

be used once. There are four default users: admin/888888/666666 and hidden user “default”. Except user 6666, other users have administrator right.

 Hidden user “default” is for system interior use only and can not be deleted.

When there is no login user, hidden user “default” automatically login. You can set some rights such as monitor for this user so that you can view some channel view without login.

 One user should belong to one group. User right can not exceed group right.  About reusable function: this function allows multiple users use the same

account to login.

After all the setups please click save button, system goes back to the previous menu.

Figure 5-34

5.5.6 Auto Maintain

Here you can set auto-reboot time and auto-delete old files setup. See Figure 5-35. You can select proper setup from dropdown list. After all the setups please click save button, system goes back to the previous menu.

Figure 5-35

5.5.7 TV Adjust

Here is for you to adjust TV output setup. See Figure 5-36. Please drag slide bar to adjust each item. After all the setups please click OK button, system goes back to the previous menu.

Figure 5-36

5.5.8 Video Matrix (For RGH--S and RGL-S Series only)

Some series DVR have the matrix and loop outputs.

5.5.8.1 Loop outputs They are just the same with video distributors. There are 4/8/16-ch video loop outputs from our DVR. The DVR video output can connect with other devices such as TV walls, analog matrix and so on.

5.5.8.2 Matrix outputs They are like the small-scale matrix. You can select any camera from our DVR to switch. And the output can also tour between the cameras. So the matrix outputs can be used to build TV walls and tour and display the cameras one by one.

5.5.8.3 Rear Panel Connection The rear panel is shown as below. See Figure 5-37.

Figure 5-37

5.5.8.4 37-pin cable introduction There are three colors cable. See Figure 5-38.

 Black: for loop outputs, there are 16-ch loop outputs  Blue: for matrix outputs, there are 4-ch matrix outputs  White: for bi-direction talk, one is for audio in and the other is for audio out.

Figure 5-38

5.5.8.5 Matrix setup

5.5.8.5.1 Enter Video Matrix Interface In the menu, from “Advanced” to “Video Matrix”. You can see an interface is shown as in Figure 5-39.

Figure 5-39

5.5.8.5.2

Right Mouse Menu In one-window display mode, right click mouse to select “Video Matrix”. See Figure 5-40.

Figure 5-40

5.5.8.6 Video Matrix Interface and Application The video matrix interface is shown as in Figure 5-41.

Now MGxxL series support 4-channel matrix outputs and MGxxH series support 1 channel matrix output. All the operation below based on MG series DVR.

You can set for each channel. The function consists of three types. The priority is: alarm>motion detection>schedule.

5.5.8.6.1 Scheduled Video Output (Scheduled Tour)

Please enable corresponding video output item and input tour interval, and then set the tour output channel. System maximally supports 16 channels. Now system can implement tour output as you just set.

Figure 5-41

5.5.8.6.2 Alarm Activation Matrix

Please go to alarm setup interface to set the alarm activate matrix function ((Main Menu->Setting->Alarm)). See Figure 5-42. You can follow the steps listed below:

 Select local alarm  The record channel function has been enabled and you have selected

corresponding record channel.

 The video matrix function has been enabled and you have selected

corresponding video matrix channel. After selecting activation channel in the record channel item, you can enable video matrix function and then select vide output channel. Once the alarm occurs, system continues scheduled matrix tour after alarm tour completes. If there is no scheduled tour available, the matrix will stop at the last activation channel after alarm completes.

When there are several alarm inputs at the same time, the situation maybe a little bit complex. Here is an example. System setup is shown as below:  Alarm input 1 can activate channel1/2/3/4/5/6

Highlighted

here

Select ALL or cancel

Select channel(s)

here

Input interval here

 Alarm input 2 can activate channel 2/3/4/5/6/7/8  Alarm input 1 and alarm input 2 activate video output 1.

So, when there is alarm from channel 1, video output 1 becomes valid. If there is no alarm from alarm input 2 during the same period, then video output 1 can tour between channel1/2/3/4/5/6. When video output 1 goes to channel 3 and there is alarm form channel2, then video output 1 tour between 4/5/6/7/8/2. The general principles are:  When alarm activate, each valid channel alarm input can activate a complete

tour between activation channels.  When there are several alarm inputs in the same video matrix output, system

video matrix can activate all the channels in the setup.  If system has toured some activation channels, then corresponding alarm

activation channels are null.

Figure 5-42

5.5.8.6.3 Motion Detection (including video loss and camera masking)

Motion detection principle is the same as alarm. You can set in motion detection interface (Main menu->Setting->Detect). See Figure 5-43. In detect interface, you can set the activation channel. You can enable video matrix function if you want to set matrix function, and then set video matrix output channel. Once the activation occurs, system continues scheduled matrix tour after motion detection tour completes. If there is no scheduled tour available, the matrix will stop at the last activation channel after alarm completes

Select alarm input channel

Highlighted here

Corresponding to video out put in

Figure 5-41.

Figure 5-43

5.5.8.6.4 General Tour Principle

When system is in scheduled tout status, once the alarm occurs, system first check video matrix function has been enabled or not and there is effective matrix or not. System will continue implementing scheduled tour in the following two conditions:

 Video output function has not been enabled.  There is no video matrix setup available.

If there is valid video matrix setup, system can activate corresponding tour among alarm channels and then begin scheduled tour after alarm tour completes. If there is no schedule tour available, the matrix will stop at the last activation channel after alarm completes.

Motion detection activation is almost the same as the alarm. But it has different priority. System will continue implementing scheduled tour in the following two conditions:

 Video output function has not been enabled.  There is no video matrix setup available.

If there is a valid video matrix setup, system will check weather there is tour of higher priority and implement corresponding process. During the motion detection tour, system will process alarm first if alarm occurs. It is the same as alarm occurs in scheduled tour period.

5.6

5.65.6

5.6 Information

Information Information

Information

Here is for you to view system information. There are total five items: HDD (hard disk information), BPS (data stream statistics), Log and version, and online user. See Figure 5-44.

Figure 5-44

5.6.1 HDD Information

Here is to list hard disk type, total space, free space, video start time and status. See Figure 5-45.

Note:

Please remove the broken hard disk before you add a new one. Once there is a hard disk confliction, please check hard disk time and system time is the same or not. Please go to setting then general to modify system time. At last, reboot the system to solve this problem.

If disk is damaged, system shows as “?”

Figure 5-45

5.6.2 BPS

Here is for you to view current video data stream (KB/s) and occupied hard disk storage (MB/h). See Figure 5-46.

Figure 5-46

5.6.3 Log

Here is for you to view system log file. System lists the following information. See Figure 5-47. Log types include system operation, configuration operation, data management, alarm event, record operation, log clear and etc. Pleased select start time and end time, then click search button. You can view the log files. Please page up/down button to view if there are more than ten files.

Figure 5-47

5.6.4 Version

Here is for you to view some version information. See Figure 5-48.

 Channel  Alarm in  Alarm out  System version:  Build Date

Figure 5-48

5.6.5 Online Users

Here is for you manage online users. See Figure 5-49. You can disconnect one user or block one user if you have proper system right.

Figure 5-49

5.7

5.75.7

5.7 Exit

ExitExit

Exit

Double click exit button, system pop up a dialogue box for you to select. See Figure 5-50.  Logout menu user: log out menu. You need to input password when you login

the next time.

 Restart application: reboot DVR.  Shutdown: system shuts down and turns off power.  Restart system: system begins rebooting.  Switch user: you can use another account to log in.

Figure 5-50

6 About

About About

About AAAAuxiliary

uxiliary uxiliary

uxiliary MMMMenu

enu enu

enu

6.1

6.16.1

6.1 Go

Go Go

Go to Pan

to Panto Pan

to Pan/Tilt/Zoom Menu

/Tilt/Zoom Menu/Tilt/Zoom Menu

/Tilt/Zoom Menu

In the one-window surveillance mode, right click mouse (click “fn” Button in the front panel or click AUX key in the remote control). The interface is shown as below: See Figure 6-1.

Figure 6-1 Click Pan/Tilt/Zoom, the interface is shown as in Figure 6-2. Here you can set the following items:

 Zoom  Focus  Iris

Click icon and to adjust zoom, focus and Iris.

Figure 6-2 In Figure 6-2, please click direction arrows (See Figure 6-3 ) to adjust PTZ position. There are totally eight direction arrows. (Please note there are only four direction arrows in DVR front panel.)

Figure 6-3

6.1.1 3D Intelligent Positioning Key

In the middle of the eight direction arrows, there is a 3D intelligent positioning key. See Figure 6-4 . Click this button, system goes back to the single screen mode. Drag the mouse in the screen to adjust section size.

Figure 6-4

Here is a sheet for you reference.

Name Function

key

function Shortcut

key

Function key

function Shortcut

key

Zoom

Near ►

Far



Focus

Near 

Far ►

Iris

close ⊳

Open 

6.2

6.26.2

6.2 Preset

Preset Preset

Preset ////PPPPatrol

atrol atrol

atrol //// PPPPattern

attern attern

attern /Bo

/Bo/Bo

/Border

rder rder

rder FFFFunction

unction unction

unction

In Figure 6-2 click the set button. The interface is shown as below: Here you can set the following items:

 Preset  Patrol  Pattern  Border

Figure 6-5 In Figure 6-2, click page switch button, you can see an interface as in Figure 6-6. Here you can activate the following functions:

 Preset  Tour(Patrol)  Pattern  Auto scan  Auto pan  Flip  Page Switch

Figure 6-6

6.2.1 Preset Setup Note: The following setups are usually operated in the Figure 6-2, Figure 6-5 and

Figure 6-6. In Figure 6-2, use eight direction arrows to adjust camera to the proper position. In Figure 6-5, click preset button and input preset number. The interface is shown as in Figure 6-7. Add this preset to one patrol number

Figure 6-7

6.2.2 Activate Preset

In Figure 6-6 please input preset number in the No. blank, and click preset button.

6.2.3 Patrol Setup

In Figure 6-5, click patrol button. The interface is shown as in Figure 6-8. Input preset number and then add this preset to one patrol.

Figure 6-8

6.2.4 Activate Patrol

In Figure 6-6, input patrol number in the No. blank and click patrol button

6.2.5 Pattern Setup

In Figure 6-5, click pattern button and then click begin button. The interface shows like Figure 6-9. Please go to Figure 6-2 to modify zoom, focus, and iris. Go back to Figure 6-9 and click end button. You can memorize all these setups as pattern 1.

Figure 6-9

6.2.6 Activate Pattern Function

In Figure 6-6 input mode value in the No. blank, and click pattern button.

6.2.7 Border Setup

In Figure 6-5, click border button. The interface is shown as in Figure 6-10. Please go to Figure 6-2, use direction arrows to select camera left limit, and then please go to Figure 6-10 and click left limit button Repeat the above procedures to set right limit.

Figure 6-10

6.2.8 Activate Border Function

In Figure 6-6, click auto scan button, the system begins auto scan. Correspondingly, the auto scan button changes to stop button. Click stop button to terminate scan operation.

6.2.9 Flip

In Figure 6-6, click page switch button, you can see an interface is shown as below. See Figure 6-11. Here you can set auxiliary function. Click page switch button again, system goes back to Figure 6-2.

Figure 6-11

7 W

WEB CLIENT OPERATION

EB CLIENT OPERATIONEB CLIENT OPERATION

EB CLIENT OPERATION

Please note, all the operation here is taking 16-ch DVR as an example. There might be slightly difference in the interface due to different series.

7.1

7.17.1

7.1 Network

Network Network

Network CCCConnection

onnection onnection

onnection

Before web client operation, please check the following items:

 Network connection is right  DVR and PC network setup is right. Please refer to network setup(main menu-

>setting->network)

 Use order ping ***.***.***.***(* DVR IP address) to check connection is OK or not.

Usually the return TTL value should be less than 255.

 System is compatible with WIN VISTA web control right now. But you need to

disable user account control function. Double click user account and then disable user account control. After completing setup, please reboot the PC.

 System can automatically download latest web control and the new version can

overwrite the previous one.

 If you want to un-install the web control, please run uninstall web.bat. Please

note, before you un-install, please close all web pages, otherwise the uninstallation might result in error.

7.2

7.27.2

7.2 Login

Open IE and input DVR address in the address column. For example, if your DVR IP is 10.10.3.16, then please input http:// 10.10.3.16 in IE address column. See Figure 7-1

Figure 7-1 System pops up warning information to ask you whether install webrec.cab control or

not. Please click yes button.

Input your IP

address here.

If you can’t download the ActiveX file, please modify your settings as follows. See Figure 7-2.

Figure 7-2 After installation, the interface is shown as below. See Figure 7-3.

Please input your user name and password. Default factory name is admin and password is admin. Note: For security reasons, please modify your password after you first login.

Figure 7-3

After you logged in, you can see the main window. See Figure 7-6. This main window can be divided into the following sections.  Section 1: there are five function buttons: configuration (chapter 7.3), search

(chapter 7.4), alarm (chapter 7.5), about (chapter 7.6), log out (chapter 7.7).

 Section 2: there are channel number and three function buttons: refresh, start

dialog and local play.

 Section3: there are PTZ (chapter 7.2.2), color (chapter 7.2.3) button and you can

also select picture path and record path.

 Section 4:real-time monitor window. Please note current preview window is

circled by a green rectangle zone.

 Section 5: Here you can view window switch button. You can also select video

priority between fluency or real-time.  System monitor window switch supports full screen/1-window/4-window/6-

window/8-window/9-window/13-window/16-window/20-window/25window/36-window. See Figure 7-4.

Figure 7-4

 Preview window switch. System support 1/4/8/9/16-window real-time preview.

Please you need to have the proper rights to implement preview operation. You can not preview if you have no right to preview the either channel. See Figure 7-5.

Figure 7-5

Section1

Section 2

Section 3

Section 5

Section 4

Figure 7-6

7.2.1 Real-time Monitor

In section 2, left click the channel name you want to view, you can see the corresponding video in current window. For detailed function key information, please refer to Figure 7-7.

Figure 7-7

 1: Digital zoom: Click this button and then left drag the mouse in the zone to

zoom in. right click mouse system restores original status.

 2: Change show mode: resize or switch to full screen mode.  3: Local record. When you click local record button, the system begins recording

and this button becomes highlighted. You can go to system -.local record to set video file path.

 4: Capture picture. You can snapshoot important video. All images are

memorized in system client folder \download\picture (default).

 5: Audio :Turn on or off audio.(It has no relationship with system audio setup )  6: Close video.

Please refer to Figure 7-8 for main stream and extra stream switch information.

Figure 7-8

Refresh

You can use button to refresh camera list.

Start Dialogue

You can click this button to enable audio talk.

Local Play

1 2 3 4 5 6

Click local play button, system pops up the following interface for you to select local play file. See Figure 7-9.

Figure 7-9

7.2.2 PTZ

Before PTZ operation, please make sure you have properly set PTZ protocol. (Please refer to chapter 7.3.2 Setting-> Pan/Tilt/Zoom). Click PTZ button, the interface is shown as in Figure 7-10 .

Figure 7-10

7.2.2.1 Direction key and 3D positioning key In Figure 7-10, there are eight direction keys. In the middle of the eight direction keys, there is a 3D intelligent positioning key. Click SIT button, system goes back to the single screen mode. Drag the mouse in the screen to adjust section size. It can realize PTZ automatically.

7.2.2.2 Speed System supports eight-level speed. You can select from the dropdown list. Speed 2 is faster than speed 1.

You can click this icon to display or hide the PTZ control platform.

7.2.2.3 Zoom/Focus/Iris Here is a sheet for you reference.

Name Function

key

Function Function

key

Function

Zoom

Near

Far

Focus

Near

Far

Iris

Open

Then click triangle icon in Figure 7-10, you can see the following interface. See Figure 7-11.

Figure 7-11

In Figure 7-11, click PTZ setup button you can see the following interface. See Figure 7-12.

Figure 7-12

7.2.2.4 Auto Scan In Figure 7-12, move the camera to you desired location and then click left limit button. Then move the camera again and then click right limit button to set a right limit.

7.2.2.5 Pattern In Figure 7-12, you can input pattern value and then click start record button to begin PTZ movement. Please go back to Figure 7-11 to implement camera operation. Then you can click stop record button. Now you have set one pattern.

7.2.2.6 Preset In Figure 7-12, move the camera to your desired location and then input preset value. Click add button, you have set one preset.

7.2.2.7 Auto tour In Figure 7-12, input auto tour value and preset value. Click add button, you have added one preset in the tour. Repeat the above procedures you can add more presets in one tour.

7.2.2.8 Assistant You can select the assistant item from the dropdown list. See Figure 7-13.

Figure 7-13

7.2.3 Color

Click color button in section 3, the interface is shown as Figure 7-14. Here you can select one channel and then adjust its brightness, contrast, hue and saturation. (Current channel border becomes green). Or you can click default button to use system default setup.

Figure 7-14

7.2.4 Picture Path and Record Path

Click more button in Figure 7-14, you can see an interface is shown as in Figure 7-15.

Figure 7-15

Click picture path button, you can see an interface is shown as in Figure 7-16.

Figure 7-16

Click record path button, you can see an interface is shown as in Figure 7-17.

Figure 7-17

7.2.5 Menu Interface Switch

Put your mouse on the PTZ control bar until you see the following icon. See Figure 7-18.

Figure 7-18

Left click your mouse and then drag it to the channel control status bar. You can see the two menus interface switched. See Figure 7-19. You can compare the following interface with Figure 7-6.

Figure 7-19

7.3

7.37.3

7.3 Configure

ConfigureConfigure

Configure

In the main window, click config button, you can see an interface is shown as in Figure 7-20.

Figure 7-20

7.3.1 System Information

Click device configuration button, you can see the following interface. See Figure 7-21.

100

Figure 7-21

 Version Click version button, you can see corresponding HDD information for your reference. See Figure 7-22.

Figure 7-22

Protex PRX-MG04 Series, PRX-MG08 Series, PRX-MG16 Series User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual