Protech Systems PPC-7365F User Manual

USER’S
MANUAL

PPC-7365F

VIA Eden Low Power
15” Panel PC System

PPC-7365F M1

Copyright Notice

PPC-7365F Panel PC System

With LCD / Touch screen

OPERATION MANUAL

COPYRIGHT NOTICE

This operation manual is meant to assist users in installing and setting up the
system. The information contained in this document is subject to change
without prior any notice.

This manual is copyrighted August, 2005. You may not reproduce or
transmit in any form or by any means, electronic, or mechanical, including
photocopying and recording.

ACKNOWLEDGEMENTS

All trademarks and registered trademarks mentioned herein are the property
of their respective owners.

CE NOTICE

This is a class A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate
measures.

Copyright Notice

FCC NOTICE

This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at his own expense.

You are cautioned that any change or modifications to the equipment not
expressly approve by the party responsible for compliance could void your
authority to operate such equipment.

* All information contained in this document is subject to change without prior notice.

CAUTION! Danger of explosion if battery is incorrectly replaced. Replace only with the
same or equivalent type recommended by the manufacturer. Dispose of used batteries
according to the manufacturer’s instructions.
WARNING! Some internal parts of the system may have high electrical voltage. And
therefore we strongly recommend that qualified engineers can open and disassemble the
system.
The LCD and touch screen are fragile, please handle them with extra care.

Contents

TABLE OF CONTENTS

CHAPTER 1 INTRODUCTION

1-1 About This Manual ....................................................... 1-2

1-2 Case Illustration ............................................................. 1-3

1-3 System Specification ..................................................... 1-5

1-4 Safety and Notification ................................................... 1-10

CHAPTER 2 SYSTEM CONFIGURATION

2-1 Jumper & Connector Quick Reference Table ............... 2-2

2-2 Component Locations ................................................... 2-3

2-3 How to Set the Jumpers ................................................ 2-4

2-4 COM Port Connector ………………………………… 2-6
2-5 COM Port RI & Voltage Selection ……………….….. 2-8
2-6 RS232/422/485 (COM2) Selection …………..….…… 2-10
2-7 VGA Connector ……………………………………….. 2-11
2-8 LVDS Connector ……………………………………… 2-12
2-9 Brightness Voltage Selection …………………………. 2-13
2-10 LVDS Voltage Selection ………………………….…… 2-14
2-11 Power Connector ………………………………………. 2-15
2-12 Floppy Disk Drive Connector ………………………… 2-16
2-13 Hard Disk Drive Connector ………..…………………. 2-17
2-14 Printer Connector ……………………………………… 2-18
2-15 LAN Connector ………………….……………………. 2-19
2-16 LAN LED Connector …...…………………………….. 2-19
2-17 Keyboard Connector ………………………………….. 2-20
2-18 PS/2 Mouse Connector ………………………………… 2-20
2-19 Sound Connector ………………………………………. 2-21
2-20 Onboard Audio Selection …………………………….. 2-22
2-21 Reset Connector ………………………………………. 2-22
2-22 HDD LED Connector ………………………………….. 2-22

2-23 Power Button ………………….…................................ 2-23

2-24 External Speaker Connector …………………………… 2-23
2-25 External SMI Connector ………………………………. 2-23
2-26 Clear CMOS Selection ………………………………… 2-24
2-27 Universal Serial Bus Connector ………………………. 2-25
2-28 Reset/NMI Selection ………………………..………… 2-26
2-29 Wake-On-LAN Connector …………………………….. 2-27
2-30 Power LED Connector ………………………………… 2-27

Contents

2-31 Memory Installation ............……….............................. 2-27

2-32 AT/ATX Power Selection ……………………………. 2-28
2-33 Compact Flash Master/Slave Selection ………………. 2-29
2-34 IRQ12 Release Selection ……………………………… 2-29
2-35 LVDS Panel Resolution Selection ……………………. 2-30
2-36 Inverter Connector …………………………………… 2-30
2-37 Power Module ………………………………..………. 2-31
2-38 Compact Flash Connector …………………………….. 2-32
2-39 PC 104 Connector …………………………………….. 2-33
2-40 PC 104+ Connector ……………………………………. 2-34
2-41 CPU Fan Connector …………………………………… 2-35
2-42 System Fan Connector ………………………………… 2-35

CHAPTER 3 SOFTWARE UTILITIES

3-1 Introduction ................................................................... 3-2

3-2 VIA 4 In 1 Service Pack Driver ………………………. 3-2

3-3 VGA Driver Utility ....................................................... 3-3

3-4 Flash BIOS Update ....................................................... 3-4

3-5 LAN Driver Utility ........................................................ 3-6

3-6 Sound Driver Utility .............................…..................... 3-7

3-7 USB2.0 Chipset Software Installation Utility …………. 3-8
3-8 Touch Screen Driver Utility (Optional) ………..…….. 3-9
3-9 USB CF Card Driver Utility (Optional) ……………… 3-9

3-10 Watchdog Timer Configuration .................................... 3-9

CHAPTER 4 AWARD BIOS SETUP

4-1 Introduction ................................................................... 4-2

4-2 Entering Setup ............................................................... 4-3

4-3 The Standard CMOS Features ….................................. 4-4

4-4 The Advance BIOS Features ….................................... 4-8

4-5 The Advanced Chipset Features ................................... 4-11

4-6 Integrated Peripherals ……........................................... 4-14

4-7 Power Management Setup ……………………………. 4-18

4-8 PNP/PCI Configuration ................................................ 4-20

4-9 PC Health Status …………………………………….. 4-22
4-10 Frequency / Voltage Control ………………………… 4-24

4-11 Load Fail-Safe Defaults ................................................ 4-25

4-12 Load Optimized Defaults .............................................. 4-25

Contents

4-13 Password Setting .................................................…...... 4-26

4-14 Save & Exit Setup ......................................................... 4-27

4-15 Exit Without Saving ...................................................... 4-28

APPENDIX A SYSTEM ASSEMBLY

Exploded Diagram for HDD Assembly ….…………………… A-2
Exploded Diagram for Wall Mounting ….……….…………… A-3
Exploded Diagram for VESA ARM ……..……..…………..… A-7

APPENDIX B TECHNICAL SUMMARY

Block Diagram ......................................................................... B-2

Interrupt Map ........................................................................... B-3

RTC & CMOS RAM Map ....................................................... B-4

Timer & DMA Channels Map .................................................. B-5

I/O & Memory Map ................................................................. B-6

Page:1-1

INTRODUCTION

This chapter gives you the information for PPC-7365F. It also
outlines the System specifications.

Section includes:

z About This Manual

z Case Illustration

z System Specifications

z Safety precautions

Experienced users can skip to chapter 2 on page 2-1
for a Quick Start.

CHAPTER

1

Chapter 1 Introduction

Page: 1-2

PPC-7365F USER

′

S MANUAL

1-1. ABOUT THIS MANUAL

Thank you for purchasing our Panel PC. It is an updated system designed to be

comparable with the highest performance of IBM AT personal computers. It
provides faster processing speed, greater expandability, and can hand le more
tasks. This manual is designed to assist you on how to make the proper
installation to set up the system. It contains five chapters. The user can use
this manual for configuration according to the following chapters :

Chapter 1 Introduction

This chapter introduces you to the background of this manual, illustration of
the case, and the specifications for this system. The final page of this chapter
indicates some safety reminders on how to take care of your system.

Chapter 2 System Configuration

This chapter outlines the Prox-7360 components' locations and their functions.
In the end of this chapter, you will learn how to set jumper and how to
configure the system for your own needs.

Chapter 3 Software Utilities

This chapter contains helpful information for proper installations of the VGA
utility, LAN utility, Sound utility and Flash BIOS update. It also describes
the function of the Watchdog Timer.

Chapter 4 Award BIOS Setup

This chapter indicates on how to set up the BIOS configurations.

Appendix A System Assembly

This section gives you the exploded diagram for the whole system unit.

Appendix B Technical Summary

This section gives you the information about the Technical maps.

Chapter 1 Introduction

PPC-7365F USER′S MANUAL

Page: 1-3

1-2. CASE ILLUSTRATION

Chapter 1 Introduction

Page: 1-4

PPC-7365F USER

′

S MANUAL

1-3. SYSTEM SPECIFICATIONS

MAINBOARD (PROX-7360)

z CPU TYPE:

VIA Eden 733M processors
Auto detect voltage regulator.

z CHIPSET:

VIA VT8606+

VT82C686B

z MEMORY :

Up to 512 SDRAM
One 184-pin DIMM sockets on board.

z CACHE :

Built-in CPU(128/256KB Cache).

z REAL-TIME CLOCK :

CR2023 battery backed CMOS RAM
Hardware implementation to indicate century rollover.

z BIOS :

Phoenix-Award Flash BIOS for plug & play function.
Memory size with 2MB and with VGA BIOS.
Support S I/O Setup.

z KEYBOARD CONNECTOR :

Mini DIN connector.
Supports PC/AT Keyboard.

z MOUSE CONNECTOR :

Mini DIN connector.
Supports PS/2 Mouse.

Chapter 1 Introduction

PPC-7365F USER′S MANUAL

Page: 1-5

z VGA :

Integrated in VT8606, supports CRT & TFT-LCD panels. HRS DF13­20DP-1.25V (20 pin) 2 x connector on board for LVDS connection, 16-Pin
box-header on board for CRT connection. A 5-Pin box-header on board
provides the power of inverter. AVR (“RVRK11K1130206” ) is used to
control the brightness of LCD panel.

z WATCHDOG :

I / O port 443H to Enable watchdog.
I / O port 441H to Disable watchdog.
Selectable for NMI or Reset function.
Time-out timing select 0 / 8 / 16 / 24 / 32 / 40 / 48 / 56 / 64 / 72 / 80 / 88 /
96 / 104 / 112 / 120 sec +/- 25%.

z IDE INTERFACE :

1 EIDE(UDMA-33) onboard. 1 Compact Flash Type-II onboard.

z FLOPPY DISK DRIVE INTERFACE :

One 26-pin connector.
Support for slim Floppy Disk Drive.

z SERIAL PORT :

Four high speed 16550 Compatible UARTs with Send / Receive 16 Byte
FIFOs.

COM1 (D-Sub Connector) for RS-232;
COM2 (D-Sub Connector) for RS-232/422/485;
COM3 (D-Sub Connector) for RS-232
COM4 (D-Sub Connector) for RS-232.

COM1 contain 5V or 12V power capability with 9-pin D-sub connector on
rear panel. COM2/3/4 support 5V power only.

z PARALLEL PORT :

One 25-pin D-Sub connector on rear panel.
Support for SPP, ECP, EPP Function.
Bi-directional parallel port.

Chapter 1 Introduction

Page: 1-6

PPC-7365F USER

′

S MANUAL

z LAN ADAPTER :

Realtek RTL8110S Chip.
RJ-45 jack onboard, Support for 10/100/1000 Base-T Ethernet.
Support Wake-On-LAN function.

z USB CONNECTOR :

2 USB ports on rear panel, 2 internal USB ports on board. Internal USB
ports use 2.0 pitch box-header for connection. All USB ports support USB

1.1 standard.

z SOUND :

VT1612A. AC’ 97 Codec. MIC-in & SPK-out jacks on rear panel. Another
internal box-header (2.0 pitch) supports an internal speaker.

z HARDWARE MONITORING FUNCTION :

Monitor CPU Voltage, CPU Temperature.

z LED INDICATOR :

Power LED.
HDD LED.

LCD PANEL

TFT color LCD is manufactured by using very high brightness technology.
Some sequential pixels may not light or may light always, but this is not a
failure.

z LCD TYPE :

LCD Panel15”: Priority source -

LVDS

or similar model.

z PIXEL PITCH :

According to the supplier’s LCD specification.

z BRIGHTNESS :

According to the supplier’s LCD specification.

Chapter 1 Introduction

PPC-7365F USER′S MANUAL

Page: 1-7

z CONTRAST RATIO :

According to the supplier’s LCD specification.

z POWER CONSUMPTION :

According to the supplier’s LCD specification.

z VIEWING ANGLE :

According to the supplier’s LCD specification.

z RESPONSE TIME :

According to the supplier’s LCD specification.

z COLOR :

According to the supplier’s LCD specification.

z LCD MTBF :

According to the supplier’s LCD specification.

z BACKLIGHT MTBF :

According to the supplier’s LCD specification.

z DIMENSION :

According to the supplier’s LCD specification.

TOUCH SCREEN : (OPTIONAL)

Type Resistive
Static Load

500g (30 ㎝ , 30 Sec)

Hardness 3H
Transparency 82%
Write Life 10,000,000 Times
Knock Life 35,000,000 Times
Chattering Time 10 ms
Input Voltage 5V
Wire 5 Wire

2

Chapter 1 Introduction

Page: 1-8

PPC-7365F USER

′

S MANUAL

GENERAL INFORMATION

z POWER SUPPLY :

DC 16V ~ 30V input, ATX 80W

z DRIVE BAYS (Optional) :

1x Slim HDD
1x Compact Flash Type-II Slot (IDE, On Board)

z CONSTRUCTION :

Electo Galvanized steel chassis.
Aluminium front bezel.

z DIMENSIONS :

400 x 300 x 123mm (15.75” x 11.81” x 4.85”)

z NET WEIGHT :

8 kg

Chapter 1 Introduction

PPC-7365F USER′S MANUAL

Page: 1-9

1-4. SAFETY AND NOTIFICATION

* Please remember to put a Mylar below the hard disk drive while installing it.
* Please note that WinCE does not support for external CF card.

Following messages are safety reminders on how to protect your systems from
damages. And thus, helps you lengthen the life cycle of the system.

1. Check the Line Voltage

a. The operating voltage for the power supply should cover the range of DC

15V~24V, otherwise the system may be damaged.

2. Environmental Conditions

a. Place your PPC-7365F on a sturdy, level surface. Be sure to allow enough

room on each side to have easy access.
b. Avoid extremely hot or cold places to install your PPC.
c. Avoid exposure to sunlight for a long period of time (for example in a

closed car in summer time. Also avoid the system from any heating

device.). Or do not use PPC-7365F when it‘s been left outdoors in a cold

winter day.
d. Bear in mind that the operating ambient temperature is from 0°C up to

+45°C.
e. Avoid moving the system rapidly from a hot place to a cold place or vice

versa because condensation may come from inside of the system.
f. Place PPC-7365F against strong vibrations, which may cause hard disk

failure.
g. Do not place the system too close to any radio active device. Radioactive

device may cause interference.

3. Handling

a. Avoid putting heavy objects on top of the system.
b. Do not turn the system upside down. This may cause the floppy drive and

hard drive to mal-function.
c. Do not remove the diskette from the Floppy drive while the light is still on.

If you remove the diskette while the light is on, you may damage the

information on the diskette.

4. Good Care

a. When the outside of the case is stained, remove the stain with neutral

washing agent with a dry cloth.
b. Never use strong agents such as benzene and thinner to clean the system.
c. If heavy stains are present, moisten a cloth with diluted neutral washing

agent or with alcohol and then wipe thoroughly with a dry cloth.
d. If dust has been accumulated on the outside, remove it by using a special

made vacuum cleaner for computers.

Page 2-1

SYSTEM
CONFIGURATION

Helpful information that describes the jumper & connector settings,
and component locations.

Section includes:

z Jumper & Connector Quick Reference Table

z Component Locations

z Configuration and Jumper settings

z Connector Pin Assignments

CHAPTER

2

Chapter 2 Hardware Configuration

Page: 2-2

PPC-7365F USER

’S MANUAL

2-1. JUMPER & CONNECTOR QUICK REFERENCE TABLE

COM Port Connector ……………………………………....

………………………………………

COM1, COM2
COM3, COM4

COM Port RI & Voltage Selection …………..………….... JP19

RS232/422/485 (COM2) Selection .....................…………. JP3

VGA Connector …………………………………………… VGA1

LVDS Connector ...............................................………….. LVDS1, LVDS2

Brightness Voltage Selection ………………………..…….. JP9
LVDS Voltage Selection …………………………………. JP12
Power Connector …………………………………………. CN1

Floppy Disk Drive Connector …..........................………… FDD1

Hard Disk Drive Connector ….............................………… IDE1

Printer Connector …………………………………………. LPT1

LAN Connector ….......................…....................………… LAN1

LAN LED Connector ……………………………………… LANLED1
Keyboard Connector ……………………………………… KB1
PS/2 Mouse Connec

t

or ……...........................……………. MS1

Sound Connector ………………………………………….. LINE1, MIC1, SPK1
Onboard Audio Selection …………………………………. JP11

Reset Connector Switch ...................................………….. JP17

HDD LED Connector …………………………………….. HDLED1
Power Button …………………….……………………….. CN56
External Buzzer Connector ………………………………. JP14 (1-2)
External SMI Connector …………………………………. JP14 (7-8)
CMOS Function Selection ………………………………… JP8
USB Connector …………………………………………… USB1, USB2, USB3, USB4
Reset/NMI Selection ……………………………………… JP7
Wake-On-LAN Connector ………………………………… JWOL1
Power LED Connector ……………………………………. PWLED1

Memory Installation ….........................................………… DIMM1

AT/ATX Power Selection ……………………………….. JP14 (3-6), JP18
Compact Flash Master/Slave Selection ………………….. JP15
IRQ12 Release Selection ………………………………… JP6
LVDS Panel Resolution Selection ………………………… JP16
Inverter Connector ………………………………………. INV1
IDE Power Module ………………………………………. POWER1
Compact Flash Connector ………………………………… CF1
PC104 Connector …………………………………………. PC104
PC104+ Connector ………………………………………… PC104PLUS1
CPU Fan Connector ………………………………………. FAN1
System Fan Connector ……………………………………. FAN2

Chapter 2 Hardware Configuration

PPC-7365F USER’S MANUAL

Page: 2-3

2-2. COMPONENT LOCATIONS

PPC-7365F Connector, Jumper and Component locations

Chapter 2 Hardware Configuration

Page: 2-4

PPC-7365F USER

’S MANUAL

2-3. HOW TO SET THE JUMPERS

You can configure your board by setting the jumpers. Jumper is consists of
two or three metal pins with a plastic base mounted on the card, and by
using a small plastic "cap", Also known as the jumper cap (with a metal
contact inside), you are able to connect the pins. So you can set-up your
hardware configuration by "opening" or "closing" pins.

The jumper can be combined into sets that called jumper blocks. When the
jumpers are all in the block, you have to put them together to set up the
hardware configuration. The figure below shows how this looks like.

JUMPERS AND CAPS

If a jumper has three pins for example, labelled PIN1, PIN2, and PIN3. You
can connect PIN1 & PIN2 to create one setting and shorting. You can either
connect PIN2 & PIN3 to create another setting. The same jumper diagrams
are applied all through this manual. The figure below shows what the manual
diagrams look and what they represent.

Chapter 2 Hardware Configuration

PPC-7365F USER’S MANUAL

Page: 2-5

JUMPER DIAGRAMS

JUMPER SETTINGS

Chapter 2 Hardware Configuration

Page: 2-6

PPC-7365F USER

’S MANUAL

2-4. COM PORT CONNECTOR

There are four COM ports enhanced in this board namely: COM1,
COM2, COM3 and COM4. COM1, COM3 and COM4 are fixed for
RS-232, while COM2 is selectable for RS-232/422/485.

COM1 : COM1 Connector
The COM1 Connector assignments are as follows :

PIN ASSIGNMENT

1 DCD1
2 RX1
3 TX1
4 DTR1
5 GND
6 DSR1
7 RTS1
8 CTS1
9 RI1

COM2 : COM2 Connector
The COM2 Connector assignments are as follows :

PIN ASSIGNMENT

RS-232 RS-422 RS-485

1 DCD2 TX- TX­2 RX2 TX+ TX+
3 TX2 RX+ RX+
4 DTR2 RX- RX­5 GND GND GND
6 DSR2 RTS- NC
7 RTS2 RTS+ NC
8 CTS2 CTS+ NC
9

RI2

CTS- NC

COM1

COM2

Chapter 2 Hardware Configuration

PPC-7365F USER’S MANUAL

Page: 2-7

COM3 : COM3 Connector
The pin assignments are as follows :

PIN ASSIGNMENT

1 DCD3
2 RX3
3 TX3
4 DTR3
5 GND
6 DSR3
7 RTS3
8 CTS3
9 RI3

10 NC

COM4 : COM4 Connector
The pin assignments are as follows :

PIN ASSIGNMENT

1 DCD4
2 RX4
3 TX4
4 DTR4
5 GND
6 DSR4
7 RTS4
8 CTS4
9 RI4

10 NC

 All COM port’s pin 9 is selectable for RI, +5V or +12V. For

more information, please refer to our “2-5 COM RI and Voltage
Selection”.

Chapter 2 Hardware Configuration

Page: 2-8

PPC-7365F USER

’S MANUAL

2-5. COM PORT RI & VOLTAGE SELECTION

JP19 : COM1, COM2, COM3, and COM4 RI & Voltage Selection

The selections are as follows:

SELECTION

JUMPER SETTING

(Pin Closed)

JUMPER

ILLUSTRATION

RI

(default)

1-2

5V

11-13

COM1

12V

9-11

RI

(default)

3-4

5V

12-14

COM2

12V

10-12

Chapter 2 Hardware Configuration

PPC-7365F USER’S MANUAL

Page: 2-9

RI

(default)

5-6

5V

15-17

COM3

12V

17-19

RI

(default)

7-8

5V

16-18

COM4

12V

18-20

Chapter 2 Hardware Configuration

Page: 2-10

PPC-7365F USER

’S MANUAL

2-6. RS232/422/485 (COM2) SELECTION

JP3 : RS-232/422/485 (COM2) Selection
COM2 is selectable for RS-232, 422, 485 function.
The jumper settings are as follows :

COM 2

FUNCTION

JUMPER SETTING

(pin closed)

JUMPER ILLUSTRATION

RS-232

(default)

Open

RS-422

1-2, 5-6, 7-8, 9-10

11-12, 13-14, 15-16

17-18, 19-20

RS-485

1-3, 4-6, 7-8, 9-10

11-12, 13-14, 15-16

17-18, 19-20

Chapter 2 Hardware Configuration

PPC-7365F USER’S MANUAL

Page: 2-11

2-7. VGA CONNECTOR

VGA : VGA Connector
The pin assignments are as follows:

PIN ASSIGNMENT

1 RED
2 GREEN
3 BLUE
4 NC
5 GND
6 GND
7 GND
8 GND

9 VCC
10 GND
11 NC
12 VGA IIC DATA
13 HSYNC
14 VSYNC
15 VGA IIC CLK
16 NC

Chapter 2 Hardware Configuration

Page: 2-12

PPC-7365F USER

’S MANUAL

2-8. LVDS CONNECTOR

LVDS1 : LVDS Connector
The pin assignments are as follows :

PIN ASSIGNMENT PIN ASSIGNMENT

1 GND 12 YCM
2 GND 13 GND
3 Y2P 14 GND
4 NC 15 Y0P
5 Y2M 16 GND
6 NC 17 Y0M
7 GND 18 LVDSVCC
8 GND 19 GND
9 Y1P 20 LVDSVCC

10 YCP
11 Y1M

LVDS2 : LVDS Connector
The pin assignments are as follows :

PIN ASSIGNMENT PIN ASSIGNMENT

1 GND 12 ZCM
2 GND 13 GND
3 Z2P 14 GND
4 NC 15 Z0P
5 Z2M 16 GND
6 NC 17 Z0M
7 GND 18 LVDSVCC
8 GND 19 GND
9 Z1P 20 LVDSVCC

10 ZCP
11 Z1M

Chapter 2 Hardware Configuration

PPC-7365F USER’S MANUAL

Page: 2-13

2-9. BRIGHTNESS VOLTAGE SELECTION

JP9: Brightness Voltage Selection
The selections are as follows :

SELECTION

JUMPER SETTING

(Pin Closed)

JUMPER

ILLUSTRATION

5V

(default)

2-3

2.5V

1-2

Chapter 2 Hardware Configuration

Page: 2-14

PPC-7365F USER

’S MANUAL

2-10. LVDS VOLTAGE SELECTION

JP12: LCD Voltage Selection
The selections are as follows :

SELECTION

JUMPER SETTING

(Pin Closed)

JUMPER

ILLUSTRATION

12V

1-2

3.3V

(default)

3-4

5V

5-6

Chapter 2 Hardware Configuration

PPC-7365F USER’S MANUAL

Page: 2-15

2-11. POWER CONNECTOR

CN1: Power Connector

The pin assignments are as follows :

PIN ASSIGNMENT

1 5V

2 5V

3 GND

4 GND

5 12V

6 5VSB

7 5V

8 GND

9 PS_ON
10 -12V

Chapter 2 Hardware Configuration

Page: 2-16

PPC-7365F USER

’S MANUAL

2-12. FLOPPY DISK DRIVE CONNECTOR

FDD1 : Floppy Disk Drive Connector
The pin assignments are as follows:

PIN ASSIGNMENT PIN ASSIGNMENT

2 INDEXJ 1 5V
4 DRVAJ 3 5V
6 DSKCHGJ 5 5V

8 NC 7 NC
10 MOTEAJ 9 NC
12 FDIRJ 11 NC
14 STEPJ 13 DENSELJ
16 WDATAJ 15 NC
18 WGATEJ 17 GND
20 TK00J 19 GND
22 WPTJ 21 GND
24 RDATAJ 23 GND
26 SIDE1J 25 GND

Chapter 2 Hardware Configuration

PPC-7365F USER’S MANUAL

Page: 2-17

2-13. HARD DISK DRIVE CONNECTOR

IDE1 : Hard Disk Drive Connector
The pin assignments are as follows:

PIN ASSIGNMENT PIN ASSIGNMENT

1 IDERSTJ 2 GND
3 PDD7 4 PDD8
5 PDD6 6 PDD9
7 PDD5 8 PDD10

9 PDD4 10 PDD11
11 PDD3 12 PDD12
13 PDD2 14 PDD13
15 PDD1 16 PDD14
17 PDD0 18 PDD15
19 GND 20 NC
21 DDREQA 22 GND
23 DIOWAJ 24 GND
25 DIORAJ 26 GND
27 HDRDYA 28 PULL LOW
29 DDACKAJ 30 GND
31 IDE_IRQ14 32 NC
33 PDA1 34 PD_80P
35 PDA0 36 PDA2
37 PDCSJ1 38 PDCSJ3
39 HDLEDJ1 40 GND
41 5V 42 5V
43 GND 44 NC

Chapter 2 Hardware Configuration

Page: 2-18

PPC-7365F USER

’S MANUAL

2-14. PRINTER CONNECTOR

LPT1 : Printer Connector
As to link the Printer to the card, you need a cable to connect both DB25
connector and parallel port.
The pin assignments are as follows :

LPT1

PIN ASSIGNMENT PIN ASSIGNMENT

1 STROBE 14 AFDJ

2 PPD0 15 ERRORJ

3 PPD1 16 INITJ

4 PPD2 17 SLINJ

5 PPD3 18 GND

6 PPD4 19 GND

7 PPD5 20 GND

8 PPD6 21 GND

9 PPD7 22 GND

10 ACKJ 23 GND
11 BUSY 24 GND
12 PE 25 GND
13 SLCT

Chapter 2 Hardware Configuration

PPC-7365F USER’S MANUAL

Page: 2-19

2-15. LAN CONNECTOR

LAN1: LAN Connector.
The pin assignment is as follows :

PIN ASSIGNMENT

1 MDI_0P
2 MDI_0N
3 MDI_1P
4 MDI_2P
5 MDI_2N
6 MDI_1N
7 MDI_3P
8 MDI_3N

2-16. LAN LED CONNECTOR

LANLED1 : LAN LED Connector
The pin assignment is as follows :

PIN ASSIGNMENT

1 LED100
2 CONTROL
3 LED1000

Chapter 2 Hardware Configuration

Page: 2-20

PPC-7365F USER

’S MANUAL

2-17. KEYBOARD CONNECTOR

KB1 : PC/AT Keyboard Connector
The pin assignments are as follows :

PIN ASSIGNMENT

1 KB DATA
2 NC
3 GND
5 5VSB
6 KB CLK
8 NC

2-18. PS/2 MOUSE CONNECTOR

MS1 : PS/2 Mouse Connector
The pin assignments are as follows :

PIN ASSIGNMENT

1 MS DATA
2 NC
3 GND
5 5VSB
6 MS CLK
8 NC

1

2

3

5

6

8

KB1

1

2

3

5

6

8

MS1

Chapter 2 Hardware Configuration

PPC-7365F USER’S MANUAL

Page: 2-21

2-19. SOUND CONNECTOR

The sound connector is composed of the Microphone (MIC1), Line-Out
(SPK1), and Line-In (LINE1).

LINE1 : Line-In Connector
The pin assignment is as follows :

PIN ASSIGNMENT

1 GND
2 LINE_L
3 LINE_R

MIC1 : Microphone Connector
The pin assignment is as follows :

PIN ASSIGNMENT

1 GND
2 MIC_IN1
3 MIC_IN2

SPK1 : Line-Out Connector
The pin assignment is as follows :

PIN ASSIGNMENT

1 GND
2 Line-out-L
3 Line-out-R

Chapter 2 Hardware Configuration

Page: 2-22

PPC-7365F USER

’S MANUAL

2-20. ONBOARD AUDIO SELECTION

JP11: Onboard Audio Selection
The selections are as follows:

FUNCTION

JUMPER SETTING

(pin closed)

JUMPER

ILLUSTRATION

On

(default)

1-2

Off open

2-21. RESET CONNECTOR SWITCH

JP17 : Reset Connector Switch.
The pin assignment is as follows :

PIN ASSIGNMENT

1 GND
2 RST SW

2-22. HDD LED CONNECTOR

HDLED1 : HDD LED Connector
The pin assignment is as follows :

PIN ASSIGNMENT

1 HD_LED+
2 HD_LED-

Chapter 2 Hardware Configuration

PPC-7365F USER’S MANUAL

Page: 2-23

2-23. POWER BUTTON

CN56 : Power Button
The pin assignments are as follows:

PIN ASSIGNMENT

1 PWR_BN1
2 PWR_BN2

2-24. EXTERNAL BUZZER CONNECTOR

JP14 (1-2) : External Buzzer Connector.
The pin assignments are as follows :

PIN ASSIGNMENT

1 E_BUZ_PWR
2 E_BUZ

2-25. EXTERNAL SMI CONNECTOR

JP14 (7-8) : External SMI Connector.
The pin assignments are as follows :

PIN ASSIGNMENT

7 GND
8 EXTSMIJ

Chapter 2 Hardware Configuration

Page: 2-24

PPC-7365F USER

’S MANUAL

2-26. CMOS FUNCTION SELECTION

JP8: CMOS Function Selection
The selections are as follows:

FUNCTION

JUMPER SETTING

(pin closed)

JUMPER

ILLUSTRATION

NORMAL

(default)

1-2

CLEAR CMOS

2-3



To clear CMOS data, user must power-off the computer and set the jumper to

“Clear CMOS” as illustrated above. After five to six seconds, set the jumper back
to “Normal” and power-on the computer.

Chapter 2 Hardware Configuration

PPC-7365F USER’S MANUAL

Page: 2-25

2-27. UNIVERSAL SERIAL BUS CONNECTOR

USB1: Universal Serial Bus Connector.
The pin assignments are as follows :

PIN ASSIGNMENT

1 VCCUSB0
2 USB0N_R
3 USB0P_R
4 GND

USB2: Universal Serial Bus Connector.
The pin assignments are as follows :

PIN ASSIGNMENT

1 VCCUSB1
2 USB1N_R
3 USB1P_R
4 GND

USB3 : Universal Serial Bus Connector.
The pin assignments are as follows :

PIN ASSIGNMENT

1 VCCUSB2
2 USB2N_R
3 USB2P_R
4 GND
5 GND

4321

USB1

4321

USB2

Chapter 2 Hardware Configuration

Page: 2-26

PPC-7365F USER

’S MANUAL

USB4 : Universal Serial Bus Connector.
The pin assignments are as follows :

PIN ASSIGNMENT

1 VCCUSB3
2 USB3N_R
3 USB3P_R
4 GND
5 GND

2-28. RESET / NMI SELECTION

JP7 : Reset/NMI/Clear Watchdog Selection
The selections are as follows:

FUNCTION JUMPER SETTING

JUMPER

ILLUSTRATION

Reset

(default)

1-2

NMI 3-4

 User may select to use the Reset or NMI watchdog. NMI, also known as Non-Maskable

Interrupt, is used for serious conditions that demand the processor’s immediate attention,
it cannot be ignored by the system unless it is shut off specifically. To clear NMI
command, user should short the “Clear Watchdog” pin via push button.

Chapter 2 Hardware Configuration

PPC-7365F USER’S MANUAL

Page: 2-27

2-29. WAKE-ON-LAN CONNECTOR

JWOL1 : Wake-On-LAN Connector
The pin assignments are as follows :

PIN ASSIGNMENT

1 +5VSB
2 GND
3 WOL1

2-30. POWER LED CONNECTOR

PWLED1: Power LED Connector.
The pin assignments are as follows :

PIN ASSIGNMENT

1 PW_LED+
2 GND

2-31. MEMORY INSTALLATION

This system is enhanced with 1 DDR DRAM banks, which support up to
1G.

DRAM BANK CONFIGURATION

DIMM 1 TOTAL MEMORY

128M 128MB
256M 256MB
512M 512MB

1G 1G

Chapter 2 Hardware Configuration

Page: 2-28

PPC-7365F USER

’S MANUAL

2-32. AT/ATX POWER SELECTION

JP14 (3-6) : AT/ATX Power Selection

The selections are as follows:

FUNCTION JUMPER SETTING

JP14 (3-6) JP18

JUMPER

ILLUSTRATION

AT

3-4, 5-6 Open

ATX

(default)

open 1-2

Chapter 2 Hardware Configuration

PPC-7365F USER’S MANUAL

Page: 2-29

2-33. COMPACT FLASH MASTER/SLAVE SELECTION

JP15 : Compact Flash Master/Slave Selection
The selections are as follows:

FUNCTION JUMPER SETTING

JUMPER

ILLUSTRATION

Master

(default)

1-2

Slave open

2-34. IRQ12 RELEASE SELECTION

JP6 : IRQ12 Release Selection.
The selections are as follows:

SELECTION JUMPER SETTING

JUMPER

ILLUSTRATION

IRQ12 Release Closed

PS/2 Mouse

(default)

Open

Chapter 2 Hardware Configuration

Page: 2-30

PPC-7365F USER

’S MANUAL

2-35. LVDS PANEL RESOLUTION SELECTION

JP16 : LVDS Panel Resolution Selection.

The selections are as follows:

FUNCTION

JUMPER SETTING

(pin closed)

JUMPER

ILLUSTRATION

800 x 600

1-2

1024 x 768

(default)

3-4

2-36. INVERTER CONNECTOR

INV1: Inverter Connector.
The pin assignments are as follows :

PIN ASSIGNMENT

1 VCC12
2 GND
3 BRCTR
4 NC
5 ENVEE (Inverter backlight

On/Off control signal)

Chapter 2 Hardware Configuration

PPC-7365F USER’S MANUAL

Page: 2-31

2-37. POWER MODULE

POWER1 : Power Module.
The pin assignments are as follows :

PIN ASSIGNMENT PIN ASSIGNMENT

1 +5V 2 5VSB
3 +5V 4 5VSB
5 +5V 6 5VSB
7 +5V 8 +5V

9 +5V 10 +5V
11 +5V 12 +5V
13 GND 14 GND
15 GND 16 GND
17 GND 18 GND
19 PS-ON 20 GND
21 NC 22 GND
23 NC 24 GND
25 -12V 26 +12V
27 -12V 28 +12V
29 -12V 30 +12V
31 NC 32 NC
33 NC 34 NC
35 NC 36 NC
37 NC 38 NC
39 NC 40 NC

Chapter 2 Hardware Configuration

Page: 2-32

PPC-7365F USER

’S MANUAL

2-38. COMPACT FLASH CONNECTOR

CF1 : Compact Flash Connector.
The pin assignments are as follows :

PIN ASSIGNMENT PIN ASSIGNMENT

1 GND 26 GND
2 D03 27 D11
3 D04 28 D12
4 D05 29 D13
5 D06 30 D14
6 D07 31 D15
7 CSJ1 32 CSJ3
8 GND 33 GND

9 GND 34 SDIORDJ
10 GND 35 SDIOWRJ
11 GND 36 +5V
12 GND 37 IRQ15
13 +5V 38 +5V
14 GND 39 -CSEL
15 GND 40 NC
16 GND 41 RESETJ
17 GND 42 IORDY
18 A02 43 REQ
19 A01 44 ACKJ
20 A00 45 CF_LEDJ
21 D00 46 -PDIAG
22 D01 47 D08
23 D02 48 D09
24 NC 49 D10
25 GND 50 GND

Chapter 2 Hardware Configuration

PPC-7365F USER’S MANUAL

Page: 2-33

2-39. PC104 CONNECTOR

PC104 : PC104 Connector.
The pin assignments are as follows :

PIN ASSIGNME

NT

PIN ASSIGNME

NT

PIN ASSIGNME

NT

PIN ASSIGNME

NT

A1 IOCHK B1 GND C1 GND D1 GND
A2 D7 B2 REST C2 SBHEJ D2 MEMCS16J
A3 D6 B3 +5V C3 LA23 D3 IOCS16J
A4 D5 B4 IRQ9 C4 LA22 D4 IRQ10
A5 D4 B5 NC C5 LA21 D5 IRQ11
A6 D3 B6 DREQ2 C6 LA20 D6 IRQ12
A7 D2 B7 -12V C7 LA19 D7 IRQ15
A8 D1 B8 NOWS C8 LA18 D8 IRQ14
A9 D0 B9 +12V C9 LA17 D9 DACKJ0
A10 IOCHRDY B10 GND C10 MEMRJ D10 DREQ0
A11 AEN B11 SMEMWJ C11 MEMWJ D11 DACKJ5
A12 A19 B12 SMEMRJ C12 D8 D12 DREQ5
A13 A18 B13 IOWJ C13 D9 D13 DACKJ6
A14 A17 B14 IORJ C14 D10 D14 DREQ6
A15 A16 B15 DACKJ3 C15 D11 D15 DACKJ7
A16 A15 B16 DREQ3 C16 D12 D16 DREQ7
A17 A14 B17 DACKJ1 C17 D13 D17 +5V
A18 A13 B18 DREQ1 C18 D14 D18 MASTERJ
A19 A12 B19 REFRESHJ C19 D15 D19 GND
A20 A11 B20 SYSCLK C20 NC D20 GND
A21 A10 B21 IRQ7
A22 A9 B22 IRQ6
A23 A8 B23 IRQ5
A24 A7 B24 IRQ4
A25 A6 B25 IRQ3
A26 A5 B26 DACKJ2
A27 A4 B27 TC
A28 A3 B28 BALE
A29 A2 B29 +5V
A30 A1 B30 OSC
A31 A0 B31 GND
A32 GND B32 GND

Chapter 2 Hardware Configuration

Page: 2-34

PPC-7365F USER

’S MANUAL

2-40. PC104+ CONNECTOR

PC104PLUS1 : PC104+ Connector.
The pin assignments are as follows :

A B C D

PIN ASSIGNMENT PIN ASSIGNMENT PIN ASSIGNMENT PIN ASSIGNMENT

A1 GND B1 SERIR C1 +5V D1 AD00
A2 NC B2 AD02 C2 AD01 D2 +5V
A3 AD05 B3 GND C3 AD04 D3 AD03
A4 CBEJ0 B4 AD07 C4 GND D4 AD06
A5 GND B5 AD09 C5 AD08 D5 GND
A6 AD11 B6 NC C6 AD10 D6 M66EN
A7 AD14 B7 AD13 C7 GND D7 AD12
A8 +3.3V B8 CBEJ1 C8 AD15 D8 +3.3V
A9 SERRJ B9 GND C9 NC D9 PAR
A10 GND B10 PERRJ C10 +3.3V D10 SDONE
A11 STOPJ B11 +3.3V C11 LOCKJ D11 GND
A12 +3.3V B12 TRDYJ C12 GND D12 DEVSELJ
A13 FRAMEJ B13 GND C13 IRDYJ D13 +3.3V
A14 GND B14 AD16 C14 +3.3V D14 CBEJ2
A15 AD18 B15 +3.3V C15 AD17 D15 GND
A16 AD21 B16 AD20 C16 GND D16 AD19
A17 +3.3V B17 AD23 C17 AD22 D17 +3.3V
A18 IDSEL0 B18 GND C18 IDSEL1 D18 IDSEL2
A19 AD24 B19 CBEJ3 C19 NC D19 IDSEL3
A20 GND B20 AD26 C20 AD25 D20 GND
A21 AD29 B21 +5V C21 AD28 D21 AD27
A22 +5V B22 AD30 C22 GND D22 AD31
A23 REQJ0 B23 GND C23 REQJ1 D23 NC
A24 GND B24 REQJ2 C24 +5V D24 GNTJ0
A25 GNTJ1 B25 NC C25 GNTJ2 D25 GND
A26 +5V B26 PCLK1 C26 GND D26 PCLK2
A27 PCLK3 B27 +5V C27 PCLK4 D27 GND
A28 GND B28 INTDJ C28 +5V D28 RSTJ
A29 +12V B29 INTAJ C29 INTBJ D29 INTCJ
A30 NC B30 NC C30 NC D30 GND

Chapter 2 Hardware Configuration

PPC-7365F USER’S MANUAL

Page: 2-35

2-41. CPU FAN CONNECTOR

FAN1 : CPU Fan Connector
The pin assignments are as follows:

PIN ASSIGNMENT

1 GND
2 +12V
3 CPUFAN1

2-42. SYSTEM FAN CONNECTOR

FAN2 : System FAN Connector
The pin assignments are as follows:

PIN ASSIGNMENT

1 +5V
2 GND

Page: 3-1

SOFTWARE
UTILITIES

This chapter comprises the detailed information of VGA driver, LAN
driver, and sound driver, VIA Chipset Software Installation Utility,
touch screen driver, USB 2.0 driver and Flash BIOS update. It also
describes how to install the watchdog timer configuration.

Section includes:

z Introduction

z VIA 4 IN1 Service Pack Driver Utility

z VGA Driver Utility

z Flash BIOS Update

z LAN Driver Utility

z Sound Driver Utility

z USB2.0 Chipset Software Installation Utility

z Touch screen Driver Utility (Optional)

z USB CF CARD Driver Utility (Optional)

z Watchdog Timer Configuration

CHAPTER

3

Chapter 3 Software Configuration

Page:3-2

PPC-7365F USER

′

S MANUAL

3-1. INTRODUCTION

Enclosed with our PPC-7365F package is our driver utility, which may
comes in a form of a CD ROM disc or floppy diskettes. For CD ROM disc
user, you will only need some of the files contained in the CD ROM disc,
please kindly refer to the following chart:

Filename

(Assume that CD ROM drive is D:)

Purpose

D:\Utility\
***Install this software first!

VIA 4in1 Service Pack Driver

Utility
D:\VGA Drv\ For VGA driver installation
D:\BIOS Flash\ For flash BIOS update
D:\ Lan Drv\ For LAN Driver installation
D:\ Sound Drv\ Analog Device VT1612A

For Sound driver installation
D:\ USB2.0 Drv\ USB 2.0 Software Installation

Utility

For Win 98SE, 2000, ME, XP
D:\Touch Screen Drv\ For Liyi Touch screen driver
D:\ USB CF Card Drv\ For USB CF Card Driver

Installation

3-2. VIA 4IN1 SERVICE PACK DRIVER

3-2-1. Introduction

The 4-in-1 drivers are a collection of periodically updated drivers that
provide enhanced VIA chipset to support under Microsoft Windows.
This drivers should be installed after the OS is fully installed, to improve
performance, fix issues, and minimize any incompatibilities.

The VIA 4 In 1 driver includes four system drivers to improve the
performance and maintain the stability of systems using VIA chipsets.
These four drivers are: VIA Registry (INF) Driver, VIA AGP VxD
driver, VIA ATAPI Vendor Support Driver and VIA PCI IRQ Miniport
Driver

Chapter 3 Software Configuration

PPC-7365F USER′S MANUAL

Page:3-3

1. Win 95 program

2. Win 2000 program

3. Win 98/SE program

4. Win ME program

3-3. VGA DRIVER UTILITY

3-3-1. Introduction

The VGA interface embedded with our PPC-7365F can support a wide

range of display mode, such as SVGA, STN, TFT,.....etc. You can display

CRT and LCD Panel simultaneously on this board, but make sure that the
modes for CRT and LCD Panel are the same. If not, only one of them can
be displayed.

1.

2.

3. Win 2000/XP program

4. Linux program

Win 98 program
Win NT program

Chapter 3 Software Configuration

Page:3-4

PPC-7365F USER

′

S MANUAL

3-3-2. Installation of VGA Driver

1. Install VGA Driver to Windows 98/2000/XP

(1). Place insert the Driver CD into CD ROM drive.
(2). Under Windows 98/2000/XP system, go to the directory where

VGA driver is located.

(3). Click Setup.exe file for VGA driver installation.
(4). Follow the instructions on the screen to complete the installation.
(5). Once installation is completed, shut do wn the system and restart

in order for the changes to take effect.

2. Install VGA driver to Windows NT 4.0

(1). To install Driver CD to Windows NT4.0 is as you normally

would. Click START, then SETTINGS, then CONTROL
PANEL of the operating system.

(2). Select the DISPLAY icon to start the DISPLAY PROPERTIES

window, then choose the SETTING tab, then DISPLAY TYPE.

(3). In the CHANGE DISPLAY TYPE window, click on the

CHANGE button in the ADAPTER TYPE, this will bring up the
SELECT DEVICE window.

(4). In the CHANGE DISPLAY window, click on Have Disk.

Follow the instructions appearing on the screen until you
complete the whole installation.

(5). Once installation is completed, the system must be shut down

and restarted for the new drivers to take effect.

3-4. FLASH BIOS UPDATE

3-4-1. Introduction

Users of PPC-7365F can use the program “Awdflash.exe” contained in the
Utility Disk for system BIOS update.

3-4-2. Installation of system BIOS

1. Copy “Awdflash.exe” from Driver Disk to Drive C.

2. Type the path to Awdflash.exe and execute the system BIOS

AWDFLASH s55xxxxx.bin

3. The screen will display the table below:

Chapter 3 Software Configuration

PPC-7365F USER′S MANUAL

Page:3-5

FLASH MEMORY WRITER V7.XX

(C) Award Software 2001 All Rights Reserved

Flash Type - MX29F004T

File Name to Program: s55xxxxx.bin

Error Message : Do You Want To Save BIOS (Y/N)

If you want to save up the original BIOS, enter "Y" and press < Enter > .
If you choose "N", the following table will appear on screen.

FLASH MEMORY WRITER V7.XX

(C) Award Software 2001 All Rights Reserved

Flash Type - MX29F004T

File Name to Program: s55xxxxx.bin

Error Message : Are You Sure To Program (Y/N)

Select "Y", and the BIOS will be renewed. When you are refreshing the
BIOS, do not turn off or reset the system, or you will damage the BIOS.
After you have completed all the programming, the screen displays the
table below:

Chapter 3 Software Configuration

Page:3-6

PPC-7365F USER

′

S MANUAL

FLASH MEMORY WRITER V7.XX

(C) Award Software 2001 All Rights Reserved

Flash Type – MX29F004T

File Name to Program: s55xxxxx.bin

Verifying Flash Memory – 7FFFF OK

Write OK No Update Write Fail

F1: Reset F10: Exit

Please reset or power off the system, then the Flash BIOS is fully
implemented.

3-5. LAN DRIVER UTILITY

3-5-1. Introduction

The PPC-7365F Panel PC is enhanced with LAN function that can
support various network adapters. Installation programs for LAN
drivers are listed as follows:

1. Windows 9x

2. Windows NT

3. Windows 2000

4. Netware

5. DOS

6. Linux

Chapter 3 Software Configuration

PPC-7365F USER′S MANUAL

Page:3-7

3-5-2. Installation Procedure for Windows 9x

1. Place insert the Driver CD into CD ROM drive.

2. Under Windows 9x/2000 system, go to the directory where LAN

driver is located.

3. Click Setup.exe file for LAN driver in stallation.

4. Follow the instructions on the screen to complete the installation.

5. Once installation is completed, sh ut down the system and restart in

order for the changes to take effect.

3-5-3. Installation Procedure for Windows NT

1. In the Main group to NT, select the “Control Panel” icon.

2. In the Control Panel window, choose the “Network” icon.

3. In the Network Settings dialog box, choose the “Add adapter”

button. The Add Network Adapter dialog box appears.

4. In the list of network cards, select “<Other> requires disk from

manufacturer”, and then press <Enter> button.

5. Insert the LAN Driver disk in Drive A o r CDROM drive, and type

D:\LAN, and then choose OK button.

6. Follow the remaining instruction, and re-boot your system to

complete the installation process.

For more information on installation procedure, please refer to TXT
directory found on LAN DRIVER UTILITY.

3-6. SOUND DRIVER UTILITY

3-6-1. Introduction

The VT1612A sound function enhanced in this system is fully
compatible with Windows 98, Windows NT 4.0, and Windows 2000.
Below, you will find the content of the Sound driver :

Chapter 3 Software Configuration

Page:3-8

PPC-7365F USER

′

S MANUAL

1. Win 98 program

2. Win program

3. Win program

4. Win XP program

NT 4.0
2000

3-6-2. Installation Procedure for Windows 9x/NT/2000

1. From the task bar, click on Start, and then Run.

2. In the Run dialog box, type D:\Sound\setup, where

“D:\Sound\pathname” refers to the full path to the source files.

3. Click on the OK button or press the ENTER key.

4. Click on the “Next” and OK prompts as they appear.

5. Reboot the system to complete the driver installation.

3-7. USB2.0 SOFTWARE INSTALLATION UTILITY

3-7-1. Installation of Utility for Windows 98SE/ 2000/XP

Intel USB 2.0 Enhanced Host Controller driver can only be used on
Windows 98SE, Windows 2000 and Windows XP on Intel Desktop
boards. It should be installed right after the OS installation, kindly
follow the following steps:

1. Place insert the USB Disk into Floppy Disk Drive A/B or CD ROM

drive.

2. Under Windows 98SE/2000/XP system, go to the directory where

USB driver is located.

3. Click Setup.exe file for USB driver installation.

4. Follow the instructions on the screen to complete the installation.

5. Once installation is completed, sh ut down the system and restart in

order for the changes to take effect.

Chapter 3 Software Configuration

PPC-7365F USER′S MANUAL

Page:3-9

3-8. TOUCH SCREEN DRIVER UTILITY (OPTIONAL)

To install, kindly refer to the readme.txt file found each separate file of the
Driver Disc.

3-9. USB CF CARD DRIVER UTILITY (OPTIONAL)

To install, kindly refer to the readme.txt file found each separate file of the
Driver Disc.

3-10. WATCHDOG TIMER CONFIGURATION

This board has watchdog timer function for monitoring whether the system is
still work or not after a period of time. The user can select watchdog timer
to system reset or NMI (Non Maskable interrupt) depending on the jumper
set in “Reset/NMI/Clear Watchdog Selection” found in chapter 2. This is
defined at I/O port 443H. When you want to enable the watchdog timer,
please write I/O port 443H, and then the system will either reset itself or
perform the NMI function. Likewise, when you want to disable the function,
write I/O port 441H, the system will run the command to stop the Watchdog
function.

In PPC-7365F watchdog function, you must write your program so when it
writes I/O port address 443 for enable watchdog and write I/O port address
441 for disable watchdog. The timer's intervals have a tolerance of 25% so
you should program an instruction that will refresh the timer about every
second.

The following program shows you how to program the watch timer in your
program.

Watchdog enable program:

MOV AX, 000FH (choose the values you need; start from 0)
MOV DX, 443H
OUT DX, AX

Watchdog disable program:

MOV AX, 000FH (this value can be ignored)

Chapter 3 Software Configuration

Page:3-10

PPC-7365F USER

′

S MANUAL

MOV DX, 441H
OUT DX, AX

The Watchdog Timer control table is as follows:

Level Value Time/sec Level Value Time/sec

1 F 0 9 7 64
2 E 8 10 6 72
3 D 16 11 5 80
4 C 24 12 4 88
5 B 32 13 3 96
6 A 40 14 2 104
7 9 48 15 1 112
8 8 56 16 0 120

Page: 4-1

AWARD
BIOS SETUP

This chapter shows how to set up the Award BIOS.

Section includes:

z Introduction

z Entering Setup

z The Standard CMOS Features

z The Advanced BIOS Features

z The Advanced Chipset Features

z Integrated Peripherals

z Power Management Setup

z PNP/PCI Configurations

z PC Health Status

z Frequency/Voltage Control

z Load Fail-Safe Defaults

z Load Optimized Defaults

z Password Setting

z Save and Exit Setup

z Exit Without Saving

CHAPTER

4

Chapter 4 Award BIOS Setup

Page: 4-2

PPC-7365F USER

′

S MANUAL

4-1. INTRODUCTION

This chapter will show you the function of the BIOS in managing the
features of your system. The PPC-7365F Panel PC is equipped with the
BIOS for system chipset from Award Software Inc. This page briefly
explains the function of the BIOS in managing the special features of your
system. The following pages describe how to use the BIOS for system
chipset Setup menu.

Your application programs (such as word processing, spreadsheets, and
games) rely on an operating system such as DOS or OS/2 to manage such
things as keyboard, monitor, disk drives, and memory.

The operating system relies on the BIOS (Basic Input and Output system), a
program stored on a ROM (Read-only Memory) chip, to initialize and
configure your computer's hardware. As the interface between the hardware
and the operating system, the BIOS enables you to make basic changes to
your system's hardware without having to write a new operating system.

The following diagram illustrates the interlocking relationships between the
system hardware, BIOS, operating system, and application program:

Chapter 4 Award BIOS Setup

PPC-7365F USER′S MANUAL

Page: 4-3

4-2. ENTERING SETUP

When the system is powered on, the BIOS will enter the Power-On Self
Test (POST) routines and the following message will appear on the lower
screen:

PRESS <DEL> TO ENTER SETUP, ESC TO SKIP MEMORY TEST

As long as this message is present on the screen you may press the <Del>

key (the one that shares the decimal point at the bottom of the number
keypad) to access the Setup program. In a moment, the main menu of the
Award SETUP program will appear on the screen:

Phoenix - AwardBIOS CMOS Setup Utility

►Standard CMOS Features

►Advanced BIOS Features

►Advanced Chipset Features

►Integrated Peripherals

►Power Management Setup

►PnP/PCI Configurations

►PC Health Status

►Frequency/Voltage Control

Load Fail-Safe Defaults

Load Optimized Defaults

Set Supervisor Password

Set User Password

Save & Exit Setup

Exit Without Saving

Esc : Quit ↑↓→← : Select Item
F10 : Save & Exit Setup

Time, Date, Hard Disk Type .…

Setup program initial screen

You may use the cursor the up/down keys to highlight the individual menu
items. As you highlight each item, a brief description of the highlighted
selection will appear at the bottom of the screen.

Chapter 4 Award BIOS Setup

Page: 4-4

PPC-7365F USER

′

S MANUAL

4-3. THE STANDARD CMOS FEATURES

Highlight the〝STANDARD CMOS FEATURES〞and press the <ENTER>
key and the screen will display the following table:

Phoenix - AwardBIOS CMOS Setup Utility

Standard CMOS Features

Date (mm:dd:yy)
Time (hh:mm:ss)

Thu, NOV 11 2004
12 : 47 : 28

Item Help

▶ IDE Primary Master
▶ IDE Primary Slave
▶ IDE Secondary Master
▶ IDE Secondary Slave

Drive A
Drive B

Video
Halt On

Base Memory
Extended Memory
Total Memory

[IC25N020ATCS04-0]
[None]
[None]
[None]

[1.44M, 3.5 in.]
[None]

[EGA/VGA]
[All, But Keyboard]

640K
113664K
114688K

Menu Level ►

Change the day, month,
year and century

↑↓→←:Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5: Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults

CMOS Setup screen

In the above Setup Menu, use the arrow keys to highlight the item and then use
the <PgUp> or <PgDn> keys to select the value you want in each item.

Date:

< Month >, < Date > and <Year >. Ranges for each value are in the CMOS
Setup Screen, and the week-day will skip automatically.

Time:

< Hour >, < Minute >, and < Second >. Use 24 hour clock format, i.e., for PM
numbers, add 12 to the hour. For example: 4: 30 P.M. You should enter the
time as 16:30:00.

Chapter 4 Award BIOS Setup

PPC-7365F USER′S MANUAL

Page: 4-5

IDE Primary Master / Slave:
IDE Secondary Master / Slave:

The BIOS can automatically detect the specifications and optimal operating
mode of almost all IDE hard drives. When you select type AUTO for a hard
drive, the BIOS detect its specifications during POST, every time system
boots.

If you do not want to select drive type AUTO, other methods of selecting
drive type are available:

1. Match the specifications of your installed IDE hard drive(s) with the

preprogrammed values for hard drive types 1 through 45.

2. Select USER and enter values into each drive parameter field.

3. Use the IDE HDD AUTO DETECTION function in Setup.

Here is a brief explanation of drive specifications:

• Type: The BIOS contains a table of pre-defined drive types. Each

defined drive type has a specified number of cylinders, number of heads,
write pre-compensation factor, landing zone, and number of sectors.
Drives whose specifications do not accommodate any predefine type are
classified as type USER.

• Size: Disk drive capacity (approximate). Note that this size is usually

greater than the size of a formatted disk given by a disk-checking
program.

• Cyls: number of cylinders.

• Head: number of heads.

• Precomp: write pre-compensation cylinders.

• Landz: landing zone.

• Sector: number of sectors.

• Mode: Auto, Normal, Large or LBA.

• Auto: The BIOS automatically determines the optimal mode.

 Normal: Maximum number of cylinders, heads, sectors supported

are 1024, 16 and 63.

 Large: For drives that do not support LBA and have more than

1024 cylinders.

Chapter 4 Award BIOS Setup

Page: 4-6

PPC-7365F USER

′

S MANUAL

 LBA (Logical Block Addressing): During drive accesses, the IDE

controller transforms the data address described by sector, head
and cylinder number into a physical block address, significantly
improving data transfer rates. For drives greater than 1024
cylinders.

DRIVE A AND DRIVE B:

Select the type of floppy disk drive installed in your system. The available
options are 360KB 5.25in, 1.2KB 5.25in, 720KB 3.5in, 1.44MB 3.5in,

2.88MB 3.5in and None.

VIDEO:

This category selects the type of video adapter used for the primary system
monitor. Although secondary monitors are supported, you do not have to
select the type in Setup. Available Options are as follows:

EGA/VGA Enhanced Graphics Adapter/Video Graphics Array.

For EGA, VGA, SEGA, SVGA or PGA monitor

adapters.
CGA 40 Color Graphics Adapter, power up in 40 column mode.
CGA 80 Color Graphics Adapter, power up in 80 column mode.
MONO Monochrome adapter, includes high resolution

monochrome adapters.

HALT ON:

This category allows user to choose whether the computer will stop if an error
is detected during power up. Available options are “All errors”, “No errors”,
“All, But keyboard”, “All, But Diskette”, and “All But Disk/Key”.

BASE MEMORY:

Displays the amount of conventional memory detected during boot up.

EXTENDED MEMORY:

Displays the amount of extended memory detected during boot up.

TOTAL MEMORY:

Displays the total memory available in the system.

Chapter 4 Award BIOS Setup

PPC-7365F USER′S MANUAL

Page: 4-7

HARD DISK ATTRIBUTES:

Type Cylinders Heads V-P comp LZone Sect Capacity

1 306 4 128 305 17 10
2 615 4 300 615 17 20
3 615 6 300 615 17 30
4 940 8 512 940 17 62
5 940 6 512 940 17 46
6 615 4 65535 615 17 20
7 642 8 256 511 17 30
8 733 5 65535 733 17 30

9 900 15 65535 901 17 112
10 820 3 65535 820 17 20
11 855 5 65535 855 17 35
12 855 7 65535 855 17 49
13 306 8 128 319 17 20
14 733 7 65535 733 17 42
15 000 0 0000 000 00 00
16 612 4 0000 663 17 20
17 977 5 300 977 17 40
18 977 7 65535 977 17 56
19 1024 7 512 1023 17 59
20 733 5 300 732 17 30
21 733 7 300 732 17 42
22 733 5 300 733 17 30
23 306 4 0000 336 17 10
24 977 5 65535 976 17 40
25 1024 9 65535 1023 17 76
26 1224 7 65535 1223 17 71
27 1224 11 65535 1223 17 111
28 1224 15 65535 1223 17 152
29 1024 8 65535 1023 17 68
30 1024 11 65535 1023 17 93
31 918 11 65535 1023 17 83
32 925 9 65535 926 17 69
33 1024 10 65535 1023 17 85
34 1024 12 65535 1023 17 102
35 1024 13 65535 1023 17 110
36 1024 14 65535 1023 17 119
37 1024 2 65535 1023 17 17
38 1024 16 65535 1023 17 136
39 918 15 65535 1023 17 114
40 820 6 65535 820 17 40
41 1024 5 65535 1023 17 42
42 1024 5 65535 1023 26 65
43 809 6 65535 852 17 40
44 809 6 65535 852 26 61
45 776 8 65335 775 33 100

47 AUTO

Award Hard Disk Type Table

Chapter 4 Award BIOS Setup

Page: 4-8

PPC-7365F USER

′

S MANUAL

4-4. THE ADVANCED BIOS FEATURES

Choose the〝ADVANCED BIOS FEATURES〞in the main menu, the screen
shown as below.

Phoenix - AwardBIOS CMOS Setup Utility

Advanced BIOS Features

Virus Warning

CPU Internal Cache

External Cache

CPU L2 Cache ECC Checking

[Disabled]
[Enabled]
[Enabled]
[Enabled]

Item Help

Quick Power On Self Test

First Boot Device

Second Boot Device

Third Boot Device

Boot Other Device

Swap Floppy Drive

Boot Up Floppy Seek

Boot Up NumLock Status

Gate A20 Option

Typematic Rate Setting

X Typematic Rate (Chars/Sec)
X Typematic Delay (Msec)

Security Option

OS Select for DRAM > 64MB

Video BIOS Shadow

C8000-CBFFF Shadow

CC000-CFFFF Shadow

D0000-D3FFF Shadow

D4000-D7FFF Shadow

D8000-DBFFF Shadow

DC000-DFFFF Shadow

Small Logo (EPA) Show

[Enabled]
[USB-FDD]
[CDROM]
[Floppy]
[Enabled]
[Disabled]
[Disabled]
[On]
[Fast]
[Disabled]
6
250
[Setup]
[Non-OS2]
[Enabled]
[Disabled]
[Disabled]
[Disabled]
[Disabled]
[Disabled]
[Disabled]
[Enabled]

Menu Level ►

↑↓→←:Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5: Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults

BIOS Features Setup Menu

The “BIOS FEATURES SETUP” allow you to configure your system for
basic operation. The user can select the system’s default speed, boot-up
sequence, keyboard operation, shadowing and security.

Chapter 4 Award BIOS Setup

PPC-7365F USER′S MANUAL

Page: 4-9

A brief introduction of each setting in the BIOS FEATURES SETUP
program is given on the next few pages.

VIRUS WARNING :

This item allows you to choose the Virus Warning feature for IDE Hard Disk
boot sector protection. If this function is enabled and someone attempt to
write data into this area, BIOS will show a warning message on screen and
alarm beep.

CPU INTERNAL CACHE:
EXTERNAL CACHE:

These two categories speed up memory access. However, it depends on
CPU/chipset design.

CPU L2 CACHE ECC CHECKING:

When you select Enabled, memory checking is enable when the external
Cache contains ECC SRAMs.

QUICK POWER ON SELF-TEST:

This item allows you to speed up Power On Self Test (POST) after power-up
the computer. When enabled, the BIOS will shorten or skip some check items
during POST.

FIRST/SECOND/THIRD/OTHER BOOT DEVICE:

The BIOS attempt to load the operating system from the devices in the
sequence selected in these items.

SWAP FLOOPY DRIVE:

This field is effective only in systems with two floppy drives. Selecting
Enabled assigns physical drive B to logical drive A, and physical drive A to
logical drive B.

BOOT UP FLOPPY SEEK:

You may enable / disable this item to define whether the system will look for
a floppy disk drive to boot at power-on, or proceed directly to the hard disk
drive.

BOOT UP NUMLOCK STATUS:

Select power on state for NumLock.

GATE 20A OPTION:

Chapter 4 Award BIOS Setup

Page: 4-10

PPC-7365F USER

′

S MANUAL

This entry allows you to select how the gate A20 is handled. When Normal
was set, a pin in the keyboard controller controls Gate A20. And when Fast
was set, the chipset controls Gate A20.

TYPEMATIC RATE SETTING:

Enable this item if you wish to be able to configure the characteristics of
your keyboard. Typematic refers to the way in which characters are entered
repeatedly if a key is held down. For example, if you press and hold down
the "A" key, the letter "a" will repeatedly appear on your screen on your
screen until you release the key. When enabled, the typematic rate and
typematic delay can be selected.

TYPEMATIC RATE (CHARS/SEC):

This item sets the number of times a second to repeat a key stroke when you
hold the key down.

TYPEMATIC DELAY (MSEC):

The item sets the delay time after the key is held down before it begins to
repeat the keystroke.

SECURITY OPTION:

This category allows you to limit access to the system and Setup, or just to
Setup.

System The system will not boot and access to Setup will be

denied if the correct password is not entered at the
prompt.

Setup The system will boot, but access to Setup will be

denied if the correct password is not entered at the
prompt.

 To disable security, select PASSWORD SETTING at Main Menu and

then you will be asked to enter password. Do not type anything and just
press <Enter>, it will disable security. Once the security is disabled, the
system will boot and you can enter Setup freely.

OS SELECT FOR DRAM >64MB :

Select the operating system that is running with greater than 64MB or RAM
on the system. You may choose OS2 or Non-OS2.

Chapter 4 Award BIOS Setup

PPC-7365F USER′S MANUAL

Page: 4-11

VIDEO BIOS SHADOW:

Determines whether video BIOS will be coped to RAM. However, it is
optional depending on chipset design. Video Shadow will increase the
video speed.

4-5. ADVANCED CHIPSET FEATURES

Choose the〝ADVANCED CHIPSET FEATURES〞from the main menu,

the screen shown as below.

Phoenix - AwardBIOS CMOS Setup Utility

Advanced Chipset Features

Item Help

DRAM Timing Selectable
X DRAM Clock
X SDRAM Cycle Length
X Bank Interleave
Memory Hole
P2C/C2P Concurrency
System BIOS Cacheable

Video RAM Cacheable

Frame Buffer Size

Panel Controlled By
X Panel Resolution
Boot Device Select
OnChip USB
USB Keyboard Support
OnChip Sound

CPU to PCI Write Buffer
PCI Dynamic Bursting
PCI Master 0 WS Write
PCI Delay Transaction
PCI#2 Access #1 Retry

[Enabled]
Host CLK
3
Disabled
[Disabled]
[Enabled]
[Disabled]
[Disabled]
[16M]
[Hardware Settings]
800 x 600
[Auto]
[Enabled]
[Disabled]
[Auto]
[Enabled]
[Enabled]
[Enabled]
[Disabled]
[Enabled]

Menu Level ►

↑↓→←:Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5: Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults

Chipset Features Setup Screen

Chapter 4 Award BIOS Setup

Page: 4-12

PPC-7365F USER

′

S MANUAL

This parameter allows you to configure the system based on the specific
features of the installed chipset. The chipset manages bus speed and
access to system memory resources, such as DRAM and the external cache.

It also coordinates communications between conventional ISA bus and the
PCI bus. It must be stated that these items should never need to be altered.
The default settings have been chosen because they provide the best opera­ting conditions for the system. The only time you might consider making
any changes would be if you discovered that data was being lost while
using your system.

 Please be aware that if select the wrong panel type, it may cause the

abnormal display of the LCD.

DRAM TIMING SELECTABLE :

The value in this field depends on performance parameters of the installed
memory chips (DRAM). Do not change the value from the factory setting
unless you install new memory that has a different performance rating than
the original DRAMs.

DRAM CLOCK :

This item allows you to control the DRAM speed at either equal to or one­half of the SYSCLK (system clock signal) speed. While speed is always
desirable, choosing the higher setting may prove to be too fast for some
components.

SDRAM CYCLE LENGTH:

When synchronous DRAM is installed, the number of clock cycles of CAS
latency depends on the DRAM timing. Do not reset this field from the
default value specified by the system designer.

MEMORY HOLE:

In order to improve performance, certain space in memory is reserved for ISA
cards. This memory must be mapped into the memory space below 16MB.

P2C/C2P CONCURRENCY:

This item allows you to enable/ disable the PCI to CPU, CPU to PCI
concurrency.

Chapter 4 Award BIOS Setup

PPC-7365F USER′S MANUAL

Page: 4-13

SYSTEM BIOS CACHEABLE:

Selecting Enabled allows caching of the system BIOS ROM at F0000h­FFFFFh, resulting in better system performance. However, if any program
writes to this memory area, a system error may result.

VIDEO RAM CACHEABLE:

Selecting Enabled allows caching of the video BIOS ROM at C0000h to
C7FFFh, resulting in better video performance. However, if any program
writes to this memory area, a system error may result.

VIDEO BIOS CACHEABLE:

Select Enabled allows caching of the video BIOS, resulting in better system
performance. However, if any program writes to this memory area, a system
error may result.

ONCHIP USB :

This should be enabled if your system has a USB installed on the system
board and you want to use it. Even when so equipped, if you add a higher
performance controller, you will need to disable this feature.

USB KEYBOARD SUPPORT :

Select Enabled if your system contains a Universal Serial Bus (USB)

controller and you have a USB keyboard.

ONCHIP SOUND :

This item allows you to control the onboard AC 97 audio.

CPU TO PCI WRITE BUFFER :

When this field is Enabled, writes from the CPU to the PCI bus are buffered,

to compensate for the speed differences between the CPU and the PCI bus.

When Disabled, the writes are not buffered and the CPU must wait until the

write is complete before starting another write cycle.

PCI DYNAMIC BURSING :

When Enabled, every write transaction goes to the write buffer. Burstable

transactions then burst on the PCI bus and nonburstable transactions don’t.

PCI MASTER 0 WS WRITE :

When Enabled, writes to the PCI bus are executed with zero wait states.

Chapter 4 Award BIOS Setup

Page: 4-14

PPC-7365F USER

′

S MANUAL

PCI DELAY TRANSACTION :

The chipset has an embedded 32-bit posted write buffer to support delay

transactions cycles. Select Enabled to support compliance with PCI

specification version 2.1.

PCI#2 ACCESS #1 RETRY :

When disabled, PCI#2 will not be disconnected until access finishes (default).
When enabled, PCI#2 will be disconnected if max retries are attempted

without success.

Chapter 4 Award BIOS Setup

PPC-7365F USER′S MANUAL

Page: 4-15

4-6. INTEGRATED PERIPHERALS

Choose〝INTEGRATED PERIPHERALS〞from the main setup menu, a
display will be shown on screen as below:

Phoenix – Award CMOS Setup Utility

Integrated Peripherals

Item Help

OnChip IDE Channel0
OnChip IDE Channel1
IDE Prefetch Mode
Primary Master PIO
Primary Slave PIO
Secondary Master PIO
Secondary Slave PIO
Primary Master UDMA
Primary Slave UDMA
Secondary Master UDMA
Secondary Slave UDMA
Init Display First
IDE HDD Block Mode

Onboard FDC Controller
Onboard Serial Port 1
Onboard Serial Port 2
Onboard Parallel Port
Onboard Parallel Mode
X ECP Mode Use DMA

X Parallel Port EPP Type

Onboard Parallel Port 3
Serial Port 3 Use IRQ
Onboard Serial Port 4
Serial Port 4 Use IRQ
IO Channel Check NMI
Watch Dog Timer Select

[Enabled]
[Enabled]
[Enabled]
[Auto]
[Auto]
[Auto]
[Auto]
[Auto]
[Auto]
[Auto]
[Auto]
[Onboard VGA]
[Enabled]
[Enabled]
[3F8/IRQ4]
[2F8/IRQ3]
[378/IRQ7]
[Normal]
3
EPP1.9
[3E8]
[IRQ10]
[2E8]
[IRQ11]
[Disabled]
[Disabled]

Menu Level

►

↑↓→←:Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5: Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults

Integrated Peripherals Setup Screen

By moving the cursor to the desired selection and by pressing the <F1> key,
the all options for the desired selection will be displayed for choice.

Chapter 4 Award BIOS Setup

Page: 4-16

PPC-7365F USER

′

S MANUAL

ONCHIP IDE CHANNEL 0 / 1 :

The chipset contains a PCI IDE interface with support for two IDE
channels. Select Enabled to activate the secondary IDE interface. Select
Disabled to deactivate this interface.

IDE PREFETCH MODE :

The onboard IDE drive interfaces supports IDE pre-fetching for faster drive
accesses. If you install a primary and or secondary add-in IDE interface,

set this field to Disabled if the interface does not support pre-fetching.

PRIMARY MASTER/SLAVE PIO:
SECONDARY MASTER/SLAVE PIO:

The four IDE PIO fields allow you to set a PIO mode (0-4) for each of the
four IDE devices that the onboard IDE interface supports. Modes 0 through
4 provide successively increased performance. In Auto mode, the system
automatically determines the best mode for each device.

PRIMARY MASTER/SLAVE UDMA:
SECONDARY MASTER/SLAVE UDMA:

Ultra DMA/33 implementation is possible only if your IDE hard drive
supports it and the operating environment includes a DMA driver (Windows
95 OSR2 or a third-party IDE bus master driver). If you hard drive and your
system software both support Ultra DMA/33, select Auto to enable BIOS
support.

INIT DISPLAY FIRST:

This item allows you to decide to active whether PCI Slot or on-chip VGA
first.

IDE HDD BLOCK MODE :

Block mode is also called block transfer, multiple commands, or multiple
sector read/write. If your IDE hard drive supports block mode (most new
drives do), select Enabled for automatic detection of the optimal number of
block read/writes per sector the drive can support.

ONBOARD FDD CONTROLLER:

Select Enabled if the system has a floppy disk drive (FDD) installed on the
system board and you wish to use it. If you install and-in FDD or the system
has no floppy drive, select Disabled.

Chapter 4 Award BIOS Setup

PPC-7365F USER′S MANUAL

Page: 4-17

ONBOARD SERIAL PORT 1:
ONBOARD SERIAL PORT 2:
ONBOARD SERIAL PORT 3:
ONBOARD SERIAL PORT4:

Select an address and corresponding interrupt for the first and second serial
ports.

ONBOARD PARALLEL PORT:

This item allows you to determine access onboard parallel port controller with
which I/O address.

PARALLEL PORT MODE:

Select an operating mode for the onboard parallel (printer) port. Select

Normal, Compatible, or SPP unless you are certain your hardware and

software both support one of the other available modes.

ECP MODE USE DMA:

Select a DMA channel for the parallel port for use during ECP mode.

PARALLEL PORT EPP MODE:

Select EPP port type 1.7 or 1.9.

IO CHANNELCHECK NMI :

This field allows you to enable or disable IO channel check NMI. Before
selecting this function, the user should check first that NMI function is enabled as

described in chapter 2 (Reset/NMI/Clear Watchdog Selection).

Chapter 4 Award BIOS Setup

Page: 4-18

PPC-7365F USER

′

S MANUAL

4-7. POWER MANAGEMENT SETUP

Choose〝POWER MANAGEMENT SETUP〞option on the main menu, a
display will be shown on screen as below :

Phoenix - AwardBIOS CMOS Setup Utility

Power Management Setup

Item Help

ACPI Function
►Power Management
PM Control by APM

Video Off Option

Video Off Method

MODEM Use IRQ

Soft-Off by PWRBTN

State After Power Failure
► Wake Up Events

[Enabled]
[Press Enter]
[Yes]
[Suspend -> Off]
[V/H SYNC+Blank]
[3]
[Instant - Off]
[Off]
[Press Enter]

Menu Level ►

↑↓→←:Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5: Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults

Power Management Setup Screen

The “Power Management Setup” allows the user to configure the system to
the most effectively save energy while operating in a manner consistent with
your own style of computer use.

ACPI FUNCTION:

Users are allowed to enable or disable the Advanced Configuration and
Power Management (ACPI).

POWER MANAGEMENT:

This item allows you to select the Power Management mode.

PM CONTROL BY APM:

When enabled, an Advanced Power Management device will be activated to
enhance the Max. Power Saving mode and stop the CPU internal clock. If
Advance Power Management (APM) is installed on your system, selecting
Yes gives better power savings. If the Max. Power Saving is not enabled, this

will be preset to No.

Chapter 4 Award BIOS Setup

PPC-7365F USER′S MANUAL

Page: 4-19

VIDEO OFF OPTION:

When enabled, this feature allows the VGA adapter to operate in a power
saving mode.

Always On Monitor will remain on during power saving modes.
Suspend --> Off Monitor blanked when the systems enters the Suspend

mode.

Susp,Stby --> Off Monitor blanked when the system enters either Suspend or

Standby modes.

All Modes --> Off Monitor blanked when the system enters any power saving

mode.

VIDEO OFF METHOD:

This determines the manner in which the monitor is blanked.

V/H SYNC+Blank This selection will cause the system to turn off the vertical

and horizontal synchronization ports and write blanks to the
video buffer.

Blank Screen This option only writes blanks to the video buffer.

DPMS Select this option if your monitor supports the Display

Power Management Signalling (DPMS) standard of the
Video Electronics Standards to select video power
management values.

MODEM USE IRQ:

This determines the IRQ in which the MODEM can use.

SOFT-OFF BY PWR-BTTN:

Pressing the power button for more than 4 seconds forces the system to
enter the Soft-Off state when the system has “hung”. The choices are
Delay 4 Sec and Instant-Off.

PM EVENTS:

PM events are I/O events whose occurrence can prevent the system from
entering a power saving mode or can awaken the system from such a mode.
In effect, the system remains alert for anything, which occurs to a device

which is configured as Enabled, even when the system is in a power down
mode. (1) Primary IDE 0 (2) Primary IDE 1 (3) Secondary IDE 0 (4)
Secondary IDE 1 (5) FDD, COM, LPT Port

Chapter 4 Award BIOS Setup

Page: 4-20

PPC-7365F USER

′

S MANUAL

4-8. PNP/PCI CONFIGURATION

Choose 〝PNP/PCI CONFIGURATION〞 from the main menu, a display
will be shown on screen as below:

Phoenix - AwardBIOS CMOS Setup Utility

PnP/PCI Configurations

PNP OS Installed

Reset Configuration Data

[No]
[Disabled]

Item Help

Resources Controlled By

x IRQ Resources
x DMA Resources

PCI/VGA Palette Snoop

Assign IRQ for VGA

Assign IRQ for USB

[Auto(ESCD)]

Press Enter
Press Enter

[Disabled]
[Enabled]
[Enabled]

Menu Level ►

Select Yes if you are
using a Plug and Play
capable operating
system Select No if
you need the BIOS to
configure non-boot
devices

↑↓→←:Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5: Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults

PNP/PCI Configuration Setup Screen

0 Note: Please change IRQ 15 to Legacy ISA before installing Windows 98.

This section describes how to configure PCI bus system. PCI, also known as
Personal Computer Interconnect, is a system, which allows I/O devices to
operate at speeds nearing the speed of the CPU itself uses when communica­ting with its own special components. This section covers technical items,
which is strongly recommended for experienced users only.

PNP OS INSTALLED:

This item allows you to determine install PnP OS or not.

Chapter 4 Award BIOS Setup

PPC-7365F USER′S MANUAL

Page: 4-21

RESET CONFIGURATION DATA:

Normally, you leave this field Disabled. Select Enabled to reset Extended
System Configuration Data (ESCD) when you exit Setup if you have
installed a new add-on and the system configuration has caused such a
serious conflict that the operating system cannot boot.

RESOURCE CONTROLLED BY:

The Award Plug and Play Bios can automatically configure all of the booth
and Plug and Play-compatible devices. However, this capability means
absolutely nothing unless you are using a Plug and Play operating system
such as Windows 95. By choosing “manual”, you are allowed to

configure the IRQ Resources, DMA Resources and Memory Resources.

The choices are Auto (ESCD) and Manual.

IRQ RESOURCES:

You may assign each system interrupt a type, depending on the type of
device using the interrupt.

DMA RESOURCES:

When resources are controlled manually, assign each system DMA channel
a type, depending on the type of device using the DMA channel.

PCI/VGA PALETTE SNOOP:

Leave this field at disabled.

ASSIGN IRQ FOR USB:

Enable or Disable to assign IRQ for USB.

ASSIGN IRQ FOR VGA:

Enable or Disable to assign IRQ for VGA.

Chapter 4 Award BIOS Setup

Page: 4-22

PPC-7365F USER

′

S MANUAL

4-9. PC HEALTH STATUS

Choose 〝PC HEALTH STATUS〞 from the main menu, a display will
be shown on screen as below:

Phoenix - AwardBIOS CMOS Setup Utility

PC Health Status

Item Help CPU Warning Temperature
Current CPU Temp.
Current System Fan Speed
VCORE

2.5V

3.3V
5 V
12V

[Disabled]
44°C/111°F
6012 RPM

1. 09V

2. 2.56V

3.46V

5.32V

12.60V

Menu Level ►

↑↓→←:Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5: Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults

PC Health Status Setup Screen

The setup menu allows you to select whether to choose between monitoring or
ignoring the hardware monitoring function of your system.

CPU WARNING TEMERATURE:

This item will prevent CPU from overheating.

CPU TEMPERATURE:

This item shows you the current CPU temperature.

SYSTEM FAN SPEED:

This item shows you the current SYSTEMFAN speed.

VCORE:

This item shows you the current system voltage.

2.5V/3.3V/5V/12V:

This item shows you the voltage of +3.3V/+5V/+12V/-12V/-5V.

Chapter 4 Award BIOS Setup

PPC-7365F USER′S MANUAL

Page: 4-23

4-10. FREQUENCY/VOLTAGE CONTROL

Choose 〝FREQUENCY/VOLTAGE CONTROL〞 from the main menu,
a display will be shown on screen as below:

Phoenix - AwardBIOS CMOS Setup Utility

Frequency/Voltage Control

Item Help

VIA C3 Clock Ratio

Auto Detect DIMM/PCI Clk
Spread Spectrum

[Default]

[Enabled]
[Disabled]

Menu Level ►

↑↓→←:Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5: Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults

Frequency / Voltage Control Setup Screen

This setup menu allows you to specify your settings for frequency/voltage
control.

AUTO DETECT PCI CLK:

This item allows you to enable or disable auto detect PCI Clock.

SPREAD SPECTRUM:

This item allows you to enable or disable the spread spectrum modulate.

Chapter 4 Award BIOS Setup

Page: 4-24

PPC-7365F USER

′

S MANUAL

4-11. LOAD FAIL-SAFE DEFAULTS

By pressing the <ENTER> key on this item, you get a confirmation dialog
box with a message similar to the following:

Load Fail-Safe Defaults ( Y/N ) ? N

To use the BIOS default values, change the prompt to "Y" and press the
<Enter > key. CMOS is loaded automatically when you power up the
system.

 Please be aware that if select the wrong panel type, it may cause the abnormal

display of the LCD.

4-12. LOAD OPTIMIZED DEFAULTS

When you press <Enter> on this category, you get a confirmation dialog
box with a message similar to the following:

Load Optimized Defaults ( Y/N ) ? N

Pressing "Y" loads the default values that are factory setting for optimal
performance system operations.

 Please be aware that if select the wrong panel type, it may cause the abnormal

display of the LCD.

Chapter 4 Award BIOS Setup

PPC-7365F USER′S MANUAL

Page: 4-25

4-13. PASSWORD SETTING

User is allowed to set either supervisor or user password, or both of them.
The difference is that the supervisor password can enter and change the
options of the setup menus while the user password can enter only but do not
have the authority to change the options of the setup menus.

TO SET A PASSWORD

When you select this function, the following message will appear at the
center of the screen to assist you in creating a password.

Enter Password:

Type the password up to eight characters in length, and press < Enter >.
The password typed now will clear any previously entered password from
CMOS memory. You will be asked to confirm the password. Type the
password again and press the < Enter > key. You may also press < Esc >
to abort the selection and not enter a password.

 User should bear in mind that when a password is set, you will be

asked to enter the password everything you enter CMOS setup Menu.

TO DISABLE THE PASSWORD

To disable the password, select this function (do not enter any key when
you are prompt to enter a password), and press the <Enter> key and a
message will appear at the center of the screen:

PASSWORD DISABLED!!!

Press any key to continue...

Press the < Enter > key again and the password will be disabled. Once the
password is disabled, you can enter Setup freely.

Chapter 4 Award BIOS Setup

Page: 4-26

PPC-7365F USER

′

S MANUAL

4-14. SAVE & EXIT SETUP

After you have completed adjusting all the settings as required, you must
remember to save these setting into the CMOS RAM. To save the settings,
select “SAVE & EXIT SETUP” and press <Enter>, a display will be shown
as follows:

Phoenix - AwardBIOS CMOS Setup Utility

►Standard CMOS Features

►Advanced BIOS Features

►Advanced Chipset Features

►Integrated Peripherals

►Power Management

►PnP/PCI Configura

►PC Health Status

►Frequency/Voltage Control

Load Fail-Safe Defaults

Load Optimized Defaults

Set Supervisor Password

word

etup

Saving

Esc : Quit F9 : Menu in BIOS ↑↓→← : Select Item
F10 : Save & Exit Setup

Save Data to CMOS

When you confirm that you wish to save the settings, your system will be
automatically restarted and the changes you have made will be implemented.
You may always call up the setup program at any time to adjust any of the
individual items by pressing the <Del> key during boot up.

Save to CMOS and EXIT Y/N)? Y

Chapter 4 Award BIOS Setup

PPC-7365F USER′S MANUAL

Page: 4-27

4-15. EXIT WITHOUT SAVING

If you wish to cancel any changes you have made, you may select the
“EXIT WITHOUT SAVING” and the original setting stored in the CMOS
will be retained. The screen will be shown as below:

Phoenix - AwardBIOS CMOS Setup Utility

►Standard CMOS Features

►Advanced BIOS Features

►Advanced Chipset Features

►Integrated Peripherals

►Power Management

►PnP/PCI Configura

►PC Health Status

►Frequency/Voltage Control

Load Fail-Safe Defaults

Load Optimized Defaults

Set Supervisor Password

word

etup

Saving

Esc : Quit F9 : Menu in BIOS ↑↓→← : Select Item
F10 : Save & Exit Setup

Abandon all Datas

Quit Without Saving (Y/N)? N

Page: A-1

SYSTEM
ASSEMBLY

This appendix contain exploded diagram of the system.
Section includes:

z Exploded Diagram for HDD Assembly

z Exploded Diagram for Wall Mounting

z Exploded Diagram for VESA ARM

APPENDIX

A

Appendix A System Assembly

Page: A-2

PPC-7365F USER

′

S MANUAL

EXPLODED DIAGRAM FOR HDD ASSEMBLY

EC-8150A-HD-HOLDER

EC-8150A-HD-AGA-R

EC-8150A-HD-AGA-L
EC-8150A-HD-SHK

SA-SILI-RUBBER

QWS-2.7-8-1

QSTUD-2.5-6-R

20-029-03001029

HML-95-68.85-0.125

SLIM HDD

QSTUD-3-0.5-6-SP-W
QSTUD-UNC-N06-32-FLAT

PS-8150A HDD HOLDER

PS-8150A HDD SHOCH AGAINST RIGHT SIDE

PS-8150A HDD SHOCH AGAINST LEFT SIDE
PS-8150A HDD SHOCK AGAINST

RUBBER (Si 22 green) Dia 11.5x11.5Hx3.5

WASHER 2.7 x 8 x1 WASHER

M2.5x6(ROUND_HEAD) SCREW

PPC-7365(F) 2.5IN HDD HOLDER

MYLAY (95x68.85x0.125mm) FOR PS-8830 SLIM HDD

M3xP0.5L=6
UNC-N06-32-FLAT (No6-32 UNC FLAT L=6.4)

1

2

3
4

5

6

7

8

9

10

11
12

1

1

1

1

1

4

4

4

4

4
4

NO

PART NO

DESCRIPTION

Q'TY REMARKS

11

11

8

9

10

12

12

4

5

6

7

2

3

1

Appendix A System Assembly

PPC-7365F USER′S MANUAL

Page: A-3

EXPLODED DIAGRAM FOR WALL MOUNTING

STEP 1:

EC-8150A-HOOK-SHEET

QSTUD-3-0.5-6-F-B

PS-8150A CASE HOOK SHEET

Screw M3 x 0.5P x 6 FLAT Black

DESCRIPTIONPART NONO
1
2

Q'TY

4
4

REMARKS

2

1

1

2

1

2

2

1

Appendix A System Assembly

Page: A-4

PPC-7365F USER

′

S MANUAL

STEP 2:

Wall

3

7

4

.

2

m

m

2

7

1

.

2
m
m

Appendix A System Assembly

PPC-7365F USER′S MANUAL

Page: A-5

STEP 3:

WALL

1

3

2

1

3

2

1

3

2

1

3

2

NO PART NO

DESCRIPTION

Q'TY REMARKS

4

4

4

M4 HOOK
Screw M4 x 0.7P x 35mm
Screw hat M4 x 0.7P x 3mm

EC-M4-HOOK
QSTUD-4-0.7-35-R-N
QSTUD-4-0.7-NIL

1
2
3

Appendix A System Assembly

Page: A-6

PPC-7365F USER

′

S MANUAL

STEP 4, 5 & 6:

M4 SCREW

HOOK

M4 NUT

WALL

STEP 4

STEP 5

STEP 6

WALL

M4 NUT

M4 NUT

M4 SCREW

HOOK

WALL

(IF NEED)

Appendix A System Assembly

PPC-7365F USER′S MANUAL

Page: A-7

EXPLODED DIAGRAM FOR VESA ARM

EC-8150A-W-STD

QSTUD-4-0.7-6-F-B

PART NO

NO

1
2

DESCRIPTION

8150A-WALL-MOUNT

Screw M4-P0.7-L6 FLAT Black

Q'TY

1
5

REMARKS

2

1

2

2

Page: B-1

TECHNICAL
SUMMARY

This section introduce you the maps concisely.

Sections include:

z Block Diagram

z Interrupt Map

z RTC (Standard) RAM Bank

z Timer & DMA Channels Map

z I / O & Memory Map

APPENDIX

B

Appendix B Technical Summary

Page: B-2

PPC-7365F USER

′

S MANUAL

BLOCK DIAGRAM

Appendix B Technical Summary

PPC-7365F USER′S MANUAL

Page: B-3

INTERRUPT MAP

IRQ ASSIGNMENT

0 System TIMER interrupt from TIMER-0
1 Keyboard output buffer full
2 Cascade for IRQ 8-15
3 Serial port 2
4 Serial port 1
5 Available
6 Floppy Disk adapter
7 Parallel port 1
8 RTC clock

9 ACPI-Compliant System
10 Serial port 3
11 Serial port 4
12 PS/2 Mouse
13 Math coprocessor
14 Hard Disk adapter
15 Hard Disk adapter

Appendix B Technical Summary

Page: B-4

PPC-7365F USER

′

S MANUAL

RTC (STANDARD) RAM BANK

CODE ASSIGNMENT

00h Seconds
01h Second alarm
02h Minutes
03h Minutes alarm
04h Hours
05h Hours alarm
06h Day of week
07h Day of month
08h Month

09h Year
0Ah Status register A
0Bh Status register B
0Ch Status register C
0Dh Status register D

0Eh-7Fh 114 Bytes of User RAM

Appendix B Technical Summary

PPC-7365F USER′S MANUAL

Page: B-5

TIMER & DMA CHANNELS MAP

Timer Channel Map

:

Timer Channel Assignment

0 System timer interrupt
1 DRAM Refresh request
2 Speaker tone generator

DMA Channel Map

:

DMA Channel Assignment

0 Available
1 Available
2 Floppy Disk adapter
3 Available
4 Cascade
5 Available
6 Available
7 Available

Appendix B Technical Summary

Page: B-6

PPC-7365F USER

′

S MANUAL

I/O & MEMORY MAP

Fixed I/O Ranges Decoded by ICH2

:

I/O Address Read Target Write Target Internal Unit

00h-08h DMA Controller DMA Controller DMA
09h-0Eh Reserved DMA Controller DMA
0Fh DMA Controller DMA Controller DMA
10h-18h DMA Controller DMA Controller DMA
19h-1Eh Reserved DMA Controller DMA
1Fh DMA Controller DMA Controller DMA
20h-21h Interrupt Controller Interrupt Controller Interrupt
24h-25h Interrupt Controller Interrupt Controller Interrupt
28h-29h Interrupt Controller Interrupt Controller Interrupt
2Ch-2Dh Interrupt Controller Interrupt Controller Interrupt
2Eh-2Fh LPC SIO LPC SIO Forwarder to LPC
30h-31h Interrupt Controller Interrupt Controller Interrupt
34h-35h Interrupt Controller Interrupt Controller Interrupt
38h-39h Interrupt Controller Interrupt Controller Interrupt
3Ch-3Dh Interrupt Controller Interrupt Controller Interrupt
40h-42h Timer/Counter Timer/Counter PIT (8254)
43h Reserved Timer/Counter PIT
4E-4F LPC SIO LPC SIO Forwarder to LPC
50h-52h Timer/Counter Timer/Counter PIT
53h Reserved Timer/Counter PIT
60h Microcontroller Microcontroller Forwarder to LPC
61h NMI Controller NMI Controller Processor I/F
62h Microcontroller Microcontroller Forwarder to LPC
63h NMI Controller NMI Controller Processor I/F
64h Microcontroller Microcontroller Forwarder to LPC
65h NMI Controller NMI Controller Processor I/F
66h Microcontroller Microcontroller Forwarder to LPC
67h NMI Controller NMI Controller Processor I/F
70h Reserved5 NMI & RTC controller RTC
71h RTC Controller RTC Controller RTC
72h RTC Controller NMI & RTC controller RTC
73h RTC Controller RTC Controller RTC
74h RTC Controller NMI & RTC controller RTC
75h RTC Controller RTC Controller RTC
76h RTC Controller NMI & RTC controller RTC
77h RTC Controller RTC Controller RTC