Protech Systems PMB-881LF, PMB-881LF M2, PMB-871LF User Manual

USER’S MANUAL
PMB-881LF
Intel® Sandy Bridge Xeon E3/Core i3 CPU ATX Motherboard With VGA/Sound/2LAN
P
MB
-881LF
M
2
Copyright Notice
PMB-881LF Intel® Xeon E3/Core i3
ATX Motherboard
With VGA/ Sound/ 2LAN
COPYRIGHT NOTICE
This operation manual is meant to assist users in installing and setting up the system. The information contained in this document is subject to change without prior any notice.
This manual is copyrighted September 2011. You may not reproduce or transmit in any form or by any means, electronic, or mechanical, including photocopying and recording.
ACKNOWLEDGEMENTS
All trademarks and registered trademarks mentioned herein are the property of their respective owners.
CE NOTICE
This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
Copyright Notice
FCC NOTICE
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
You are cautioned that any change or modifications to the equipment not expressly approve by the party responsible for compliance could void your authority to operate such equipment.
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer’s instructions.
Installation only by a trained electrician or only by an electrically trained person who
knows all English Installation and Device Specifications which are to be applied.
Contents
TABLE OF CONTENTS
CHAPTER 1 INTRODUCTION
1-1 About This Manual .................................................... 1-2
1-2 System Specifications ................................................. 1-3
1-3 Safety Precautions ...................................................... 1-6
CHAPTER 2 SYSTEM CONFIGURATION
2-1 Jumper & Connector Quick Reference Table ............... 2-2
2-2 Component Locations ................................................... 2-3
2-3 How to Set the Jumpers ................................................ 2-4
2-4 COM Port Connector ……..………………………….. 2-6
2-5 COM3 RI & Voltage Selection …………….........…… 2-8
2-6 COM4 RI & Voltage Selection …………….........…… 2-9
2-7 RS232/422/485(COM2) Selection ................................ 2-10
2-8 COM2 Auto Detect Selection ……..………………… 2-11
2-9 Keyboard and PS/2 Mouse Connector .......................... 2-12
2-10 Reset Connector ............................................................ 2-12
2-11 Hard Disk Drive LED Connector .................................. 2-13
2-12 ATX Power Button …................................................... 2-13
2-13 External Speaker Connector .......................................... 2-13
2-14 PLed Connector …….................................................... 2-14
2-15 Clear CMOS Data Selection ………………………… 2-14 2-16 CPU Fan Connector ………..………………………… 2-15 2-17 System Fan Connector ……………………………… 2-15 2-18 TPM Connector …………………………………….. 2-16 2-19 VGA Connector ………………………………………. 2-17 2-20 Serial ATA Connector ………………………………. 2-18 2-21 Printer Connector ……………………………………. 2-20 2-22 Universal Serial Bus Connector ……………………… 2-21 2-23 IrDA Connector ……..………………………..……… 2-23 2-24 USB & LAN Connector ……………………………. 2-24 2-25 Display Port Connector …………………………….. 2-26 2-26 Digital Input/Output Connector ……………………… 2-27 2-27 ATX Power Connector ………………………………. 2-28 2-28 Sound Connector …………….………………………. 2-29
Contents
CHAPTER 3 SOFTWARE UTILITIES
3-1 Introduction ................................................................ 3-2
3-2 Intel Chipset Software Installation Utility …..……... 3-3
3-3 VGA Driver Utility ..................................................... 3-4
3-4 LAN Driver Utility ..................................................... 3-5
3-5 Sound Driver Utility ................................................... 3-6
3-6 Intel ME Driver Utility ……………………………… 3-7
CHAPTER 4 AMI BIOS SETUP
4-1 Introduction ................................................................ 4-2
4-2 Entering Setup ........................................................... 4-4
4-3 Main ……................................................................... 4-6
4-4 Advanced …………………….........................…....... 4-7
4-5 Chipset ……………................................................... 4-40
4-6 Boot ..………………................................................. 4-49
4-7 Security …………………………………………….. 4-51 4-8 Save & Exit ………………………………………… 4-54
APPENDIX A EXPANSION BUS
PCI Bus Pin Assignment …………………………………….. A-2 Mini-PCIe Bus Pin Assignment ……………………………… A-3
APPENDIX B TECHNICAL SUMMARY
Block Diagram ...................................................................... B-2
Interrupt Map ........................................................................ B-3
DMA Channels Map ……..................................................... B-4
Memory Map .......................................................................... B-5
I/O Map .................................................................................. B-6
Watchdog Timer Configuration …………..………………. B-9 Flash BIOS Update …………………………………………. B-11
Page:1-1
INTRODUCTION
This chapter gives you the information for PMB-881LF. It also outlines the System specification.
Section includes:
About This Manual
System Specifications
Safety Precautions
Experienced users can skip to chapter 2 on page 2-1 for Quick Start.
CHAPTER
1
Chapter 1 Introduction
Page: 1-2
PMB-881LF USER′S MANUAL
1-1. ABOUT THIS MANUAL
Thank you for purchasing our PMB-881LF Intel® Xeon E3/Core i3 CPU ATX Motherboard with VGA / Sound / 2LAN, which is fully PC / AT compatible. PMB-881LF provides faster processing speed, greater expandability and can handle more task than before. This manual is designed to assist you how to install and set up the system. It contains four chapters. The user can apply this manual for configuration according to the following chapters:
Chapter 1 Introduction
This chapter introduces you to the background of this manual, and the specifications for this system. The final page of this chapter will indicate how to avoid damaging this board.
Chapter 2 Hardware Configuration
This chapter outlines the component locations and their functions. In the end of this chapter, you will learn how to set jumper and how to configure this card to meet your own needs.
Chapter 3 Software Utilities
This chapter contains helpful information for proper installations of the VGA utility, LAN utility, and Sound utility.
Chapter 4 AMI BIOS Setup
This chapter indicates you how to set up the BIOS configurations.
Appendix A Expansion Bus
This Appendix introduces you the PCI / Mini-PCIe expansion bus.
Appendix B Technical Summary
This section gives you the information about the Technical maps, Watchdog­timer configuration, and Flash BIOS Update.
Chapter 1 Introduction
PMB-881LF USER′S MANUAL
Page: 1-3
1-2. SYSTEM SPECIFICATION
CPU
Intel Xeon® E3 / CoreTM i3 / Pentium Sandy Bridge CPU
CHIPSET
Intel® C206
MEMORY
4 x 240pins DDR3 DIMM socket Dual channel DDR3-1333/1066MHz, supports ECC, non-ECC
 BIOS:
AMI BIOS (UEFI), with VGA BIOS
 REAL TIME CLOCK:
Build in PCH
 BUS SUPPORT:
4 x PCI, 1 x MiniPCIe, 2 x PCIe (4X), 1 x PCIe (16X)
 DISPLAY:
Build-in processor Supports VGA, 2 x Display port (Protech Display Port definition)
*
Discrete graphic card is necessary for display if the chosen CPU doesn’t have
integrated graphics support.
 SATA INTERFACE:
6 x S-ATA connector from PCH SATA1~2 support SATAIII (6.0Gb/s), SATA3~6 support SATAII (3.0Gb/s) Supports Raid 0/1/5/10
 SERIAL PORT:
4 ports, COM1/3/4 for RS-232, COM2 for RS-232/422/485 COM3/4 support output +5V or +12V, and use Jumper settings.
 USB CONNECTOR:
12 ports, support USB 2.0 4 ports on rear panel, 8 ports with box-header on board
Chapter 1 Introduction
Page: 1-4
PMB-881LF USER′S MANUAL
 LAN ADAPTER:
Dual ports, supports 10/100/1000Mbps LAN1: Intel 82579LM 1000BaseT PHY Ethernet LAN2: Intel 82583V 1000BaseT Ethernet Supports Wake-on-LAN
 SOUND:
High Definition Audio Realtek ALC888S Supports Line-in/Line-out/MIC x 1
 HARDWARE MONITORING FUNCTION:
Voltage, CPU Temperature and Cooling fan speed (CPU, System)
 IRDA PORT:
1 x IrDA port, supports v1.0 SIR protocol
 SPEAKER:
Internal buzzer
 TPM FUNCTION:
1 x 20pin header on board, supports TPM1.2
 PARALLEL PORT:
1 port, Bi-dircetion, SPP / EPP / ECP (D-SUB on edge)
 DIGITAL I/O:
8in/8out (API)
 LED INDICATOR:
1 x HDD LED, 1 x power LED
 KEYBOARD/MOUSE:
1 x PS/2 port (KB/MS), combined with mini DIN connector on rear panel
 WATCHDOG:
1~255sec.
Chapter 1 Introduction
PMB-881LF USER′S MANUAL
Page: 1-5
 POWER SUPPLY:
24pin ATX power supply
 DMA CONTROLLER:
2 x 82C37
 DMA CHANNELS:
7
 INTERRUPT CONTROLLERS:
2 x 82C59
 INTERRUPT LEVELS:
15
 TEMPERATURE:
Operation temperature 0°~60°C Storage temperature -40°~85°C
 HUMIDITY:
Operation humidity 0~95% Storage humidity 20~95%
 BOARD DIMENSIONS:
305mm x 244mm
 BOARD NET WEIGHT:
740gram
Chapter 1 Introduction
Page: 1-6
PMB-881LF USER′S MANUAL
1-3. SAFETY PRECAUTIONS
Follow the messages below to avoid your systems from damage:
1. Keep your system away from static electricity on all occasions.
2. Prevent electric shock. Don’t touch any components of this card when the card is power-on. Always disconnect power when the system is not in use.
3. Disconnect power when you change any hardware devices. For instance, when you connect a jumper or install any cards, a surge of power may damage the electronic components or the whole system.
Page 2-1
HARDWARE CONFIGURATION
** QUICK START **
CHAPTER
2
Helpful information describes the jumper & connector settings, and component locations.
Section includes:
Jumper & Connector Quick Reference Table
Component Locations
Configuration and Jumper settings
Connector’s Pin Assignments
Chapter 2 Hardware Configuration
Page: 2-2
PMB-881LF USER′S MANUAL
2-1. JUMPER & CONNECTOR QUICK REFERENCE TABLE
COM Port Connector ....................…..................……..
………………………………….
COM1, COM2 COM3, COM4
COM3 Port RI/Voltage Selection …………………….
JP11
COM4 Port RI/Voltage Selection …………………….
JP9
RS232/422/485 (COM2) Selection .....................……..
JP12
COM2 Auto Detect Selection ………………………….
JP10
Keyboard/Mouse Connector ..........….....………………
KB_MS1
Reset Connector .........................…....................………
FP1 (5, 7)
Hard Disk Drive LED Connector .......................………
FP1 (1, 3)
ATX Power Button …………………………………....
FP1 (9, 11)
External Speaker Connector ....…........................……..
FP1 (6, 8, 10, 12)
PLED Connector …………….…….……............…….
FP1 (2, 4)
Clear CMOS Data Selection …………………………..
JP6
CPU Fan Connector ……………………………………
CPU_FAN1
System Fan Connector …………………………………
SYS_FAN1
TPM Connector ………………………………………..
JLPC1
VGA Connector ………………………………………..
VGA1
Serial ATA Connector ………………………………… …………………………………
SATA1, SATA2, SATA3, SATA4, SATA5, SATA6
Printer Connector …….....................…………….........
LPT1
Universal Serial Bus Connector …….....................……
USB1, USB2, USB3, USBDOM1
IrDA Connector ………………………………………..
IR1
USB&LAN Connector …....................................……..
LAN1_USB1, LAN2_USB2
Display Port Connector ..………………………………
JDP1, JDP2
Digital Input/ Output Connector ……………………….
DIO1
ATX Power Connector …………………………………
ATX_PWR1
Sound Connector ………………………….……………
AUDIO1
Chapter 2 Hardware Configuration
PMB-881LF USER′S MANUAL
Page: 2-3
2-2. COMPONENT LOCATIONS
SIO
Intel
LGA 1155
Intel
PCH C206
ATX_PWR1
CPU_FAN1
PMB-881LF Connector, Jumper and Component locations
Chapter 2 Hardware Configuration
Page: 2-4
PMB-881LF USER′S MANUAL
2-3. HOW TO SET THE JUMPERS
You can configure your board by setting jumpers. Jumper is consists of two or three metal pins with a plastic base mounted on the card, and by using a small plastic "cap", Also known as the jumper cap (with a metal contact inside), you are able to connect the pins. So you can set-up your hardware configuration by "open" or "close" pins.
The jumper can be combined into sets that called jumper blocks. When the jumpers are all in the block, you have to put them together to set up the hardware configuration. The figure below shows how this looks like.
JUMPERS AND CAPS
If a jumper has three pins (for examples, labelled PIN1, PIN2, and PIN3), You can connect PIN1 & PIN2 to create one setting by shorting. You can either connect PIN2 & PIN3 to create another setting. The same jumper diagrams are applied all through this manual. The figure below shows what the manual diagrams look and what they represent.
Chapter 2 Hardware Configuration
PMB-881LF USER′S MANUAL
Page: 2-5
JUMPER DIAGRAMS
2 pin Jumper looks like this
Jumper Cap looks like this
3 pin Jumper looks like this
Jumper Block looks like this
JUMPER SETTINGS
Looks like this
3 pin Jumper
2-3 pin close(enabled)
Looks like this
Jumper Block
1-2 pin close(enabled)
2 pin Jumper close(enabled)
1
1
1
2
1 2
1
1
Looks like this
Chapter 2 Hardware Configuration
Page: 2-6
PMB-881LF USER′S MANUAL
2-4. COM PORT CONNECTOR
COM1: COM1 Connector COM1 is fixed as RS-232. The pin assignment is as follows:
PIN ASSIGNMENT
1 COM1_DCD# 2 COM1_RX 3 COM1_TX 4 COM1_DTR# 5 GND 6 COM1_DSR# 7 COM1_RTS# 8 COM1_CTS# 9 COM1_RI#
COM2: COM2 Connector The COM2 is selectable as RS-232/422/485. The pin assignment is as follows:
ASSIGNMENT
PIN
RS-232 RS-422
RS-485
1 COM2_DCD#
TX- TX­2 COM2_RX TX+ TX+ 3 COM2_TX RX+ RX+ 4 COM2_DTR#
RX- RX­5 GND GND GND 6 COM2_DSR#
RTS- GND
7 COM2_RTS#
RTS+ GND
8 COM2_CTS#
CTS+ GND
9 COM2_RI# CTS- GND
10 NC NC NC
COM2
Chapter 2 Hardware Configuration
PMB-881LF USER′S MANUAL
Page: 2-7
COM3: COM3 Connector COM3 is fixed as RS-232. The pin assignment is as follows:
PIN ASSIGNMENT
1 COM3_DCD# 2 COM3_RX 3 COM3_TX 4 COM3_DTR# 5 GND 6 COM3_DSR# 7 COM3_RTS# 8 COM3_CTS# 9 COM3_RI#
10 NC
COM4: COM4 Connector COM4 is fixed as RS-232. The pin assignment is as follows:
PIN ASSIGNMENT
1 COM4_DCD# 2 COM4_RX 3 COM4_TX 4 COM4_DTR# 5 GND 6 COM4_DSR# 7 COM4_RTS# 8 COM4_CTS# 9 COM4_RI#
10 NC
COM3
COM4
Chapter 2 Hardware Configuration
Page: 2-8
PMB-881LF USER′S MANUAL
2-5. COM3 RI & VOLTAGE SELECTION
JP11: COM3 RI & Voltage Selection The selections are as follows:
SELECTION
JUMPER
SETTINGS
JUMPER
ILLUSTRATION
5V
5-6
1
2
5
6
12V 3-4
1
2
5
6
RI 1-2
1
2
5
6
***Manufacturing Default -- RI.
Chapter 2 Hardware Configuration
PMB-881LF USER′S MANUAL
Page: 2-9
2-6. COM4 RI & VOLTAGE SELECTION
JP9: COM4 RI & Voltage Selection The selections are as follows:
SELECTION
JUMPER
SETTINGS
JUMPER
ILLUSTRATION
5V 5-6
1
2
5
6
12V 3-4
1
2
5
6
RI 1-2
1
2
5
6
***Manufacturing Default -- RI.
Chapter 2 Hardware Configuration
Page: 2-10
PMB-881LF USER′S MANUAL
2-7. RS232/422/485 (COM2) SELECTION
JP12: RS-232/422/485 (COM2) Selection This connector is used to set the COM2 function. The jumper settings are as follows:
COM 2
Function
Jumper Settings
(pin closed)
Jumper
Illustrations
RS-232 All Open
RS-422 1-2, 3-4, 9-10
RS-485 1-2, 5-6, 7-8
*** Manufacturing default -- RS-232.
Chapter 2 Hardware Configuration
PMB-881LF USER′S MANUAL
Page: 2-11
2-8. COM2 AUTO DETECT SELECTION
JP10: COM2 Auto Detect selection The selections are as follows:
SELECTION
JUMPER
SETTINGS
JUMPER
ILLUSTRATION
NORMAL 1-2
JP10
AUTO GATING
2-3
JP10
***Manufacturing Default – Normal.
Chapter 2 Hardware Configuration
Page: 2-12
PMB-881LF USER′S MANUAL
2-9. KEYBOARD AND PS/2 MOUSE CONNECTOR
KB_MS1: Keyboard and PS/2 Mouse Connector The pin assignments are as follows:
PIN ASSIGNMENT
1 KBDATA 2 NC 3 GND 4 VCC5 5 KBCLK 6 NC 7 MSDATA 8 NC
9 GND 10 VCC5 11 MSCLK 12 NC
2-10. RESET CONNECTOR
FP1 (5, 7): Reset Connector. The pin assignment is as follows:
PIN ASSIGNMENT
5 GND 7 RST_BTN
Chapter 2 Hardware Configuration
PMB-881LF USER′S MANUAL
Page: 2-13
2-11. HARD DISK DRIVE LED CONNECTOR
FP1 (1, 3): Hard Disk Drive LED Connector The pin assignment is as follows:
PIN ASSIGNMENT
1 HD_LED+ 3 HD_LED-
2-12. ATX POWER BUTTON
FP1 (9, 11): ATX Power Button The pin assignment is as follows:
PIN ASSIGNMENT
9 PWRBTNSW
11 GND
2-13. EXTERNAL SPEAKER CONNECTOR
FP1 (6, 8, 10, 12): External Speaker Connector The pin assignment is as follows:
PIN ASSIGNMENT
6 SPK_VCC
8 SPEAKER SIGNAL 10 SPEAKER SIGNAL 12 SPEAKER SIGNAL
Chapter 2 Hardware Configuration
Page: 2-14
PMB-881LF USER′S MANUAL
2-14. PLED CONNECTOR
FP1 (2, 4) : PLED Connector The pin assignment is as follows:
PIN ASSIGNMENT
2 PW_LED+
4 PW_LED-
2-15. CLEAR CMOS DATA SELECTION
JP6: Clear CMOS Data Selection The selections are as follows:
FUNCTION
JUMPER
SETTING
(pin closed)
JUMPER
ILLUSTRATION
Normal Open
1
Clear CMOS Close
1
*** Manufacturing Default -- Normal.
Note: To clear CMOS data, user must power-off the computer and set the jumper
to “Clear CMOS” as illustrated above. After five to six seconds, set the jumper back to “Normal” and power-on the computer.
Chapter 2 Hardware Configuration
PMB-881LF USER′S MANUAL
Page: 2-15
2-16. CPU FAN CONNECTOR
CPU_FAN1: CPU Fan connector The pin assignment is as follows:
PIN ASSIGNMENT
1 GND
2 VCC12
3 FAN_TAC1
4 FAN_CTL1
2-17. SYSTEM FAN CONNECTOR
SYS_FAN1: System Fan connector The pin assignment is as follows:
PIN ASSIGNMENT
1 GND
2 VCC12
3 LPC1_FANIO2
CPU_FAN1
Chapter 2 Hardware Configuration
Page: 2-16
PMB-881LF USER′S MANUAL
2-18. TPM CONNECTOR
JLPC1: TPM connector The pin assignment is as follows:
PIN
ASSIGNMENT PIN
ASSIGNMENT
1 CLK 2 GND 3 FRAME 4 NC 5 RESET 6 VCC5 7 LAD3 8 LAD2
9 VCC3 10 LAD1 11 LAD0 12 GND 13 SMBCLK 14 SMBDATA 15 3VSB 16 SERIRQ 17 GND 18 CLK RUN 19 SUS_TAT 20 DREQ0
Chapter 2 Hardware Configuration
PMB-881LF USER′S MANUAL
Page: 2-17
2-19. VGA CONNECTOR
VGA1: VGA Connector
1
5
6
10
11
15
VGA1
PIN ASSIGNMENT
1 CRTRED 2 CRTGREEN 3 CRTBLUE 4 NC 5 GND 6 CRT_ALWAYS_ON 7 GND 8 GND
9 CRTVCC_L 10 GND 11 NC 12 CRTDATA 13 HSYNC 14 VSYNC 15 CRTCLK
Chapter 2 Hardware Configuration
Page: 2-18
PMB-881LF USER′S MANUAL
2-20. SERIAL ATA CONNECTOR
SATA1~SATA6: The PMB-881LF possesses Six Serial ATA Connector, SATA1~SATA6. The pin assignments are as follows:
SATA1:
PIN ASSIGNMENT
1 GND 2 SATA_TXPC0 3 SATA_TXNC0 4 GND 5 SATA_RXNC0 6 SATA_RXPC0 7 GND
SATA2:
PIN ASSIGNMENT
1 GND 2 SATA_TXPC1 3 SATA_TXNC1 4 GND 5 SATA_RXNC1 6 SATA_RXPC1 7 GND
SATA3:
PIN ASSIGNMENT
1 GND 2 SATA_TXPC2 3 SATA_TXNC2 4 GND 5 SATA_RXNC2 6 SATA_RXPC2 7 GND
Chapter 2 Hardware Configuration
PMB-881LF USER′S MANUAL
Page: 2-19
SATA4:
PIN ASSIGNMENT
1 GND 2 SATA_TXPC3 3 SATA_TXNC3 4 GND 5 SATA_RXNC3 6 SATA_RXPC3 7 GND
SATA5:
PIN ASSIGNMENT
1 GND 2 SATA_TXPC4 3 SATA_TXNC4 4 GND 5 SATA_RXNC4 6 SATA_RXPC4 7 GND
SATA6:
PIN ASSIGNMENT
1 GND 2 SATA_TXPC5 3 SATA_TXNC5 4 GND 5 SATA_RXNC5 6 SATA_RXPC5 7 GND
Chapter 2 Hardware Configuration
Page: 2-20
PMB-881LF USER′S MANUAL
2-21. PRINTER CONNECTOR
LPT1: Printer Connector As to link the Printer to the card, you need a cable to connect both DB25 connector and parallel port. The pin assignments are as follow:
PIN ASSIGNMENT PIN ASSIGNMENT
1 STB 14 AFD# 2 PDR0 15 ERR# 3 PDR1 16 INIT# 4 PDR2 17 SLIN# 5 PDR3 18 GND 6 PDR4 19 GND 7 PDR5 20 GND 8 PDR6 21 GND
9 PDR7 22 GND 10 ACK# 23 GND 11 BUSY 24 GND 12 PE 25 GND 13 SLCT 26 NC
Chapter 2 Hardware Configuration
PMB-881LF USER′S MANUAL
Page: 2-21
2-22. UNIVERSAL SERIAL BUS CONNECTOR
USB1: Universal Serial Bus Connector The pin assignments are as follows:
PIN ASSIGNMENT
1 USB_67_VCC5 2 USB_67_VCC5 3 USBN6 4 USBN7 5 USBP6 6 USBP7 7 GND 8 GND 9 NC
10 GND
USB2: Universal Serial Bus Connector The pin assignments are as follows:
PIN ASSIGNMENT
1 USB_89_VCC5 2 USB_89_VCC5 3 USBN8 4 USBN9 5 USBP8 6 USBP9 7 GND 8 GND 9 NC
10 GND
Chapter 2 Hardware Configuration
Page: 2-22
PMB-881LF USER′S MANUAL
USB3: Universal Serial Bus Connector The pin assignments are as follows:
PIN ASSIGNMENT
1 USB_1011_VCC5 2 USB_1011_VCC5 3 USBN10 4 USBN10 5 USBP11 6 USBP11 7 GND 8 GND 9 NC
10 GND
USBDOM1: Universal Serial Bus Connector The pin assignments are as follows:
PIN ASSIGNMENT
1 USB_45_VCC5 2 USB_45_VCC5 3 USBN4 4 USBN5 5 USBP4 6 USBP5 7 GND 8 GND 9 NC
10 GND
Chapter 2 Hardware Configuration
PMB-881LF USER′S MANUAL
Page: 2-23
2-23. IRDA CONNECTOR
IR1: IrDA (Infrared) Connector The pin assignments are as follows:
PIN ASSIGNMENT
1 VCC5 2 NC 3 IRRX 4 GND 5 IRTX
Chapter 2 Hardware Configuration
Page: 2-24
PMB-881LF USER′S MANUAL
2-24. USB & LAN CONNECTOR
LAN1_USB1: USB & LAN Connector The pin assignments are as follows:
LAN Signal:
PIN ASSIGNMENT
1 VCC_LAN1 2 LAN1_MDI_0P 3 LAN1_MDI_0N 4 LAN1_MDI_1P 5 LAN1_MDI_1N 6 LAN1_MDI_2P 7 LAN1_MDI_2N 8 LAN1_MDI_3P 9 LAN1_MDI_3N
10 COM_LAN1
LAN LED Indicator: Left Side LED
RED Color On Giga LAN Speed Indicator
Off No LAN switch/ hub connected.
Right Side LED
Orange Color Blinking LAN Message Active
Off No LAN Message Active
USB Signal:
PIN ASSIGNMENT
A1 VCCUSB1 A2 USBP0N A3 USBP0P A4 GND B1 VCCUSB0 B2 USBP1N B3 USBP1P B4 GND
Chapter 2 Hardware Configuration
PMB-881LF USER′S MANUAL
Page: 2-25
LAN2_USB2: USB & LAN Connector
The pin assignments are as follows
LAN Signal:
PIN ASSIGNMENT
1 VCC_LAN2 2 LAN2_MDI_0P 3 LAN2_MDI_0N 4 LAN2_MDI_1P 5 LAN2_MDI_1N 6 LAN2_MDI_2P 7 LAN2_MDI_2N 8 LAN2_MDI_3P 9 LAN2_MDI_3N
10 COM_LAN2
LAN LED Indicator: Left Side LED
RED Color On Giga LAN Speed Indicator
Off No LAN switch/ hub connected.
Right Side LED
Orange Color Blinking LAN Message Active
Off No LAN Message Active
USB Signal:
PIN ASSIGNMENT
A1 VCCUSB3 A2 USBP2N A3 USBP2P A4 GND B1 VCCUSB2 B2 USBP3N B3 USBP3P B4 GND
Chapter 2 Hardware Configuration
Page: 2-26
PMB-881LF USER′S MANUAL
2-25. DISPLAY PORT CONNECTOR
JDP1: Display Port Connector The pin assignments are as follows:
PIN ASSIGNMENT PIN ASSIGNMENT
1 DP_C_DATA0+ 2 GND
3 DP_C_DATA0- 4 DP_C_DATA1+
5 GND 6 DP_C_DATA1-
7 DP_C_DATA2+ 8 GND
9 DP_C_DATA2- 10 DP_C_DATA3+
11 GND 12 DP_C_DATA3­13 DP_C_AUX_ENJ 14 GND 15 DP_C_AUX+ 16 DP_C_HPD 17 DP_C_AUX- 18 DP_VCC3_3 19 DP_VCC5 20 DP_VCC3_3
JDP2: Display Port Connector The pin assignments are as follows:
PIN ASSIGNMENT PIN ASSIGNMENT
1 DP_D_DATA0+ 2 GND
3 DP_D_DATA0- 4 DP_D_DATA1+
5 GND 6 DP_D_DATA1-
7 DP_D_DATA2+ 8 GND
9 DP_D_DATA2- 10 DP_D_DATA3+
11 GND 12 DP_D_DATA3­13 DP_D_AUX_ENJ 14 GND 15 DP_D_AUX+ 16 DP_D_HPD 17 DP_D_AUX- 18 DP_VCC3_3 19 DP_VCC5 20 DP_VCC3_3
Chapter 2 Hardware Configuration
PMB-881LF USER′S MANUAL
Page: 2-27
2-26. DIGITAL INPUT/OUTPUT CONNECTOR
DIO1: Digital I/O Connector The pin assignments are as follows:
PIN ASSIGNMENT PIN ASSIGNMENT
1 VCC5 2 VCC12
3 DIN0 4 DOUT0
5 DIN1 6 DOUT1
7 DIN2 8 DOUT2
9 DIN3 10 DOUT3
11 DIN4 12 DOUT4 13 DIN5 14 DOUT5 15 DIN6 16 DOUT6 17 DIN7 18 DOUT7 19 GND 20 GND
DIO1
1 2
19 20
Chapter 2 Hardware Configuration
Page: 2-28
PMB-881LF USER′S MANUAL
2-27. ATX POWER CONNECTOR
ATX_PWR1: ATX Power Connector The pin assignments are as follows:
PIN ASSIGNMENT PIN ASSIGNMENT
1 +3.3V 13 +3.3V
2 +3.3V 14 -12V
3 GND 15 GND
4 +5V 16 PSON
5 GND 17 GND
6 +5V 18 GND
7 GND 19 GND
8 POK 20 -5V
9 5VSB 21 +5V 10 +12V 22 +5V 11 +12V 23 +5V 12 +3.3V 24 GND
Chapter 2 Hardware Configuration
PMB-881LF USER′S MANUAL
Page: 2-29
2-28. SOUND CONNECTOR
AUDIO1: Sound Connector, including Line-In, Line-Out & Mic. Also can support only MIC connector. The pin assignments are as follows:
Line-In
PIN ASSIGNMENT
32 HD_LINE-L 33 GND 34 GND 35 HD_LINE-R
Line-Out
PIN ASSIGNMENT
22 HD_OUT-L 23 NC 24 NC 25 HD_OUT-R
Mic-In
PIN ASSIGNMENT
1 GND 2 HD_MIC1 3 HD_MIC_GND 4 NC 5 HD_MIC_VCC
SPDIF (Optional, the same port with Line-In)
PIN ASSIGNMENT
42 GND 43 VCC_AUD 44 SPDIF OUT
AUDIO1
1 2345
22232425
32333435
Page: 3-1
SOFTWARE UTILITIES
This chapter comprises the detailed information of VGA driver, LAN driver, and Sound driver.
Section includes:
Intel® Chipset Software Installation Utility
VGA Driver Utility
LAN Driver Utility
SOUND Driver Utility
ME Driver Utility
CHAPTER
3
Chapter 3 Software Configuration
Page:3-2
PMB-881LF USER′S MANUAL
3-1. INTRODUCTION
Enclosed with our PMB-881LF package, you will find a CD ROM disk containing all types of drivers we have. As a PMB-881LF user, you will only need the some of files contained in the CD ROM disk, please take note of the following chart:
File name
(Assume that CD ROM drive is D:)
Purpose
D:\Driver\FLASH For BIOS update utility D:\Driver\UTILITY Intel® Chipset Device Software
Installation Utility
D:\Driver\VGA Intel® HD Graphics Family f
or VGA
driver installation
D:\Driver\LAN Intel® 82579LM and 82583V for
LAN Driver installation
D:\Driver\SOUND Realtek® ALC888S f
or Sound driver
installation
D:\Driver\ME For Intel Management Engine
Interface D:\Driver\Intel® Rapid Storage Intel Matrix Storage Manager Utility D:\Driver\F6Floppy Intel F6 Floppy Utility
User should remember to install the Utility right after the OS fully installed.
Chapter 3 Software Configuration
PMB-881LF USER′S MANUAL
Page:3-3
3-2. INTEL® CHIPSET SOFTWARE INSTALLATION UTILITY
3-2-1. Introduction
The Intel® Chipset Device Software installs Windows* INF files to the target system. These files outline to the operating system how to configure the Intel® chipset components in order to ensure that the following features function properly:
- Core PCI and ISAPNP Services
- PCIe Support
- IDE/ATA33/ATA66/ATA100 Storage Support
- SATA Storage Support
- USB Support
- Identification of Intel(R) Chipset Components in the Device
Manager
3-2-2. Installation of Utility for Windows XP/Vista/7/Server 2003/2008
The Utility Pack is to be installed only for Windows XP, Windows Vista, Windows 7, and Windows Server 2003 and 2008 program. It should be installed right after the OS installation, kindly follow the following steps:
1. Place insert the Utility Disk into Floppy Disk Drive A/B or CD
ROM drive.
2. Under Windows system, go to the directory where Utility Disc is
located. e.g. :\DRIVER\UTILITY\infinst_autol.exe
3. Click infinst_autol.exe file for utility installation.
4. Follow the instructions on the screen to complete the installation.
5. Once installation is completed, shut down the system and restart in
order for the changes to take effect.
Chapter 3 Software Configuration
Page:3-4
PMB-881LF USER′S MANUAL
3-3. VGA DRIVER UTILITY
The VGA interface is embedded with our PMB-881LF system to support CRT display. The following illustration briefly shows you the content of VGA driver in D:\Driver\VGA.
3-3-1. Installation of VGA Driver
1. Start the computer (Win XP/Vista/7).
2. Insert the Utility Disk into the CD ROM drive or drive A/B.
3. Open the VGA folder, for your system to choose an appropriate folder, and
double-click "exe" file to install. e.g. d:\DRIVER\VGA\Your system\ ***.exe (If D is not your CD-ROM drive, substitute D with the correct drive letter.)
4. Follow the Wizard's on-screen instructions to complete the installation.
Chapter 3 Software Configuration
PMB-881LF USER′S MANUAL
Page:3-5
3-4. LAN DRIVER UTILITY
3-4-1. Introduction
The PMB-881LF is enhanced with LAN function that can support various network adapters. The content of the LAN driver is found as follows:
1. Win XP program
2. Win Vista program
3. Win 7 program
4. Win Server 2003 program
5. Win Server 2008 program*
Note: Intel 82583V GbE LAN not support
Windows Server 2008.
For more details on Installation procedure, please refer to Readme.txt file found on LAN DRIVER UTILITY.
Chapter 3 Software Configuration
Page:3-6
PMB-881LF USER′S MANUAL
3-5. SOUND DRIVER UTILITY
3-5-1. Introduction
The Audio chip enhanced in this system is fully compatible with Windows XP, Windows Vista and Windows 7. Below, you will find the content of the Sound driver:
3-5-2. Installation Procedure for Windows XP/Vista/7
1. Open the SOUND folder. For your system to choose an appropriate folder,
and Run the setup.exe program to start the installation. e.g. :\DRIVER\SOUND\Your system\setup.exe (If D is not your CD-ROM drive, substitute D with the correct drive letter.)
2. Click on [Next] to continue the procedure. If the Windows popup
"Windows can't verify the publisher of this driver software" message, press "Install this driver software anyway" to continue the installation.
3. Finally, select to restart the system and press [Finish] to complete the
installation.
Chapter 3 Software Configuration
PMB-881LF USER′S MANUAL
Page:3-7
3-6. INTEL ME DRIVER UTILITY
3-6-1. Introduction
The Intel ME components include the Intel Management and Security Status Application. The content of the ME driver is found as follows:
For more details on Installation procedure, please refer to Readme.txt file found on ME DRIVER UTILITY.
Page: 4-1
AMI BIOS SETUP
This chapter shows how to set up the AMI BIOS.
Section includes:
Introduction
Entering Setup
Main
Advanced
Chipset
Boot
Security
Save & Exit
CHAPTER
4
Chapter 4 AMI BIOS Setup
Page: 4-2
PMB-881LF USER′S MANUAL
4-1. INTRODUCTION
The board PMB-881LF uses an AMI Aptio BIOS that is stored in the Serial Peripheral Interface Flash Memory (SPI Flash) and can be updated. The SPI Flash contains the BIOS Setup program, Power-on Self-Test (POST), the PCI auto-configuration utility, LAN EEPROM information, and Plug and Play support.
Aptio is AMI’s BIOS firmware based on the UEFI (Unified Extensible Firmware Interface) Specifications and the Intel Platform Innovation Framework for EFI. The UEFI specification defines an interface between an operating system and platform firmware. The interface consists of data tables that contain platform­related information, boot service calls, and runtime service calls that are available to the operating system and its loader. These provide standard environment for booting an operating system and running pre-boot applications.
Following illustration shows Extensible Firmware Interface’s position in the software stack.
Chapter 4 AMI BIOS Setup
PMB-881LF USER′S MANUAL
Page: 4-3
EFI BIOS provides an user interface allow users the ability to modify hardware configuration, e.g. change system date and time, enable or disable a system component, decide bootable device priorities, setup personal password, etc., which is convenient for modifications and customization of the computer system and allows technicians another method for finding solutions if hardware has any problems.
The BIOS Setup program can be used to view and change the BIOS settings for the computer. The BIOS Setup program is accessed by pressing the <Del> or <F2> key after the POST memory test begins and before the operating system boot begins. The settings are shown below.
Chapter 4 AMI BIOS Setup
Page: 4-4
PMB-881LF USER′S MANUAL
4-2. ENTERING SETUP
When the system is powered on, the BIOS will enter the Power-On Self Test (POST) routines and the following message will appear on the lower screen:
POST screen
As long as this message is present on the screen you may press the <Del> key (the one that shares the decimal point at the bottom of the number keypad) to access the Setup program. In a moment, the main menu of the Aptio Setup Utility will appear on the screen:
Chapter 4 AMI BIOS Setup
PMB-881LF USER′S MANUAL
Page: 4-5
Setup program initial screen
You may move the cursor by up/down keys to highlight the individual menu items. As you highlight each item, a brief description of the highlighted selection will appear at the bottom of the screen.
Chapter 4 AMI BIOS Setup
Page: 4-6
PMB-881LF USER′S MANUAL
4-3. Main
Main Screen
BIOS Setting Options Description/Purpose
BIOS Vendor No changeable options Displays the BIOS vendor. Core Version No changeable options Displays the current BIOS core version. Project Version No changeable options Displays the version of the BIOS
currently installed on the platform.
Build Date No changeable options Displays the date of current BIOS
version.
Total Memory No changeable options Displays the current memory installed
amount and type. System Date month, day, year Specifies the current date. System Time hour, minute, second Specifies the current time.
Chapter 4 AMI BIOS Setup
PMB-881LF USER′S MANUAL
Page: 4-7
4-4. Advanced
Advanced Screen
BIOS Setting Options Description/Purpose
Launch PXE OpROM
-Disabled
-Enabled
Enables or disables the boot option for
legacy network devices.
Launch Storage OpROM
-Disabled
-Enabled
Enables or disables the boot option for
legacy mass storage devices with option
ROM.
Chapter 4 AMI BIOS Setup
Page: 4-8
PMB-881LF USER′S MANUAL
4-4.1. Advanced – PCI Subsystems Settings
BIOS Setting Options Description/Purpose
PCI Bus Driver Version
No changeable options Displays the current PCI bus driver
version.
PCI ROM Priority -Legacy ROM
-EFI Compatible ROM
Specifies which PCI ROM is used if there
are multiple ROM available.
PCI Common Settings
No changeable options
PCI Latency Timer - 32 PCI Bus Clocks
- 64 PCI Bus Clocks
- 96 PCI Bus Clocks
-128 PCI Bus Clocks
-160 PCI Bus Clocks
-192 PCI Bus Clocks
-224 PCI Bus Clocks
-248 PCI Bus Clocks
Sets PCI latency time.
Chapter 4 AMI BIOS Setup
PMB-881LF USER′S MANUAL
Page: 4-9
BIOS Setting Options Description/Purpose
VGA Palette Snoop
-Disabled
-Enabled
Enabling this feature turns on this pallete
"snoop". Some special VGA cards need
to be able to look at the video card's
VGA pallete to determine what colors are
currently in use.
PERR# Generation -Disabled
-Enabled
Enables or disables generation of PERR#
signals (data parity errors) used to signal
the detection of a parity error related to a
data phase.
SERR# Generation -Disabled
-Enabled
Enables or disables generation of SERR#
signals (unrecoverable errors) which are
reported to the system and handled by
system software.
PCI Express Device Settings
No changeable options
Relaxed Ordering -Disabled
-Enabled
Enables or disables relaxed ordering
feature which allows transactions that do
not have any order of completion
requirements to complete more
efficiently.
Extended Tag -Disabled
-Enabled
Enables or disables extended tag support
for maximum value of outstanding
requests possible per components from
32 to 2048.
No Snoop -Disabled
-Enabled
Enables or disables no snoop feature to
allow host bridge does not snoop the
processor chache for non-cachable
transactions. It can leads to improved
performance during accesses to non-
cachable memory.
Maximum Payload -Auto
- 128 Bytes
- 256 Bytes
- 512 Bytes
-1024 Bytes
-2048 Bytes
-4096 Bytes
Maxium payload size supported specifies
the size that the function supports for
TLPs (Transaction Layer Packets).
Chapter 4 AMI BIOS Setup
Page: 4-10
PMB-881LF USER′S MANUAL
BIOS Setting Options Description/Purpose
Maximum Read Request
-Auto
- 128 Bytes
- 256 Bytes
- 512 Bytes
-1024 Bytes
-2048 Bytes
-4096 Bytes
Maxium read request size specifies the
size for the device when acting as the
requestor. The device must not generate
read requests with a size larger this value.
PCI Express Link Settings
No changeable options
ASPM Support -Disabled
-Auto
-Force L0
Specifies mode for Active State Power
Management (ASPM), hardware-based
link power conservation mechanism.
Force L0 standby mode applies to a
single direction on the link.
Extended Synch -Disabled
-Enabled
Enabling extended synch feature forces
the transmission of additional ordered
sets when exiting the L0 state and when
in the recovery state. This mode provides
external devices monitoring the link time
to achieve bit symbol lock before the link
enter L0 state and resumes
communication.
Chapter 4 AMI BIOS Setup
PMB-881LF USER′S MANUAL
Page: 4-11
4-4.2. Advanced - ACPI Settings
BIOS Setting Options Description/Purpose
Enable ACPI Auto Configuration
-Disabled
-Enabled
Enables Advanced Configuration and
Power Interface automatic configuration.
When enabled, option ACPI Sleep State
option is not available.
ACPI Sleep State -Suspend Disabled
-S1 (CPU Stop Clock)
-S3 (Suspend to RAM)
Specifies the ACPI sleep state.
Disabled disables ACPI sleep feature.
S1 mode allows the CPU stop executing
instructions.
S3 allows the platform to enter Sleep
(also known as Standby or Suspend to
RAM) mode.
Chapter 4 AMI BIOS Setup
Page: 4-12
PMB-881LF USER′S MANUAL
4-4.3. Advanced -Trusted Computing
BIOS Setting Options Description/Purpose
TPM Support -Disable
-Enable
Allows to active support for Trusted
Platform Module.
TPM State -Disable
-Enable
Allows to enable TPM.
Pending TPM Operation
-None
-Enable Take Ownership
-Disable Take Ownership
-TPM Clear
Enables to applied several options on
TPM.
TPM Enabled Status
No changeable options Reports if TPM is enabled.
TPM Active Status No changeable options Reports the current TPM active status. TPM Owner Status No changeable options Reports the current TPM ownership
status.
Chapter 4 AMI BIOS Setup
PMB-881LF USER′S MANUAL
Page: 4-13
4-4.4. Advanced – CPU Configuration
BIOS Setting Options Description/Purpose
CPU Speed No changeable options Displays the current processor frequency 64-bit No changeable options Reports if 64-bit is supported by
processor.
Hyper-threading -disabled
-enabled
When disabled, only one thread per
active core will operate.
Active Processor Cores
-All
-1
-2
Indicates the number of cores to enable in
processor.
Limit CPUID Maximum
-disabled
-enabled
Enables for legacy operating systems to
boot processors with extended CPUID
functions.
Hardware Prefetcher
-disabled
-enabled
Hardware prefetcher looks into the
stream of data. Data is prefetched into L2
cache from external memory.
Chapter 4 AMI BIOS Setup
Page: 4-14
PMB-881LF USER′S MANUAL
BIOS Setting Options Description/Purpose
Adjacent Cache Line Prefetch
-disabled
-enabled
Enables Adjanced cache line prefetch
feature in order to effectivelly hide
memory latency and improve application
performance.
Intel Virtualization
Technology
-disabled
-enabled
Enables or disables Intel Virtualization
Technology (VT-x). Takes affect only
after power cycling.
Power Technology -Disabled
-Energy Efficient
-Custom
Enable the power management features.
EIST -disabled
-enabled
Allows processor to dynamically
transition speed and voltage states using
Enhanced Intel SpeedStep Technology.
Turbo Mode -disabled
-enabled
Allows processor to make use of Intel
Turbo Boost technology. When enabled,
it dynamically changes CPU clock speed
depending on demand and current
processor's operating state and limit.
P-STATE Coordination
-HW_ALL
-SW_ALL
-SW_ANY
Specifies which mode of power-
performance states is applied.
In HW_ALL mode, processor is
responsible for coordinating P-State
among logical processors dependencies.
In SW_ALL the OS power manager
takes care of P-State coordination
between logical processors and must
initiate the transition on all of those
processors.
In SW_ANY mode, the OS power
manager may initiate the transition on
any of those logical processor.
CPU C3 Report -Disabled
-ACPI C-2
-ACPI C3
Enable/Disable CPU C3(ACPI C2) report
to OS.
CPU C6 Report -Enabled
-Disabled
Enable/Disable CPU C6 (ACPI C3)
report to OS.
Chapter 4 AMI BIOS Setup
PMB-881LF USER′S MANUAL
Page: 4-15
BIOS Setting Options Description/Purpose
Package C State limit
-C0
-C2
-C6
-C7
-No Limit
Package C State limit
4-4.4.1. Advanced – CPU Configuration – Socket 0 CPU Information
BIOS Setting Options Description/Purpose
CPU Signature No changeable options Reports the CPU Signature Microcode Patch No changeable options Reports the CPU Microcode Patch
Version.
Max CPU Speed No changeable options Reports the Max CPU Speed. Min CPU Speed No changeable options Reports the Min CPU Speed
Chapter 4 AMI BIOS Setup
Page: 4-16
PMB-881LF USER′S MANUAL
BIOS Setting Options Description/Purpose
Processor Cores No changeable options Displays number of physical cores in
processor.
Intel HT Technology
No changeable options Reports if Intel Hyper-Threading
Technology is supported by processor
Intel VT-x Technology
No changeable options Reports if Intel VT-x Technology is
supported by processor.
Intel SMX Technology
No changeable options Reports if Intel SMX Technology is
supported by processor.
L1 Data Cache No changeable options Displays number of L1 Data Cache L1 Code Cache No changeable options Displays number of L1 Code Cache L2 Cache No changeable options Displays number of L2 Cache. L3 Cache No changeable options Displays number of L3 Cache.
Chapter 4 AMI BIOS Setup
PMB-881LF USER′S MANUAL
Page: 4-17
4-4.5. Advanced – SATA Configuration
BIOS Setting Options Description/Purpose
SATA Mode -disable
-IDE Mode
-AHCI Mode
-RAID Mode
Configures SATA as following:
IDE Mode
AHCI Mode allows to take advantage of
Advanced Host Controller Interface
features such as NCQ (Native Command
Queuing), Hot plug, etc., without the
option to use RAID.
RAID Mode enables RAID (Redundant
Array of Inexpensive Disks) which may
require to install the RAID driver during
OS installation.
Chapter 4 AMI BIOS Setup
Page: 4-18
PMB-881LF USER′S MANUAL
BIOS Setting Options Description/Purpose
Serial-ATA Controller 0
-disable
-Enhanced
-Compatible
Specifies the integrated IDE controller 0.
Disabled disables the integrated IDE
controller.
Enhanced enables all SATA and PATA
resources.
Compatible enables up to two IDE
channels for OS requiring legacy IDE
operation.
Serial-ATA Controller 1
-disable
-Enhanced
Specifies the integrated IDE controller 1.
Disabled disables the integrated IDE
controller.
Enhanced enables all SATA and PATA
resources.
SATA Port0 [drive]
Displays the drive installed on this SATA
port. Shows [Not Present] if no drive is
installed.
SATA Port1 [drive]
Displays the drive installed on this SATA
port. Shows [Not Present] if no drive is
installed.
SATA Port2 [drive]
Displays the drive installed on this SATA
port. Shows [Not Present] if no drive is
installed.
SATA Port3 [drive]
Displays the drive installed on this SATA
port. Shows [Not Present] if no drive is
installed.
SATA Port4 [drive] Displays the dri
ve installed on this SATA
port. Shows [Not Present] if no drive is
installed.
SATA Port5 [drive]
Displays the drive installed on this SATA
port. Shows [Not Present] if no drive is
installed.
Chapter 4 AMI BIOS Setup
PMB-881LF USER′S MANUAL
Page: 4-19
4-4.5.1. Advanced – SATA Configuration – AHCI Mode
BIOS Setting Options Description/Purpose
Port 0 Hot Plug -disable
-enable
Enables or disables support hot plug
feature on port 0.
Port 1 Hot Plug -disable
-enable
Enables or disables support hot plug
feature on port 1.
Port 2 Hot Plug -disable
-enable
Enables or disables support hot plug
feature on port 2.
Port 3 Hot Plug -disable
-enable
Enables or disables support hot plug
feature on port 3.
Port 4 Hot Plug -disable
-enable
Enables or disables support hot plug
feature on port 4.
Port 5 Hot Plug -disable
-enable
Enables or disables support hot plug
feature on port 5.
Chapter 4 AMI BIOS Setup
Page: 4-20
PMB-881LF USER′S MANUAL
BIOS Setting Options Description/Purpose
External SATA Port 0
-disable
-enable
Configures SATA port 0 as external
SATA port.
External SATA Port 1
-disable
-enable
Configures SATA port 1 as external
SATA port.
External SATA Port 2
-disable
-enable
Configures SATA port 2 as external
SATA port.
External SATA Port 3
-disable
-enable
Configures SATA port 3 as external
SATA port.
External SATA Port 4
-disable
-enable
Configures SATA port 4 as external
SATA port.
External SATA Port 5
-disable
-enable
Configures SATA port 5 as external
SATA port.
Chapter 4 AMI BIOS Setup
PMB-881LF USER′S MANUAL
Page: 4-21
4-4.5.2. Advanced – SATA Configuration – RAID Mode
BIOS Setting Options Description/Purpose
Port 0 Hot Plug -disable
-enable
Enables or disables support hot plug
feature on port 0.
Port 1 Hot Plug -disable
-enable
Enables or disables support hot plug
feature on port 1.
Port 2 Hot Plug -disable
-enable
Enables or disables support hot plug
feature on port 2.
Port 3 Hot Plug -disable
-enable
Enables or disables support hot plug
feature on port 3.
Port 4 Hot Plug -disable
-enable
Enables or disables support hot plug
feature on port 4.
Port 5 Hot Plug -disable
-enable
Enables or disables support hot plug
feature on port 5.
Chapter 4 AMI BIOS Setup
Page: 4-22
PMB-881LF USER′S MANUAL
4-4.6. Advanced – Intel TXT(LT) Configuration
BIOS Setting Options Description/Purpose
SMX Feature Support
No changeable options
Reports if processor supports Safer Mode
Extensions instructions (SMX).
Intel TXT(LT) Support
-disabled
-enabled
Enables or disables Intel Trusted
Execution Technology. Takes affect only
after power cycling.
Chapter 4 AMI BIOS Setup
PMB-881LF USER′S MANUAL
Page: 4-23
4-4.7. Advanced – Intel IGD SWSCI OpRegion
BIOS Setting Options Description/Purpose
DVMT Mode Select
-Fixed Mode
-DVMT Mode
Select DVMT Mode used by Internal
Graphics Device.
DVMT/FIXED Memory
-128MB
-256MB
-Maximum
Intel Dynamic Video Memory
Technology allows additional memory to
be allocated for graphics usage based on
application need. Once the application is
closed, the memory that was allocated for
graphics usage is then released and made
available for system use.
IGD - Boot Type -VBIOS Default Specifies which graphics output is used
on system boot.
Chapter 4 AMI BIOS Setup
Page: 4-24
PMB-881LF USER′S MANUAL
4-4.8. Advanced – USB Configuration
BIOS Setting Options Description/Purpose
USB Devices No changeable options Displays number of available USB
devices.
Legacy USB Support
-disabled
-enabled
-Auto
Enables support for legacy USB.
EHCI Hand-off -disabled
-enabled
When enabled it allows BIOS support
control of the EHCI controller and the
OS handoff synchronization capatability.
USB transfer time­out
-1 sec
-5 sec
-10 sec
-20 sec
Specifies the value for USB transfer
time-out.
Chapter 4 AMI BIOS Setup
PMB-881LF USER′S MANUAL
Page: 4-25
BIOS Setting Options Description/Purpose
Device Reset timeout
-10 sec
-20 sec
-30 sec
-40 sec
Specifies the value for device reset
timeout.
4-4.9. Advanced – W83627UHG Super IO Configuration
BIOS Setting Options Description/Purpose
Super IO Chip No changeable options Displays the super IO chip model and its
manufacturer.
Chapter 4 AMI BIOS Setup
Page: 4-26
PMB-881LF USER′S MANUAL
4-4.9.1. Advanced – W83627UHG Super IO Configuration –
Watchdog Configuration
BIOS Setting Options Description/Purpose
TimeSelector -Minute
-Second
Selects unit for watchdog timer.
TimeOut multiple options
ranging from 0 to 255
Sets the desired value for watchdog
timer.
Chapter 4 AMI BIOS Setup
PMB-881LF USER′S MANUAL
Page: 4-27
4-4.9.2. Advanced – W83627UHG Super IO Configuration – Floppy
Disk Controller Configuration
BIOS Setting Options Description/Purpose
Floppy Disk Controller
-Enabled
-Disabled
Enable or Disable Floppy Disk Controller.
Change Settings -Auto
-IO=3F0h; IRQ=6; DMA=2;
-IO=3F0h; IRQ=3,4,5,6,7,10,11,12; DMA=2,3;
-IO=370h; IRQ=3,4,5,6,7,10,11,12; DMA=2,3;
Select an iptimal settins for Super IO Device.
Device Mode -Read Write
-Write Protect
Change Mode of Floppy Disk Controller. Select <Read Write> mode for Normal operatuion. Select <Write Protect> mode for readonly operation.
Chapter 4 AMI BIOS Setup
Page: 4-28
PMB-881LF USER′S MANUAL
4-4.9.3. Advanced – W83627UHG Super IO Configuration – Serial
Port 1 Configuration
BIOS Setting Options Description/Purpose
Serial Port -disabled
-enabled
Configures the serial port 1.
Device Settings No changeable options
Reports the current serial
port 1 setting.
Change Settings -Auto
-IO=3F8h; IRQ=4
-IO=3F8h; IRQ=3,4,5,6,7,10,11,12
-IO=2F8h; IRQ=3,4,5,6,7,10,11,12
-IO=3E8h; IRQ=3,4,5,6,7,10,11,12
-IO=2E8h; IRQ=3,4,5,6,7,10,11,12
Specifies the base I/O address and interrupt request for the serial port 1 if enabled.
Chapter 4 AMI BIOS Setup
PMB-881LF USER′S MANUAL
Page: 4-29
4-4.9.4. Advanced – W83627UHG Super IO Configuration – Serial
Port 2 Configuration
BIOS Setting
BIOS SettingBIOS Setting
BIOS Setting Options
OptionsOptions
Options Description/Purpose
Description/PurposeDescription/Purpose
Description/Purpose
Serial Port -disabled
-enabled
Configures the serial port 2.
Device Settings No changeable options Reports the current serial
port 2 setting.
Change Settings -Auto
-IO=3F8h; IRQ=4
-IO=3F8h; IRQ=3,4,5,6,7,10,11,12
-IO=2F8h; IRQ=3,4,5,6,7,10,11,12
-IO=3E8h; IRQ=3,4,5,6,7,10,11,12
-IO=2E8h; IRQ=3,4,5,6,7,10,11,12
Specifies the base I/O address and interrupt request for the serial port 2 if enabled.
Chapter 4 AMI BIOS Setup
Page: 4-30
PMB-881LF USER′S MANUAL
BIOS Setting
BIOS SettingBIOS Setting
BIOS Setting Options
OptionsOptions
Options Description/Purpose
Description/PurposeDescription/Purpose
Description/Purpose
Device Mode -Serial Port Mode
-IrDA Mode
-ASK-IR Mode
Configures the serial port 2 mode. Serial Port Mode default settings for the serial port 2. IrDA (Infrared Data Association) general infrared protocol. ASK-IR (Amplitude Shift
Keyed IR) infrared protocol
developed by Sharp.
Chapter 4 AMI BIOS Setup
PMB-881LF USER′S MANUAL
Page: 4-31
4-4.9.5. Advanced – W83627UHG Super IO Configuration – Serial
Port 3 Configuration
BIOS Setting Options Description/Purpose
Serial Port -disabled
-enabled
Configures the serial port 3.
Device Settings No changeable options Reports the current serial
port 3 setting.
Change Settings -Auto
-IO=3F8h; IRQ=4
-IO=3F8h; IRQ=3,4,5,6,7,10,11,12
-IO=2F8h; IRQ=3,4,5,6,7,10,11,12
-IO=3E8h; IRQ=3,4,5,6,7,10,11,12
-IO=2E8h; IRQ=3,4,5,6,7,10,11,12
Specifies the base I/O address and interrupt request for the serial port 3 if enabled.
Chapter 4 AMI BIOS Setup
Page: 4-32
PMB-881LF USER′S MANUAL
4-4.9.6. Advanced – W83627UHG Super IO Configuration – Serial
Port 4 Configuration
BIOS Setting Options Description/Purpose
Serial Port -disabled
-enabled
Configures the serial port 4.
Device Settings No changeable options Reports the current serial
port 4 setting.
Change Settings -Auto
-IO=3F8h; IRQ=4
-IO=3F8h; IRQ=3,4,5,6,7,10,11,12
-IO=2F8h; IRQ=3,4,5,6,7,10,11,12
-IO=3E8h; IRQ=3,4,5,6,7,10,11,12
-IO=2E8h; IRQ=3,4,5,6,7,10,11,12
Specifies the base I/O address and interrupt request for the serial port 4 if enabled.
Chapter 4 AMI BIOS Setup
PMB-881LF USER′S MANUAL
Page: 4-33
4-4.9.7. Advanced – W83627UHG Super IO Configuration – Parallel
Port Configuration
BIOS Setting Options Description/Purpose
Parallel Port -disabled
-enabled
Configures the parallel port.
Device Settings No changeable options
Reports the current parallel
port setting.
Change Settings -Auto
-IO=378h; IRQ=5
-IO=378h; IRQ=5,6,7,10,11,12
-IO=278h; IRQ=5,6,7,10,11,12
-IO=3BCh; IRQ=5,6,7,10,11,12
-IO=378h;
-IO=278h;
-IO=3BCh;
Specifies the base I/O address and interrupt
request for the parallel port
if enabled.
Chapter 4 AMI BIOS Setup
Page: 4-34
PMB-881LF USER′S MANUAL
BIOS Setting Options Description/Purpose
Device Mode -STD Printer Mode
-SPP Mode
-EPP-1.9 and SPP Mode
-EPP-1.7 and SPP Mode
-ECP Mode
-ECP and EPP 1.9 Mode
-ECP and EPP 1.7 Mode
Selects the mode for the parallel port. Not available if the parallel port is disabled. SPP is Standard Parallel Port mode, a bi-directional mode for printers. EPP is Enhanced Parallel Port mode, a high-speed bi-directional mode for non-printer peripherals. ECP is Enhanced Capability Port mode, a high-speed bi-directional mode for printers and scanners.
Chapter 4 AMI BIOS Setup
PMB-881LF USER′S MANUAL
Page: 4-35
4-4.10. Advanced –H/W Monitor
BIOS Setting Options Description/Purpose
System Temperature
No changeable options Displays temperature in the remote
thermal sensor zone.
CPU Temperature No changeable options Displays processor's temperature. System Fan Speed No changeable options Displays fan speed of the chassis fan. CPU Fan Speed No changeable options Displays fan speed of the CPU fan. VCORE No changeable options
Displays voltage level of the +VCORE in
supply.
12V No changeable options Displays voltage level of the +12V in
supply.
1.5V No changeable options Displays voltage level of the +1.5V in supply.
5VCC No changeable options Displays voltage level of the +5V in
supply.
Chapter 4 AMI BIOS Setup
Page: 4-36
PMB-881LF USER′S MANUAL
BIOS Setting Options Description/Purpose
1.05V No changeable options Displays voltage level of the +1.5V in supply.
5VSB No changeable options Displays voltage level of the +5VSB in
supply.
VBAT No changeable options Displays voltage level of the backup
CMOS battery.
4-4.11. Advanced – AMT Configuration
BIOS Setting Options Description/Purpose
AMT -disabled
-enabled
Enables Intel Active Management Technology (Intel AMT) functionality.
Unconfigure AMT/ME
-disabled
-enabled
Allows to unconfigure Intel ME after BIOS POST process is completed.
Chapter 4 AMI BIOS Setup
PMB-881LF USER′S MANUAL
Page: 4-37
4-4.12. Advanced – Serial Port Console Redirection
BIOS Setting Options Description/Purpose
Console Redirection
-disabled
-enabled
Enables or disables console redirection feature.
Chapter 4 AMI BIOS Setup
Page: 4-38
PMB-881LF USER′S MANUAL
BIOS Setting Options Description/Purpose
Out-
of Band Mgmt
Port
-COM0
-COM4(PCI Dev0,Func0)
Microsoft Windows Emergency Management Sevices allows for remote management of a Windows Server OS. through a serial port.
Terminal Type -[VT100]
-[VT100+]
-[VT-UTF8]
-ANSI
Specifies which remote terminal emulation standard is in use.
Bits per second -9600
-19200
-57600
-115200
Selects serial port transmission speed. The speed must be matched on the other side. Long or noisy lines may require lower speeds.
Chapter 4 AMI BIOS Setup
PMB-881LF USER′S MANUAL
Page: 4-39
BIOS Setting Options Description/Purpose
Flow Control -None
-Hardware RTS/CTS
-Software Xon/Xoff
Flow control can prevent data loss from buffer overflow. When speding data, if the recieving buffers are full, a ’stop’ signal can be sent to stop the data flow. Once the buffers are empty, a ’start’signal can be sent to re-start the flow. Hareware flow control uses two wires to send start/stop signals.
Chapter 4 AMI BIOS Setup
Page: 4-40
PMB-881LF USER′S MANUAL
4-5. Chipset
Chapter 4 AMI BIOS Setup
PMB-881LF USER′S MANUAL
Page: 4-41
4-5.1. Chipset – North Bridge
BIOS Setting Options Description/Purpose
Total Memory No changeable options Displays the total amount of RAM. Memory Slot0 No changeable options Display the amount of RAM installed in
first memory slot.
Memory Slot1 No changeable options not available Memory Slot2 No changeable options Display the amount of RAM installed in
second memory slot.
Memory Slot3 No changeable options not available Low MMIO Align -64M
-1024M
Selects the different remapping size.
VT-d -disabled
-enabled
Enables or disables Intel VT for directed I/O (Intel VT-d).
Chapter 4 AMI BIOS Setup
Page: 4-42
PMB-881LF USER′S MANUAL
BIOS Setting Options Description/Purpose
Initiate Graphic Adapter
-IGD
-PCI/IGD
-PCI/PEG
-PEG/IGD
-PEG/PCI
Allows selecting a specific video controller or their combination as the display device that will be active when the system boots.
IGD Memory -disable
-32M
-64M
-96M
-128M ….
-512M
Establishes the maximum amount of system memory that the operating system can use for video memory.
PCI Express Prot -disabled
-enabled
-Auto
Enable/Disable/Auto PCI-E port.
PEG Force Gen1 -disabled
-enabled
If enabled, it will force the maximum speed of PCI Express card to Generation 1 mode, even if the card supports Generation 2.
Chapter 4 AMI BIOS Setup
PMB-881LF USER′S MANUAL
Page: 4-43
4-5.2. Chipset – South Bridge
BIOS Setting Options Description/Purpose
SMBus Controller -disabled
-enabled
Enables or disables the system bus controller. It monitors system's temperature and voltage.
Restore AC Power Loss
-Power Off
-Power On
-Last State
Determines the mode of operation in case
of power loss. Power Off keeps the power off till the power button is pressed. Power On restores power to the computer. Last State restores the previous power state before power loss happened.
SLP_S4 Assertion Stretch Enable
-disabled
-enabled
When enabled it sets the value specified by SLP_S4 Assertion Width option.
Chapter 4 AMI BIOS Setup
Page: 4-44
PMB-881LF USER′S MANUAL
BIOS Setting Options Description/Purpose
SLP_S4 Assertion Width
-1-2 Seconds
-2-3 Seconds
-3-4 Seconds
-4-5 Seconds
Sets the minimum assertion width of the SLP_S4# signal (power plane control) to guarantee the DRAM has been safely power-cycled.
Azalia HD Audio -Disabled
-Enabled
Enabled/Disabled Azalia HD Audio
Azalia internal HDMI codec
-Disabled
-Enabled
Enabled/Disabled Internal HDMI codec for Azalia.
High Precision Event Timer Configuration
-disabled
-enabled
Enables or disables High Precision Even Timer support.
Chapter 4 AMI BIOS Setup
PMB-881LF USER′S MANUAL
Page: 4-45
4-5.2.1. Chipset – South Bridge – USB Configuration
BIOS Setting Options Description/Purpose
All USB Devices -disabled
-enabled
Enables or disables all USB devices.
EHCI Controller 1 -disabled
-enabled
Enables Enhanced Host Controller Interface 1 for high-speed USB functions (USB 2.0).
EHCI Controller 2 -disabled
-enabled
Enables Enhanced Host Controller Interface 2 for high-speed USB functions (USB 2.0).
USB Port 0 -disabled
-enabled
Enables or disables USB Port 0 functionality.
USB Port 1 -disabled
-enabled
Enables or disables USB Port 1 functionality.
USB Port 2 -disabled
-enabled
Enables or disables USB Port 2.
Chapter 4 AMI BIOS Setup
Page: 4-46
PMB-881LF USER′S MANUAL
BIOS Setting Options Description/Purpose
USB Port 3 -disabled
-enabled
Enables or disables USB Port 3 functionality.
USB Port 4 -disabled
-enabled
Enables or disables USB Port 4 functionality.
USB Port 5 -disabled
-enabled
Enables or disables USB Port 5 functionality.
USB Port 8 -disabled
-enabled
Enables or disables USB Port 8 functionality.
USB Port 9 -disabled
-enabled
Enables or disables USB Port 9 functionality.
USB Port 10 -disabled
-enabled
Enables or disables USB Port 10 functionality.
USB Port 11 -disabled
-enabled
Enables or disables USB Port 11 functionality.
USB Port 12 -disabled
-enabled
Enables or disables USB Port 12 functionality.
USB Port 13 -disabled
-enabled
Enables or disables USB Port 13 functionality.
Chapter 4 AMI BIOS Setup
PMB-881LF USER′S MANUAL
Page: 4-47
4-5.2.2. Chipset – South Bridge – USB Configuration (RMH Support
Disabled)
BIOS Setting Options Description/Purpose
PCI Express Port 1~8
-Disabled
-Enabled
-Auto
Disabled/Enabled/Auto the PCI Express Ports in the chipset
PCI-e Sub Decode -Disabled
-Enabled
Enabled/Disable PCI-E Sub Decode port.(This option is availablewhen Subtractive Decode Agent Enable.
Chapter 4 AMI BIOS Setup
Page: 4-48
PMB-881LF USER′S MANUAL
4-5.3. Chipset – ME Subsystem
BIOS Setting Options Description/Purpose
ME Version No changeable options Displays the current Intel Management
Engine version.
ME Subsystem -disabled
-enabled
Enables Intel Management Engine (Intel
ME) functionality. Takes affect only after
power cycling.
End of Post Message
-disabled
-enabled
Enables end of post messages for Intel ME.
Execute MEBx -disabled
-enabled
Enables Intel Management Engine BIOS extension (MEBx).
Chapter 4 AMI BIOS Setup
PMB-881LF USER′S MANUAL
Page: 4-49
4-6. Boot
BIOS Setting Options Description/Purpose
Bootup NumLock Status
-On
-Off
Specifies the power-on state of the numlock feature on the numeric keypad of keyboard.
Quiet Boot -disabled
-enabled
When quiet boot is enabled, it displays OEM logo instead of POST messages during boot.
CSM16 Module Version
No changeable options Displays the current Compatibility
Support Module version.
GateA20 Active -Upon Request
-Always
Specifies Gate-A20 logic gate status. At boot time, Gate-A20 is enabled when counting and testing of all the system's memory and disabled before transferring control to OS.
Chapter 4 AMI BIOS Setup
Page: 4-50
PMB-881LF USER′S MANUAL
BIOS Setting Options Description/Purpose
Option ROM Messages
-Force BIOS
-Keep Current
Allows the POST screen to display Option ROM messages.
Interrupt 19 Capture
-disabled
-enabled
When enabled it allows host adapters ROM BIOS to capture Interrupt 19 during the boot process and eventually boot from disk(s) connected to those adapters.
Boot Option #1~#3
-[drive(s)]
-disabled
Allows to set boot option listed in Hard Drive BBS Priorities.
4-6.1. Boot – Hard Drive BBS Priorities
BIOS Setting
BIOS SettingBIOS Setting
BIOS Setting Options
OptionsOptions
Options Description/Purpose
Description/PurposeDescription/Purpose
Description/Purpose
Boot Option #1 -[drive(s)]
-disabled
Allows setting
the boot order of available
drive(s).
Chapter 4 AMI BIOS Setup
PMB-881LF USER′S MANUAL
Page: 4-51
4-7. Security
BIOS Setting Options Description/Purpose
Administrator Password
Password can be up to 20 alphanumeric characters.
Specifies the administrator password.
User Password Password can be up to
20 alphanumeric characters.
Specifies the user password.
Chapter 4 AMI BIOS Setup
Page: 4-52
PMB-881LF USER′S MANUAL
4-7.1. Security – HDD 0: [drive]
BIOS Setting Options Description/Purpose
Security Supported No changeable options Reports if there is security feature
available.
Security Enabled No changeable options Reports if there is security feature
enabled.
Security Locked No changeable options Reports if there is security feature locked. Security Frozen No changeable options Reports if there is security feature frozen. HDD User Password Status
No changeable options Reports if there is HDD User Passoword
installed.
HDD Master Password Status
No changeable options Reports if there is HDD Master
Passoword installed.
Set User Password Password can be up to
32 alphanumeric characters.
Specifies the user password.
Chapter 4 AMI BIOS Setup
PMB-881LF USER′S MANUAL
Page: 4-53
BIOS Setting Options Description/Purpose
Set Master Password
Password can be up to 32 alphanumeric characters.
Specifies the master password.
Loading...