protech SP-7165, SP-7167 M1 User Manual
USER
SP-7165/7167
15” / 17” Fanless Panel PC
CPU Processor
SP-7165/7167 M1
MANUAL
Powered by Intel® Core
i7/i5/i3 / Pentium® / Celeron®
TM
SP-7165 / SP-7167
15”/17” High Performance Panel PC
COPYRIGHT NOTICE & TRADEMARK
All trademarks and registered trademarks mentioned herein are the
property of their respective owners.
This manual is copyrighted in Jan. 2018. You may not reproduce or
transmit in any form or by any means, electronic, or mechanical,
including photocopying and recording.
DISCLAIMER
This user’s manual is meant to assist users in installing and setting up
the system. The information contained in this document is subject to
change without any notice.
CE NOTICE
This is a class A product. In a domestic environment this product may
cause radio interferen ce in which cas e the us er may be requi red t o take
adequate measures.
FCC NOTICE
Some internal parts of the system may
engineers can open and
disassemble the system. RESTRICTED ACCESS
PERSONS or by USERS who have been instructed
about the reasons for the restrictions applied to the
This equipment has been tested and found to comply with the limits for
a Class A digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and u sed in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
You are cautioned that any change or modifications to the equipment
not expressly approved by the party responsible for compliance could
void your authority to operate such equipment.
CAUTION: Danger of explosion may occur when the
battery is incorrectly replaced. Replace the battery only
with the same or equivalent type recommended by the
manufacturer. Dispose of used batteries according to
the manufacturer’s instructions.
WARNING:
have high electrical voltage. And theref ore we strongl y
recommend that qualified
LOCATION: access can only be gained b y SERVICE
location and about any precautions that shall be taken;
and access is through t he use of a TOOL or lock and
key, or other means of security, and is controlled by
the authority responsible for the location.
Contents
Revision History ........................................................................................... vii
Introduction ......................................................................................... 1-1
1
1.1 About This Manual ..................................................................... 1-2
2 Getting Started .................................................................................... 2-1
2.1 Package List ............................................................................... 2-2
2.2 System Overview ....................................................................... 2-3
2.3 System Specifications ................................................................ 2-9
2.4 Saf et y Precau tio ns ................................................................... 2-11
3 System Configuration ......................................................................... 3-1
3.1 External I/O Ports Diagram ...................................................... 3-14
3.2 SP-7165/SP-7167 Bottom I/O Ports Diagram .......................... 3-14
3.3 Jumper & Connector Quick Reference Table ........................... 3-15
3.4 Component Locations Of System Main Board ......................... 3-17
3.4.1 Top View and Jumper Settings of SB-8400 ...................... 3-17
3.4.2 Bottom View of SB-8400 ................................................... 3-19
3.5 How To Set Jumpers ................................................................ 3-20
3.6 Function Buttons and I/O Ports ................................................ 3-22
3.6.1 Power Button .................................................................... 3-22
3.6.2 DC IN Port (For SP-7165/SP-7167Rx-x0x) ...................... 3-22
3.6.3 DC IN 3 Pins Terminal Block (For SP-7165/SP-7167Rx-x1x) .
......................................................................................... 3-23
3.7 Setting Connectors and Jumpers ............................................. 3-24
3.7.1 COM Port .......................................................................... 3-24
3.7.2 COM1 Pin9 and COM2 PIN18 Definition Selection Guide3-26
3.7.3 LAN1, LAN2 Ports............................................................. 3-27
i
4 x 1 USB 3.0 Connectors ................................................ 3-29
3.7.4
3.7.5 Digital Input/Output Connector (For SP-7165 /
SP-7167Rx-x1x) (optional) ............................................... 3-30
3.7.6 Digital Input/Output Connector (For SP-7165 /
SP-7167Rx-x0x) (optional) ............................................... 3-31
3.7.7 DVI-I Port .......................................................................... 3-32
3.7.8 HD Audio Connector ......................................................... 3-33
3.7.10 Mini PCI Express Slots ..................................................... 3-34
3.7.11 Serial ATA (SATA) 3.0 Connectors .................................... 3-36
3.7.12 SATA Power Connectors ................................................... 3-37
3.7.13 Power Input Connector ..................................................... 3-38
3.7.14 DC Power Input Connector ............................................... 3-38
3.7.15 LVDS Connector ............................................................... 3-39
3.7.16 LVDS Inverter Connector .................................................. 3-39
3.7.17 PCI Express Slot (x4) ....................................................... 3-40
3.7.18 Control Signal Connector .................................................. 3-41
3.7.19 I2C Wafer (optional) .......................................................... 3-42
3.7.20 Power Button Connectors ................................................. 3-42
3.7.21 Panel Power LED Connector ............................................ 3-43
3.7.22 Panel HDD LED Connector .............................................. 3-43
3.7.23 Low Pin Count (LPC) Connector ...................................... 3-44
3.7.24 CompactFlash Card Connector ........................................ 3-45
3.7.25 SIM Card Slot .................................................................... 3-46
3.7.26 Hardware Power Failure Selection ................................... 3-46
3.7.27 CFast Vol tage Control Selection ....................................... 3-47
3.7.28 LVDS Resolution Selection ............................................... 3-48
3.7.29 LVDS Voltage Selection .................................................... 3-51
3.7.30 Flash Descriptor Override Selection ................................. 3-51
3.7.31 VCCIO Voltage Selection .................................................. 3-52
ii
BIOS Recovery Mode Selection ....................................... 3-52
3.7.32
3.7.33 Clear CMOS Data Selection ............................................. 3-53
3.8 TOUCH CONTROL BOARD SR-6145 CONNECTOR QUICK
REFERENCE TABLE ............................................................... 3-54
3.9 TOUCH CONTROL BOARD SR-6145 COMPONENT
LOCATIONS ............................................................................. 3-54
3.9.1 Touch Control Board SR-6145 Top View .......................... 3-54
3.10 SETTING TOUCH CONTROL BOARD SR-6145 CONNECTORS
AND JUMPERS ....................................................................... 3-55
3.10.1 Control Signal Connector .................................................. 3-55
3.10.2 LVDS Panel Signal Connector (Connected To Motherboard) ..
......................................................................................... 3-56
3.10.3 LVDS Panel Signal Connector (Connected To LCD Panel) .....
......................................................................................... 3-57
3.10.4 15" Panel LED Backlight Control Connector .................... 3-58
3.10.5 Touch Panel Connector .................................................... 3-58
3.10.6 LED1 Connector ............................................................... 3-59
3.10.7 Touch Panel Up Signal Setting ......................................... 3-60
3.10.8 Touch Panel Low Signal Setting ....................................... 3-61
4 Software Utilities ................................................................................. 4-1
4.1 Introduction................................................................................. 4-2
4.2 Installing Intel® Chipset Software Installation Utility ................... 4-4
4.2.1 Introduction ......................................................................... 4-4
4.2.2 Intel® Chipset Software Install ati on Uti lity ........................... 4-4
4.3 Intel® Management Engine Components Installer Installation ... 4-5
4.4 Intel® USB 3.0 eXtensible Host Controller Utility ....................... 4-7
4.5 Installing Intel RST Driver Utility (Only for Q170, Optional) ....... 4-8
iii
Intel
4.6
®
RapidStorage Technology Option ROM ........................... 4-8
4.7 Installing Graphics Driver Utility ............................................... 4-10
4.8 Installing LAN Driver Utility ....................................................... 4-11
4.9 Installing Sound Driver Utility ................................................... 4-12
4.10 Installing Touch Driver Utility .................................................... 4-12
4.11 Microsoft Hotfix kb3211320 and kb3213986 Driver installation ......
................................................................................................ 4-13
5 BIOS SETUP ........................................................................................ 5-1
5.1 Introduction................................................................................. 5-2
5.2 Accessing Setup Utility ............................................................... 5-3
5.3 Main ............................................................................................ 5-6
5.4 Advanced ................................................................................... 5-8
5.4.1 Advanced – CPU Configur atio n .......................................... 5-9
5.4.2 Advanced – PCH-FW Configuration ................................. 5-11
5.4.3 Advanced – Trusted Computing ....................................... 5-12
5.4.4 Advanced – ACPI Settings ................................................ 5-13
5.4.6 Advanced – SATA Configuration ....................................... 5-14
5.4.7 Advanced – Hardware Monitor ......................................... 5-15
5.4.8 Advanced – F81866 Watchdog Configuration .................. 5-16
5.4.9 Advanced – F81866 Super IO Conf igura ti on .................... 5-17
5.4.10 Advanced – Network Stack Configuration ........................ 5-23
5.4.11 Advanced – USB Configuration ........................................ 5-25
5.5 Chipset ..................................................................................... 5-26
5.5.1 Chipset – System Agent (SA) Configuration ..................... 5-27
5.5.2 Chipset – PCH-IO Configuration ....................................... 5-32
iv
Security .................................................................................... 5-38
5.6
5.7 Boot .......................................................................................... 5-40
5.7.1 Boot – Network Device BBS Priorities .............................. 5-42
5.7.2 Boot – Hard Drive BBS Priorities ...................................... 5-43
5.7.3 Boot – CSM Configuration ................................................ 5-44
5.8 Save & Exit ............................................................................... 5-46
Appendix A System Diagrams .................................................... A-1
SP-7165 Equipped Module PC Explo ded Diagr am ..................................A-2
SP-7167 Equipped Module PC Explo ded Diagr am ..................................A-3
SP-7165 LCD Display Exploded Diagram (5-Wire Resistive T ouch Screen)
..................................................................................................................A-4
SP-7165 LCD Display Exploded Diagram (Projected Touch Screen) ......A-6
SP-7167 LCD Display Exploded Diagram (5-Wire Resistive T ouch Screen)
..................................................................................................................A-8
SP-7167 LCD Display Exploded Diagram (Projected Touch Screen) ....A-10
SP-7165/SP-7167 Module PC Exploded Diagram .................................A-12
SP-7165/SP-7167 1st Memory Slot & CPU Installation Exploded Diagram
................................................................................................................A-14
SP-7165/SP-7167 2nd Memory Slot and SSD Installation Exploded
Diagram ..................................................................................................A-15
SP-7165 Panel Mount Exploded Diagrams ............................................A-16
SP-7167 Panel Mount Exploded Diagrams ............................................A-17
Appendix B Technical Summary ................................................ B-1
System Block Diagram .............................................................................B-2
Interrupt Map ............................................................................................B-3
I/O Map ...................................................................................................B-20
Memory Map ...........................................................................................B-23
v
Configuring WatchDog Timer .................................................................B-25
Flash BIOS Update .................................................................................B-27
vi
Version No.
Revision History
Page No.
Date
M1
Initial Release
-
2018/01
Revision History
The revision history of SP-7165/SP-7167 User Manual is described below:
vii
SP-7165/SP-7167 SERIES USER MANUAL
Page: 1-1
1 Introduction
This chapter provides the introduction for the SP-7165 /
SP-7167 system as well as the framework of the user
manual.
The following topic is included:
• About This Manual
SP-7165/SP-7167 SERIES USER MANUAL
Page: 1-2
Chapter 1 Introduction
1.1 About This Manual
Thank you fo r purchasi ng our SP-7165/SP-7167 system. T he SP-7165/SP-7167 is an
updated system designed to be comparable with the highest performance of IBM AT
personal computers. The SP-7165/SP-7167 provides faster processing speed, greater
expandability and can handle more tasks than before. This manual is designed to
assist you how to install a nd set up the whole system. It contains 5 chap ters and 2
appendixes. Users can configure the system according to their own needs. T his user
manual is intende d for service personnel with s trong hardware background. It is not
intended for general users.
The following section describes the structure o f th is u ser manual.
Chapter 1 Introduction
This chapter introduces the framework of this user manual.
Chapter 2 Getting Started
This chapter describes the package contents and system specifications, and illustrates
the physical appearances fo r the SP-7165/SP-7167 system. Read the safety re minder s
carefully on how to take care of your system properly.
Chapter 3 System Configuration
This chapter describes the locations and functions of the system motherboard
components. You will learn how to properly configure the connectors and system
configuration jumpers on the motherboard and configure the system to meet your own
needs.
Chapter 4 Software Utilities
This chapter contains helpfull information for proper installatio ns of the Intel Chipset
Software Installation Utility, Intel Management Engine Components Installer Driver
Utility, Intel USB 3.0 Extensible Host Controller Driver Utility, Graphics Driver
Utility, LAN Driver Utility, Sound Driver Utility, KMDF Driver Utility (Windows 7
Only), Intel RST Driver Utility (optional, only for Q170 SKU), Touch Driver Utility
and Hotfix Driver Utilit y.
Chapter 5 BIOS Setup
This chapter provides BIOS setup information.
ppendix A System Assembly Diagrams
A
This appe ndix provides the exploded diagrams and part numbers of the
SP-7165/SP-7167.
Appendix B Technical Summary
This appendix provides the info rmation about the system block diagram, allocation
maps for system resources, Watchdog Timer Configuration and Flash BIOS Update.
SP-7165/SP-7167 SERIES USER MANUAL
Page: 2-1
2 Getting Started
This chapter provides the information for the SP-7165 /
SP-7167 system. It describes how to set up the system
quickly and outlines the system specifications.
The following topics are included:
• Package List
• System Overview
• System Specification
• Safety Precautions
Experienced users can go to Chapter 3 System
Configuration on page 3-1 for a quick start.
SP-7165/SP-7167 SERIES USER MANUAL
Page: 2-2
Item
Q’ty
SP-7165/SP-7167
1
Manual / Driver DVD
1
Quick Guide
1
Chapter 2 Getting Started
2.1 Package List
If you discover any of the items listed below are damaged or lost, please
contact your local distr ib u t o r immediately.
SP-7165/SP-7167 SERIES USER MANUAL
Page: 2-3
2.2 System Overview
SP-7165
Front View Rear View
Chapter 2 Getting Started
Unit: mm
Top View
SP-7165/SP-7167 SERIES USER MANUAL
Page: 2-4
Side View
Chapter 2 Getting Started
SP-7165/SP-7167 SERIES USER MANUAL
Page: 2-5
Bottom View
Quarter View
Chapter 2 Getting Started
SP-7165/SP-7167 SERIES USER MANUAL
Page: 2-6
SP-7167
Front View Rear View
Chapter 2 Getting Started
Unit: mm
Top View
SP-7165/SP-7167 SERIES USER MANUAL
Page: 2-7
Side View
Chapter 2 Getting Started
SP-7165/SP-7167 SERIES USER MANUAL
Page: 2-8
Bottom View
Quarter View
Chapter 2 Getting Started
SP-7165/SP-7167 SERIES USER MANUAL
Page: 2-9
System
CPU
Intel Celeron® G3900TE, Dual Core, 2.3GHz, 2M cache
Chipset
Intel® Q170/ H110
Memory Support
2 x DDR4 2133MHz SO-DIMM up to 32GB
Watchdog
1 ~ 255 seconds Watchdog timer selectable
Drive Bay
(support RAID 0/1 in Q170 SKU only)
Audio
1 x Line-in / 1 x Line-out / 1 x Mic-in
Expansion Slot
1 x CFast slot
System Weight
SP-7167: 10.9 kg
Operating System
Linux Ubuntu 16.04
Dimension (W x H x D)
SP-7167: 434 x 366 x 126.6mm
Power Input
DC in 9~36V
Mounting Support
Wall mount / VESA 100 / Panel mount
Certificate
FCC / CE
I/O Ports (Top side)
SIM Card
1 x SIM card slot
CFast Slot
1 x CFast card slot
Reset
1 x Reset pin
Antenna
3 x antenna holes
I/O Ports (Bottom side)
Display
1 x DVI-I (DVI-D+VGA)
USB
4 x USB 3.0
Serial Port
COM3/4 for RS232
2.3 System Specifications
Intel CoreTM i7-6700TE, Quad Core, 2.4GHz, 8M cache
Intel CoreTM i5-6500TE, Quad Core, 2.3GHz, 6M cache
Support
Intel CoreTM i3-6100TE, Quad Core, 2.7GHz, 4M cache
Intel Pentium® G4400TE,Dual Core, 2.4GHz, 3M cache
Chapter 2 Getting Started
2 x 2.5” SATAIII HDD/SSD
1 x Full-sized mini-PCIe (mini PCIe, USB and SIM
signals)
1 x Half-sized mini-PCIe (mini PCIe and USB signals)
1 x SIM card slot
SP-7165: 8.9 kg
Windows 7 (64-bit)
Windows 8.1 (64-bit)
Windows 10 loT LTSB 2016 (64-bit)
SP-7165: 408 x 320 x 121.6mm
COM1/2 for RS232/422/485 (selectable by BIOS)
COM1/2 for +5V/+12V/RI selectable by jumper
LAN
Digital I/O Port
I2C Bus
Audio
Power Input
LED
Power On/Off
2 x GbE LAN, Wake-On-LAN, PXE
LAN 1: Intel
LAN 2: Intel
8 in / 8 out, DSUB-25 type or 16-pin terminal block
(optional)
1x I2C bus port (optional)
1 x Line-in / 1 x Line-out / 1 x Mic-in
DC in 9~36V
(DIN type 4-pin connector or 3-pin terminal block)
1 x Power LED, 1 x HDD LED, 2 x PoE active LED
(optional)
1 x power button, 1 x remote switch
®
PHY I219 LM (10/100/1000 Mbps)
®
LAN I210 AT (10/100/1000 Mbps)
Display
SP-7165: 15” TFT LCD(LED)
LCD
Resolution XGA 1024 x768
SP-7167: 17” TFT LCD(LED)
Resolution SXGA 1280 x 1024
Touch Screen
5-wire resistive touch screen or projected
(USB interface)
Environment
Operating Temperature
(with airflow)
Storage Temperature -20°C ~ 80°C (-4°F ~ 176°F)
Humidity 20%~ 90%
SSD: (without PoE) 0°C ~ 45°C (32°F ~ 113°F)
(with PoE) 0°C ~ 40°C (32°F ~104°F)
Chapter 2 Getting Started
SP-7165/SP-7167 SERIES USER MANUA L
Page: 2-10
SP-7165/SP-7167 SERIES USER MANUAL
Page: 2-11
Chapter 2 Getting Started
2.4 Safety Precautions
Before operating this system, read the follo wing information carefully to protect your
systems from damages, and extend the life cycle of t he system.
1. Check the Li ne Voltage
• The oper ating voltage for the power suppl y should be within the range of
100V to 240V AC; otherwise, the system may be damaged.
2. Environmental Conditions
• Place your SP-7165/SP-7167 on a sturdy, level surface. Be sure to allow
enough space around the system to have easy access needs.
• Avoid installing your SP-7165/SP-7167 system in extremely hot or cold
places.
• Avoid direct sunlight exposure for a long period of time (for example, in a
closed car in summer time. Also avoid the system from any heating device.).
Or do not use SP-7165/SP-7167 when it has been left outdoors in a cold
winter day.
• Avoid moving the system rap idly fr om a hot place to a cold place, and vice
versa, because condensation may occur inside the system.
• Protect your SP-7165/SP-7167 from strong vibrations which may cause
hard disk fa ilure.
• Do not place the system too close to any radio-active device. Radio-active
device may cause signal interference.
• Always shut d own the operating system before turning off the power.
3. Handling
• Avoid placing heavy objects on the top of the system.
• Do not turn the system upside down. This may cause the hard drive to
malfunction.
• Do not allow any objects to fall into this device.
• If water or other liquid spills into the device, unplug the power cord
immediately.
4. Good Care
• When the outside case gets stained, remove the stains using neutra l washing
agent with a d ry cloth.
• Never use strong agents such as benzene and thinner to clean the surface of
the case.
• If heavy stains are present, moisten a cloth with diluted neutral washing
agent or alcohol and then wipe thoroug hly with a dry cloth.
• If dust is accumulated on the case surface, remove it by using a special
vacuum cleaner for computers.
SP-7165/SP-7167 SERIES USER MANUAL
Page: 3-1
3 System Configuration
This chapter contains helpful information about the jumper
& connector settings, and component locations for the main
board.
The following topics are included:
• SP-7165/SP-7167 Bottom I/O Ports Diagrams
• Connector & Jumper Quick Reference Table
• System Main Board Component Locations
• How to Set Jumpers
• Setting Main Board Connectors and Jumpers
• Touch Control Board Component Locations
• Setting Touch Control Board Connectors and
Jumpers
SP-7165/SP-7167 SERIES USER MANUAL
Page: 3-14
Chapter 3 System Configuration
3.1 External I/O Ports Diagram
3.2 SP-7165/SP-7167 Bottom I/O Ports Diagram
For SP-7165/SP-7167Rx-x0x
For SP-7165/SP-7167Rx-x1x
SP-7165/SP-7167 SERIES USER MANUAL
Page: 3-15
CONNECTOR Description
NAME
Clear CMOS Data Selection
CMOS1
LVDS Panel Selection
JP1, JP2
LVDS Power Selection
JP3
BIOS Recovery Mode Selection
JP4
Flash Descriptor Override Selection
JP7
CFast Voltage Control Selection
JP9
COM1 Pin9 RI/5V/12V Selection
JP12
COM2 Pin18 RI/5V/12V Selection
JP15
Hardware Power Failure Selection
JP16
VCCIO Voltage Selection
JP17
CONNECTOR Description
NAME
Mainboard Front Side Connectors
COM Port
COM1, COM2, COM3, COM4
LAN1, LAN2 Ports
LAN1, LAN2
4 x 1 USB 3.0 Connectors
USB1
(Optional) Digital Input/ Output
Connector
DIO1
DVI-I Connector
DVI1
HD Audio Connector
AUDIO1
Full-Sized Mini PCI Express Slot
M_PCIE1
Half-Sized Mini PCI Express Slot
M_PCIE2
SATA 3.0 Connectors
SATA1, SATA2
SATA Power Connectors
SATA_PWR1, SATA_PWR2
Power Input Connector
PWR_IN1
DC Power Input Connector
ATX_PWR1
LVDS Connector
LVDS1
LVDS Inverter Connector
INV1
PCIe Slot x4
PCI_E1
Control Signal Connector
SGN_BRD1
I2C Wafer (optional)
I2C1
Power Button Connector
PWR_BTN1
Remote Switch Connector
PWR_BTN2
Chapter 3 System Configuration
3.3 Jumper & Connector Quick Reference Table
SP-7165/SP-7167 SERIES USER MANUAL
Page: 3-16
CONNECTOR Description
NAME
Panel Power LED Connector
PWRLED1
Panel HDD LED Connector
HDDLED1
Low Pin Count (LPC) Connector
JLPC1
CFast Card Slot
CFAST1
DDR4 SO-DIMM memory socket
SO-DIMM1
Mainboard Rear Side Connector
SIM Card Slot
SIM1
DDR4 SO-DIMM memory socket
SO-DIMM2
Chapter 3 System Configuration
SP-7165/SP-7167 SERIES USER MANUAL
Page: 3-17
Chapter 3 System Configuration
3.4 Component Locations Of System Main Board
3.4.1 Top View and Jumper Settings of SB-8400
Figure 3-1. Main Board Component Location (Top View)
SP-7165/SP-7167 SERIES USER MANUAL
Page: 3-18
WARNING: Always disconnect the power cord when you are
working with connectors and jumpers on the main board.
Make sure both the system and peripheral devices are
turned OFF as sudden surge of power could damage
sensitive components. Make sure SP-7165/SP-7167 is
properly grounded.
CAUTION: Observe precautions while handling electrostatic
sensitive components. Make sure to ground yourself to
prevent static charge while you are working on the
connectors and jumpers. Use a grounding wrist strap and
place all electronic components in any static-shielded
devices.
CAUTION: Always touch the motherboard components by
the edges. Never touch components such as a processor by
its pins. Take special cares while you are holding electronic
circuit boards by the edge s on l y . D o not tou ch the mainboard
components.
Chapter 3 System Configuration
SP-7165/SP-7167 SERIES USER MANUAL
Page: 3-19
3.4.2 Bottom View of SB-8400
Chapter 3 System Configuration
Figure 3-2. Main Board Component Location (Rear View)
Loading...