Protech ProX-1715 User Manual

USER’S
MANUAL

ProX-1715

Pentium® 4
Full-size CPU Card
With VGA/Sound/LAN

Prox-1715 M2

ProX-1715 Pentium® 4

Full-size CPU Card

With VGA/Sound/LAN

OPERATION MANUAL

COPYRIGHT NOTICE

This operation manual is meant to assist both Embedded Computer
manufacturers and end users in installing and setting up the system. The
information contained in this document is subject to change without any
notice.

This manual is copyrighted in October 28, 2002. Revised Edition: Mar. 24,

2003. You may not reproduce or transmit in any form or by any means,
electronic, or mechanical, including photocopying and recording.

ACKNOWLEDGEMENTS

All trademarks and registered trademarks mentioned herein are the
property of their respective owners.

CE NOTICE

This is a class A product. In a domestic environment this product may
cause radio interference in which case the user may be required to take
adequate measures.

Copyright Notice

Copyright Notice

FCC NOTICE

This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.

You are cautioned that any change or modifications to the equipment not
expressly approve by the party responsible for compliance could void
your authority to operate such equipment.

Contents

TABLE OF CONTENTS

CHAPTER 1 INTRODUCTION

1-1 About This Manual ........................................................ 1-2

1-2 System Specification ...................................................... 1-3

1-3 Safety Precautions ......................................................... 1-6

CHAPTER 2 HARDWARE CONFIGURATION

2-1 Jumper & Connector Quick Reference Table ................ 2-2

2-2 Component Locations .................................................... 2-3

2-3 How to Set the Jumpers ................................................. 2-4

2-4 COM Port Connector ……..…………………………... 2-6

2-5 RS232/422/485 (COM2) Selection ............................... 2-7

2-6 Solid-State Disk Socket ..................................………... 2-8

2-7 SSD Memory Mapping Selection .................................. 2-9

2-8 Keyboard or PS/2 Mouse Connector .....................….... 2-10

2-9 Keyboard or PS/2 Mouse Selection .......................….... 2-10

2-10 External Keyboard Connector ....................................... 2-11

2-11 Reset Connector ............................................................ 2-11

2-12 Hard Disk Drive LED Connector .................................. 2-12

2-13 ATX Power Button ….................................................... 2-12

2-14 External Speaker Connector .......................................... 2-13

2-15 Power Led Connector ……............................................ 2-13

2-16 KeyLock Connector ..………………………………… 2-14
2-17 Clear CMOS Data Selection ………………………….. 2-14
2-18 CPU Fan Connector ………………………………….. 2-15
2-19 VGA CRT Connector ………………………………… 2-15
2-20 PanelLink Connector ….…..………………………….. 2-16
2-21 LVDS Connector ……………………………………... 2-17

2-22 Hard Disk Drive Connector ........................................... 2-18

2-23 Floppy Disk Drive Connector ....................................... 2-20

2-24 Printer Connector .......................................................... 2-21

2-25 Universal Serial Bus Connector ……………………… 2-22
2-26 IrDA Connector …..………………………………….. 2-22
2-27 LAN Connector ………………………………………. 2-23
2-28 ATX Power Signal Connector ……….……………… 2-23

Contents

2-29 ATX +12V Power Connector ......................................... 2-24

2-30 Reset / NMI / Clear Watchdog Selection ……….…….. 2-24
2-31 Panel VDD Selection …………………………….……. 2-25
2-32 LVDS Power Connector ……………..………….…….. 2-25
2-33 Panel Type Selection …………………………….……. 2-26
2-34 Sound Connector ………………………………………. 2-27
2-35 CD-IN Connector ……………………………………… 2-27
2-36 PPCI Connector ……………….……………….………. 2-28
2-37 Memory Installation …..……………………….………. 2-29

CHAPTER 3 SOFTWARE UTILITIES

3-1 Introduction …………..........................................…....... 3-2

3-2 VGA Driver Utility ……………………………….…… 3-3

3-3 Flash BIOS Update ..............................................…....... 3-4

3-4 LAN Driver Utility …...........................................…...... 3-6

3-5 Sound Driver Utility …...........................................….... 3-7

3-6 Intel Chipset Software Installation Utility …..……..….. 3-8
3-7 USB2.0 Chipset Software Installation Utility …………. 3-9
3-8 SCSI and STORAGE_ATA Software Installation ……. 3-10

3-9 Watchdog Timer Configuration ..................................… 3-12

CHAPTER 4 AWARD BIOS SETUP

4-1 Introduction ................................................................... 4-2

4-2 Entering Setup ............................................................... 4-3

4-3 The Standard CMOS Features ………............................ 4-4

4-4 The Advanced BIOS Features ....................................... 4-8

4-5 Advanced Chipset Features ........................................... 4-11

4-6 Integrated Peripherals …............................................... 4-14

4-7 Power Management Setup ............................................. 4-18

4-8 PNP/PCI Configuration …............................................. 4-20

4-9 PC Health Status …….................................................... 4-22

4-10 Frequency Control ....................................…………...... 4-23

4-11 Load Fail-Safe Defaults ................................................. 4-24

4-12 Load Optimized Defaults .........................................…. 4-24

4-13 Password Setting ……………………………………… 4-25

4-14 Save & Exit Setup ......................................................... 4-26

4-15 Exit Without Saving ………………………………… 4-27

Contents

APPENDIX A EXPANSION BUS

ISA Bus Pin Assignment ..............................................…......... A-2

PCI Bus Pin Assignment ..............................................….......... A-3

APPENDIX B TECHNICAL SUMMARY

Block Diagram ........................................................................... B-2

Interrupt Map ............................................................................ B-3

RTC & CMOS RAM Map ........................................................ B-4

Timer & DMA Channels Map .................................................. B-5

I/O & Memory Map ...............................................…................ B-6

APPENDIX C TROUBLE SHOOTING

Trouble Shooting for Error Messages ........................…............ C-2

Trouble Shooting for POST Codes ............................................ C-8

Contents

INTRODUCTION

This chapter gives you the information for Prox-1715. It also
outlines the System specification.

Section includes:

z About This Manual

z System Specifications

z Safety precautions

Experienced users can skip to chapter 2 on page 2-1
for Quick Start.

CHAPTER

1

Page:1-1

Chapter 1 Introduction

1-1. ABOUT THIS MANUAL

Thank you for purchasing our Prox-1715 Socket 478 Embedded Card
enhanced with VGA / Sound / LAN, which is fully PC / AT compatible. Prox­1715 provides faster processing speed, greater expandability and can handle
more task than before. This manual is designed to assist you how to install and
set up the system. It contains four chapters. The user can apply this manual for
configuration according to the following chapters :

Chapter 1 Introduction

This chapter introduces you to the background of this manual, and the
specification for this system. Final part of this chapter will indicate you how
to avoid damaging this Embedded Card.

Chapter 2 Hardware Configuration

This chapter outlines the component location and their functions. In the end of
this chapter, you will learn how to set jumper and how to configure this card
to meet your own needs.

Chapter 3 Software Utilities

This chapter contains helpful information for proper installations of the VGA
utility, LAN utility, sound utility, and BIOS update. It also describes the
Watchdog timer configuration.

Chapter 4 Award BIOS Setup

This chapter indicates you how to set up the BIOS configurations.

Appendix A Expansion Bus

This Appendix introduces you the expansion bus for ISA Bus and PCI Bus.

Appendix B Technical Summary

This section gives you the information about the Technical maps.

Appendix C Trouble Shooting

This section outlines the error messages and offers you the methods to solve
the problems.

Page: 1-2

Prox-1715 USER

′

S MANUAL

1-2. SYSTEM SPECIFICATION

z CPU (mPGA 478) :

Intel® Pentium® 4 in mPGA478 socket
Available at 1.4, 1.5, 1.6, 1.7, 1.8, 1.9, 2.0, 2.2, 2.4, 2.8, 3.06GHz
System bus frequency at 400MHz/533MHz
Auto detect voltage regulator

z SYSTEM CHIPSET :

Intel® 845E chipset

z MEMORY :

Supports up to 2GB DDR SDRAM.
Supports ECC function.
Two 184-pin DDR DIMM sockets on board

z CACHE :

Built-in CPU

z REAL-TIME CLOCK / CALENDAR :

256-byte battery backed CMOS RAM.
Hardware implementation to indicate century rollover

z BIOS :

Phoenix-AwardBIOS™ for plug & play function
Easy update 512KB flash EEPROM
Supports S/IO setup.

z KEYBOARD/MOUSE CONNECTOR :

Mini DIN connector, selectable for Keyboard, PS/2 Mouse, or Y-Cable
One additional 5-pin External keyboard connector

z UNIVERSAL SERIAL BUS :

Universal Serial Bus Connector on board
Supports up to two USB 2.0 ports.

z DISK-ON-CHIPS SOCKET :

One 32-pin socket supports up to 288MB disk-on-chip.

Chapter 1 Introduction

Prox-1715 USER′S MANUAL

Page: 1-3

Chapter 1 Introduction

z BUS SUPPORT :

External ISA/PCI BUS; PICMG Spec
External PPCI Bus

z DISPLAY :

ATI Rage M6, 16MB internal memory, 4X AGP Bus.
Fully support multi-display of CRT, LVDS & PanelLink™.
Interface: 15-pin CRT connector supports up to 1600x1200 UXGA.

Two 21-pin LVDS connector support up to 48 bit.
One 20-pin DFP connector for Digital Flat Panel (PanelLink™).

z WATCHDOG :

I / O port 0443H to Enable watchdog.
I / O port 0441H to Disable watchdog.
Watchdog function is selectable for Reset or NMI function.
Time-out timing select 0 / 8 / sec +/- 4%, 16 / 24 / 32 / 40 / 48 / 56 / 64 / 72 /
80 / 88 / 96 / 104 / 112 / 120 sec +/- 25%.

z IDE INTERFACE :

Two IDE ports support up to four IDE devices.
Supports Ultra ATA-33/66/100.

z FLOPPY DISK DRIVER INTERFACE :

Supports up to two Floppy Disk Drives, 3.5" and 5.25".

z LAN INTERFACE :

Intel® 82562EM PHY PCI Fast Ethernet
One RJ-45 Jack onboard
Supports 10BaseT/100BaseTX PCI Ethernet.
Supports Wake-On-LAN function, when use ATX power 5VSB.

z SERIAL PORT :

Two high speed 16550 Compatible UARTs with Send / Receive 16 Byte
FIFOs. COM1 for RS232; COM2 for RS232/422/485.
Programmable Baud Rate Generator

Page: 1-4

Prox-1715 USER

′

S MANUAL

z SOUND INTERFACE :

AC '97 Codec
Fully Compliant AC '97 Analog I/O Component
Interface: Line-In, Line-Out, Microphone, and CD Audio-In.

z PARALLEL PORT :

One port supports SPP / ECP / EPP Function.

z HARDWARE MONITORING FUNCTION :

Monitor Voltage, CPU Temperature and Cooling Fan.

z IRDA PORT :

One 5-pin Infrared connector
Supports IrDA v1.0 SIR protocol.

z LED INDICATOR :

System power
Hard Disk access
LAN LED indicator

z DMA CONTROLLER :

82C37 x 2

z DMA CHANNELS :

7

z INTERRUPT CONTROLLERS :

82C59 x 2

z INTERRUPT LEVELS :

15

z OPERATING TEMPERATURE :

0 to 60°C (32°F to 140°F)

Chapter 1 Introduction

Prox-1715 USER′S MANUAL

Page: 1-5

Chapter 1 Introduction

z SYSTEM POWER REQUIREMENT :

DC Voltage: +5V, minimum +4.75V, maximum +5.25V.
DC Ampere: 3A.
DC Voltage: +12V, minimum +11.4V, maximum +12.6V.
DC Ampere: 5.2A.

z BOARD DIMENSION :

338.5mm x 122mm (13.3” x 4.8”)

z BOARD NET WEIGHT :

386 grams (0.85 lb)

1-3. SAFETY PRECAUTIONS

Follow the messages below to avoid your systems from damage:

1. Avoid your system from static electricity on all occasions.

2. Prevent electric shock. Don‘t touch any components of this card when the
card is power-on. Always disconnect power when the system is not in use.

3. Disconnect power when you change any hardware devices. For instance,
when you connect a jumper or install any cards, a surge of power may
damage the electronic components or the whole system.

Page: 1-6

Prox-1715 USER

′

S MANUAL

HARDWARE
CONFIGURATION

** QUICK START **

Helpful information describes the jumper & connector settings, and
component locations.

Section includes:

 Jumper & Connector Quick Reference Table

 Component Locations

 Configuration and Jumper settings

 Connector’s Pin Assignments

CHAPTER

2

Page 2-1

Chapter 2 Hardware Configuration

2-1. JUMPER & CONNECTOR QUICK REFERENCE TABLE

COM Port Connector ....................…..................……… COM1, COM2

RS232/422/485 (COM2) Selection .....................……… JP6

Solid-State Disk Socket ...............…...................……… SSD

SSD Memory Mapping Selection .................…....…….. JP9, JP10

Keyboard or PS/2 Mouse Connector ..........….......…… DIN

Keyboard or PS/2 Mouse Selection .........…...........…… JP12

External Keyboard Connector .............................……… EXKB

Reset Connector .........................…....................………. JP1

Hard Disk Drive LED Connector .......................………. JP1

ATX Power Button …………………………………….. JP1

External Speaker Connector ....…........................……… JP1

Power LED Connector …………….…...............……… JP1

KeyLock Connector ……………………………………. JP1
Clear CMOS Data Selection …………………………… JP5
CPU Fan Connector …………………………………… FAN1

VGA CRT Connector .....................…................………. VGA

PanelLink Connector …………………………………... TMDS
LVDS Connector ………………………………………. LVDS1, LVDS2

Hard Disk Drive Connector .................…............……... IDE1, IDE2

Floppy Disk Drive Connector ................…..........…….. FDD1

Printer Connector ...............................…............………. LPT1

Universal Serial Bus Connector ...........................…..…. USB1

IrDA Connector ……………………………………….. IrDA1

LAN Connector .......................................….......………. UPT1

ATX Power Connector ………………………………… PW1
ATX Power Signal Connector …..…………………….. JP8
ATX +12V Power Connector …………………………. CN1
Reset/NMI/Clear Watchdog Selection .………….…….. JP7
Panel VDD Selection ………………………………….. JP11
LVDS Power Connector ……………………………... JP3
Panel Type Selection ………………………………….. JP2
Sound Connector ………………………….…………… JP4
CD Audio-In Connector ……………………………….. CD-IN
PPCI Connector ……………..………………….……… PPCI

Memory Installation ..................................…......……… DIMM1, DIMM2

(18,20)
(12,14)

(13,15)
(2,4,6,8)
(1,3,5)
(7,9)

Page: 2-2

Prox-1715 USER

′

S MANUAL

V

Chapter 2 Hardware Configuration

2-2. COMPONENT LOCATIONS

2
M
O
C

1

2

COM1

9

5

2

4
P
J

1

0

9

1

UPT1

1

7

6

1

8

2

0

1

2

0

2

9

1

1

1

1

6

N
I

-

P
J

D

9
1

C

EXKB

GA

DIN

5

1
1

6

1

1

4

2

1

3

1
0
1

5

6

5

1

5

JP12

2

6

1
D

1

D

T
P

F

L

4

333

1
E
D

I

1

1
P
J

5

USB1

9

0

1

2

2
M

M
I

D

7
2
6
3
8

5
P
J

2

Z

E

U

D

I

B

1
1

1

S
D
M
T

6

3

1

P
J

2
P
J

5

1

0
1

1
M

M
I

D

2
6
5
2
8

1

7

2

P

1

J

2

1

0

1

A
D
r

I

1

1

0

2

2

1
S
D
V
L

2

1
1

0

2

2

2
S
D
V
L

2

1

8
7
4
A
G
P

M

E

1
P

T

J

I

2

9
P
J

L

5
4

E

8

T

2
N

I

8

1

1

B

F
8
8
8
8
T

I

L
E
T
N

I

A

I
C
P
P

0

0
3

3
A

B

1
0
8
2
8

1

1

N
A
F

0

5

1

1
W
P

1

6

3

1

1
N
C

2

4

Prox-1715 Connector, Jumper and Component locations

Prox-1715 USER′S MANUAL

Page: 2-3

Chapter 2 Hardware Configuration

2-3. HOW TO SET THE JUMPERS

You can configure your board by setting jumpers. Jumper is consists of
two or three metal pins with a plastic base mounted on the card, and by
using a small plastic "cap", Also known as the jumper cap (with a metal
contact inside), you are able to connect the pins. So you can set-up your
hardware configuration by "open" or "close" pins.

The jumper can be combined into sets that called jumper blocks. When the
jumpers are all in the block, you have to put them together to set up the
hardware configuration. The figure below shows how this looks like.

JUMPERS AND CAPS

If a jumper has three pins (for examples, labelled PIN1, PIN2, and PIN3),
You can connect PIN1 & PIN2 to create one setting and shorting. You can
either connect PIN2 & PIN3 to create another setting. The same jumper
diagrams are applied all through this manual. The figure below shows what
the manual diagrams look and what they represent.

Page: 2-4

Prox-1715 USER

′

S MANUAL

JUMPER DIAGRAMS

JUMPER SETTINGS

Chapter 2 Hardware Configuration

Jumper Cap
looks like this

2 pin Jumper
looks like this

3 pin Jumper
looks like this

Jumper Block
looks like this

2 pin Jumper close(enabled)

1

1

1

2

Prox-1715 USER′S MANUAL

Looks like this

3 pin Jumper

2-3 pin close(enabled)

Looks like this

Jumper Block

1-2 pin close(enabled)

Looks like this

1

1

12

Page: 2-5

Chapter 2 Hardware Configuration

2-4. COM PORT CONNECTOR

COM1 : COM1 Connector
COM1 is fixed as RS-232.
The pin assignment is as follows :

PIN ASSIGNMENT

1 DCD
2 RX
3 TX
4 DTR
5 GND
6 DSR
7 RTS
8 CTS
9 RI

COM2 : COM2 Connector
The COM2 is selectable as RS-232/422/485.
The pin assignment is as follows :

COM1

Page: 2-6

PIN

ASSIGNMENT

RS-232 RS-422 RS-485

1 DCD TX- TX­2 RX TX+ TX+
3 TX RX+ RX+
4 DTR RX- RX­5 GND GND GND
6 DSR RTS- NC
7 RTS RTS+ NC
8 CTS CTS+ NC
9 RI CTS- NC

10 NC NC NC

Prox-1715 USER

′

S MANUAL

Chapter 2 Hardware Configuration

2-5. RS232/422/485 (COM2) SELECTION

JP6 : RS-232/422/485 (COM2) Selection
This connector is used to set the COM2 function.
The jumper settings are as follows :

COM 2

Function

RS-232 RS-422 RS-485

Open

Jumper

Settings

(pin closed)

Jumper

Illustrations

*** Manufactory default --- RS-232.

1-2
5-6
7-8

9-10
11-12
13-14
15-16
17-18
19-20

1-3
4-6
7-8

9-10
11-12
13-14
15-16
17-18
19-20

Prox-1715 USER′S MANUAL

Page: 2-7

Chapter 2 Hardware Configuration

2-6. SOLID-STATE DISK SOCKET

SSD: 32pin Disk-on-chip Socket
The pin assignments are as follows:

32

SSD

17

116

PIN ASSIGNMENT PIN ASSIGNMENT

1 NC 17 SD3
2 GND 18 SD4
3 GND 19 SD5
4 SA12 20 SD6
5 SA7 21 SD7
6 SA6 22 CE
7 SA5 23 SA10
8 SA4 24 OE

9 SA3 25 SA11
10 SA2 26 SA9
11 SA1 27 SA8
12 SA0 28 SA13
13 SD0 29 SA14
14 SD1 30 VCC
15 SD2 31 WE
16 GND 32 VCC

Page: 2-8

Prox-1715 USER

′

S MANUAL

Chapter 2 Hardware Configuration

2-7. SSD MEMORY MAPPING SELECTION

JP9, JP10 : SSD Memory Mapping Selections
A 32-pin SSD socket supports Disk-on-Chip up to 288MB. This PnP
Flash ROM SSD can be install as one of user’s hard disk drive.
The SSD Memory Mapping Selections are as follows:

SSD Memory Map

JUMPER SETTING

(pin closed)

ILLUSTRATION

JP9 JP10

JUMPER

781

1

D0000h-D1FFFh 1-2 3-4

D4000h-D5FFFh 3-4 3-4

D8000h-D9FFFh 1-2 5-6

DC000h-DDFFFh 5-6 5-6

*** Manufactory default --- D0000h-D1FFFh.

JP9

JP9

JP9

JP9

234

7

81234

781

234

781

234

JP10

JP10

JP10

JP10

2

1

2

1

2

1

2

Prox-1715 USER′S MANUAL

Page: 2-9

Chapter 2 Hardware Configuration

2-8. KEYBOARD OR PS/2 MOUSE CONNECTOR

DIN : Keyboard or PS/2 Mouse Connector
DIN connector can support keyboard, Y-cable, or PS/2 Mouse, user may
select the right device to used on “Keyboard or PS/2 Mouse Selection”.
The pin assignments are as follows :

PIN

Keyboard PS/2 Mouse

ASSIGNMENT

1 KBDATA MSDATA
2 MSDATA MSDATA
3 GND GND
4 VCC VCC
5 KBCLK MSCLK
6 MSCLK MSCLK

2-9. KEYBOARD OR PS/2 MOUSE SELECTION

JP12 : Keyboard or PS/2 Mouse Selection
For Y-Cable user, please set the jumper same as AT keyboard.
The jumper settings are as follows:

*** Manufactory default -- AT Keyboard

DEVICE

TYPE

KEYBOARD

PS/2 MOUSE

JUMPER SETTING

(pin closed)

3-5
4-6

1-3
2-4

JUMPER

ILLUSTRATION

65

2

JP12

65

2

JP12

6

5

3

4

2

1

DIN

1

1

Page: 2-10

Prox-1715 USER

′

S MANUAL

N

Chapter 2 Hardware Configuration

2-10. EXTERNAL KEYBOARD CONNECTOR

EXKB : External Keyboard Connector
The pin assignment is as follows :

PIN ASSIGNMENT

1 KBCLK

2 KBDATA

3

C
4 GND
5 VCC

2-11. RESET CONNECTOR

JP1 (18,20) : Reset Connector.
The pin assignment is as follows :

19
20

RST

PIN ASSIGNMENT

18 HW RESET
20 GROUND

JP1

1
2

1

EXKB

Prox-1715 USER′S MANUAL

Page: 2-11

Chapter 2 Hardware Configuration

2-12. HARD DISK DRIVE LED CONNECTOR

JP1 (12,14) : Hard Disk Drive LED Connector
The pin assignment is as follows :

19
20

HDD_LED

JP1

1
2

PIN ASSIGNMENT

12 HDD_LED
14 VCC

2-13. ATX POWER BUTTON

JP1 (13,15) : ATX Power Button
The pin assignment is as follows :

19
20

ATX_ BT N

1
2

Page: 2-12

PIN ASSIGNMENT

13 PWR_BN1
15 PWR_BN2

JP1

Prox-1715 USER

′

S MANUAL

Chapter 2 Hardware Configuration

2-14. EXTERNAL SPEAKER CONNECTOR

JP1 (2,4,6,8) : External Speaker Connector
The pin assignment is as follows :

19
20

SPK

JP1

1
2

PIN ASSIGNMENT

2 VCC
4 GND
6 NC
8 SPEAKER SIGNAL

2-15. POWER LED CONNECTOR

JP1 (1,3,5) : Power LED Connector
The pin assignment is as follows:

19
20

PIN ASSIGNMENT

1 PW_LED
3 PW_LED
5 GND

PWR_LED

JP1

1
2

Prox-1715 USER′S MANUAL

Page: 2-13

Chapter 2 Hardware Configuration

2-16. KEYLOCK CONNECTOR

JP1 (7,9) : Keylock Connector
The pin assignment is as follows:

KEYLOCK

19
20

JP1

1
2

PIN ASSIGNMENT

7 KEYLOCK
9 GND

2-17. CLEAR CMOS DATA SELECTION

JP5 : Clear CMOS Data Selection
The selections are as follows :

*** Manufacturing Default is set as Normal.

Note: To clear CMOS data, user must power-off the computer and set the jumper to

Page: 2-14

FUNCTION

JUMPER SETTING

(pin closed)

JUMPER

ILLUSTRATION

Clear CMOS 1-2

Normal 2-3

“Clear CMOS” as illustrated above. After five to six seconds, set the jumper
back to “Normal” and power-on the computer.

Prox-1715 USER

′

S MANUAL

V

2-18. CPU FAN CONNECTOR

FAN1 : CPU Fan connector
The pin assignment is as follows:

PIN ASSIGNMENT

1 GND
2 +12V
3 FAN

2-19. VGA CRT CONNECTOR

VGA : VGA CRT Connector
The pin assignments are as follows:

PIN ASSIGNMENT

1 RED
2 GREEN
3 BLUE
4 MONID0
5 GND
6 GND
7 GND
8 GND
9 VCC

10 GND
11 MONID1
12 VGA DDCDATA
13 HSYNC
14 VSYNC
15 VGA DDC CLK

Chapter 2 Hardware Configuration

FAN1

1

GA

1

6

11

5

10

15

Prox-1715 USER′S MANUAL

Page: 2-15

Chapter 2 Hardware Configuration

2-20. PANELLINK CONNECTOR

TMDS : PanelLink™ Connector
This comprise a 2 electrical layer components: a TMDS interface for low
voltage differential serial encoding of the digital display data and a
DDC2B electrical interface that can be shared with the standard 15-pin
DDC2B compliant VGA connector (if present).
The pin assignments are as follows :

10
20

TMDS

PIN ASSIGNMENT PIN ASSIGNMENT

1 TX OUT1+ 11 TXOUT2+
2 TXOUT1- 12 TXOUT2­3 GND 13 GND
4 GND 14 GND
5 TXCLKOUT+ 15 TXOUT0+
6 TXCLKOUT- 16 TXOUT0­7 GND 17 NC
8 VCC 18 CHARGE
9 NC 19 DVI DATA

10 NC 20 DVI CLK

1

11

Page: 2-16

Prox-1715 USER

′

S MANUAL

2-21. LVDS CONNECTOR

LVDS1 : LVDS Connector
The pin assignments are as follows :

PIN ASSIGNMENT PIN ASSIGNMENT

1 GND 12 TXL1+
2 GND 13 TXL1­3 TXL3+ 14 GND
4 TXL3- 15 TXL0+
5 GND 16 TXL0­6 TXCLKL+ 17 GND
7 TXCLKL- 18 GND
8 GND 19 PANEL VDD

9 TXL2+ 20 PANEL VDD
10 TXL2- 21 CHARGE
11 GND

LVDS2 : LVDS Connector
The pin assignments are as follows :

PIN ASSIGNMENT PIN ASSIGNMENT

1 GND 12 TXU1+

2 GND 13 TXU1-

3 TXU3+ 14 GND

4 TXU3- 15 TXU0+

5 GND 16 TXU0-

6 TXCLKU+ 17 GND

7 TXCLKU- 18 GND

8 GND 19 PANEL VDD

9 TXU2+ 20 PANEL VDD
10 TXU2- 21 CHARGE
11 GND

 24bit and below panel used LVDS1, for 36/48bit panel used

both LVDS1 and LVDS2 connector.

Chapter 2 Hardware Configuration

LVD S 1

2
1

LVD S2

2
1

20
21

20
21

Prox-1715 USER′S MANUAL

Page: 2-17

Chapter 2 Hardware Configuration

2-22. HARD DISK DRIVE CONNECTOR

IDE1: Hard Disk Drive Connector
The Prox-1715 possesses two HDD connectors, IDE1 and IDE2. The pin
assignments are as follows:

39

1

40

2

IDE1

PIN ASSIGNMENT PIN ASSIGNMENT

1 IDERST 2 GND
3 PDD7 4 PDD8
5 PDD6 6 PDD9
7 PDD5 8 PDD10

9 PDD4 10 PDD11
11 PDD3 12 PDD12
13 PDD2 14 PDD13
15 PDD1 16 PDD14
17 PDD0 18 PDD15
19 GND 20 NC
21 PDREQ 22 GND
23 PDIOW# 24 GND
25 PDIOR# 26 GND
27 PIORDY 28 PULL LOW
29 PDDACK# 30 GND
31 IRQ14 32 NC
33 PDA1 34 P66 DETECT
35 PDA0 36 PDA2
37 PDCS#1 38 PDCS#3
39 IDEACTP# 40 GND

Page: 2-18

Prox-1715 USER

′

S MANUAL

IDE2: Hard Disk Drive Connector
The pin assignments are as follows:

39

Chapter 2 Hardware Configuration

1

40

2

IDE2

PIN ASSIGNMENT PIN ASSIGNMENT

1 IDERST 2 GND

3 SDD7 4 SDD8

5 SDD6 6 SDD9

7 SDD5 8 SDD10

9 SDD4 10 SDD11
11 SDD3 12 SDD12
13 SDD2 14 SDD13
15 SDD1 16 SDD14
17 SDD0 18 SDD15
19 GND 20 NC
21 SDREQ 22 GND
23 SDIOW# 24 GND
25 SDIOR# 26 GND
27 SIORDY 28 PULL LOW
29 SDDACK# 30 GND
31 IRQ15 32 NC
33 SDA1 34 S66 DETECT
35 SDA0 36 SDA2
37 SDCS#1 38 SDCS#3
39 IDEACTS# 40 GND

Prox-1715 USER′S MANUAL

Page: 2-19

Chapter 2 Hardware Configuration

2-23. FLOPPY DISK DRIVE CONNECTOR

FDD1 : Floppy Disk Drive Connector
You can use a 34-pin daisy-chain cable to connect two-FDDs. On one
end of this cable is a 34-pin flat cable to attach the FDD on the board, and
the other side is attaches two FDDs.
The pin assignments are as follows :

FDD1

33

1

34

2

PIN ASSIGNMENT PIN ASSIGNMENT

1 GND 2 RWC#

3 GND 4 NC

5 GND 6 DS1#

7 GND 8 INDEX

9 GND 10 MOA#
11 GND 12 DSB#
13 GND 14 DSA#
15 GND 16 MOB#
17 GND 18 DIR#
19 GND 20 STEP#
21 GND 22 WD#
23 GND 24 WE#
25 GND 26 TRK0#
27 GND 28 WP#
29 NC 30 RDATA#
31 GND 32 HEAD#
33 NC 34 DSKCHG

Page: 2-20

Prox-1715 USER

′

S MANUAL

2-24. PRINTER CONNECTOR

PRN : Printer Connector
As to link the Printer to the card, you need a cable to connect both DB25
connector and parallel port.
The pin assignments are as follows :

Chapter 2 Hardware Configuration

LPT1

PIN ASSIGNMENT PIN ASSIGNMENT

1 STB 14 AFD#

2 PDR0 15 ERROR#

3 PDR1 16 PAR_INIT#

4 PDR2 17 SLIN#

5 PDR3 18 GND

6 PDR4 19 GND

7 PDR5 20 GND

8 PDR6 21 GND

9 PDR7 22 GND
10 ACK# 23 GND
11 BUSY 24 GND
12 PE 25 GND
13 SLCT 26 NC

Prox-1715 USER′S MANUAL

Page: 2-21

Chapter 2 Hardware Configuration

2-25. UNIVERSAL SERIAL BUS CONNECTOR

USB1: Universal Serial Bus Connector
This connector can connect up to two USB port.
The pin assignments are as follows:

PIN ASSIGNMENT

1 VCC
2
3 DATA0+

DATA0−

10

4 GND
5 GND
6 VCC
7

DATA1−
8 DATA1+
9 GND

10 GND

2-26. IRDA CONNECTOR

IRDA: IrDA (Infrared) Connector
The pin assignments are as follows:

PIN ASSIGNMENT

1 VCC
2 NC
3 IRRX
4 GND
5 IRTX

5

USB1

IrDA

1
6

1

Page: 2-22

Prox-1715 USER

′

S MANUAL

Chapter 2 Hardware Configuration

2-27. LAN CONNECTOR

LAN1: LAN Connector
The pin assignments are as follows:

PIN ASSIGNMENT

1 TX+
2 TX­3 RX+
4 ISOLATED GND
5 ISOLATED GND
6 RX­7 ISOLATED GND
8 ISOLATED GND
9 LED – SP LED

10 PULL HI
11 LED – LI LED
12 LED – ACT LED

 The green LED detect power link, and the Yellow

LED is used to detect data active transfer signal.

2-28. ATX POWER CONNECTOR

PW1 : ATX Power Connector
The pin assignments are as follows:

PIN ASSIGNMENT

1 VCC
2 VCC
3 GND
4 GND
5 VCC12
6 VCC5_SB
7 VCC
8 GND
9 PS_ON

10 GND

Prox-1715 USER′S MANUAL

1

UPT1

1

2

9

10

Green

8

7

8

1211

Yellow

Page: 2-23

Chapter 2 Hardware Configuration

2-29. ATX POWER SIGNAL CONNECTOR

JP8 : ATX Power Signal Connector
The pin assignments are as follows:

PIN ASSIGNMENT

1 +5V SB
2 GND
3 PS_ON

2-30. ATX +12V POWER CONNECTOR

CN1 : ATX +12V Power Connector
The pin assignments are as follows:

PIN ASSIGNMENT

1 GND
2 GND
3 +12V
4 +12V

2

4

CN1

1

3

Page: 2-24

Prox-1715 USER

′

S MANUAL

Chapter 2 Hardware Configuration

2-31. RESET/NMI/CLEAR WATCHDOG SELECTION

JP7 : Reset/NMI/Clear Watchdog Selection
The selections are as follows:

CLEAR WATCHDOG 5-6

***Manufacturing Default is set as Reset.

 User may select to use the Reset or NMI watchdog. NMI, also known as

Non-Maskable Interrupt, is used for serious conditions that demand the
processor’s immediate attention, it cannot be ignored by the system unless it
is shut off specifically. To clear NMI command, user should short the “Clear
Watchdog” pin via push button.

FUNCTION

JUMPER SETTING

(pin closed)

RESET 1-2

NMI 3-4

JUMPER

ILLUSTRATION

Prox-1715 USER′S MANUAL

Page: 2-25

Chapter 2 Hardware Configuration

2-32. PANEL VDD SELECTION

JP11 Panel VDD Selection
The selections are as follow:

SELECTION

JUMPER SETTING

(pin closed)

JUMPER

ILLUSTRATION

VDD +5V

VDD +3.3V

1-2

2-3

2-33. LVDS POWER CONNECTOR

JP3 : LVDS Power Connector
The pin assignments are as follows:

PIN ASSIGNMENT

1 Safe +12V
2 GND
3 Safe +5V

Note: To change Panel VDD Selection will NOT change the pin

assignment of LVDS Power Connector accordingly to be
+5V or +3.3V. The 3
+5V.

rd

pin on JP3 will be always set as

1

JP3

Page: 2-26

Prox-1715 USER

′

S MANUAL

Chapter 2 Hardware Configuration

2-34. PANEL TYPE SELECTION

JP2: Panel Type Selection
The panel type selections are as follows:

PANEL TYPE

JUMPER SETTING

(pin closed)

JUMPER

ILLUSTRATION

PanelLink™

Open

LVDS

800x600 pixel

1-2

LVDS

1024x768 pixel

3-4

LVDS

1280x1024 pixel

1-2
3-4

***Manufacturing Default – PanelLink™.

 When user intends to use both PanelLink™ and LVDS, the jumper

setting should be set in accordance of the LVDS setting.

Prox-1715 USER′S MANUAL

Page: 2-27

Chapter 2 Hardware Configuration

2-35. SOUND CONNECTOR

JP4 : Sound Connector
The pin assignments are as follows:

PIN ASSIGNMENT

1 MIC-IN
2 GND
3 GND
4 GND
5 LINE-L
6 LINE-R
7 GND
8 GND
9 SPK-L

10 SPK-R

 This connector is to be connected to W-Sound

Adapter Card, for more information, please
refer to Appendix A.

2-36. CD-IN CONNECTOR

CD-IN : CD-In Connector
The pin assignments are as follows:

PIN ASSIGNMENT

1 AUX L
2 GND
3 GND
4 AUX R

9

10 2

JP4

CD-IN

1

1

Page: 2-28

Prox-1715 USER

′

S MANUAL

A

Chapter 2 Hardware Configuration

2-37. PPCI CONNECTOR

You will find a PPCI connector in our Prox-1715. This connector is used

to connect our SCSI daughter boards.

The pin assignments are as follows:

B30

PPCI

B1

A30

1

PIN ASSIGNMENT PIN ASSIGNMENT

A1 GND B1 GND
A2 AD0 B2 AD1
A3 AD2 B3 AD3
A4 AD4 B4 AD5
A5 AD6 B5 AD7
A6 AD8 B6 AD9
A7 AD10 B7 AD11
A8 VCC B8 VCC
A9 AD12 B9 AD13
A10 AD14 B10 AD15
A11 AD16 B11 AD17
A12 AD18 B12 AD19
A13 AD20 B13 AD21
A14 AD22 B14 AD23
A15 VCC B15 VCC
A16 AD24 B16 AD25
A17 AD26 B17 AD27
A18 AD28 B18 AD29
A19 AD30 B19 AD31
A20 PIRQ#B B20 PAR
A21 PP CLK B21 IRDY#
A22 ID SEL B22 TRDY#
A23 CBE#0 B23 CBE#1
A24 CBE#2 B24 CBE#3
A25 PGNT#4 B25 PREQ#4
A26 SERR# B26 PERR#
A27 PIRQ#A B27 PCI_RST#
A28 STOP# B28 PLOCK#
A29 DEVSEL# B29 FRAME#
A30 GND B30 GND

 The PPCI expansion connector of this Card is designed based on PCI

Bus Master. That means when the PPCI expansion connector is used,

th

the 4

PCI slot on the backplane is occupied.

Prox-1715 USER′S MANUAL

Page: 2-29

Chapter 2 Hardware Configuration

2-38. MEMORY INSTALLATION

Prox-1715 CPU Card can support up to 2GB in two DIMM sockets.

DRAM BANK CONFIGURATION

DIMM 1 DIMM 2 TOTAL MEMORY

128MB 128MB 256MB
256MB 256MB 512GB
512MB 512MB 1GB

1GB 1GB 2GB

Page: 2-30

Prox-1715 USER

′

S MANUAL

SOFTWARE

CHAPTER

UTILITIES

This chapter comprises the detailed information of VGA driver, LAN
driver, and Flash BIOS update. It also describes how to install the
watchdog timer configuration.

Section includes:

z VGA Driver Utility

z Flash BIOS Update

z LAN Driver Utility

z Sound Driver Utility

z Intel® Chipset Software Installation Utility

z USB2.0 Chipset Software Installation Utility

z SCSI and STORAGE_ATA Driver Utility

z Watchdog Timer Configuration

3

Page: 3-1

Chapter 3 Software Configuration

3-1. INTRODUCTION

Enclosed with our Prox-1715 package is our driver utility, which may comes
in a form of a CD ROM disc or floppy diskettes. For CD ROM disc user,
you will only need some of the files contained in the CD ROM disc, please
kindly refer to the following chart:

Filename

(Assume that CD ROM drive is D:)

D:\VGA

D:\AWDFLASH For BIOS update utility
D:\LAN Intel® 82562 EM

D:\SOUND Analog Device AD1881 AC97

D:\UTILITY Intel® Chipset Software

D:\USB 2.0 USB 2.0 Software Installation

D:\OPTION For SCSI and STORAGE_ATA

 User should remember to install the Utility right after the OS fully installed.

Purpose

ATI Rage M6
For VGA driver installation

For LAN Driver installation

For Sound driver installation

Installation Utility
For Win 98SE,ME, 2000, XP

Utility
For Win 98SE, 2000, ME, XP

software Installation

Page:3-2

Prox-1715 USER

′

S MANUAL

3-2. VGA DRIVER UTILITY

The VGA interface embedded with our Prox-1715 can support a wide range
of display. You can display CRT, LVDS and PanelLink™ simultaneously
with the same mode.

3-2-1. Installation of VGA Driver:

To install the VGA Driver, simply follow the following steps:

1. Place insert the Utility Disk into Floppy Disk Drive A/B or CD
ROM drive.

2. Under Windows 2000/XP system, go to the directory where VGA
driver is located.

3. Click Setup.exe file for VGA driver installation.

4. Follow the instructions on the screen to complete the installation.

5. Once installation is completed, shut down the system and restart in
order for the changes to take effect.

Chapter 3 Software Configuration

1. Win 98SE program

2. Win NT4.0 program

3. Win 2000 program

4. Win XP program

Prox-1715 USER′S MANUAL

Page:3-3

Chapter 3 Software Configuration

3-3. FLASH BIOS UPDATE

3-3-1. System BIOS Update:

Users of Prox-1715 can use the program “Awdflash.exe” contained in
the Utility Disk for system BIOS and VGA BIOS update.

3-3-2. To update VGA BIOS for LCD Flat Panel Display:

As Prox-1715 user, you have to update the VGA BIOS for your specific
LCD flat panel you are going to use. For doing this, you need two files.
One is the “Awdflash.exe” file and the other is the VGA BIOS for ATI
Rage Mobility M6 file for LCD panel display. Both file must be
provided by the vendor or manufacturer. When you get these two files
ready, follow the following steps for updating your VGA BIOS:

1. Install “Awdflash.exe” from Utility Disk to Drive C.

2. Insert the VGA BIOS file you have obtained from the vendor.
Type the path to Awdflash.exe and execute the VGA BIOS update
with file H15bxxxx.bin

3. C:\UTIL\AWDFLASH>AWDFLASH H15bxxxx.bin

4. The screen will display as the table fount on the next page:

FLASH MEMORY WRITER v7.XX

(C) Award Software 2001 All Rights Reserved

Flash Type – SST 49LF004A /3.3V

File Name to Program: H15bxxxx.bin

Checksum: XXXXX

Page:3-4

Error Message: Do You Want To Save BIOS (Y/N)

If you want to save up the original BIOS, enter "Y" and press < Enter >.
If you choose "N", the following table will appear on screen.

Prox-1715 USER

′

S MANUAL

Chapter 3 Software Configuration

FLASH MEMORY WRITER v7.XX

(C) Award Software 2001 All Rights Reserved

Flash Type – SST 49LF004A /3.3V

File Name to Program: H15bxxxx.bin

Checksum: XXXXX

Error Message : Are You Sure To Program (Y/N)

Select "Y", and the BIOS will be renewed. When you are refreshing the
BIOS, do not turn off or reset the system, or you will damage the BIOS.
After you have completed all the programming, the screen displays the
table below:

FLASH MEMORY WRITER v7.XX

(C) Award Software 2001 All Rights Reserved

Flash Type – SST 49LF004A /3.3V

File Name to Program: H15bxxxx.bin

Checksum: XXXXX

F1: Reset F10: Exit

Please reset or power off the system, and then the Flash BIOS is fully
implemented.

Prox-1715 USER′S MANUAL

Reset System or Power off to

accomplish update process!

Page:3-5

Chapter 3 Software Configuration

3-4. LAN DRIVER UTILITY

3-4-1. Introduction

Prox-1715 is enhanced with LAN function that can support various
network adapters. Installation programs for LAN drivers are listed as
follows:

For more details on Installation procedure, please refer to Readme.txt
file found on LAN DRIVER UTILITY.

1. Win 2000/XP program

2. Win NT4.0 program

3. Linux

4. Netware program

5. Open Server 5.05

6. Unixware 7.x

Page:3-6

Prox-1715 USER

′

S MANUAL

Chapter 3 Software Configuration

3-5. SOUND DRIVER UTILITY

3-5-1. Introduction

The AD1881 sound function enhanced in this system is fully compatible
with Windows 9x, Windows NT 4.0, Windows 2000, Windows ME and
Windows XP. Below, you will find the content of the Sound driver :

1. Win 9x program

2. Win NT 4.0 program

3. Win 2000 program

4. Win ME program

5. Win XP program

3-5-2. Installation Procedure for Windows 9x/NT/2000/XP

1. From the task bar, click on Start, and then Run.

2. In the Run dialog box, type D:\Sound\path\setup, where
“D:\Sound\pathname” refers to the full path to the source files.

3. Click on the OK button or press the ENTER key.

4. Click on the “Next” and OK prompts as they appear.

5. Reboot the system to complete the driver installation.

Prox-1715 USER′S MANUAL

Page:3-7

Chapter 3 Software Configuration

3-6. INTEL® C HIPSET SOFTWARE INSTALLATION UTILITY

3-6-1. Introduction

The Intel® Chipset Software Installation Utility installs to the target
system the Windows* INF files that outline to the operating system how
the chipset components will be configured. This is needed for the
proper functioning of the following features:

- Core PCI and ISAPNP Services

- AGP Support

- IDE/ATA33/ATA66/ATA100 Storage Support

- USB Support

- Identification of Intel® Chipset Components in Device Manager

3-6-2. Installation of Utility for Windows 98SE/ME/2000/XP

The Utility Pack is to be installed only for Windows 98SE, Windows
ME, Windows 2000 and XP program.
It should be installed right after the OS installation, kindly follow the
following steps:

1. Place insert the Utility Disk into Floppy Disk Drive A/B or CD
ROM drive.

2. Under Windows 98SE/ME/2000/XP system, go to the directory
where Utility Disc is located.

3. Click Setup.exe file for utility installation.

4. Follow the instructions on the screen to complete the installation.

5. Once installation is completed, shut down the system and restart in
order for the changes to take effect.

Page:3-8

Prox-1715 USER

′

S MANUAL

Chapter 3 Software Configuration

3-7. USB2.0 SOFTWARE INSTALLATION UTILITY

3-7-1. Installation of Utility for Windows 98SE/ 2000/XP

Intel USB 2.0 Enhanced Host Controller driver can only be used on
Windows 98SE, Windows 2000 and Windows XP on Intel Desktop
boards. It should be installed right after the OS installation, kindly
follow the following steps:

1. Place insert the Utility Disk into Floppy Disk Drive A/B or CD
ROM drive.

2. Under Windows 98SE, 2000, and XP system, go to the directory
where Utility Disc is located.

3. Start the “System” wizard in control panel. (Click
Start/Settings/Control Panel).

4. Select “Hardware” and click “Device Manager ” button.

5. Double Click “USB Root Hub”.

6. Select “Driver”.

7. Click “Install” to install the driver.

8. Follow the instructions on the screen to complete the installation.

9. Click “Finish” after the driver installation is complete.

Prox-1715 USER′S MANUAL

Page:3-9

Chapter 3 Software Configuration

3-8. SCSI AND STORAGE_ATA SOFTWARE INSTALLATION

3-8-1. Installation for SCSI

The SCSI function enhanced in this system is fully compatible with
Windows 95, Windows 98, Windows NT 4.0, and Windows 2000. For
more details please refer to “Readme.txt”. Below, you will find the
content of the SCSI driver :

1. Win 2000 program

2. Win NT4.0 program

3. Win 98 program

4. Win 95 program

To install the SCSI Driver, simply follow the following steps:

1. Place insert the Utility Disk into Floppy Disk Drive A/B or CD
ROM drive.

2. Under Windows system, go to the directory where SCSI driver is
located.

3. Start the “System” wizard in control panel. (Click
Start/Settings/Control Panel).

4. Select “Hardware” and click “Device Manager ” button.

5. Double Click “SCSI Controller”.

6. Select “Driver”.

7. Click “Install” to install the driver.

8. Follow the instructions on the screen to complete the installation.

9. Click “Finish” after the driver installation is complete.

Page:3-10

Prox-1715 USER

′

S MANUAL

3-8-2. Installation for STORAGE_ATA

The STORAGE_ATA function enhanced in this system is fully
compatible with Windows 98, Windows 98SE, Windows ME, Windows
NT 4.0, Windows 2000, and Windows XP. For more details please refer
to “Readme.txt”. Below, you will find the content of the
STORAGE_ATA driver :

To install the STORAGE_ATA Driver, simply follow the following
steps:

1. Place insert the Utility Disk into Floppy Disk Drive A/B or CD
ROM drive.

2. Under Windows system, go to the directory where
STORAGE_ATA driver is located.

3. Click Setup.exe file for driver installation.

4. Follow the instructions on the screen to complete the installation.

5. Once installation is completed, shut down the system and restart in
order for the changes to take effect.

Prox-1715 USER′S MANUAL

Chapter 3 Software Configuration

1. Win 2000 program

2. Win NT4.0 program

3. Win 98 program

4. Win 98SE program

5. Win XP program

6. Win ME program

Page:3-11

Chapter 3 Software Configuration

3-9. WATCHDOG TIMER CONFIGURATION

This board has watchdog timer function for monitoring whether the system
is still work or not after a period of time. The user can select watchdog
timer to system reset or NMI (Non Maskable interrupt) depending on the
jumper set in chapter 2. This is defined at I/O port 443H. When you want to
enable the watchdog timer, please write I/O port 443H, and then the system
will either reset itself or perform the NMI function. Likewise, when you
want to disable the function, write I/O port 441H, the system will run the
command to stop the Watchdog function.

In Prox-1715 watchdog function, you must write your program so when it
writes I/O port address 443 for enable watchdog and write I/O port address
441 for disable watchdog. The timer's intervals have a tolerance of 25%
(but for level 1 and 2, the tolerance is 4%), so you should program an
instruction that will refresh the timer about every second.

The following program shows you how to program the watch timer in your
program.

Watchdog enable program:

MOV AX, 000FH (choose the values you need; start from 0)

MOV DX, 443H

OUT DX, AX

Watchdog disable program:

MOV AX, 000FH (this value can be ignored)
MOV DX, 441H
OUT DX, AX

The Watchdog Timer control table is as follows:

Level Value Time/sec Level Value Time/sec

1 F 0 9 7 64
2 E 8 10 6 72
3 D 16 11 5 80
4 C 24 12 4 88
5 B 32 13 3 96
6 A 40 14 2 104
7 9 48 15 1 112
8 8 56 16 0 120

Page:3-12

Prox-1715 USER

′

S MANUAL

CHAPTER

AWARD
BIOS SETUP

This chapter shows how to set up the Award BIOS.

Section includes:

z Introduction

z Entering Setup

z The Standard CMOS Features

z The Advanced BIOS Features

z The Advanced Chipset Features

z Integrated Peripherals

z Power Management Setup

z PNP/PCI Configuration

z PC Health Status

z Frequency Control

z Load Fail-Safe Defaults

z Load Optimized Defaults

z Password Setting

z Save and Exit Setup

z Exit Without Saving

4

Page: 4-1

Chapter 4 Award BIOS Setup

4-1. INTRODUCTION

This chapter will show you the function of the BIOS in managing the
features of your system. The Prox-1715 Pentium® 4 Full-size CPU Card is
equipped with the BIOS for system chipset from Award Software Inc. This
page briefly explains the function of the BIOS in managing the special
features of your system. The following pages describe how to use the BIOS
for system chipset Setup menu.

Your application programs (such as word processing, spreadsheets, and
games) rely on an operating system such as DOS or OS/2 to manage such
things as keyboard, monitor, disk drives, and memory.

The operating system relies on the BIOS (Basic Input and Output system), a
program stored on a ROM (Read-only Memory) chip, to initialize and
configure your computer's hardware. As the interface between the hardware
and the operating system, the BIOS enables you to make basic changes to
your system's hardware without having to write a new operating system.

The following diagram illustrates the interlocking relationships between the
system hardware, BIOS, operating system, and application program:

Page: 4-2

Prox-1715 USER

′

S MANUAL

Chapter 4 Award BIOS Setup

4-2. ENTERING SETUP

When the system is powered on, the BIOS will enter the Power-On Self
Test (POST) routines and the following message will appear on the lower
screen:

PRESS <DEL> TO ENTER SETUP, ESC TO SKIP MEMORY TEST

As long as this message is present on the screen you may press the <Del>

key (the one that shares the decimal point at the bottom of the number
keypad) to access the Setup program. In a moment, the main menu of the
Award SETUP program will appear on the screen:

Phoenix - AwardBIOS CMOS Setup Utility

►Standard CMOS Features

►Advanced BIOS Features

►Advanced Chipset Features

►Integrated Peripherals

►Power Management Setup

►PnP/PCI Configurations

►PC Health Status

Esc : Quit ↑↓→← : Select Item
F10 : Save & Exit Setup

Time, Date, Hard Disk Type .…

Setup program initial screen

You may use the cursor the up/down keys to highlight the individual menu
items. As you highlight each item, a brief description of the highlighted
selection will appear at the bottom of the screen.

►Frequency Control

Load Fail-Safe Defaults

Load Optimized Defaults

Set Supervisor Password

Set User Password

Save & Exit Setup

Exit Without Saving

Prox-1715 USER′S MANUAL

Page: 4-3

Chapter 4 Award BIOS Setup

4-3. THE STANDARD CMOS FEATURES

Highlight theňSTANDARD CMOS FEATURESʼnand press the <ENTER>
key and the screen will display the following table:

Phoenix - AwardBIOS CMOS Setup Utility

Standard CMOS Features

Date (mm:dd:yy)
Time (hh:mm:ss)

▶ IDE Primary Master
▶ IDE Primary Slave
▶ IDE Secondary Master
▶ IDE Secondary Slave

Drive A
Drive B

Video
Halt On

Base Memory
Extended Memory
Total Memory

Tue, Oct

29 2002

10 : 37 : 33

[MAXTOR 6L040J2]
[Pioneer DVD-ROM ATAP]
[ None]
[ None]

[1.44M, 3.5 in.]
[None]

[EGA/VGA]
[All, But Keyboard]

640K
261120K
262144K

Item Help

Menu Level ►

Change the internal
clock.

↑↓→←: Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5: Previous Values F6: Fail-Safe Defaults F7:Optimized Defaults

CMOS Setup screen

In the above Setup Menu, use the arrow keys to highlight the item and then use
the <PgUp> or <PgDn> keys to select the value you want in each item.

Date:

< Month >, < Date > and <Year >. Ranges for each value are in the CMOS
Setup Screen, and the week-day will skip automatically.

Time:

< Hour >, < Minute >, and < Second >. Use 24 hour clock format, i.e., for PM
numbers, add 12 to the hour. For example: 4: 30 P.M. You should enter the
time as 16:30:00.

Page: 4-4

Prox-1715 USER

′

S MANUAL

IDE Primary Master / Slave:
IDE Secondary Master / Slave:

The options for these items are found in its sub menu. By pressing the
<ENTER> key, you are prompt to enter the sub menu of the detailed options
as shown below:

Phoenix - AwardBIOS CMOS Setup Utility

Chapter 4 Award BIOS Setup

IDE Primary Master

IDE HDD Auto-Detection

IDE Primary Master
Access Mode

Capacity

Cylinder
Head
Precomp
Landing Zone
Sector

↑↓→←: Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5: Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults

[Press Enter]

[Auto]
[Auto]

13022 MB

25232
16
65535
25231
63

Item Help

Menu Level ►►

To auto-detect the
HDD’s size, head…on
this channel

Table 1 – IDE Primary Master sub menu

Descriptions on each item above are as follows:

1. IDE HDD Auto-detection
Press the enter key to auto-detect the HDD on this channel. If detection
is successful, it fills the remaining fields on this menu.

2. IDE Primary Master
There are three available options on this category, namely: None, Auto,
and Manual. By selecting “Manual”, you can set the remaining fields
on this screen, such as -
a. Cylinder – Set the number of cylinders for this hard disk.
b. Head – Set the number of read/write heads.
c. Precomp - ***Warning! Setting a value of 65535 means no HDD.
d. Landing Zone
e. Sector – Set the number of sector per track

Prox-1715 USER′S MANUAL

Page: 4-5

Chapter 4 Award BIOS Setup

3. Access Mode
There are four available options for this item, namely: Normal, LBA,
Large and Auto. Choose the access mode for this hard disk.

4. Capacity
Disk Drive capacity (Approximated). Note that this size is usually
slightly greater than the size of a formatted disk given by a disk­checking program.

DRIVE A AND DRIVE B:

Select the type of floppy disk drive installed in your system. The available
options are 360KB 5.25in, 1.2KB 5.25in, 720KB 3.5in, 1.44MB 3.5in,

2.88MB 3.5in and None.

VIDEO:

This category selects the type of video adapter used for the primary system
monitor. Although secondary monitors are supported, you do not have to
select the type in Setup. Available Options are as follows:

EGA/VGA Enhanced Graphics Adapter/Video Graphics Array.

For EGA, VGA, SEGA, SVGA or PGA monitor

adapters.
CGA 40 Color Graphics Adapter, power up in 40 column mode.
CGA 80 Color Graphics Adapter, power up in 80 column mode.
MONO Monochrome adapter, includes high resolution

monochrome adapters.

HALT ON:

This category allows user to choose whether the computer will stop if an error
is detected during power up. Available options are “All errors”, “No errors”,
“All, But keyboard”, “All, But Diskette”, and “All But Disk/Key”.

BASE MEMORY:

Displays the amount of conventional memory detected during boot up.

EXTENDED MEMORY:

Displays the amount of extended memory detected during boot up.

TOTAL MEMORY:

Displays the total memory available in the system.

Page: 4-6

Prox-1715 USER

′

S MANUAL

HARD DISK ATTRIBUTES:

Type Cylinders Heads V-P comp LZone Sect Capacity

1 306 4 128 305 17 10
2 615 4 300 615 17 20
3 615 6 300 615 17 30
4 940 8 512 940 17 62
5 940 6 512 940 17 46
6 615 4 65535 615 17 20
7 642 8 256 511 17 30
8 733 5 65535 733 17 30

9 900 15 65535 901 17 112
10 820 3 65535 820 17 20
11 855 5 65535 855 17 35
12 855 7 65535 855 17 49
13 306 8 128 319 17 20
14 733 7 65535 733 17 42
15 000 0 0000 000 00 00
16 612 4 0000 663 17 20
17 977 5 300 977 17 40
18 977 7 65535 977 17 56
19 1024 7 512 1023 17 59
20 733 5 300 732 17 30
21 733 7 300 732 17 42
22 733 5 300 733 17 30
23 306 4 0000 336 17 10
24 977 5 65535 976 17 40
25 1024 9 65535 1023 17 76
26 1224 7 65535 1223 17 71
27 1224 11 65535 1223 17 111
28 1224 15 65535 1223 17 152
29 1024 8 65535 1023 17 68
30 1024 11 65535 1023 17 93
31 918 11 65535 1023 17 83
32 925 9 65535 926 17 69
33 1024 10 65535 1023 17 85
34 1024 12 65535 1023 17 102
35 1024 13 65535 1023 17 110
36 1024 14 65535 1023 17 119
37 1024 2 65535 1023 17 17
38 1024 16 65535 1023 17 136
39 918 15 65535 1023 17 114
40 820 6 65535 820 17 40
41 1024 5 65535 1023 17 42
42 1024 5 65535 1023 26 65
43 809 6 65535 852 17 40
44 809 6 65535 852 26 61
45 776 8 65335 775 33 100

47 AUTO

Chapter 4 Award BIOS Setup

Award Hard Disk Type Table

Prox-1715 USER′S MANUAL

Page: 4-7

Chapter 4 Award BIOS Setup

4-4. THE ADVANCED BIOS FEATURES

Choose theňADVANCED BIOS FEATURESʼnin the main menu, the screen
shown as below.

Phoenix - AwardBIOS CMOS Setup Utility

Advanced BIOS Features

Virus Warning

CPU L1 & L2 Cache

Quick Power On Self Test

First Boot Device

Second Boot Device

Third Boot Device

Boot Other Device

Swap Floppy Drive

Boot Up Floppy Seek

Boot Up NumLock Status

Gate A20 Option

Typematic Rate Setting

x Typematic Rate (Chars/Sec)
x Typematic Delay (Msec)

Security Option

OS Select For DRAM > 64MB

HDD S.M.A.R.T Capability

Small Logo (EPA) Show

↑↓→←: Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5: Previous Values F6: Fail-Safe Defaults F7:Optimized Defaults

The “BIOS FEATURES SETUP” allow you to configure your system for
basic operation. The user can select the system’s default speed, boot-up
sequence, keyboard operation, shadowing and security.

A brief introduction of each setting is given below.

VIRUS WARNING :

This item allows you to choose the Virus Warning feature for IDE Hard Disk
boot sector protection. If this function is enabled and someone attempt to
write data into this area, BIOS will show a warning message on screen and
alarm beep.

Page: 4-8

[Disabled]
[Enabled]
[Enabled]
[Floppy]
[HDD-0]
[LS120]
[Enabled]
[Disabled]
[Disabled]
[On]
[Fast]
[Disabled]
6
250
[Setup]
[Non-OS2]
[Disabled]
[Disabled]

BIOS Features Setup Screen

Prox-1715 USER

Item Help

Menu Level ►

′

S MANUAL

CPU L1 & L2 CACHE :

This item allows you to enable L1 & L2 cache.

QUICK POWER ON SELF-TEST:

This item allows you to speed up Power On Self Test (POST) after power-up
the computer. When enabled, the BIOS will shorten or skip some check items
during POST.

FIRST/SECOND/THIRD/OTHER BOOT DEVICE:

The BIOS attempt to load the operating system from the devices in the
sequence selected in these items.

SWAP FLOOPY DRIVE:

This field is effective only in systems with two floppy drives. Selecting
Enabled assigns physical drive B to logical drive A, and physical drive A to
logical drive B.

BOOT UP FLOPPY SEEK:

You may enable / disable this item to define whether the system will look for
a floppy disk drive to boot at power-on, or proceed directly to the hard disk
drive.

BOOT UP NUMLOCK STATUS:

Select power on state for NumLock.

GATE A20 OPTION:

This entry allows you to select how the gate A20 is handled. When Normal
was set, a pin in the keyboard controller controls Gate A20. And when Fast
was set, the chipset controls Gate A20.

TYPEMATIC RATE SETTING:

Enable this item if you wish to be able to configure the characteristics of
your keyboard. Typematic refers to the way in which characters are entered
repeatedly if a key is held down. For example, if you press and hold down
the "A" key, the letter "a" will repeatedly appear on your screen on your
screen until you release the key. When enabled, the typematic rate and
typematic delay can be selected.

Chapter 4 Award BIOS Setup

Prox-1715 USER′S MANUAL

Page: 4-9

Chapter 4 Award BIOS Setup

TYPEMATIC RATE (CHARS/SEC):

This item sets the number of times a second to repeat a key stroke when you
hold the key down.

TYPEMATIC DELAY (MSEC):

The item sets the delay time after the key is held down before it begins to
repeat the keystroke.

SECURITY OPTION:

This category allows you to limit access to the system and Setup, or just to
Setup.

System The system will not boot and access to Setup will be

denied if the correct password is not entered at the
prompt.

Setup The system will boot, but access to Setup will be

denied if the correct password is not entered at the
prompt.

 To disable security, select PASSWORD SETTING at Main Menu and

then you will be asked to enter password. Do not type anything and just
press <Enter>, it will disable security. Once the security is disabled, the
system will boot and you can enter Setup freely.

OS SELECT FOR DRAM >64MB :

Select the operating system that is running with greater than 64MB or RAM
on the system. You may choose OS2 or Non-OS2.

Page: 4-10

Prox-1715 USER

′

S MANUAL

Chapter 4 Award BIOS Setup

4-5. ADVANCED CHIPSET FEATURES

Choose theňADVANCED CHIPSET FEATURESʼnfrom the main menu,

the screen shown as below.

Phoenix - AwardBIOS CMOS Setup Utility

Advanced Chipset Features

DRAM Timing Selectable

x

CAS Latency Time

x Active to Precharge Delay
x DRAM RAS# to CAS# Delay
x DRAM RAS# Precharge
DRAM Data Integrity Mode

Memory Frequency For
DRAM Read Thermal Mgmt
System BIOS Cacheable
Video BIOS Cacheable
Memory Hole At 15M-16M
Delayed Transaction
AGP Aperture Size (MB)
IO Channel Check NMI

[By SPD]

2
6
3

3
[Non-ECC]
[Auto]
[Disabled]
[Enabled]
[Disabled]
[Disabled]
[Enabled]
[64]
[Disabled]

Item Help

Menu Level ►

↑↓→←: Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5: Previous Values F6: Fail-Safe Defaults F7:Optimized Defaults

Chipset Features Setup Screen

This parameter allows you to configure the system based on the specific
features of the installed chipset. The chipset manages bus speed and
access to system memory resources, such as DRAM and the external cache.

It also coordinates communications between conventional ISA bus and the
PCI bus. It must be stated that these items should never need to be altered.
The default settings have been chosen because they provide the best opera­ting conditions for the system. The only time you might consider making
any changes would be if you discovered that data was being lost while
using your system.

Prox-1715 USER′S MANUAL

Page: 4-11

Chapter 4 Award BIOS Setup

DRAM TIMING BY SELECTABLE:

This allows you to select the DRAM timing.

CAS LATENCY TIME:

When synchronous DRAM is installed, the number of clock cycles of CAS
latency depends on the DRAM timing.

ACTIVE TO PRECHARGE DELAY:

This item controls the number of DRAM clocks for TRAS.

DRAM RAS# TO CAS# DELAY:

This field let’s you insert a timing delay between the CAS and RAS strobe
signals, used when DRAM is written to, read from, or refreshed. Fast gives
faster performance; and Slow gives more stable performance. This field
applies only when synchronous DRAM is installed in the system.

DRAM RAS# PRECHARGE:

If an insufficient number of cycles is allowed for the RAS to accumulate its
charge before DRAM refresh, the refresh may be incomplete and the DRAM
may fail to retain data. Fast gives faster performance; and Slow gives more
stable performance. This field applies only when synchronous DRAM is
installed in the system.

DRAM DATA INTEGRITY MODE:

This item allows you to enable/disable the DRAM ECC function which will
recover the single bit errors when user plug-in ECC DRAM.

SYSTEM BIOS CACHEABLE:

Selecting Enabled allows caching of the system BIOS ROM at F0000h­FFFFFh, resulting in better system performance. However, if any program
writes to this memory area, a system error may result.

VIDEO BIOS CACHEABLE:

Select Enabled allows caching of the video BIOS, resulting in better system
performance. However, if any program writes to this memory area, a system
error may result.

Page: 4-12

Prox-1715 USER

′

S MANUAL

MEMORY HOLE AT 15M-16M:

You can reserve this area of system memory for ISA adapter ROM. When
this area is reserved, it cannot be cached. The user information of
peripherals that need to use this area of system memory usually discusses their
memory requirements.

DELAYED TRANSACTION:

The chipset has an embedded 32-bit posted write buffer to support delay
transactions cycles. Select Enabled to support compliance with PCI
specification version 2.1.

AGP APERTURE SIZE:

This field determines the effective size of the Graphic Aperture used for a
particular GMCH configuration. It can be updated by the GMCH-specific
BIOS configuration sequence before the PCI standard bus enumeration
sequence takes place. If it is not updated then a default value will select an
aperture of maximum size.

IO CHANNEL CHECK NMI:

This field allows you to enable or disable IO channel check NMI. Before
selecting this function, the user should check first that NMI function is
enabled as described in chapter 2 (Reset/NMI/Clear Watchdog Selection).

Chapter 4 Award BIOS Setup

Prox-1715 USER′S MANUAL

Page: 4-13

Chapter 4 Award BIOS Setup

4-6. INTEGRATED PERIPHERALS

ChooseňINTEGRATED PERIPHERALSʼnfrom the main setup menu, a
display will be shown on screen as below:

Phoenix - AwardBIOS CMOS Setup Utility

Integrated Peripherals

On-Chip Primary PCI IDE
IDE Primary Master
IDE Primary Slave PIO
IDE Primary Master
IDE Primary Slave
On-Chip Secondary PCI IDE
IDE Secondary Master PIO
IDE Secondary Slave PIO
IDE Secondary Master
IDE Secondary Slave UDMA
USB Controller
USB 2.0 Controller
USB Keyboard Support
USB Mouse Support
AC97 Audio
Init Display First
BIOS Flash Function
IDE HDD Block Mode

POWER ON Function
x KB Power ON Password
x Hot Key Power ON

Onboard FDC Controller

Onboard Serial Port 1

Onboard Serial Port 2

UART Mode Select
x RxD, TxD Active
x IR Transmission Delay
x UR2 Duplex Mode
x Use IR Pins

Onboard Parallel Port

Parallel Port Mode
x EPP Mode Select
x ECP Mode Use DMA

PWRON After PWR-Fail

↑↓→←: Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5: Previous Values F6: Fail-Safe Defaults F7:Optimized Defaults

By moving the cursor to the desired selection and by pressing the <F1> key,
the all options for the desired selection will be displayed for choice.

Page: 4-14

PIO

UDMA

UDMA

UDMA

Integrated Peripherals Setup Screen

[Enabled]
[Auto]
[Auto]
[Auto]
[Auto]
[Enabled]
[Auto]
[Auto]
[Auto]
[Auto]
[Enabled]
[Enabled]
[Disabled]
[Disabled]
[Auto]
[Onboard]
[Enabled]
[Enabled]
[BUTTON ONLY]
Enter
Ctrl-F1
[Enabled]
[3F8/IRQ4]
[2F8/IRQ3]
[Normal]
Hi, Lo
Enabled
Half
IR-Rx2Tx2
[378/IRQ7]
[SPP]
EPP1.7
3
[Off]

Item Help

Menu Level

Prox-1715 USER

►

′

S MANUAL

ON-CHIP PRIMARY PCI IDE:
ON-CHIP SECONDARY PCI IDE:

The chipset contains a PCI IDE interface with support for two IDE
channels. Select Enabled to activate the primary or secondary IDE
interface. Select Disabled to deactivate this interface.

IDE PRIMARY MASTER/SLAVE PIO:
IDE SECONDARY MASTER/SLAVE PIO:

The four IDE PIO fields allow you to set a PIO mode (0-4) for each of the
four IDE devices that the onboard IDE interface supports. Modes 0 through
4 provide successively increased performance. In Auto mode, the system
automatically determines the best mode for each device.

IDE PRIMARY MASTER/SLAVE UDMA:
IDE SECONDARY MASTER/SLAVE UDMA:

Ultra DMA/33 implementation is possible only if your IDE hard drive
supports it and the operating environment includes a DMA driver (Windows
95 OSR2 or a third-party IDE bus master driver). If you hard drive and your
system software both support Ultra DMA/33, select Auto to enable BIOS
support.

USB CONTROLLER:

Select enabled if the system contains a Universal Serial Bus (USB) controller
and you have a USB peripherals.

USB KEYBOARD SUPPORT:

Select Enabled if you have a USB Keyboard.

USB MOUSE SUPPORT:

Select enabled if the system contains a Universal Serial Bus (USB) controller
and you have a USB Mouse.

INIT DISPLAY FIRST:

This item allows you to decide to active whether PCI Slot or on-chip VGA
first.

BIOS FLASH FUNCTION:

This item allows you to enable the BIOS Flash function.

Chapter 4 Award BIOS Setup

Prox-1715 USER′S MANUAL

Page: 4-15

Chapter 4 Award BIOS Setup

IDE HDD BLOCK MODE:

Block mode is also called block transfer, multiple commands, or multiple
sector read/write. If your IDE hard drive supports block mode (most new
drives do), select Enabled for automatic detection of the optimal number of
block read/writes per sector the drive can support.

ONBOARD FDC CONTROLLER:

Select Enabled if the system has a floppy disk controller (FDC) installed on
the system board and you wish to use it. If you install and-in FDC or the
system has no floppy drive, select Disabled.

ONBOARD SERIAL PORT 1:
ONBOARD SERIAL PORT 2:

Select an address and corresponding interrupt for the first and second serial
ports.

UART MODE SELECT:

This item allows you to select UART mode.

RxD, TxD ACTIVE:

This item allows you to determine the active of RxD, TxD.

IR TRANSMISSION DELAY:

This item allows you to enable/disable IR transmission delay.

UR2 DUPLEX MODE:

This item allows you to select the IR half/full duplex function.

USE IR PINS:

This item allows you to select IR transmission routes, one is RxD2m, TxD2
(COM Port) and the other is IR-Rx2Tx2.

ONBOARD PARALLEL PORT:

This item allows you to determine access onboard parallel port controller with
which I/O address.

PARALLEL PORT MODE:

Select an operating mode for the onboard parallel (printer) port. Select
Normal, Compatible, or SPP unless you are certain your hardware and
software both support one of the other available modes.

Page: 4-16

Prox-1715 USER

′

S MANUAL

EPP MODE SELECT:

Select EPP port type 1.7 or 1.9.

ECP MODE USE DMA:

Select a DMA channel for the parallel port for use during ECP mode.

PWRON AFTER PWR-FAIL:

This item allows you to select if you want to power on the system after
power failure.

Chapter 4 Award BIOS Setup

Prox-1715 USER′S MANUAL

Page: 4-17

Chapter 4 Award BIOS Setup

4-7. POWER MANAGEMENT SETUP

ChooseňPOWER MANAGEMENT SETUPʼnoption on the main menu, a
display will be shown on screen as below :

Phoenix - AwardBIOS CMOS Setup Utility

Power Management Setup

ACPI Function

Power Management

MODEM Use IRQ

Suspend Mode

Soft-Off by PWR-BTTN

Wake-Up by PCI card

Power On by Ring

Resume by Alarm
x Date (of Month) Alarm
x Time (hh:mm:ss) Alarm

** Reload Global Timer Events **
Primary IDE 0
Primary IDE 1
Secondary IDE 0
Secondary IDE 1
FDD, COM, LPT Port

↑↓→←: Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

[Enabled]
[User Define]
[3]
[Disabled]
[Instant-Off]
[Enabled]
[Enabled]
[Disabled]
0
0 : 0 : 0

[Disabled]
[Disabled]
[Disabled]
[Disabled]
[Disabled]

Item Help

Menu Level ►

F5: Previous Values F6: Fail-Safe Defaults F7:Optimized Defaults

Power Management Setup Screen

The “Power Management Setup” allows the user to configure the system to
the most effectively save energy while operating in a manner consistent with
your own style of computer use.

ACPI SUSPEND TYPE:

This item allows the user to set the ACPI suspend type to be used.

POWER MANAGEMENT:

This item allows you to select the Power Management mode.

Page: 4-18

Prox-1715 USER

′

S MANUAL

MODEM USE IRQ:

This item enable you to name the interrupt request (IRQ) line assigned to
the modem (if any) on your system. Activity of the selected IRQ always
awakens the system.

SUSPEND MODE:

When enabled and after the set time of system inactivity, all devices except
the CPU will be shut off.

SOFT-OFF BY PWR-BTTN:

Pressing the power button for more than 4 seconds forces the system to
enter the Soft-Off state when the system has “hung”. The choices are
Delay 4 Sec and Instant-Off.

WAKE-UP BY PCI CARD:

An input signal from PME on the PCI card awakens the system from a soft
off state.

POWER ON BY RING:

This category enables or disables the powering up of the system when the
modem receives a call while the computer is in Soft-Off state.

RESUME BY ALARM:

When Enabled, your can set the date and time at which the RTC (real-time
clock) alarm awakens the system from Suspend mode.

PM EVENTS:

PM events are I/O events whose occurrence can prevent the system from
entering a power saving mode or can awaken the system from such a mode.
In effect, the system remains alert for anything, which occurs to a device
which is configured as Enabled, even when the system is in a power down
mode. (1) Primary IDE 0 (2) Primary IDE 1 (3) Secondary IDE 0 (4)
Secondary IDE 1 (5) FDD, COM, LPT Port

Chapter 4 Award BIOS Setup

Prox-1715 USER′S MANUAL

Page: 4-19

Chapter 4 Award BIOS Setup

4-8. PNP/PCI CONFIGURATION

Choose ňPNP/PCI CONFIGURATIONʼn from the main menu, a display
will be shown on screen as below:

Phoenix - AwardBIOS CMOS Setup Utility

PnP/PCI Configurations

PNP OS Installed

Reset Configuration Data

Resources Controlled By
x IRQ Resources
x DMA Resources

PCI/VGA Palette Snoop

[No]
[Disabled]

[Auto (ESCD)]

Press Enter
Press Enter

[Disabled]

Item Help

Menu Level ►

Select Yes if you are
using a Plug and Play
capable operating
system Select No if
you need the BIOS to
configure non-boot
devices

↑↓→←: Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5: Previous Values F6: Fail-Safe Defaults F7:Optimized Defaults

PNP/PCI Configuration Setup Screen

The PNP/PCI Configuration Setup describes how to configure PCI bus system.
PCI, also known as Personal Computer Interconnect, is a system, which
allows I/O devices to operate at speeds nearing the speed of the CPU itself
uses when communicating with its own special components.

This section covers technical items, which is strongly recommended for
experienced users only.

PNP OS INSTALLED:

This item allows you to determine install PnP OS or not.

Page: 4-20

Prox-1715 USER

′

S MANUAL

RESET CONFIGURATION DATA:

Normally, you leave this field Disabled. Select Enabled to reset Extended
System Configuration Data (ESCD) when you exit Setup if you have
installed a new add-on and the system configuration has caused such a
serious conflict that the operating system cannot boot.

RESOURCE CONTROLLED BY:

The Award Plug and Play Bios can automatically configure all of the booth
and Plug and Play-compatible devices. However, this capability means
absolutely nothing unless you are using a Plug and Play operating system
such as Windows 95. By choosing “manual”, you are allowed to
configure the IRQ Resources and DMA Resources.

IRQ RESOURCES:

You may assign each system interrupt a type, depending on the type of
device using the interrupt.

DMA RESOURCES:

When resources are controlled manually, assign each system DMA channel
a type, depending on the type of device using the DM channel.

PCI/VGA PALETTE SNOOP:

Leave this field at disabled.

Chapter 4 Award BIOS Setup

Prox-1715 USER′S MANUAL

Page: 4-21

Chapter 4 Award BIOS Setup

4-9. PC HEALTH STATUS

Choose ňPC HEALTH STATUSʼn from the main menu, a display will
be shown on screen as below:

Phoenix - AwardBIOS CMOS Setup Utility

PC Health Status

Current CPU Temperature

Current CPU Fan Speed

Vcore

3.3

V

+ 5 V

+12

V

-12

V

- 5

V

VBAT (V)

5VSB (V)

Shutdown Temperature

↑↓→←: Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5: Previous Values F6: Fail-Safe Defaults F7:Optimized Defaults

PC Health Status Setup Screen

The PC Health Status Setup allows you to select whether to choose between
monitoring or to ignore the hardware monitoring function of your system.

CURRENT WARNING TEMPERATURE:

Select the combination of lower and upper limits for the CPU temperature.
If the CPU temperature extends beyond either limit, any warning
mechanism programmed into your system will be activated.

CURRENT CPU TEMPERATURE:

This item shows you the current CPU temperature.

CURRENT CPU FAN SPEED:

This item shows you the current CPUFAN speed.

VCORE:

This item shows you the current system voltage.

Page: 4-22

[Disabled]
50ƨ/122Ʃ
4218 RPM

1.69V

3.23V

5.05V

11.43V

-11.45V

- 4.99V

3.21V

4.87V

[Disabled]

Item Help Current Warning Temperature

Menu Level ►

Prox-1715 USER

′

S MANUAL

3.3V / +5V / +12V / -12V / -5V:

Show you the voltage of 3.3V/+5V/+12V/-12V/-5V.

SHUTDOWN TEMPERATURE:

This item allows you to set up the CPU shutdown Temperature. This
function is only effective under Windows 98 ACPI mode.

4-10. FREQUENCY CONTROL

Choose ňFREQUENCY CONTROLʼn from the main menu, a display
will be shown on screen as below:

Phoenix - AwardBIOS CMOS Setup Utility

Frequency Control

Auto Detect PCI Clk

Spread Spectrum

↑↓→←: Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5: Previous Values F6: Fail-Safe Defaults F7:Optimized Defaults

Frequency Control Setup Screen

This setup menu allows you to specify your settings for frequency control.

AUTO DETECT PCI CLK:

This item allows you to enable or disable auto detect PCI Clock.

[Enabled]
[Disabled]

Chapter 4 Award BIOS Setup

Item Help

Menu Level ►

Prox-1715 USER′S MANUAL

Page: 4-23

Chapter 4 Award BIOS Setup

SPREAD SPECTRUM:

When the system clock generator pulses, the extreme values of the pulse
generate excess EMI. Enabling pulse spectrum spread modulation
changes the extreme values from spikes to flat curves, thus reducing EMI.
This benefit may in some cases be outweighed by problems with timing­critical devices such as a clock-sensitive SCSI device.

4-11. LOAD FAIL-SAFE DEFAULTS

By pressing the <ENTER> key on this item, you get a confirmation dialog
box with a message similar to the following:

Load Fail-Safe Defaults ( Y/N ) ? N

To use the BIOS default values, change the prompt to "Y" and press the
<Enter > key. CMOS is loaded automatically when you power up the
system.

4-12. LOAD OPTIMIZED DEFAULTS

When you press <Enter> on this category, you get a confirmation dialog
box with a message similar to the following:

Pressing "Y" loads the default values that are factory setting for optimal
performance system operations.

Page: 4-24

Load Optimized Defaults ( Y/N ) ? N

Prox-1715 USER

′

S MANUAL

4-13. PASSWORD SETTING

User is allowed to set either supervisor or user password, or both of them.
The difference is that the supervisor password can enter and change the
options of the setup menus while the user password can enter only but do not
have the authority to change the options of the setup menus.

TO SET A PASSWORD

When you select this function, the following message will appear at the
center of the screen to assist you in creating a password.

Enter Password:

Type the password up to eight characters in length, and press < Enter >.
The password typed now will clear any previously entered password from
CMOS memory. You will be asked to confirm the password. Type the
password again and press the < Enter > key. You may also press < Esc >
to abort the selection and not enter a password.

 User should bear in mind that when a password is set, you will be

asked to enter the password everything you enter CMOS setup Menu.

TO DISABLE THE PASSWORD

To disable the password, select this function (do not enter any key when
you are prompt to enter a password), and press the <Enter> key and a
message will appear at the center of the screen:

Chapter 4 Award BIOS Setup

PASSWORD DISABLED!!!

Press any key to continue...

Press the < Enter > key again and the password will be disabled. Once the
password is disabled, you can enter Setup freely.

Prox-1715 USER′S MANUAL

Page: 4-25

Chapter 4 Award BIOS Setup

4-14. SAVE & EXIT SETUP

After you have completed adjusting all the settings as required, you must
remember to save these setting into the CMOS RAM. To save the settings,
select “SAVE & EXIT SETUP” and press <Enter>, a display will be shown
as follows:

Phoenix - AwardBIOS CMOS Setup Utility

►Standard CMOS Features

►Advanced BIOS Features

►Advanced Chipset Features

►Integrated Peripherals

►Power Management

►PnP/PCI Configura

►PC Health Status

Esc : Quit ↑↓→← : Select Item
F10 : Save & Exit Setup

When you confirm that you wish to save the settings, your system will be
automatically restarted and the changes you have made will be implemented.
You may always call up the setup program at any time to adjust any of the
individual items by pressing the <Del> key during boot up.

Save to CMOS and EXIT Y/N)? Y

►Frequency Control

Load Fail-Safe Defaults

Load Optimized Defaults

Set Supervisor Password

word

etup

Saving

Save Data to CMOS

Page: 4-26

Prox-1715 USER

′

S MANUAL

4-15. EXIT WITHOUT SAVING

If you wish to cancel any changes you have made, you may select the
“EXIT WITHOUT SAVING” and the original setting stored in the CMOS
will be retained. The screen will be shown as below:

Phoenix - AwardBIOS CMOS Setup Utility

►Standard CMOS Features

►Advanced BIOS Features

►Advanced Chipset Features

►Integrated Peripherals

►Power Management

►PnP/PCI Configura

►PC Health Status

Esc : Quit ↑↓→← : Select Item
F10 : Save & Exit Setup

Quit Without Saving (Y/N)? N

Abandon all Datas

Chapter 4 Award BIOS Setup

►Frequency Control

Load Fail-Safe Defaults

Load Optimized Defaults

Set Supervisor Password

word

etup

Saving

Prox-1715 USER′S MANUAL

Page: 4-27

Chapter 4 Award BIOS Setup

Page: 4-28

Prox-1715 USER

′

S MANUAL

APPENDIX

EXPANSION BUS

This appendix indicates the pin assignments.

Section includes:

z ISA BUS Pin Assignment

z PCI BUS Pin Assignment

A

Page: A-1

Appendix A Expansion Bus

A

ISA BUS PIN ASSIGNMENT

There are two edge connectors (called “gold fingers“) on this CPU Card, on the
right hand is the connector of ISA Bus, followed up by PCI BUS connector. The
ISA-bus connector is divided into two sets: one consists of 62 pins; the other
consists of 36 pins. The pin assignments are as follows :

D18

B A D C

PIN ASSIGNMENT PIN ASSIGNMENT PIN ASSIGNMENT PIN ASSIGNMENT

B1 GND A1 -I/O CH CHK D1 -MEMCS16 C1 SBHE
B2 RESET A2 SD07 D2 -I/OCS16 C2 LA23
B3 +5V A3 SD06 D3 IRQ10 C3 LA22
B4 IRQ9 A4 SD05 D4 IRQ11 C4 LA21
B5 NC A5 SD04 D5 IRQ12 C5 LA20
B6 NC A6 SD03 D6 IRQ15 C6 LA19
B7 -12V A7 SD02 D7 IRQ14 C7 LA18
B8 OWS A8 SD01 D8 -DACK0 C8 LA17
B9 +12V A9 SD00 D9 DRQ0 C9 -MEMR
B10 GND A10 -I/O CH RDY D10 -DACK5 C10 -MEMW
B11 -SMEMW A11 AEN D11 DRQ5 C11 SD08
B12 -SMEMR A12 SA19 D12 -DACK6 C12 SD09
B13 -IOW A13 SA18 D13 DRQ6 C13 SD10
B14 -IOR A14 SA17 D14 -DACK7 C14 SD11
B15 -DACK3 A15 SA16 D15 DRQ7 C15 SD12
B16 -DRQ3 A16 SA15 D16 +5V C16 SD13
B17 -DACK1 A17 SA14 D17 -MASTER C17 SD14
B18 -DRQ1 A18 SA13 D18 GND C18 SD15
B19 -REFRESH A19 SA12
B20 BCLK A20 SA11
B21 IRQ7 A21 SA10
B22 NC A22 SA09
B23 IRQ5 A23 SA08
B24 IRQ4 A24 SA07
B25 IRQ3 A25 SA06
B26 NC A26 SA05
B27 T/C A27 SA04
B28 BALE A28 SA03
B29 +5V A29 SA02
B30 OSC A30 SA01
B31 GND A31 SA00

D1

B31

31

C1C18

COMPONENT SIDE

B1

A1

Page: A-2

Prox-1715 USER

′

S MANUAL

Appendix A Expansion Bus

PCI BUS PIN ASSIGNMENT

Like ISA-BUS connector, the PCI-BUS edge connector is also divided into two
sets: one consists of 98-pin; the other consists of 22-pin. The standard of PICMG
32-bit PCI-ISA connector contains 218 pins in total.
The pin assignments are as follows :

F52F62

F49

F1

E62

E52

E49

F E F E

PIN ASSIGNMENT PIN ASSIGNMENT PIN ASSIGNMENT PIN ASSIGNMENT

F1 -12V E1 TRST# F31 NC E31 AD18
F2 TCK E2 +12V F32 AD17 E32 AD16
F3 GND E3 TMS F33 C/BE2# E33 NC
F4 TDO E4 TDI F34 GND E34 FRAME#
F5 +5V E5 +5V F35 IRDY# E35 GND
F6 +5V E6 INTA# F36 NC E36 TRDY#
F7 INTB# E7 INTC# F37 DEVSEL# E37 GND
F8 INTD# E8 +5V F38 GND E38 STOP#
F9 REQ3# E9 CLKC F39 LOCK# E39 NC
F10 REQ1# E10 +5V(I/O) F40 PERR# E40 SDONE
F11 GNT3# E11 CLKD F41 NC E41 SB0#
F12 GND E12 GND F42 SERR# E42 GND
F13 GND E13 GND F43 NC E43 PAR
F14 CLKA E14 GNT1# F44 C/BE1# E44 AD15
F15 GND E15 RST# F45 AD14 E45 NC
F16 CLKB E16 +5V(I/O) F46 GND E46 AD13
F17 GND E17 GNT0# F47 AD12 E47 AD11
F18 REQ0# E18 GND F48 AD10 E48 GND
F19 +5V(I/O) E19 REQ2# F49 GND E49 AD09
F20 AD31 E20 AD30 F52 AD08 E52 C/BE0#
F21 AD29 E21 NC F53 AD07 E53 NC
F22 GND E22 AD28 F54 NC E54 AD06
F23 AD27 E23 AD26 F55 AD05 E55 AD04
F24 AD25 E24 GND F56 AD03 E56 GND
F25 NC E25 AD24 F57 GND E57 AD02
F26 C/BE3# E26 GNT2# F58 AD01 E58 AD00
F27 AD23 E27 NC F59 +5V(I/O) E59 +5V(I/O)
F28 GND E28 AD22 F60 ACK64# E60 REQ64#
F29 AD21 E29 AD20 F61 +5V E61 +5V
F30 AD19 E30 GND F62 +5V E62 +5V

E1

Prox-1715 USER′S MANUAL

Page: A-3

Appendix A Expansion Bus

Page: A-4

Prox-1715 USER

′

S MANUAL

TECHNICAL
SUMMARY

This section introduce you the maps concisely.

Section includes:

z Block Diagram

z Interrupt Map

z RTC & CMOS RAM Map

z Timer & DMA Channels Map

z I / O & Memory Map

APPENDIX

B

Page: B-1

A

Appendix B Technical Summary

BLOCK DIAGRAM

A
D
D
R

AGTL+ BUS

C

D

N

A
T

T

A

L

A
D
D
R

C

D

N

A
T

T

A

L

CRT

LCD

USB 2/2

FWH

Floppy

KB/MS

IrDA

ATI M6 D
VGA CHIP
4X AGP

MCH

BROOKDALE

ICH4

LPC SIO
W83627HF

COM 1/2PRN1

PCI BUS

2 DDR DIMM

MODULES

C97' Codec

LAN 82562

RJ-45 Jack

BRIDGE

IT8888TF

SSD

(DOC)

ISA BUS

WDG

Page: B-2

Prox-1715 USER

′

S MANUAL

INTERRUPT MAP

IRQ ASSIGNMENT

0 System TIMER
1 Keyboard
2 Cascade
3 Serial port 2
4 Serial port 1
5 Available
6 Floppy
7 Parallel port 1
8 RTC clock

9 Available
10 Available
11 Available
12 PS/2 Mouse
13 Math coprocessor
14 IDE1
15 IDE2

Appendix B Technical Summary

Prox-1715 USER′S MANUAL

Page: B-3

Appendix B Technical Summary

RTC & CMOS RAM MAP

CODE ASSIGNMENT

00 Seconds
01 Second alarm
02 Minutes
03 Minutes alarm
04 Hours
05 Hours alarm
06 Day of week
07 Day of month
08 Month

09 Year
0A Status register A
0B Status register B
0C Status register C
0D Status register D
0E Diagnostic status byte

0F Shutdown byte

10 Floppy Disk drive type byte

11 Reserve

12 Hard Disk type byte

13 Reserve

14 Equipment byte

15 Base memory low byte

16 Base memory high byte

17 Extension memory low byte

18 Extension memory high byte

30 Reserved for extension memory low byte

31 Reserved for extension memory high byte

32 Date Century byte

33 Information Flag

34-3F Reserve

40-7f Reserved for Chipset Setting Data

Page: B-4

Prox-1715 USER

′

S MANUAL

TIMER & DMA CHANNELS MAP

Timer Channel Map

Timer Channel Assignment

0 System timer interrupt
1 DRAM Refresh request
2 Speaker tone generator

DMA Channel Map

DMA Channel Assignment

0 Available
1 Available
2 Floppy
3 Available
4 Cascade
5 Available
6 Available
7 Available

:

:

Appendix B Technical Summary

Prox-1715 USER′S MANUAL

Page: B-5

Appendix B Technical Summary

I/O & MEMORY MAP

Memory Map :

MEMORY MAP ASSIGNMENT

0000000-009FFFF System memory used by DOS and

application

00A0000-00BFFFF Display buffer memory for VGA/ EGA /

CGA / MONOCHROME adapter

00C0000-00DFFFF Reserved for I/O device BIOS ROM or

RAM buffer.
00E0000-00EFFFF Reserved for PCI device ROM
00F0000-00FFFFF System BIOS ROM
0100000-FFFFFFF System extension memory

I/O Map :

I/O MAP ASSIGNMENT

000-01F DMA controller (Master)
020-021 Interrupt controller (Master)
022-023 Chipset controller registers I/O ports.
040-05F Timer control regsiters.
060-06F Keyboard interface controller (8042)
070-07F RTC ports & CMOS I/O ports

080-09F DMA register
0A0-0BF Interrupt controller (Slave)
0C0-0DF DMA controller (Slave)

0F0-0FF Math coprocessor

1F0-1F8 Hard Disk controller

278-27F Parallel port-2
2B0-2DF Graphics adapter controller

2F8-2FF Serial port-2

360-36F Net work ports

378-37F Parallel port-1
3B0-3BF Monochrome & Printer adapter
3C0-3CF EGA adapter
3D0-3DF CGA adapter

3F0-3F7 Floppy disk controller

3F8-3FF Serial port-1

Page: B-6

Prox-1715 USER

′

S MANUAL

TROUBLE
SHOOTING

This section outlines the errors may occur when you operate the
system. It also gives you the suggestions on solving the problems.

Section includes:

z Trouble Shooting for Error Messages

z Trouble Shooting for POST Code

APPENDIX

C

Page: C-1

Appendix C Trouble Shooting

TROUBLE SHOOTING FOR ERROR MESSAGES

The following information gives you the error messages and the trouble­shooting. Please adjust your systems according to the messages below. And
make sure all the components and connectors are in proper position and
firmly attached. If the errors still encountered, please contact with your
distributor for maintenance.

POST BEEP :

Currently there are two kinds of beep codes in BIOS. One code indicates
that a video error has occurred and the BIOS cannot initialize the video
screen to display any additional information. This beep code consists of a
single long beep followed by two short beeps. The other code indicates that
your DRAM error has occurred. This beep code consists of a single long
beep repeatedly.

CMOS BATTERY HAS FAILED :

This message informs you that the CMOS battery is no longer functional.
The user should replace it.

CMOS CHECKSUM ERROR :

This message informs you that the CMOS is incorrect. This error may
have caused by a weak battery. Check the battery and replace if necessary.

DISK BOOT FAILURE, INSERT SYSTEM DISK AND PRESS ENTER :

No boot device was found. This could mean that either a boot drive was
not detected or the drive does not contain proper system boot files. Insert a
system disk into Drive A: and press < Enter >. If you assumed the system
would boot from the hard drive, make sure the controller is inserted
correctly and all cables are properly attached. Also make sure the disk is
formatted as a boot device. Then reboot the system.

DISKETTE DRIVES OR TYPES MISMATCH ERROR - RUN SETUP :

Type of diskette drive installed in the system is different from the CMOS
definition. Run Setup to reconfigure the drive type correctly.

Page: C-2

Prox-1715 USER

′

S MANUAL

Appendix C Trouble Shooting

DISPLAY SWITCH IS SET INCORRECTLY :

Display switch on the motherboard can be set to either monochrome or
color. This indicates the switch is set to a different setting than indicated in
Setup. Determine which setting is correct, and then either turn off the
system and change the jumper, or enter Setup and change the VIDEO
selection.

DISPLAY TYPE HAS CHANGED SINCE LAST BOOT :

Since last powering off the system, the display adapter has been changed.
You must configure the system for the new display type.

EISA CONFIGURATION CHECKSUM ERROR
PLEASE RUN EISA CONFIGURATION UTILITY :

The EISA non-violatile RAM checksum is incorrect or cannot correctly
read the EISA slot. This can indicate either the EISA non-volatile
memory has become corrupt or the slot has been configured incorrectly.
Also be sure the card is installed firmly in the slot.

EISA CONFIGURATION IS NOT COMPLETE
PLEASE RUN EISA CONFIGURATION UTILITY :

The slot configure information stored in the EISA non-volatile memory is
incomplete.
Note: When either of these errors appear, the system will boot in ISA mode,
which allows you to run the EISA Configuration Utility.

ERROR ENCOUNTERED INITIALIZING HARD DRIVE :

Hard drive cannot be initialized. Be sure the adapter is installed correctly
and all cables are correctly and firmly attached. Also be sure the correct
hard drive type is selected in Setup.

ERROR INITIALIZING HARD DISK CONTROLLER :

Cannot initialize controller. Make sure the cord is correctly and firmly
installed in the bus. Be sure the correct hard drive is selected in Setup. Also
check to see if any jumper needs to be set correctly on the hard drive.

Prox-1715 USER′S MANUAL

Page: C-3

Appendix C Trouble Shooting

FLOPPY DISK CNTRLR ERROR OR NO CNTRLR PRESENT :

Cannot find or initialize the floppy drive controller. Make sure the
controller is installed correctly and firmly. If there are no floppy drives
installed, be sure the Diskette Drive selection in Setup is set to NONE.

INVALID EISA CONFIGURATION
PLEASE RUN EISA CONFIGURATION UTILITY

:

The non-volatile memory containing EISA configuration information was
programmed incorrectly or has become corrupt. Re-run EISA configuration
utility to correctly program the memory.
Note: When this error appears, the system will boot in ISA mode, which
allows you to run the EISA Configuration Utility.

KEYBOARD ERROR OR NO KEYBOARD PRESENT

:

Cannot initialize the keyboard. Make sure that the keyboard is properly
attached and no keys being pressed during the boot.
If you are purposely configuring the system without a keyboard, set the
error halt condition in Setup to HALT ON ALL, BUT KEYBOARD. This
will cause the BIOS to ignore the missing keyboard and continue the boot.

MEMORY ADDRESS ERROR AT ... :

Indicates a memory address error at a specific location. You can use this
location along with the memory map for your system to find and replace the
bad memory chips.

MEMORY PARITY ERROR AT ... :

Indicates a memory parity error at a specific location. You can use this
location along with the memory map for your system to find and replace the
bad memory chips.

MEMORY SIZE HAS CHANGED SINCE LAST BOOT :

Memory has been added or removed since the last boot. In EISA mode use
Configuration Utility to reconfigure the memory configuration. In ISA
mode enter Setup and enter the new memory size in the memory fields.

Page: C-4

Prox-1715 USER

′

S MANUAL

Appendix C Trouble Shooting

MEMORY VERIFY ERROR AT ... :

Indicates an error verifying a value already written to memory. Use the
location along with your system's memory map to locate the bad chip.

OFFENDING ADDRESS NOT FOUND :

This message is used in conjunction with the I/O CHANNEL CHECK and
RAM PARITY ERROR messages when the segment that has caused the
problem cannot be isolated.

OFFENDING SEGMENT :

This message is used in conjunction with the I/O CHANNEL CHECK and
RAM PARITY ERROR messages when the segment that has caused the
problem has been isolated.

PRESS A KEY TO REBOOT :

This will be displayed at the bottom screen when an error occurs that
requires you to reboot. Press any key and the system will reboot.

PRESS F1 TO DISABLE NMI, F2 TO REBOOT :

When BIOS detects a Non-maskable Interrupt condition during boot, this
will allow you to disable the NMI and continue to boot, or you can reboot
the system with the NMI enabled.

RAM PARITY ERROR – CHECKING FOR SEGMENT :

Indicates a parity error in Random Access Memory.

Should be Empty But EISA Board Found
PLEASE RUN EISA CONFIGURATION UTILITY :

A valid board ID was found in a slot that was configured as having no
board ID.
Note: When this error appears, the system will boot in ISA mode, which
allows you to run the EISA Configuration Utility.

Should Have EISA Board But Not Found
PLEASE RUN EISA CONFIGURATION UTILITY :

The board installed is not responding to the ID request, or no board ID has
been found in the indicated slot.
Note: When this error appears, the system will boot in ISA mode, which
allows you to run the EISA Configuration Utility.

Prox-1715 USER′S MANUAL

Page: C-5

Appendix C Trouble Shooting

Slot Not Empty :

Indicates that a slot designated as empty by the EISA Configuration Utility
actually contains a board.

SYSTEM HALTED, (CTRL-ALT-DEL) TO REBOOT :

Indicates the present boot attempt has been aborted and the system must be
rebooted. Press and hold down the CTRL and ALT keys and press DEL.

Wrong Board in Slot
PLEASE RUN EISA CONFIGURATION UTILITY :

The board ID does not match the ID stored in the EISA non-volatile
memory.
Note: When this error appears, the system will boot in ISA mode, which
allows you to run the EISA Configuration Utility.

FLOPPY DISK(S) FAIL (80) :

Unable to reset floppy subsystem.

FLOPPY DISK(S) FAIL (40) :

Floppy type dismatch.

Hard Disk(S) Fail (80) :

Hard Disk Drive reset failed.

Hard Disk(S) Fail (40) :

Hard Disk Drive controller diagnostics failed.

Hard Disk(S) Fail (20) :

Hard Disk Drive initialization error.

Hard Disk(S) Fail (10) :

Unable to recalibrate fixed disk.

Hard Disk(S) Fail (08) :

Sector Verify failed.

Keyboard is locked out – Unlock the key :

BIOS detect the keyboard is locked. P17 of keyboard controller is pulled
low.

Page: C-6

Prox-1715 USER

′

S MANUAL

Keyboard error or no keyboard present :

Cannot initialize the keyboard. Make sure the keyboard is attached
correctly and no keys are being pressed during the boot.

Manufacturing POST loop :

System will repeat POST procedure infinitely while the P15 of keyboard
controller is pull low. This is also used for M/B burn in test.

BIOS ROM checksum error – System halted :

The checksum of ROM address F0000H-FFFFFH is bad.

Memory test fail :

BIOS reports the memory test fail if the onboard memory is tested error.

Appendix C Trouble Shooting

Prox-1715 USER′S MANUAL

Page: C-7