protech PMB-1751LF M1 User Manual
USER’S
MANUAL
PMB-1751LF
Pentium® 4
Motherboard
With VGA / Audio/ 2LAN
PMB-1751LF M1
Copyright Notice
PMB-1751LF
Pentium® 4
Motherboard
With VGA / Audio / Dual LAN
OPERATION MANUAL
COPYRIGHT NOTICE
This operation manual is meant to assist both Embedded Computer
manufacturers and end users in installing and setting up the system. The
information contained in this document is subject to change without any
prior notice.
This manual is copyrighted March 2006. You may not reproduce or
transmit in any form or by any means, electronic, or mechanical, including
photocopying and recording.
ACKNOWLEDGEMENTS
All trademarks and registered trademarks mentioned herein are the property
of their respective owners.
CE NOTICE
This is a class A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate
measures.
Copyright Notice
FCC NOTICE
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at his own expense.
You are cautioned that any change or modifications to the equipment not
expressly approve by the party responsible for compliance could void your
authority to operate such equipment.
Contents
TABLE OF CONTENTS
CHAPTER 1 INTRODUCTION
1-1 About This Manual ....................................................... 1-2
1-2 System Specifications ................................................... 1-3
1-3 Safety Precautions ......................................................... 1-6
CHAPTER 2 HARDWARE CONFIGURATION
2-1 Jumper & Connector Quick Reference Table ............... 2-2
2-2 Component Locations ................................................... 2-3
2-3 How to Set the Jumpers ................................................ 2-4
2-4 COM Port Connector ………………………………… 2-6
2-5 RS232/422/485 (COM2) Selection ............................... 2-8
2-6 JCOM1 & COM2 (JCOM2) RI & Voltage Selection ... 2-9
2-7 COM3 & COM4 RI & Voltage Selection ……………. 2-11
2-8 Keyboard & PS/2 Mouse Connector …………………. 2-13
2-9 Reset Connector ……………...………………………. 2-13
2-10 External Speaker Connector ……………..…………… 2-14
2-11 Hard Disk Drive LED Connector .........................…..... 2-14
2-12 Power LED Connector ……………………………….. 2-14
2-13 EXTSIM# Connector.. ……………………………….. 2-15
2-14 ATX Power Button …………………………………… 2-15
2-15 Keylock Connector …………………………………… 2-15
2-16 IrDA Connector …………...………………………….. 2-16
2-17 Printer Connector ...…................................................... 2-16
2-18 ATX Power Connector ………….................................. 2-17
2-19 Clear CMOS Data Selection .......................................... 2-18
2-20 VGA Connector …………………...........................…. 2-19
2-21 USB & LAN Connector …....................................…… 2-20
2-22 USB Power Setting …………………………………… 2-22
2-23 LAN2 Enable/Disable Connector ................................. 2-23
2-24 Wake-on-modem Connector ….....................……........ 2-24
2-25 CPU Fan Connector …………..…................................ 2-24
2-26 System Fan Connector …….......................................... 2-24
2-27 Reset/NMI/Clear Watchdog Selection .......................... 2-25
2-28 Hard Disk Drive Connector …….................................. 2-26
2-29 Floppy Disk Drive Connector …................................... 2-28
2-30 Sound Connector ...............……………........................ 2-29
Contents
2-31 CD Audio-In Connector ……………............................ 2-30
2-32 Memory Installation ………………………………….. 2-31
2-33 PPCI Connector ...................……………...................... 2-32
2-34 EPPCI IRQ Selection ………………………………… 2-33
CHAPTER 3 SOFTWARE UTILITIES
3-1 Introduction ................................................................... 3-2
3-2 VGA Driver Utility ....................................................... 3-2
3-3 Flash BIOS Update ....................................................... 3-3
3-4 LAN Driver Utility ….................................................... 3-5
3-5 Sound Driver Utility ………………………………….. 3-7
3-6 Intel® Chipset Software Installation Utility …………. 3-8
3-7 USB2.0 Chipset Software Installation Utility ……….. 3-9
3-6 Watchdog Timer Configuration .................................... 3-10
CHAPTER 4 AWARD BIOS SETUP
4-1 Introduction ................................................................... 4-2
4-2 Entering Setup ............................................................... 4-3
4-3 The Standard CMOS Features …….............................. 4-4
4-4 The Advanced BIOS Features …................................... 4-8
4-5 Advanced Chipset Feature ............................................ 4-12
4-6 Integrated Peripherals ……........................................... 4-15
4-7 Power Management Setup ............................................ 4-19
4-8 PNP/PCI Configuration …............................................. 4-21
4-9 PC Health Status ……................................................... 4-23
4-10 Frequency / Voltage Control …..................................... 4-24
4-11 Load Fail-Safe Defaults ................................................ 4-25
4-12 Load Optimized Defaults …..………………………… 4-25
4-13 Password Setting ……………………………………... 4-26
4-14 Save & Exit Setup ......................................................... 4-27
4-15 Exit Without Saving ...................................................... 4-28
Contents
APPENDIX A EXPANSION BUS
ISA Bus Pin Assignment .......................................................... A-2
PCI Bus Pin Assignment …………………………………….. A-3
APPENDIX B TECHNICAL SUMMARY
Block Diagram ......................................................................... B-2
Interrupt Map ............................................................................ B-3
RTC (Standard) RAM Bank ..................................................... B-4
Timer & DMA Channels Map .................................................. B-5
I/O & Memory Map ................................................................. B-6
Page:1-1
INTRODUCTION
This chapter gives you the information for PMB-1751LF. It also
outlines the System specifications.
Section includes:
z About This Manual
z System Specifications
z Safety Precautions
Experienced users can skip to chapter 2 on page 2-1
for a Quick Start.
CHAPTER
1
Chapter 1 Introduction
Page: 1-2
PMB-1751LF USER
′
S MANUAL
1-1. ABOUT THIS MANUAL
Thank you for purchasing our PMB-1751LF Socket 478 Mainboard
enhanced with VGA/Sound/Dual LAN, which is fully PC / AT compatible.
The PMB-1751LF provides faster processing speed; greater expandability
and can handle more tasks than before. This manual is designed to assist
you how to install and set up the system. It contains four chapters. The
user can apply this manual for configuration according to the following
chapters:
Chapter 1 Introduction
This chapter introduces you to the background of this manual, and the
specifications for this system. The final page of this chapter will indicate
how to avoid damaging this board.
Chapter 2 Hardware Configuration
This chapter outlines the component locations and their functions. In the
end of this chapter, you will learn how to set jumper and how to con figure
this card to meet your own needs.
Chapter 3 Software Utilities
This chapter contains helpful information for proper installations of the
VGA utility, LAN utility, Sound utility, and Flash BIOS Update. It also
describes the Watchdog-timer configuration.
Chapter 4 Award BIOS Setup
This chapter indicates you how to set up the BIOS configurations.
Appendix A Expansion Bus
This Appendix introduces you the expansion bus for ISA BUS and PCI
BUS.
Appendix B Technical Summary
This section gives you the information about the Technical maps.
Chapter 1 Introduction
PMB-1751LF USER′S MANUAL
Page: 1-3
1-2. SYSTEM SPECIFICATIONS
z CPU (mPGA478):
Intel® Pentium® 4 processor in mPGA478 Socket.
1.5~3.06 GHz clock generator.
Front Side Bus 533/400 MHZ.
Auto detect voltage regulator.
Support H-T Tech.
z MEMORY :
Supports up to 2GB DDR SDRAM.
Two 184-pin DDR DIMM sockets on board.
z CACHE :
Built-in CPU.
z REAL-TIME CLOCK :
256-byte battery backed CMOS RAM.
Hardware implementation to indicate century rollover.
z BIOS :
Phoenix-AwardBIOS™ for plug & play function
.
Easy update 512KB flash EEPROM.
Support S/IO Setup.
z KEYBOARD CONNECTOR :
Mini DIN connector.
Supports for AT/PS2 keyboard.
z MOUSE CONNECTOR :
Mini DIN connector.
Supports for PS/2 Mouse.
z BUS SUPPORT :
External 1 ISA, 6 PCI
External 1 EPCI Bus
Chapter 1 Introduction
Page: 1-4
PMB-1751LF USER
′
S MANUAL
z DISPLAY :
Built in Intel® 845GV
Onboard 15-pin VGA D-SUB connector, support for resolution on SVGA
Monitor.
z WATCHDOG :
I / O port 0443H to Enable watchdog
I / O port 0441H to Disable watchdog
Selectable for NMI or Reset function by jumper setting
Time-out timing select 16 / 24 / 32 / 40 / 48 / 56 / 64 / 72 / 80 / 88 / 96 / 104 /
112 / 120 sec +/- 25%.
z IDE INTERFACE :
Two IDE ports support up to four IED devices.
Supports Ultra DMA 33/66/100.
z FLOPPY DISK DRIVER INTERFACE :
Support up to two Floppy Disk Drives, 3.5" (1.44M).
z USB CONNECTOR :
Three sets of USB connector & USB power (+5.0V/+5.0V Stand By)
selection.
Support up to six USB 2.0 ports.
z LAN ADAPTER :
Dual ports, Intel® 82562ET PHY & Intel® 82551QM or Intel 82541PI
(Giga LAN)
Two RJ-45 Jack onboard
LAN1: 10BaseT/100 BaseTx Ethernet
LAN2: 82541PI (10/100/1000)
Support wake-on-LAN function, with ATX power.
z SERIAL PORT :
Four high speed 16550 Compatible UARTs with Send / Receive 16 Byte
FIFOs; COM1/3/4:RS-232; COM2:RS-232/422/485
MIDI Compatible
Programmable Baud Rate Generator
Chapter 1 Introduction
PMB-1751LF USER′S MANUAL
Page: 1-5
z SOUND :
Realtek ALC202A (AC’97 Codec).
Fully Compliant AC’97 Analog I/O Component
16-Bit Stereo Full-Duplex Codec
Four Analog Line-level Stereo Inputs for Connection.
High Quality CD Input with Ground Sense
Stereo Line-Level Output
Interface: Line-In, Line-Out, Microphone, and CD Audio-In.
z HARDWARE MONITORING FUNCTION :
Monitor Voltage, CPU temperature, & Cooling fan.
If CPU Temperature is over setting, the buzzer will send out a warming.
z IRDA PORT :
5-pin Infrared port, support IrDA v1.0 SIR protocol
z PARALLEL PORT :
SPP / ECP / EPP Function.
1 port, bi-directional parallel port.
z GREEN FUNCTION :
Software supported by BIOS setup
z LED INDICATOR :
System power
Hard Disk access
LAN LED indicator
z DMA CONTROLLER :
82C37 x 2
z DMA CHANNELS :
7
z INTERRUPT CONTROLLERS :
82C59 x 2
z INTERRUPT LEVELS :
15
Chapter 1 Introduction
Page: 1-6
PMB-1751LF USER
′
S MANUAL
z OPERATING TEMPERATURE :
0 to 60°C.
z BOARD DIMENSIONS :
305mm x 244mm, 12” x 9.61”
z BOARD NET WEIGHT :
0.67 Kg.
1-3. SAFETY PRECAUTIONS
Follow the messages below to avoid your systems from damage:
1. Keep your system away from static electricity on all occasions.
2. Prevent electric shock. Don‘t touch any components of this card when the
card is power-on. Always disconnect power when the system is not in use.
3. Disconnect power when you change any hardware devices. For instance,
when you connect a jumper or install any cards, a surge of power may
damage the electronic components or the whole system.
Page 2-1
HARDWARE
CONFIGURATION
** QUICK START **
Helpful information describes the jumper & connector settings, and
component locations.
This section includes:
z Jumper & Connector Quick Reference Table
z Component Locations
z Configuration and Jumper settings
z Connector’s Pin Assignments
CHAPTER
2
Chapter 2 Hardware Configuration
Page: 2-2
PMB-1751LF USER'S MANUAL
2-1. JUMPER & CONNECTOR QUICK REFERENCE TABLE
COM Connector ….................................……...........
………………………………..…..
JCOM1, COM2
COM3, COM4
RS232/422/485 (COM2) Selection ......................…. JP3
COM1 & COM2 RI & Voltage Selection …………. JP4
COM3 & COM4 RI & Voltage Selection …………. JP1
Keyboard & PS/2 Mouse Connector ………………. JKBMS1
Reset Connector ...................................................…. JPANEL1
(13, 15)
External Speaker Connector ……….………………. JPANEL1
(1, 3, 5, 7)
Hard Disk Drive LED Connector ........................….. JPANEL1
(9, 11)
Power LED Connector ….................……………….. JPANEL1
(8, 10, 12)
EXTSMI# Connector ….................………………… JPANEL1
(2, 4)
ATX Power Button …………..…………………….. JPANEL1
(14, 16)
KEYLOCK …………………………………………. JPANEL1
(17, 18)
IRDA Connector …………………………………… IRDA1
Printer Connector .................................................…. JPRNT1
ATX Power Connector …………………………….. JATXPWR1, JATXPWR2
Clear CMOS Data Selection ……………………….. JCMOS1
VGA Connector ..........................................………... JVGA1
USB & LAN Connector ...........................…………..
Front USB Connector ...........................….………..
JRJ45USB1, JRJ45USB2
JUSB3, JUSB2 (Optional)
USB Power Setting ………………………………….
…………………………………
JUSBV1, JUSBV2,
JUSBV3
LAN2 Enable/Disable Selection ….………………... JP6
Wake-On-Modem Connector ………………………. WOL1 (JWOL1)
CPU Fan Connector .............................................….. JCFAN1
System Fan Connector ……………………………… JSFAN1, JSFAN2
Reset/NMI/Clear Watchdog Selection ……………….. JP2
Hard Disk Drive Connector .................................….. IDE1, IDE2
Floppy Disk Drive Connector ..............................….. FDD1
Sound Connector ..………………………………….. JAUDIO1
CD Audio-In Connector ….………………………… JCDIN1, JCDIN2
Memory Installation .............................................…..
DDR1, DDR2
PPCI Connector ……………………………………..
PPCI
EPPCI IRQ Selection ……………………………….
JP10
Reserved Pin ………………………………………...
JP5,JP7
Chapter 2 Hardware Configuration
PMB-1751LF USER'S MANUAL
Page: 2-3
2-2. COMPONENT LOCATIONS
PMB-1751LF Connector, Jumper and Component locations
Chapter 2 Hardware Configuration
Page: 2-4
PMB-1751LF USER'S MANUAL
2-3. HOW TO SET THE JUMPERS
You can configure your board by setting the jumpers. Jumper is consists of
two or three metal pins with a plastic base mounted on the card, and by
using a small plastic "cap", Also known as the jumper cap (with a metal
contact inside), you are able to connect the pins. So you can set-up your
hardware configuration by "opening" or "closing" pins.
The jumper can be combined into sets that called jumper blocks. When the
jumpers are all in the block, you have to put them together to set up the
hardware configuration. The figure below shows how this looks like.
JUMPERS AND CAPS
If a jumper has three pins (for example, labelled PIN1, PIN2, and PIN3),
You can connect PIN1 & PIN2 to create one setting and shorting. You can
either connect PIN2 & PIN3 to create another setting. The same jumper
diagrams are applied all through this manual. The figure below shows what
the manual diagram looks like and what they represent.
Chapter 2 Hardware Configuration
PMB-1751LF USER'S MANUAL
Page: 2-5
JUMPER DIAGRAMS
JUMPER SETTINGS
Chapter 2 Hardware Configuration
Page: 2-6
PMB-1751LF USER'S MANUAL
2-4. COM PORT CONNECTOR
Four COM ports are enhanced in this board namely: JCOM1, COM2,
COM3 and COM4. JCOM1, COM3 and COM4 are fixed for RS-232
while COM2 is selectable for RS-232/422/485.
JCOM1 : COM1 Connector, DB9 male connector
The JCOM1 Connector assignments are as follows :
PIN ASSIGNMENT
1 NDCD1
2 RXD1
3 TXD1
4 NDTR1
5 GND
6 NDSR1
7 NRTS1
8 NCTS1
9 NRI1
COM2 : COM2 Connector
The COM2 Connector assignments are as follows :
ASSIGNMENT
PIN
RS-232 RS-422 RS-485
1 NDCD2 TX- TX2 RXD2 TX+ TX+
3 TXD2 RX+ RX+
4 NDTR2 RX- RX5 GND GND GND
6 NDSR2 RTS- NC
7 NRTS2 RTS+ NC
8 NCTS2 CTS+ NC
9 NRI2 CTS- NC
10 NC NC NC
JCOM 1
Chapter 2 Hardware Configuration
PMB-1751LF USER'S MANUAL
Page: 2-7
COM3 : COM3 Connector
The COM3 Connector assignments are as follows :
PIN ASSIGNMENT
1 NDCD3
2 RXD3
3 TXD3
4 NDTR3
5 GND
6 NDSR3
7 NRTS3
8 NCTS3
9 NRI3
10 NC
COM4 : COM4 Connector
The COM4 Connector assignments are as follows :
PIN ASSIGNMENT
1 NDCD4
2 RXD4
3 TXD4
4 NDTR4
5 GND
6 NDSR4
7 NRTS4
8 NCTS4
9 NRI4
10 NC
Chapter 2 Hardware Configuration
Page: 2-8
PMB-1751LF USER'S MANUAL
2-5. RS232/422/485 (COM2) SELECTION
JP3 : RS-232/422/485 Selection
COM1, COM3, & COM4 is fixed for RS-232 function only.
COM2 is selectable for RS-232, 422, 485 function.
The jumper settings are as follows :
COM 2
Function
Jumper Setting
(pin closed)
Jumper
Illustration
RS-232
Open
RS-422
1-2, 5-6, 7-8, 9-10
11-12,13-14,15-16
17-18, 19-20
RS-485
1-3, 4-6, 7-8, 9-10
11-12,13-14,15-16
17-18, 19-20
*** Manufactory default --- RS-232.
Chapter 2 Hardware Configuration
PMB-1751LF USER'S MANUAL
Page: 2-9
2-6. JCOM1 & COM2(JCOM2) RI & VOLTAGE SELECTION
JP4: JCOM1 & COM2(JCOM2) RI & Voltage Selection
The selections are as follows:
COM PORT SELECTION
JUMPER
SETTINGS
JUMPER
ILLUSTRATION
RI 7-9
9
10
1
2
JP4
5V 1-3
9
10
1
2
JP4
JCOM1
12V 3-5
9
10
1
2
JP4
*** Manufactory default -- RI.
Chapter 2 Hardware Configuration
Page: 2-10
PMB-1751LF USER'S MANUAL
COM PORT SELECTION
JUMPER
SETTINGS
JUMPER
ILLUSTRATION
RI 8-10
9
10
1
2
JP4
5V 2-4
9
10
1
2
JP4
COM2
(JCOM2)
12V 4-6
9
10
1
2
JP4
*** 1. Manufactory default – RI.
2. JCOM2 is shared with COM2.
Chapter 2 Hardware Configuration
PMB-1751LF USER'S MANUAL
Page: 2-11
2-7. COM3 & COM4 RI & VOLTAGE SELECTION
JP1: COM3 & COM4 RI & Voltage Selection
The selections are as follows:
COM PORT SELECTION
JUMPER
SETTINGS
JUMPER
ILLUSTRATION
RI 7-9
9
10
1
2
JP1
5V 1-3
9
10
1
2
JP1
COM3
12V 3-5
9
10
1
2
JP1
*** Manufactory default -- RI.
Chapter 2 Hardware Configuration
Page: 2-12
PMB-1751LF USER'S MANUAL
COM PORT SELECTION
JUMPER
SETTINGS
JUMPER
ILLUSTRATION
RI 8-10
9
10
1
2
JP1
5V 2-4
9
10
1
2
JP1
COM4
12V 4-6
9
10
1
2
JP1
*** Manufactory default -- RI.
Chapter 2 Hardware Configuration
PMB-1751LF USER'S MANUAL
Page: 2-13
2-8. KEYBOARD & PS/2 MOUSE CONNECTOR
JKBMS1 : Keyboard & PS/2 Mouse Connector
The pin assignments are as follows :
PIN ASSIGNMENT
1 L_KDAT
2 NC
3 GND
4 VCC
5 L_KCLK
6 NC
7 L_MDAT
8 NC
9 GND
10 VCC
11 L_MCLK
12 NC
2-9. RESET CONNECTOR
JPANEL1 (13-15) : Reset Connector.
The pin assignments are as follows :
PIN ASSIGNMENT
13 GND
15 RST_BUTT
R
e
s
e
t
1
2
3
4
5
6
JKBMS1
7
8
9
Chapter 2 Hardware Configuration
Page: 2-14
PMB-1751LF USER'S MANUAL
2-10. EXTERNAL SPEAKER CONNECTOR
JPANEL1 (1,3,5,7) : External Speaker Connector
The pin assignments are as follows :
PIN ASSIGNMENT
1 SPK3
3 NC
5 NC
7 SPK VCC
2-11. HARD DISK DRIVE LED CONNECTOR
JPANEL1 (9-11) : Hard Disk Drive LED Connector
The pin assignments are as follows :
PIN ASSIGNMENT
9 VCC3_3
11 HD_LED
2-12. POWER LED CONNECTOR
JPANEL1 (8,10,12) : Power LED Connector
The pin assignments are as follows :
PIN ASSIGNMENT
8 LED+
10 LED+
12 LED-
S
p
e
a
k
e
r
H
D
D
_
L
E
D
Chapter 2 Hardware Configuration
PMB-1751LF USER'S MANUAL
Page: 2-15
2-13. EXTSMI# CONNECTOR
JPANEL1 (2,4) : EXTSMI# Connector
The pin assignments are as follows :
PIN ASSIGNMENT
2 GPIO7
4 GND
2-14. ATX POWER BUTTON
JPANEL1 (14,16) : ATX Power Button
The pin assignments are as follows :
PIN ASSIGNMENT
14 PW_BN1
16 PW_BN2
2-15. KEYLOCK CONNCETOR
JPANEL1 (19,20,21,22,23,24) : KEYLOCK Connector
The pin assignments are as follows :
PIN ASSIGNMENT
17 KEYLOCK
18 GND
A
T
X
-
B
T
N
KEYLOCK
Chapter 2 Hardware Configuration
Page: 2-16
PMB-1751LF USER'S MANUAL
2-16. IRDA CONNECTOR
JPANEL1 (19,20,21,22,23,24) : Infrared Connector.
Share with IRDA1.
The pin assignments are as follows :
PIN ASSIGNMENT
19 GND
20 NC
21 VCC5
22 GND
23 IRTX2
24 IRRX2
2-17. PRINTER CONNECTOR
JPRNT1 : Printer Connector
The pin assignments are as follows :
JPRNT1
PIN ASSIGNMENT PIN ASSIGNMENT
1 STB 14 AFD
2 P0 15 ERR
3 P1 16 INIT
4 P2 17 SLIN
5 P3 18 GND
6 P4 19 GND
7 P5 20 GND
8 P6 21 GND
9 P7 22 GND
10 ACK 23 GND
11 BUSY 24 GND
12 PE 25 GND
13 SLCT
I
R
D
A
Chapter 2 Hardware Configuration
PMB-1751LF USER'S MANUAL
Page: 2-17
2-18. ATX POWER CONNECTOR
JATXPWR1 : ATX Power Connector
The pin assignments are as follows :
JATXPWR1
20
10
1
11
PIN ASSIGNMENT
1 +3.3V
2 +3.3V
3 GND
4 +5.0V
5 GND
6 +5.0V
7 GND
8 Power Good
9 +5.0V Standby
10 +12.0V
11 +3.3V
12 -12.0V
13 GND
14 Power On
15 GND
16 GND
17 GND
18 -5.0V
19 +5.0V
20 +5.0V
Loading...