MPEG4
STAND-ALONE
DVR
M
User’s Manual
■ Some system menu can be different from each model
■ Some system menu is subject to change by firmware upgrade
■ Please read this manual carefully before running DVR system
MPPEEGG
4 S
4 STTAANNDD--AALLOONN
E D
E DVVRR
K
K
K
P
P
P
D
D
D
-
-
-
M
M
M
S
S
S
e
e
e
r
r
r
i
i
i
e
e
e
s
s
s
CAUTION
TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT OPEN COVERS.
NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Please beware of the following precautions before installing the DVR.
Avoid any place with moisture, dust, or soot.
Avoid any place with direct sunlight or heating appliances.
Keep the product away from electric shock or magnetic substances.
Avoid high or low temperature.
(Recommended operation temperature is between 0°C ~ 40°C).
Do not place any conductive material through the ventilation.
Turn off the system before installation.
Ensure enough space for cable connections.
Place the system on a solid surface with sufficient air ventilation.
Avoid any surface that vibrates.
Placing the system near electronic devices such as radio or TV may cause
breakdown to the product.
Do not disassemble the product without assistance from the manufacturer.
Do not place any heavy object on the system.
NOTE
This equipment had been tested and found to comply with the limits for a CLASS A digital
device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment.
PLEASE READ THIS MANUAL THOROUGHLY FOR EFFECTIVE AND SAFE USAGE OF
THE DEVICE.
2
CONTENTS
I. KEY FEATURES ------------------------------------------------------------------- 5~6
II. UNIT PACKAGE ------------------------------------------------------------------ 7
III. BUTTON AND CONNECTION ----------------------------------------------- 8~11
IV. REMOTE CONTROLLER ----------------------------------------------------- 12
V. OPERATION ---------------------------------------------------------------------------------------- 13~20
1. POWER ON -------------------------------------------------------------------------------------- 13
2. LOG IN SYSTEM ------------------------------------------------------------------------------- 13
3. RECORD ------------------------------------------------------------------------------------------ 13
4. LIVE MODE -------------------------------------------------------------------------------------- 14~15
5. SEARCH MODE ---------------------------------------------------------------------------- 16~17
6. FUNCTION --------------------------------------------------------------------------------------- 18~20
VI. SYSTEM SETUP ---------------------------------------------------------------------------------- 21~40
z THE TABLE OF MENU --------------------------------------------------------------------- 21~22
1. SYSTEM ---------------------------------------------------------------------------------------- 23~26
1-1 PASSWORD ------------------------------------------------------------------------------ 23
1-2 TIME -------------------------------------------------------------------------------------- 24~25
1-3 PTZF PROTOCOL -------------------------------------------------------------------------- 25
1-4 STORAGE ------------------------------------------------------------------------------------- 25~26
1-5 CHANGE LANGUAGE ------------------------------------------------------------------- 26
1-6 SOFTWARE UPDATE ------------------------------------------------------------------ 26~27
1-7 SETUP DATA ----------------------------------------------------------------------- 27~28
2. DISPLAY ------------------------------------------------------------------------------------------ 28~30
2-1 SEQUENCE DWELL (SINGLE) ----------------------------------------------------------- 28
2-2 SEQUENCE DWELL (GROUP) ----------------------------------------------------------- 28
2-3 CAMERA NAME ---------------------------------------------------------------------------- 28
2-4 CAMERA STATUS ------------------------------------------------------------------------- 29
2-5 CAMERA COLOR -------------------------------------------------------------------------- 29
2-6 SPOT DWELL (SINGLE) --------------------------------------------------------------------- 29
2-7 SPOT DWELL (GROUP) -------------------------------------------------------------------- 30
2-8 VGA FREQUENCY CHANGE ------------------------------------------------------------ 30
2-9 VIDEO STANDARD ------------------------------------------------------------------------- 30
3. RECORD -------------------------------------------------------------------------------------------- 31~35
3-1 REC PROPERTY ---------------------------------------------------------------------------- 31
3-2 REC OPTIONS ------------------------------------------------------------------------------- 31~32
3-3 EVENT REC ----------------------------------------------------------------------------------- 32~34
3
3-4 SCHEDULE REC ---------------------------------------------------------------------------- 34
3-5 DELETE REC --------------------------------------------------------------------------------- 35
3-6 LOCK/UNLOCK ------------------------------------------------------------------------------ 35
3-7 DELETE ALL REC -------------------------------------------------------------------------- 35
4. NETWORK ------------------------------------------------------------------------------------------ 36~38
4-1 NETWORK TYPE ---------------------------------------------------------------------------- 36
4-2 DDNS ------------------------------------------------------------------------------------------- 37
4-3 NET PASSWORD --------------------------------------------------------------------------- 37
4-4 NET CLIENT PORT ------------------------------------------------------------------------- 37
4-5 NET CLIENT ID ------------------------------------------------------------------------------ 38
4-6 NET DVR ID -------------------------------------------------------------------------------------- 38
4-7 NET CLIENT ADDR ------------------------------------------------------------------------- 38
4-8 NETWORK THROUGHPUT -------------------------------------------------------------- 38
4-9 WEB PORT ---------------------------------------------------------------------------------
5. SENSOR / AUDIO -------------------------------------------------------------------------------- 39~40
5-1 SENSOR TYPE ------------------------------------------------------------------------------ 39
5-2 ALARM MOTION MANAGER ------------------------------------------------------------ 39
5-3 ALARM SENSOR MANAGER ----------------------------------------------------------- 39
5-4 ALARM BUZZER ---------------------------------------------------------------------------- 40
5-5 ALARM OUTPUT ---------------------------------------------------------------------------- 40
5-6 ALARM OUT PERIOD ---------------------------------------------------------------------- 40
5-7 AUDIO ------------------------------------------------------------------------------------------ 40
* HDD INSTALLATION ------------------------------------------------------------------------------- 41
* TROUBLE SHOOTING ------------------------------------------------------------------------------- 42
4
KEY FEATURES
Operation
Embedded LINUX OS
Enhanced MPEG4 compression
Display, Playback, Recording, Network transmission
Real time single or multi-screen display
Easy operation by IR remote controller
Hidden camera option (covert)
Easy firmware update by network and USB 2.0
Playback
Multi-screen playback
Search by time, event and calendar with go first/last function
Simple playback – automatic download of viewer software at backup
Recording
Recording resolution and quality level adjustable
Recording frame rate can be set by user
The recording speed of max. 120/100 images per second (NTSC/PAL)
Continuous, manual, schedule and event (motion, alarm) recording
Pre-alarm/post alarm recording
Delete and lock/unlock recording video available
4 channel audio recording
Alarm pop-up
Event log view
Network
Live, playback with viewer software and IE(Internet Explorer)
Remote control via networked PC with the exclusive client viewer
Supporting Static, DHCP, DDNS, PPPoE
Multi-user connection available
Live and Recording audio File play in network
5
KEY FEATURES
Audio
4 channel audio recording in real time
1 channel audio output
Backup
Remote backup on network PC with the exclusive client viewer
CD-RW (DVD-RW) backup
USB 2.0 backup( Both USB stick and USB connection HDD available)
General
Auto detection of video frequency(NTSC/PAL)
Built-in hardware Watchdog
S-Video output
Alarm In/Out, RS-485, RS-232 Connections
Loop-through connections
Multiple Languages
VGA output for PC monitor
6
UNIT PACKAGE
MPEG4 DVR System
Viewer Program/Manual Install Guide Remote controller
LAN cable Power cord
Battery HDD screws DC adaptor
(DC12V 5A)
7
BUTTON AND CONNECTION
1-1 FRONT PANEL
9
1
1. Channel Selection
You select a channel as full-size screen during live display or playback. When the number is
above 10, please press the ‘+10’ button at first and press other number.
2. USB 2.0 slot
It is used when you upgrade firmware update and backup video files.
3. MULTI
When you press the button repeatedly, you can change the screen display mode as you want
from PIP to multi channel to single channel view.
4. AUTO
The function allows users to watch individual channels by rotating every channel in turn
automatically. Please press the button again to stop it
5. PIP (Picture in Picture)
If you press the button, you can see a master channel and a slave channel on the master
simultaneously. Press the button again, and master becomes slave and vise versa.
6. MUTE
You can turn off the audio.
7. INFO
INFO key shows system information of DVR only in live display mode.
8. OSD
If you do not need OSD, press the button. Pressing one more time retrieve the OSD.
9. BACKUP
You can backup video in CD-RW (DVD-RW) or USB (Memory stick and exterior HDD) in
playback mode.
10. LED Lights
You can identify how power, record, HDD and network(NET) are.
11. MENU
You can change DVR settings. When you want to return to the previous step, press the button
again.
8
BUTTON AND CONNECTION
12. SEARCH
You can choose the video file you want to find through this key.
13. REC
You can manually record by pressing the button. Press it once more, and you can stop
recording.
14. Playback
REW (◀◀): Rewind the video (up to 128x)
PLAY/PAUSE (▶/II): Play and Pause the video
FAST (▶▶): Fast forward the video (up to 128)
STOP (■): Stop the video.
15. PTZ
When you want to control speed dome cameras, please press the button.
16. Control keys
You can shift up, down, right and left and select what you want to.
9
BUTTON AND CONNECTION
1-2 REAR PANEL
KPD-M1601
KPD-M901
KPD-M401
1. Audio In
RCA 4 channel audio inputs
2. Video Input
Max 16 channel video inputs
3. Loop out
Max 16 channel video loop outputs
4. Power switch
5. Power Input
Input: 100V~240VAC 50/60Hz 1.5A
Output: DC 12V, 5A
6. SEN. IN/AL/485
Sensor In:16Ch(1~16), 9Ch(1~9), 4Ch(1~4)
17-20: Alarm Out, 21: 485+, 22: 485-, 23-25: GND
12
10
BUTTON AND CONNECTION
7. RS232
Connection port for engineering use only
8. VGA
VGA output connecting to LCD monitor
9. USB
USB 2.0 for system update and video backup
10. LAN
LAN connecting to a variety of networks
11. Audio Out
RCA 1 channel audio output
12. S-Video
Connecting to S-Video monitor
13. Video Out
Connecting to monitor
KPD-M401: 2 outputs, KPD-M901/1601: 1 output
14. Spot Out (*KPD-M901/1601)
Connecting to spot monitor
11
HDD INSTALLATION
1. REC (Record)
2. Channel Selection
You select a channel as full-size screen
during live display or playback. When the
number is above 10, please press the ‘+10’
button at first and press other number.
3. REC STOP: Record stop button
4. INFO: DVR Information
5. P/T: Pan, Tilt
6. Z/F: Zoom, Focus
7. OSD: OSD on/off
8. MENU
9. LOG: Log list view
10. SEARCH
11. Direction keys(▲, ▼, ◀, ▶)
: Move cursor or control PTZF Camera
12. MUTE
13. BACKUP
14. Playback control keys
15. SPOT
16. PIP
17. POP
18. AUTO
19. Multi display modes
12
HDD INSTALLATION
1. Power on
Press power button on rear of the unit.
If system begins, loading message will appear. (It takes around 30seconds to boot DVR
system)
2. Log in system
Enter your password (Default : 0000) to Log-
ENTER PASSWORD
in the system
- - - -
a. To change your password, please refer Page 23.
b. Administration password pops up when users press
MENU button.
ENTER ADMIN PASSWORD
- - - -
3. Record
Press REC button to record the video. If you press REC button once more, recording
will be stopped.
BEFORE RECORDING, PLEASE CHECK!!
,,,(1) Check out whether the date and time are
,,,,,correctly set.
,,,(2) Check out whether HDD is formatted.
,,,,,,,,,If HDD is not formatted, please format HDD.
,,,,,,,,,Æ Please refer Page 27 to format HDD
,,,(3) Make sure that each camera screen displays
,,,,,properly.
,,,(4) Set up the camera channel name.
,,,(5) Select recording quality.
,,,(6) Select recording method.
,,,(7) Recording can be stopped by pressing REC
,,,,,,,,button again. To keep recording, we recommend
,,,,,,,,you to set recording mode in “CONTINUOUS”.
13
HDD INSTALLATION
,,,,,,,Æ Please refer Page 31.
4. Live mode
4.1 Display on screen
4.2 Display of full screen mode
4-3. Quad screen (*Remote control)
To see quad screen when the full screen mode, press button.
4-4. Full screen (*Remote control)
To see specific camera by full screen, press button
4-5. 9ch display mode (*Remote control)
* KPD-M901 / M1601
To see cameras by 9ch mode, press button
4-6. 16ch display mode (*Remote control)
* KPD-M1601
To see camera by 16ch mode, press button
4-7. POP mode (*Remote control)
* KPD-M901 / M1601
Press POP button to enlarge specific camera.
Whenever pressing POP button, go to next camera.
4-8. Auto Sequence (Auto)
Interval display on the monitor before going to the next channel.
the default time span from one channel to another is 2 seconds.
User can select the range of time from 1 to 60 seconds.
Date / Time
Current mode
LIVE : Live video
2006/09/25-11:11:25 LIVE
PLAY : Playback
USB : USB equipment is connected
REC : Recording
>> : Fast forward
Speed rate on playback
HDD status
<< : Fast rewind
S
p
eed rate on playback
MA-A:99%
SL1-B:NONE
Current mode
Camera status
HDD status
Date / Time
LIVE : Live video
PLAY : Playback
REC : Recording
>> : Fast forward
Speed rate on playback
<< : Fast reward
Speed rate on playback
LIVE
1 R M S
1 : Camera No.
R : Record
M : Motion
S : Sensor
MA-A:90%
2006/02/01-12:00:07
SL1-B:NONE
POP
14
HDD INSTALLATION
If you want to change interval time to rotate the camera, please go to ‘MENU’ and
setup the interval time.
4-9. PIP
When it is in full screen display mode, you can see other camera in a small window.
(1) Press PIP button of remote controller to go to PIP mode
(2) If you press this button in PIP mode, the position of two cameras will be swapped.
1
2
2
‘PIP’ Button
1
(3) Press Camera button in PIP mode to change small screen to another camera.
Example)
1
2
1
3
Cam ‘3’ Button
(4) Press Direction button to move small window at appropriate position.
15
HDD INSTALLATION
5. Search mode
(1) Press Search button
(2) Select Search method by using ▲▼ button and press ‘ENTER’ button
Search data by Year /Month/Day/Time
TIME SEARCH
[SEARCH]
Search only Data recorded by motion
detection function
EVENT SEARCH
* TIME SEARCH
5-1. TIME SEARCH
(1) If you select TIME SEARCH, Time Search table will appear
(2) Key in the year, month, day and time that you want to search for.
(3) Press the Enter key.
5-2. EVENT SEARCH
(1) If you select EVENT SEARCH, the calendar will appear.
(2) Select desired date by using ◀▶▲▼ button and press ‘ENTER’ button
(3) Select desire video clip in the list by using ▲▼ button and press ‘ENTER’
button.
* The specifications of Event list
CALENDAR SEARCH
Search data in calendar
* EVENT SEARCH
GO FIRST
Search from the top of the list
* CALENDAR SEARCH
GO LAST
Search from the bottom of the list
* GO FIRST
* GO LAST
[TIME-SEARCH]
YEAR : 0000
MONTH : 00
DAY : 00
TIME : 00:00
[CALENDAR-EVENT SEARCH]
EVENT LIST 1/2
<<2006-09>>
SUN MON TUE WED THU FR I SAT
1 2
3 4 5 6 7 8 9
10 11 12 13 14 15 16
17 18 19 20 21 22 23
24 25 26 27 28 29 30
0013 060910:230233 FL MD 01 08 09
0012 060910:225033 FL MD 01 07 09
0011 060910:224233 FL MD 01 08 09
0010 060910:223233 FL MD 01 08 16
0009 060910:215233 FL MD 01 08 09
0008 060910:213233 FL MD 01 08 09
0007 060910:210233 FL MD 01 08 09
PGDN:< PGUP:> LAST:<< FIRST:>>
EVENT LIST 1/7
00078 200507 1000 FL MD 01 02 03 04 L
PGDN:< PGUP:> LAST : << >
05:12
FIRST:>
Date / Time MD : Motion detection
SD : Sensor detection
File
Lock/Unlock
Current page / Total pages
Recorded camera No
16
HDD INSTALLATION
5-3. CALENDAR SEARCH
(1) If you select CALENDAR SEARCH, the calendar will appear.
(2) Select desired date by using ◀▶▲▼ button and press ‘ENTER’ button
(3) Select hour and minute that you want to search. The hour bar is divided into 24 sectors
(unit of one hour), and the minute bar is done into 30 sectors (unit of two minutes).
[SEARCH-TIME]
5-4. GO FIRST
(1) If you select GO FIRST, you can play back from the top file of the list to bottom.
5-5. GO LAST
(1) If you select GO LAST, you can play back from the bottom of the list.
5-6. Playback
If you press Play button in live mode, the video clip recorded recently will be
played.
If you want to see specific camera by full screen, press camera button.
For display of quad mode from full screen, press quad button.
You can control playback speed with ◀◀ / ▶▶ button. Once you press the
◀◀
REWIND / Frame
by frame
- X2, X4, X8, X16, X32, X64, X128
- Reduce Fast Forward speed while Fast Forward play
- Reverse playback frame by frame during PAUSE mode
▶I
PLAY / PAUSE Play the video and pause the video
▶▶
FAST FORWARD
/ Frame by frame
- X2, X4, X8, X16, X32, X64, X128
- Reduce Fast Reward speed while Fast Rewind
- Forward play frame by frame during PAUSE mode
■
STOP Stop the playback and go to Live mode
<<2006-09>>
SUN MON TUE WED THU FR I SAT
1 2
3 4 5 6 7 8 9
10 11 12 13 14 15 16
17 18 19 20 21 22 23
24 25 26 27 28 29 30
HOUR:
MIN:
TIME : 00:00:00
17
HDD INSTALLATION
6. Function
6-1. INFO
Show the present status of DVR system
If you press direction button (▶), detailed information is shown.
(Normal informationÆ REC information Æ S/W informationÆ HDD information)
S/W VERSION
Software version
[STATUS]
HDD
Indicate each HDD capacity and
Used capacity
S/W VERSION : VO.9.0-BY-16
(07/11/05 20:40)
[HDD] MA:75G ( 10%) SL1: NONE
NETWORK
Indicate the information of Static or
Dynamic IP address
SL2:36G(0%) SL3: NONE
NETWORK : STATIC 192.168.1.200
MAC
Indicate DVR own MAC address
MAC : 00.0E.B5.00.0C.B6
DDNS : DDNS OFF
DDNS
Indicate the statue of DDNS
service
WEB PORT : 80
NEXT INFO : RIGHT KEY
[REC]
SIZE
Recording resolution
CH
Camera No.
[REC]
SIZE : 360X240
CH RATE QUALITY CH RATE QUALITY
RATE
Statue of frame rate for recording
1 30 NORM 9 30 NORM
2 30 NORM 10 30 NORM
3 30 NORM 11 30 NORM
Indicate recording quality
QUALITY
(BEST/HIGH/NORMAL/BASIC)
4 30 NORM 12 30 NORM
5 30 NORM 13 30 NORM
6 30 NORM 14 30 NORM
7 30 NORM 15 30 NORM
8 30 NORM 16 30 NORM
KERNEL : Unknown
BOOT LOADER : Unknown
ENC. FIRMWARE : 20051031_0
DEC. FIRMWARE : 20051031_0
APPLICATION : 1.0.7
UI VER : 1.0.5-F16
DECODER VER : 1.4.0-0
ENCODER VER : 1.0.2-1
NETWORK VER : 1.0.5-3
DB VER : 1.0.1-3
MA : 20050412_084000_nCw.ps
20050427_162000_pCw.ps
SL1 : HARD DISK NOT EXIST
SL2 : CD-ROM
SL3 : HARD DISK NOT EXIST
18
HDD INSTALLATION
6-2. MUTE
When you press MUTE key, AUDIO setup window appears. Press the enter key
when you set mute mode or Audio on. FYI, Audio works only full screen mode.
[AUDIO]
STATUS : ▷ MUTE
6-3. BACKUP
User can backup the data to USB stick (USB HDD) or built-in CD (DVD)-RW.
(1) Connect USB equipment to USB port of DVR system.
(2) Press ‘BACKUP’ button.
(3) Select a method and press ‘ENTER’ button.
CD-R
6-4. PTZ (Pan / Tilt )
Press the PTZ button. Users can control PAN/TILT camera by direction button.
MEDIA TYPE
CD-RW
DVD-R
DVD-RW
USB MEMORY
① Select device to backup
[BACKUP]
MEDIA TYPE : ▷ CD-R
FILE FORMAT : ▷ NATIVE
BACKUP BASE : ▷ FILE
FILE
FORMAT
NATIVE
② Select backup file
CHANNEL : ▷ ALL
[*] 1 [*] 2 [*] 3 [*] 4
BACKUP
BASE
FILE
③ Select backup type
TIME
[*] 5 [*] 6 [*] 7 [*] 8
[*] 9 [*] 10 [*] 11 [*] 12
ALL
CAMERA
[.]1~[.]16
④ Select camera to backup
[*] 13 [*] 14 [*] 15 [*] 16
START :
START
⑤ Start time to backup file
END :
END
⑥ End time to backup file
TOTAL SIZE : 0M
TOTAL SIZE
⑦ Indicate total size to backup
BACKUP FORMAT MEDIA
⑧ Select BACKUP and press ‘ENTER’ button
⑨ In case of CD/DVD-RW, you can erase data in media by
FORMAT MEDIA.
CH: 01
Press direction button to set the PTZ
camera channel.
PTZF
<< CH: 01 >>
<< PAN :>>
Press direction button to move camera
up and down.
PAN
<< TILT :>>
<< ZOOM >>
TILT
Press direction button to move camera
right and left.
<< FOCUS>>
Press direction button to zoom in and
out.
ZOOM
Press direction button to focus the video
images.
FOCUS
19
HDD INSTALLATION
6-5. LOG LIST (*Remote controller only)
Show all information about what happened to DVR system during operation.
* Example of Log list
Event Meaning Description
MD
Motion Detection Detect motion
SD
Sensor Detection Detect sensor
VL
Video Loss No video
SY
System Change system setup
FL
File Delete or Create a file
PW
Power Power On / Off
NT
Network Access system by network
HD
Hard Disk Information of HDD
DB
Data Base Information of data base
① Select Log view type and press ‘ENTER’ button
ALL Show all information
EVENT TYPE
PART Show desired information
② Select desired sub-items and press ‘ENTER’ button
when you choose “PART”.
FROM
③ Input desired start time
TO
④ Input desired end time
⑤ Select OK and press ‘ENTER’ button
[EVENT LOG VIEW]
EVENT TYPE : ALL
MOTION : [.] SENSOR: [.]
ALARM : [.] V-LOSS : [.]
SYSTEM: [.] HDD : [.]
FILE : [.] DB : [.]
POWER : [.] NET : [.]
FROM: 2005-11-05 00:00
TO: 2005-11-05 23:59
OK CANCEL
1234 060123:095436 MD OOOOOOOOOOOO
No. Event date / time Event. Detailed information
20
OPERATION
Tips for setup of DVR system
(1) Press ‘MENU’ button to setup DVR system.
(2) The window for password input will appear.
(3) Enter your Password. (Default : 0000)
(4) Select desired sub-menu item with Direction button.
(5) Press ‘ENTER’ button to go to submenu or save system.
(6) Press ‘MENU’ button to go to previous mode without save or escape system menu.
(7) How to use text input dialog box when you need to input a text to system
1) When text input dialog box appears, select
desired alphabet and mark by Direction button.
[TEXT INPUT DIALOG]
A B C D E F G H I J
2) Press ‘ENTER’ button to input text.
K L M N O P Q R S T
3) Then, the selected text will appear.
U V W X Y Z ←
a b c d e f g h I j
4) Press ‘MENU’ button to quit dialog box.
k l m n o p q r s t
u v w x y z . ~ / :
0 1 2 3 4 5 6 7 8 9
_ - @ SPACE
CH 01
--------------------------
The Table of MENU
MENU SUB MENU DESCRIPTION
1-1-1.ADMIN PASSWORD Change system password for administrator
1-1-2.USER PASSWORD Change system password for user
1-1.PASSWORD
1-1-3.PASSWORD CHECK Activate system password
1-2-1.TIME SETUP Setup current time
1-2-2.TIME FORMAT Setup time format
1-2.TIME
1-2-3.TIME OSD FORMAT Set TIME OSD color and position on screen
1. SYSTEM
1-3.PTZF PROTOCOL Set PTZF cameras
1-4.STORAGE Format HDD / Overwrite setting
1-5.CHANGE LANGUAGE Change Language of Menu
1-6.SOFTWARE UPDATE Upgrade System Software
1-7. DEFAULT SETUP Set the system as to factoring default
2-1.SEQUENCE DWELL(SINGLE) Set switching time interval on Live full display
2-2.SEQUENCE DWELL(GROUP) * 9/16ch Set switching time interval on Live quad display
2-3.CAMERA NAME Input Camera name
2. DISPLAY
2-4.CAMERA STATUS Show or Hide a specific camera
2-5.CAMERA COLOR Control the color of camera
2-6.SPOT DWELL (SINGLE) * 9/16ch Set switching time interval on full display of Spot
21
OPERATION
2-7.SPOT DWELL (GROUP) * 9/16ch Set switching time interval on quad display of Spot
2-8.VGA FREQUENCY CHANGE Change VGA frequency
2-9.VIDEO STANDARD Set the video standard
3-1.REC PROPERTY Set recording property (Resolution/Quality/Frame rate)
Set recording option
3-2.REC OPTIONS
(Continuous / DEINTERLACE / Water mark )
3-3.EVENT REC Set Motion / Sensor
3-4.SCHEDULE REC Set schedule recording
3. REC
3-5.DELETE REC Delete record file
3-6.LOCK/UNLOCK REC Protect specific file from delete
3-7.DELETE ALL REC Delete all files
4-1.NETWORK TYPE Set the present network system (Static / Dynamic)
4-2.DDNS Set network for DDNS
Assign password to access the DVR system by Net-client
software
4-3.NET PASSWORD
4-4.NET CLIENT PORT Assign port for port-forwarding in user’s router
4. NETWORK
Assign additional ID and password to access the DVR
system by Net-client software
4-5.NET CLIENT ID
4-6.NET DVR ID For system check of net client when network connection
Limit Client IP address to access DVR system
4-7.NET CLIENT ADDR * With only registered IP address, allow user to access
DVR system
4-8.NETWORK THROUGHPUT Set the speed of data transmission in DVR system
5-1.SENSOR TYPE Set present network system (Static / Dynamic)
5-2.ALARM MOTION MANAGER Set Alarm output when motion is detected
5-3.ALARM SENSOR MANAGER Set Alarm output when sensor is detected
5. SENSOR /
SOUND
5-4.ALARM BUZZER Set Alarm buzzer ON/OFF
5-5.ALARM OUTPUT Set Alarm output ON/OFF to each camera
5-6.ALARM OUT PERIOD Set working time of Alarm output
5-7.AUDIO Set audio on designated channel
22
OPERATION
1. SYSTEM
1-1. PASSWORD
1-1-1 . ADMIN PASSWORD
Admin password is for administrator. With this password, user can access to all
menus of system. Password consists of only four digit numbers.
(1) Enter new Password to change by using Number button.
(2) Enter new Password again to confirm the Password.
[ADMIN PASSWORD]
[ADMIN PASSWORD]
CONFIRM NEW ADMIN PASSWORD
ENTER NEW ADMIN PASSWORD
: _ _ _ _
_ _ _ _
1-1-2. USER PASSWORD
(1) Enter new Password to change by using Number button.
(2) Enter new Password again to confirm the Password.
[USER PASSWORD]
[USER PASSWORD]
CONFIRM NEW ADMIN PASSWORD
ENTER NEW ADMIN PASSWORD
: _ _ _ _
_ _ _ _
1-1-3. PASSWORD CHECK
(1) Select desire sub-menu to setup by using ▲▼ button and press ‘ENTER’ button
ADMIN : Access all system
[CHECK PASSWORD]
USER : Only for logging on system
ADMIN : ON
USER : ON
(2) Select OFF or ON
[CHECK PASSWORD]
ON : can access the system after confirmation of Password
- OFF
OFF : can access the system without Password input
-
(3) Press ‘MENU’ button to go to previous mode.
In case you forgot the passwords, please press the keys in the remote controller.
INFO->MUTE->SEARCH->■->
When you press the keys in turn, you can see ‘Factory Setup’ mode to reset the
password again. If the reset password works correctly, you have to set the DVR
into the factory default in System menu.
23
OPERATION
1-2. TIME
1-2-1. TIME SETUP
(1) Select desired sub-menu by direction button and enter Year / Month / Day / Time by
using Number button.
(2) New window will appear. Press ‘ENTER’ button to change time. If you really want to
change, press Yes, otherwise No.
WARNING!!!
TIME WILL BE CHANGED
THE FILES AFTER CHAHGED
TIME WILL BE DELETED
Are you sure?
[ENTER] Æ YES, [MENU]Æ NO
TIME SETUP
YEAR : 0000
If you change the date/time to previous date/time, previous recorded data can be
deleted as follows.
So, strongly recommended to backup data before
changing time.
Changed new date/time previous date/time
DATA FILE
1-2-2. TIME FORMAT
(1) Select desire TIME format by direction button and press ‘ENTER’ button.
If the date is Dec 30th 2006
FORMAT DISPLAY
YY/MM/DD
2006/12/30
DD/MM/YY
30/12/2006
MM/DD/YY
12/30/2006
<Format description>
MONTH : 00
DAY : 00
TIME : 00:00
This part of data file will be deleted
[TIME FORMAT]
- YY / MM / DD
- DD / MM / YY
- MM / DD / YY
24
OPERATION
1-2-3. TIME OSD FORMAT
(1) Select desire position and color of time format and press
‘ENTER’ button.
[TIME OSD FORMAT]
TOP-WHITE
TOP-BLACK
BOTTOM-WHITE
BOTTOM-BLACK
OFF
2005/06/20 2005/06/20
TOP-WHITE TOP-BLACK
BOTTOM-BLACK BOTTOM-WHITE
OFF
2005/06/20 12:30:05
2005/06/20 12:30:05
2005/06/20 12:30:05
2005/06/20 12:30:05
1-3. PTZF PROTOCOL
(1) In PTZF protocol menu, select sub-item of desire camera and press ‘ENTER’
button to set
[PTZF PROTOCOL]
CH ID PROTOCOL BAUD SPEED
01 ▷000 ▷PELCO_D ▷2400 ▷9
02 ▷000 ▷PELCO_D ▷2400 ▷9
03 ▷000 ▷PELCO_D ▷2400 ▷9
04 ▷000 ▷PELCO_D ▷2400 ▷9
05 ▷000 ▷PELCO_D ▷2400 ▷9
06 ▷000 ▷PELCO_D ▷2400 ▷9
(2) ID : Enter PTZF camera ID (From 000 to 255)
(3) PROTOCOL : Select appropriate protocol.
* Available protocol: Pelco D, Pelco P, Chubb i SD, COP, LILIN, CYNIX, DSC230…
(4) BAUD : Select appropriate BAUD rate
(5) SPEED : Select desire speed for Pan tilt camera
(6) Press ‘MENU’ button to finish the setting
1-4. STORAGE
1-4-1. OVER WRITE
Select YES or NO
OVER WRITE
(When you choose YES, new
video files can be overwritten on
recorded ones.)
[STORAGE]
- NO
OVER WRITE : ▷ YES
- YES
HDD-A : FORMAT
HDD-B : NONE
HDD-C : NONE
HDD-D : NONE
25
OPERATION
1-4-2. FORMAT
When you install HDD in DVR system, you need to format HDD.
Make sure that Format function will erase all data file in HDD, which is an
unrecoverable command.
Completing the formatting, the message (“DISK FORMAT COMPLETE”) will
appear. Press the MENU button, and it returns to STORAGE window. If
there’s more HDD to format, you can format them again. If not, press MENU
button. DVR will reboot automatically.
[CHANGE LANGUAGE]
ENGLISH
PORTUGUESE
RUSSIAN
[SOFTWARE UPDATE]
- NETWORK UPDATE
- USB UPDATE
[SOFTWARE UPDATE-USB]
WARING
Firmware update will start !!!
Make sure the new firmware is in USB device.
Don’t power off during firmware update
[ENTER] ->YES , [MENU]->NO
PROGRESS FORMAT
55%
WARNING!!!
Yes
HDD-A
WILL BE FORMATTED
ARE YOUR SURE?
[
‘ENTER’] ->YES [‘MENU’]->NO
When the HDD detection status is “N/F”, recording function doesn’t work. You have to
format the HDD in N/F before recording.
1-5. CHANGE LANGUAGE
(1) Press ‘ENTER’ button “Change Language”.
(2) Select desired language and press ‘ENTER’ button.
1-6. SOFTWARE UP DATE
There are two methods to upgrade the DVR system.
USB UPDATE : Upgrade the DVR system by using USB memory stick.
NETWORK UPDATE : Upgrade the DVR system through Internet
After software update, user must turn DVR into Default values in SYSTEM.
1-6-1. USB UPDATE
(1) Copy provided Firmware file to your USB memory stick
The firmware file should be in Root directory of USB memory
26
OPERATION
(2) Connect USB memory stick to USB port in unit.
(3) Press ‘MENU’ button and go to Software Update
(4) Select USB UPDATE and press ‘ENTER’ button to proceed with software upgrade.
(5) After completing upgrade, the system will reboot automatically.
(6) Then, Check S/W version through INFO menu.
1-6-2. NETWORK UPDATE
[SOFTWARE UPDATE] [SOFTWARE UPDATE-NETWORK]
[DEFAULT SETUP]
WARNING
Are You Sure?
[‘ENTER’] ->YES , [‘MENU’]->NO
SERVER IP : videonetserver.com
- NETWORK UPDATE
- USB UPDATE FILE NAME : kpro-16.tar.gz
UPDATE CANCEL
(1) Check the unit is connected to the Internet.
(2) Press ‘MENU button’ and go to Software Update.
(3) Check Server IP and File name whether it is correct to download. If it is wrong,
select Server IP and File name and press ‘ENTER’ button to input new information
by Text input Dialog box.
Make sure the information of Server IP & File name through your supplier.
(4) Select ‘UPDATE’ and press ‘ENTER’ button to proceed with Software upgrade.
(5) After completing upgrade, the system will reboot automatically.
(6) Then, Check S/W version by press INFO button
1-7. SETUP DATA
KPD-M series supply users with another convenient function. In case users have to setup
the menus of several DVR in the same modes, SETUP DATA function reduce the repeated
labor by backing up and restoring the menu setup through USB.
BACKUP SETUP DATA
Connect USB-Memory and
Press ENTER to continue
[ENTER]->YES, [MENU]->NO
1-7-1. BACKUP SETUP DATA
Users can backup the current menu setup for
the other DVR menu setup.
RESTORE SETUP DATA
Connect USB-Memory and
Press ENTER to continue
[ENTER]->YES, [MENU]->NO
1-7-2. RESTORE SETUP DATA
Users can restore the backed-up menu setup for
the other DVR menu setup.
1-7-3. DEFAULT SETUP
27
OPERATION
Press ‘ENTER’ button to initialize the system in default setup mode.
2. DISPLAY
2-1. SEQUENCE DWELL(SINGLE)
(1) In Sequence dwell menu, select desired
Camera by using ▲▼ button and press
ENTER button.
[S.DWELL(SINGLE)]
CH SEC CH SEC
01 ▷02 09 ▷02
02 ▷02 10 ▷02
……… ……….
(2) Input desired second by using number button
and press ‘ENTER’ button to finish the setting.
……… ……….
04 ▷02 16 ▷02
Maximum time is up to 60
seconds.
If you want to cancel, press ‘MENU’ button.
[S.DWELL(GROUP)]
NO SEC
[CAMERA NAME]
NO NAME NO NAME
01 CH 01 09 CH 09
02 CH 02 10 CH 10
03 CH 03 11 CH 11
........ …….
……. …….
08 CH 08 16 CH 16
2-2. SEQUENCE DWELL(GROUP)
* KPD-M901 / M1601
01 ▷03
02 ▷03
(1) In Sequence dwell menu, select desired quad no. by
using ▲▼ button and press ‘ENTER’ button.
03 ▷03
04 ▷03
(2) Input desired second by using number button and press ‘ENTER’ button to finish
the setting.
Can enter maximum up to 60 seconds
If you want to cancel, press ‘MENU’ button.
[KPD-M901] [KPD-M1601]
2-3. CAMERA NAME
(1) Select desired camera by using ▲▼ button
and press ‘ENTER’ button.
(2) TEXT INPUT DIALOG window will appear.
(3) Enter desired camera name and press
‘MENU’ button to finish input
Group No. Camera
1 Channel 1 ~ Channel 4
2 Channel 5 ~ Channel 8
3 Channel 6 ~ Channel 9
Group No. Camera
1 Channel 1 ~ Channel 4
2 Channel 5 ~ Channel 8
3 Channel 9 ~ Channel 12
4 Channel 13~ Channel 16
28
OPERATION
2-4. CAMERA STATUS
[CAMERA STATUS]
(1) Select the camera and press ‘ENTER’ button
in Camera status mode.
NO STATUS
01 ▷SHOW 09 ▷SHOW
02 ▷SHOW 10 ▷SHOW
03 ▷SHOW 11 ▷SHOW
04 ▷SHOW 12 ▷SHOW
[STATUS]
(2) Select desire sub-item and press ‘ENTER’
button.
SHOW
HIDE
……. ……..
……. ……..
SHOW : Display the camera on monitor
08 ▷SHOW 16 ▷SHOW
HIDE : Not display the camera on monitor
Even if a camera is set in hide mode, the camera actually is recorded.
Hidden camera won’t be displayed on playback mode also.
2-5. CAMERA COLOR
(1) Select a desired camera by direction button and press ‘ENTER’ button
(2) Select desired item and Press ◀▶ button to ‘ENTER’ the value.
CHANNEL 1
BRIGHT : 0
◀ button :
－ (decrease value): -125
CONTRAST : 0
COLOR : 0
▶ button :
+ (increase value) : -125
DEFAULT
-:< + : >
(3) Press ‘ENTER’ button to finish the setting. (‘MENU’ button : Cancel the setting)
[SPOT DWELL (SINGLE)]
CH SEC CH SEC
01 ▷02 09 ▷02
02 ▷02 10 ▷02
……… ……….
……… ……….
04 ▷02 16 ▷02
[CAMERA COLOR] [CAMERA COLOR]
CH COLOR CH COLOR CH COLOR CH COLOR
01 ▷DEFAULT 09 ▷DEFAULT 01 ▷ADJUST 09 ▷DEFAULT
02 ▷DEFAULT 10 ▷DEFAULT 02 ▷DEFAULT 10 ▷DEFAULT
03 ▷DEFAULT 11 ▷DEFAULT 03 ▷DEFAULT 11 ▷DEFAULT
08 ▷DEFAULT 16 ▷DEFAULT 08 ▷DEFAULT 16 ▷DEFAULT
* KPD-M901 / M1601
2-6. SPOT DWELL(SINGLE)
(1) Select desired Camera by using ▲▼ button
and press ENTER button.
(2) Input desired second by using number button
and press ‘ENTER’ button to finish the setting.
Can enter maximum up to 60 seconds.
If you want to cancel, press ‘MENU’ button.
29
OPERATION
* KPD-M901 / M1601
2-7. SPOT DWELL(GROUP)
[SPOT.DWELL(GROUP)]
NO SEC
(1) Select desired Camera by using ▲▼ button and press
‘ENTER’ button.
01 ▷02
02 ▷02
03 ▷02
(2) Input desired second by using number button and press
‘ENTER’ button to finish the setting.
04 ▷02
Can enter maximum up to 60 seconds
If you want to cancel, press ‘MENU’ button.
[CHANGE VGA FREQ]
- 60HZ
[CHANGE VGA FREQ]
- 60HZ
- 50HZ
[VIDEO STANDARD]
▷AUTO DETECTION
▷SWITCH
▷NTSC
▷PAL
[KPD-M901] [KPD-M1601]
2-8. VGA FREQUENCY CHANGE
(1) Press ‘ENTER’ button in Change VGA freq.
(2) Select desired video frequency.
2-9. VIDEO ST ANDARD
(1) Select your video system
AUTO DETECTION : Set video automatically.
SWITCH : Set video according to jumper on main board.
NTSC : Set video to NTSC system.
PAL : Set video to PAL system.
After changing Video standard, DVR system will reboot automatically
Group No. Camera
1 Channel 1 ~ Channel 4
2 Channel 5 ~ Channel 8
3 Channel 6 ~ Channel 9
Group No. Camera
1 Channel 1 ~ Channel 4
2 Channel 5 ~ Channel 8
3 Channel 9 ~ Channel 12
4 Channel 13~ Channel 16
30
OPERATION
3. REC
3-1. REC PROPERTY.
Select desired item and press ‘ENTER’ button to change value.
[SETUP-REC-PROPERTY]
REC RESOLUTION : ▷ 720X480
CH QUALITY RATE CH QUALITY RATE
01 ▷ HIGH ▷ 2 09 ▷ HIGH ▷ 2
02 ▷ HIGH ▷ 2 10 ▷ HIGH ▷ 2
03 ▷ HIGH ▷ 2 11 ▷ HIGH ▷ 2
……. ……
08 ▷- HIGH ▷ 2 16 ▷ HIGH ▷ 2
[REC CONTINUOUS]
- ON
- OFF
3-1-1. REC resolution
(1) Select desired resolution and press ‘ENTER’ button
RESOLUTION
- 720 X 480
- 720 X 240
- 320 X 240
3-1-2. Quality
QUALTY
- BEST
(1) Select desired quality and press ‘ENTER’ button
- HIGH
- NORMAL
- BASIC
3-1-3. Rate
(1) Select desire frame rate by ◀▶ button and press ‘ENTER’ button
(2) Non-available frame in each resolution mode will be indicated as Red color.
[FRAME RATE]
0 1 2 4 8 15 30
(3) Press ‘MENU’ button to save and go to previous mode.
3-2. REC OPTIONS
[REC OPTION]
RECORD CONTINUOUS : ▷OFF
PLAY DEINTERLACE ▷ON
WATER MARK ▷OFF
3-2-1. RECORD CONTINOUS
ON : DVR system will record always. Cannot stop
recording by manual operation.
OFF : DVR system will record in manual operation.
If REC-CONTINUOUS IS OFF, anybody can stop recording by record
stop button. So, recommended to set REC-CONTINUOUS mode to ON.
31
OPERATION
3-2-2. PLAY DEINTERLACE
[PLAY DEINTERLACE]
- ON
- OFF
When displaying playback recorded by 720X480
resolution through analog monitor, there can be flickering
of image. With this function, you can see smooth display.
3-2-3. WATER MARK
[WATER MARK]
- ON
With this function, users can protect recorded data not
to modify image. If there is any attempt to modify the
video, the video cannot be played.
- OFF
3-3. EVENT REC
[EVENT]
- MOTION DETECTION
- SENSOR DETECTION
- OPTIONS
3-3-1. MOTION DETECTION
[EVENT REC(M/D)]
NO SEN AREA NO SEN AREA
01 ▷0 ▷OFF 09 ▷0 ▷OFF
02 ▷0 ▷OFF 10 ▷0 ▷OFF
03 ▷0 ▷OFF 11 ▷0 ▷OFF
……. ……
08 ▷0 ▷OFF 16 ▷0 ▷OFF
SEN
1
2
3
4
5
(1) Select desired camera to set motion detection and press ‘ENTER’
button
- SEN : Adjust sensitivity of motion. Enter sensitivity value from 0
to 9 by number button.
Sensitivity rate : 0(Low) <1<2……<8<.9(High)
- AREA : Adjust the area of motion
[AREA]
.ALL : select all area
- ALL
- PART
.PART : Select desired area.
-
.OFF : Quit motion detection function.
32
OPERATION
[EVENT-OPTIONS]
POST-RECORD TIME : ▷ 10SEC
PRE-RECORD TIME : ▷ 4SEC
POP-UP SCREEN : ▷ ON
[PRE REC TIME]
- NO PRE REC
- 2SEC
- 4SEC
- 6SEC
- 8SEC
- 10SEC
CH1
Motion detection area
Non motion detection
If you select ‘part’ of specific camera, the screen
will change to set like side picture. Select desire area
with direction button and press ‘ENTER’ button to
select area. To cancel the selected block, press
‘ENTER’ button one more.
3-3-2. SENSOR DETECTION
Select desire position and press ‘ENTER’ button.
z ■ : Sensor detection ON
z □ : Sensor detection OFF
[EVENT REC(S/D)]
1
3-3-3. OPTIONS
Set recording options when event happens.
3-3-3-1. POST-RECORD TI ME
; Set recording time after Event occurs
3-3-3-2. PRE RECORD TIME
; Set recording time before Event occurs
CH 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6
S 01
□□□□□□■□□□□□□□□□
S 02
□□□□□□■□□□■□□□□□
S 03 □□□□□□■□□□■□□□□□
S 04 □□□□□□■□□□□□□□□□
Camera No.
Example)
If Sensor No.2&3 is detected,
Sensor No.
camera No. 11 is recorded.
ALL □□□□□□■□□□□□□□□□
[POST REC TIME]
- 10SEC
- 30SEC
- 1 MIN
- 5 MIN
- 10MIN
33
OPERATION
3-3-3-3. POP UP
ON : When event happens in specific camera, the camera will be popped up.
OFF : The popup function is off.
[POP UP SCREEN]
- ON
- OFF
3-4. SCHEDULE REC
Users can set up the schedule recording on desired channel, date and time.
(1) Select desired camera to record by schedule and press ‘ENTER’ button.
[SCHEDULE REC]
CH
01
02
03
04
ALL
(2) Select desire position for a day of week & time and press ‘ENTER’ button
Example) System will record from 06:00 to 07:00 in
whole week.
z ■ : RECORDING
[SCHEDULE: CH-1]
SUN
MON
TUE
WED
THU
FRI
SAT
ALL
DAY
1 2
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3
□□□□□□■□□□□□□□□□□□□□□□□□
□□□□□□■□□□□□□□□□□□□□□□□□
□□□□□□■□□□■■■■□□□□□□□□□□
□□□□□□■□□□□□□□□□□□□□□□□□
□□□□□□■□□□□□□□□□□□□□□□□□
□□□□□□■□□□□□□□□□□□□□□□□□
□□□□□□■□□□□□□□□□□□□□□□□□
□□□□□□■□□□□□□□□□□□□□□□□□
If you select specific time of “ALL DAY”, the specific time
of whole week will be marked.
z
□ : NOT RECORDING
Example) System will record from 10:00 to 14:00 on Tuesday
34
OPERATION
3-5. DELETE REC
(1) Select desired data clip and press ‘ENTER’ button.
(2) New window announcing WARNING will appear.
(3) Press ‘ENTER’ button to delete selected data clip. (‘MENU’ button : cancel)
[WARNING!!!]
ALL RECORDED FILE
WILL BE DELETED
ARE YOU SURE?
[‘ENTER’] -> YES [‘MENU’] -> NO
FILE LIST – DELETE 1/105
0338 20050806_125000 600S D L W
0338 20050806_125000 600S D U W
0338 20050806_125000 600S D U W
0338 20050806_125000 600S D U W
[WARNING!!!]
0338 20050806_125000 600S D U W
DELETE FILE
0338 20050806_125000 600S D U W
0338 20050806_125000 600S D U
0338 20050806_125000 600S D U W
0338 20050806_125000 600S D U W
ARE YOU SURE?
0338 20050806_125000 600S D U W
[‘ENTER’]→YES [‘MENU’]→NO
0338 20050806_125000 600S D U W
PGUP:〈 PGDN: 〉 LAST:《 FIRST: 》
3-6. LOCK / UNLOCK REC
You can preserve some desired data with this function. The locked data will
be marked to
‘L’ and will not be erased on overwriting of HDD.
(1) Select desired file to protect and press ‘ENTER’ button.
FILE - LOCK/UNLOCK 1/105
0338 20050806_125000 600S D U W
0338 20050806_125000 600S D U W
0338 20050806_125000 600S D U W
0338 20050806_125000 600S D U W
0338 20050806_125000 600S D U W
3-7. DELETE ALL RE C
(1) Press ‘ENTER’ button to delete all data (‘MENU’ button : Cancel)
You can’t delete files while recording. Please stop recording if you delete files.
0338 20050806_125000 600S D L W
0338 20050806_125000 600S D U W
Protected file
0338 20050806_125000 600S D U W
0338 20050806_125000 600S D U W
0338 20050806_125000 600S D U W
PGUP:〈 PGDN: 〉 LAST:《 FIRST: 》
35
OPERATION
4. NETWORK
4-1. NETWORK TYPE
NETWORK TYPE
(1) Select network type according to your network
system.
STATIC
DYNAMIC
PPPOE
z STATIC : Static IP
z DYNAMIC : Dynamic IP
z PPPOE : when your system is connected to ADSL modem
(2) STATIC IP
[STATIC IP]
1) Enter IP ADDRESS / GATEWAY / SUB-
NETMASK by using number key
IP ADDRESS
XXX.XXX.XXX.XXX
GATEWAY
2) Press ‘ENTER’ button to save.
XXX.XXX.XXX.XXX
SUB-NETMASK
XXX.XXX.XXX.XXX
(3) DYNAMIC IP
[DYNAMIC IP]
IP ADDRESS
1) If you select Dynamic IP, system will
detect IP address automatically and show
IP information.
XXX.XXX.XXX.XXX
GATEWAY
XXX.XXX.XXX.XXX
SUB-NETMASK
XXX.XXX.XXX.XXX
(4) PPPOE (for ADSL)
[PPPOE]
NAME : XXXX
AUTH : XXXXX
; If your network system is ADSL, you need to
enter your ID (NAME) and password (AUTH) to
access Internet. If you don’t know your ID &
Password, please ask your ISP supplier of your ID & Password.
36
OPERATION
4-2. DDNS
z This is for user who is using dynamic IP. With this function, user can use
dynamic IP like static IP
Example)
4-3. NET PASSWORD
(1) Enter new NET Password to change by Number button.
(2) Enter new NET Password again to confirm the Password.
4-4. NET CLIENT PORT
(1) Press ‘ENTER’ button in net client port mode.
(2) Select desire port rate and press ‘ENTER’ button
(3) Press ‘MENU’ button
ACTIVATE
NO
videonet.co.kr
[DDNS]
DOMAIN :
USER ID :
GROUP ID :
PASSWORD :
ACTIVATE : <- NO>
[PASSWORD]
‘ENTER’ NEW NETWORK PASSWORD
: _ _ _ _
[PASSWORD]
CONFIRM NEW NETWORK PASSWORD
: _ _ _ _
[CLIENT PORT]
PORT AREA : ▷7620-7624
PORT1(LOGON) : 07620
PORT2(CONTROL) : 07621
PORT3(LIVE) 07622
PORT4(PLAY) 07623
POR51
(
BACKUP) : 07624
PORT AREA
-7620-7624
-7630-7634
-7640-7644
-7650-7654
-7660-7664
Domain : input your domain name of DDNS website
User ID : input your ID of DDNS web site
Group ID : input your group ID of DDNS web site
P ASSWORD : input password of DDNS web site
Activate : Select website that you registered to
activate DDNS function.
z This system supports two website at
www.dyndns.org and www.ipupdater.com
z For details, please refer network manual.
[DDNS]
DOMAIN : kpro.dyndns.org
USER ID : kpro
GROUP ID : XXXXX
PASSWORD : 1234
ACTIVATE : videonet.co.kr
37
OPERATION
4-5. NET CLIENT ID
[CLIENT ID]
(1) Press ‘ENTER’ button to input ID & Password
in net client ID mode.
LOGIN-ID : PASSWORD
1 :
2 :
(2) Enter name by TEXT INPUT DIALOG and
press ‘MENU’ button when you finish.
3 :
4 :
4-6. NET DVR ID
(1) Press ‘ENTER’ button to input ID in net DVR ID
mode.
[DVR ID]
ID:
(2) Enter name by TEXT INPUT DIALOG and press ‘MENU’ button to save.
This function is for system check when network connection.
It’s not necessary to set this menu for network connection.
4-7. NET CLIENT ADDR
[CLIENT IP]
CLIENT IP 01: 000.000.000.000
z Enter IP address by using number key to register IP
address that can access to the system.
CLIENT IP 02 : 000.000.000.000
CLIENT IP 03: 000.000.000.000
CLIENT IP 04: 000.000.000.000
CLIENT IP 05: 000.000.000.000
CLIENT IP 06: 000.000.000.000
CLIENT IP 07: 000.000.000.000
Can register maximum 10 IP address to access
the system.
CLIENT IP 08: 000.000.000.000
CLIENT IP 09: 000.000.000.000
CLIENT IP 10: 000.000.000.000
4-8. NETWORK THROUGHTPUT
[NETWORK-THROUGHT]
THROUGHPUT : ▷UNLIMITED
(1) Press ‘ENTER’ button.
[THROUGHPUT]
(2) Then, sub-menu will appear.
UNLIMITED
64K
(3) Select desire speed rate and press ‘ENTER’ button.
128 K
256 K
512 K
1 M
2 M
4 M
10 M
4-9. WEB PORT
When remote-access with Web-browser, default web-port is port # 80, but you can assign
you own specific web-port, such as port 8080 or 1080, as an Web port.
Enter Number (0000~9999)
0000
38
OPERATION
5. SENSOR / SOUND
5-1. SENSOR TYPE
(1) Select connected sensor No. and press ‘ENTER’ button.
(2) Select Sensor type and press ‘ENTER’ button.
.
5-2. ALARM MOTION MANAGER
; If camera detects motion, designated alarm will output.
(1) Select Camera no & Alarm no and press ‘ENTER’ button.
(2) Press ‘MENU’ button to save.
5-3. ALARM SENSOR MANAGER
; If sensor is detected, designated alarm will output.
(1) Select Sensor no & Alarm no and press ‘ENTER’ button
(2) Press ‘MENU’ button to save
[SENSOR MANAGER]
1
SENSOR NO
1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6
ALARM 1
□□□□□□□□□□□□□□□□
ALARM 2
□□□□□□□□□□■□□□□□
ALARM 3
□□□□□□□□□□■□□□□□
ALARM 4 □□□□□□□□□□□□□□□□
ALL ALARM
□□□□□□□□□□□□□□□□
[MOTION MANAGER]
1
CHANNEL
1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6
ALARM 1
□□□□□□□□□□□□□□□□
ALARM 2
□□□□□□□□□□■□□□□□
ALARM 3
□□□□□□□□□□■□□□□□
ALARM 4 □□□□□□□□□□□□□□□□
ALL ALARM
□□□□□□□□□□□□□□□□
[SENSOR TYPE]
TYPE
SENSOR 1 ▷NO SENSOR 9 ▷NO
NC
SENSOR 2 ▷NO SENSOR10 ▷NO
NO
SENSOR 3 ▷NO SENSOR11 ▷NO
.....................
SENSOR 8 ▷NO SENSOR16 ▷NO
If Motion is detected at Camera
No.11, Alarm No 2,3 will output
■ : Alarm out ON
□ : Alarm out OFF
z
■ : Alarm out ON
z □ : Alarm out OFF
If Sensor No.11 is detected,
Alarm No 2,3 will output
39
OPERATION
5-4. ALARM BUZZER
ON : Alarm buzzer is working when sensor signal is detected.
OFF : Buzzer OFF.
[BUZZER OUTPUT]
- ON
- OFF
5-5. ALARM OUTPUT
(1) Select desire Alarm no and press ‘ENTER’ button
(2) Select ON or OFF and press ‘ENTER’ button
[ALARM OUTPUT]
ALARM 1 ▷ OFF ALARM 3 ▷ ON
ALARM 2
▷
ON ALARM 4 ▷ON
[ALARM OUTPUT]
ON
OFF
5-6. ALARM OUT PERIOD
(1) Press ‘ENTER’ button in Alarm out period mode..
[ALARM OUT PERIOD]
(2) Select desire period of alarm out and press
‘ENTER’ button
30 SEC
01 MIN
03 MIN
10 MIN
CONTINUOUS
* KPD-M901/M1601
5-7. AUDIO
Select the channel connected to audio and press ‘ENTER’ button.
[AUDIO]
Audio1 Æ Channel 1
1
Audio2 Æ Channel 2
CHANNEL
1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6
Audio3 Æ Channel 3
AUDIO 1
■□□□□□□□□□□□□□□□
Audio4 Æ Channel 4
AUDIO 2 □■□□□□□□□□□□□□□□
AUDIO 3
□□■□□□□□□□□□□□□□
AUDIO 4 □□□■□□□□□□□□□□□□
40
HDD INSTALLATION
1. Unscrew the top cover of DVR.
2. Assemble hard disks and HDD bracket the same
as the picture. Please be noted that that bracket has
front and rear. You must put HDD in right direction.
3. Install the HDDs assembled in the bracket at
the designated spot.
The cables connected to the front board
should be under the HDD bracket.
4. Connect the HDDs to mainboard with gray cable. The
connector outside the mainboard is for HDD.
Before installing the Hard Disk Drives, please read
the jumper setting information on the label. If the
jumper is not set properly, the system will be
disordered.
5. Make sure that the HDDs are set to “Master” & “Slave”
properly and cover the top.
* Check if HDD has no problem after HDD installation
because record function may not work well due to HDD
problem.
* It may reboot automatically when HDD has problems or it
doesn’t detect HDD.
* Contact your local distributor and exchange with new one
when you find your HDD has a problem.
41
TROUBLE SHOOTING
In the event of a product malfunction, please check the list below for a possible solution before
requesting service.
Problem Explanation / Solution
9 Check that the power plug is connected to a wall
outlet and a SMPS
Power
No power
9 Check the video input / output connections on the
product rear panel
No Video or the Video is
back screen
9 Check the camera / the camera video/power
cable connections
9 Check if Camera status in menu is SHOW
Æ Refer to Page 18
Video
Not display camera name 9 Camera name is shown only in full screen mode.
No Audio but Video is
O.K during monitoring
9 Check the audio input / output connections on the
product rear panel
/
Audio
9 Audio works only in full screen mode
No Audio but Video is
O.K during playback
Can’t stop recording by
remote controller
9 Check RECORD CONTINUOUS of REC OPTION
of MENU is OFF
Playback
Can’t find previous
recording data
9 The product operates automatically OVERWRITE
function. It deletes previous recording data to
overwrite when HDD is full.
9 Please check if USB memory stick has
protection(Password) function. USB memory
stick should not have protection function.
Not compatible with USB
memory stick
Backup
9 Check if network of menu is setting correctly
Can’t connect by network 9 Check if your internet line is available. Please ask
your service provider to check internet line
Network
If the problem you are experiencing persists or is not mentioned above, please contact service
center or your local distributor.
42
Loading...