Protech 2004 User Manual

PROTECH

Automatic Mixing with Dugan Speech System.

*

4/8 Mic/Line Inputs With Selectable Gain Structures.

*

Phantom Power Capability On Each Input

*

Clip Indicator For All Inputs

*

Assignable Group Mute Per Input

*

12 Segment LED Metering of Output Level

*

Remote Gain Control Capability On Master Output.

*

Linkable for More Inputs

*

U.S. Patents 3,992,584, & 4,864,627

*

1/06

®

INSTALLATION & OPERATION MANUAL

MODELS 2004 & 2008

DUGAN AUTOMATIC MIXERS

The Protech Audio Models 2004.2008 Automatic Micro­phone Mixers are designed to be the best operating, most
transparent auto-mixers, for rental and portable applica­tions as well as small venues. Both the 2004 and 2008
feature patented adaptive proportional gain sharing
control circuitry designed by Dan Dugan, the inventor
of automatic mixing. This operating system results in the
best, most transparent automatic mixing to be found
anywhere. Unlike gated mixers, or quasi-Dugan mixers,
the 2004 and 2008 operate on an elegantly simple prin­ciple; each individual input channel is attenuated by an
amount, in dB, equal to the difference, in dB, between that
channel's level and the sum of all channel levels. The levels
are varied on a continuous basis, with no on-off actions, or
abrupt gain changes.
The 2008 features 8 switchable microphone/line level
inputs. The model 2004 features 4 similar inputs. Two
units may be linked together to create up to 16 inputs.
Both units feature a unique works-in-a-drawer construc­t ion . Access t o a l l sw itches and push-on jumpers used
to configure various features, is achieved by loosening
the two thumbscrews located on each side of the front
panel, and sliding the entire electronics out of the chassis.
This easy access allows complete reconfiguration in just
minutes.
In addition to the input mode (mic/line) switch located at
each input, the gain of each input is configurable, via a
push-on jumper, to allow superior signal-to-noise opera-

tion. Moving the jumper over one pin changes the input
gain from 30dB to 50dB.
A bi-color LED is used to indicate signal presence and clip
threshold. Unlike other units, the clip indicator on the
Model 2008 indicates clipping of the summing buss, not
just an input, since it is possible to clip a summing bus,
without clipping an input.
Internal 15 volt phantom power is selected, on a channel­by-channel basis, via a push-on jumper. When the input
mode slide switch is placed in the line position,
phantompower will automatically be disconnected, pre­venting damage to line level devices.
The Models 2004 and 2008 also feature assignable group
mute function. Each input may be assigned to the mute
buss via an eight position DIP switch. Turning on a given
switch will assign that channel to the group mute.
Grounding the group mute control pin will mute the as­signed channels.
The output level of the automixers may be controlled via
the front panel output potentiometer, or, assigned to a
remote potentiometer, via an on-board slide switch.
Both units have been designed with the operator in mind.
Control features allow the operator to attend to other
functions, without the need to continuously "ride gain".
For additional information on the model 2004 and 2008, or
the Models 2000 Boardroom Automixer, and 2000-C Court­room Automixer, contact: Applications Assistance

IOM2008.PM6

www.protechaudio.com

Protech Audio Corporation, PO Box 597, 192 Cedar River Road, Indian Lake, New York, 12842, Voice 518-648-6410 Fax [phone]

INSTALLATION

GROUP MUTE

The Model (2004 or 2008) has been shipped from the
factory with all inputs set for microphone level operation,
and the internal 15 volt phantom power enabled on each
input.
If line level operation is required on some inputs, the
following steps are required.
Mount the Model (2004/2008) in a suitable rack.

UNPLUGGING THE ELECTRONICS

Loosen the two thumbscrews, located on each side of the
front panel (see page 3) half-way.
Unplug the electronic section from the chassis.
Set the appropriate input mode switches (see page 3) to
line level. Doing so will automatically disconnect the phan­tom power.
Set the appropriate group mute switch position(s) to "ON"
(see page 3).
Slide the electronics section back into the chassis.
Place forefingers on the top of the front panel, and thumbs
on bottom of front panel. Apply slight pressure with thumbs
to raise rear of electronics section, until it seats properly
into chassis connectors. Push electronics section in until
front panel is flush with mounting ears.
Tighten thumbscrews.
Wire inputs and outputs using two-conductor shielded
cable.

The 4/8 position DIP (see page 3) switch assigns individual
inputs to the group mute bus. Grounding the group mute
screw, on the rear barrier strip, activates the group mute. All
screw connections labeled "SH", are ground.
Linked chassis's will operate on the master chassis group
mute screw terminal.

LINKING

Two pieces of the Model (2004/2008) may be linked to­gether, to provide up to 16 inputs, to a common output.
There is a Master/Slave switch on the electronic section PC
assembly (see page 3). Follow the instructions for unplug­ging the electronics.
Set the Master/Slave slide switch, on the unit to be desig­nated "Slave", to the slave position.
Plug the electronics section back into the chassis.
Wire the 6 "LINK" connections as shown on page 3.
Raising or lowering the output pot, on the unit designated
"Master", will now control all 16 inputs channels.

ALIGNMENT

REMOTE LEVEL CONTROL

Follow the instructions for unplugging the electronics.
Set the slide switch labeled "REM VOL", to the "ON"
position.
Plug the electronics section back into the chassis.
Wire the 3 "REMOTE CONTROL" connections as shown
on page 3.
Raising or lowering the remote pot, will now control the
output level.

GROUND LIFT SWITCH

Normally set to the "GND ON" position.

PHANTOM POWER

One push-on red jumper for each input. See page 3 for
locations. Set input mode switch to "LINE" position auto­matically disconnects phantom power from that input.

Set the output pot to 3:00 position.

While someone speaks into each microphone, adjust the
corresponding input pot until the desired output level is
achieved. Repeat for each input.

If high output level microphones (Condenser Mics) are to be
used, it may be desirous to lower the input preamplifier
stage to 30dB of gain. See page 3 for location of push-on
jumpers for each input channel.

The Signal Presence/Clip indicator turns green when the
input summing bus reaches -15dB, and turns red when the
bus reaches +15dB.

The alignment is now completed. The Model (2004/2008)
will ride gain on each input, in similar fashion to an experi­enced sound system operator, but much faster.

Page 2

6/01