ProStar M540V User Manual
I
Preface
Notice
The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or
inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage
resulting from the use (or misuse) of this publication.
This publication and any accompanying software may not, in whole or in part, be reproduced, translated,
transmitted or reduced to any machine readable form without prior consent from the vendor, manufacturer
or creators of this publication, except for copies kept by the user for backup purposes.
Brand and product names mentioned in this publication may or may not be copyrights and/or registered
trademarks of their respective companies. They are mentioned for identification purposes only and are not
intended as an endorsement of that product or its manufacturer.
©July 2005
Trademarks
This product incorporates copyright protection technology that is protected by method claims of certain
U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights
owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and
is intended for home or other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.
Intel®, Pentium® and Celeron® are US registered trademarks of Intel Corporation.
II
Preface
FCC Statement
(Federal Communications Commission)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
• Re orient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the service representative or an experienced radio/TV technician for help.
Warning
Use only shielded cables to connect I/O devices to this equipment. You are cautioned that changes or modifications not expressly approved by the manufacturer for compliance with the above standards could void your authority to operate the equipment.
III
Preface
IMPORTANT SAFETY INSTRUCTIONS
Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and
injury to persons when using any electrical equipment:
1. Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub,
in a wet basement or near a swimming pool.
2. Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm.
There may be a remote risk of electrical shock from lightning.
3. Do not use the telephone to report a gas leak in the vicinity of the leak.
4. Use only the power cord and b atteries indicated in this manual. Do not d ispose of batterie s in a fire. They
may explode. Check with local codes for possible special disposal instructions.
5. This product is intende d to be supplied by a Listed Power Unit (DC Output 20V, 3.25A (65W) minimum
AC/DC Adapter, OR by a DC Output 20V, 4.5A (90W) minimum AC/DC Adapter if you are using the
optional port replicator- see pages 7 - 14 & C - 5).
CAUTION
Always disconnect all telephone lines from the wall outlet before servicing or disassembling this equipment.
TO REDUCE THE RISK OF FIRE, USE ONLY NO. 26 AWG OR LARGER,
TELECOMMUNICATION LINE CORD
This Computer’s Optical Device is a Laser Class I Product
IV
Preface
Instructions for Care and Operation
The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions:
1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged.
2. Keep it dry, and don’t overheat it. Keep the computer and power supply away from any kind of heating
element. This is an electrical appliance. If water or any other liquid gets into it, the computer could be
badly damaged.
Do not expose the computer
to any shock or vibration.
Do not place it on an unstable
surface.
Do not place anything heavy
on the computer.
Do not expose it to excessive
heat or direct sunlight.
Do not leave it in a place
where foreign matter or moisture may affect the system.
Don’t use or store the computer in a humid environment.
Do not place the computer on
any surface that will block the
Vents/Fan Intakes.
V
Preface
3. A void interference. Keep the computer away from high capacity transformers, electric motors, and other
strong magnetic fields. These can hinder proper performance and damage your data.
4. Follow the proper working pro ced ures fo r the compute r. Shut the computer down properly and don’t
forget to save your work. Remember to periodically save your data as data may be lost if the battery is
depleted.
5. Take care when using peripheral devices.
Do not turn off the power
until you properly shut down
all programs.
Do not turn off any peripheral
devices when the computer is
on.
Do not disassemble the computer by yourself.
Perform routine maintenance
on your computer.
Use only approved brands of
peripherals.
Unplug the power cord befor e
attaching peripheral devices.
VI
Preface
Power Safety
The computer has specific power requirements:
• Only use a power adapter approved for use with this computer.
• Your AC/DC adapter may be designed for international travel but it still requires a
steady, uninterrupted power supply. If you are unsure of your local power specifications, consult your service representative or local power company.
• The power adapter may have either a 2-prong or a 3-prong grounded plug. The
third prong is an important safety feature; do not defeat its purpose. If you do not
have access to a compatible outlet, have a qualified electrician install one.
• When you want to unplug the power c ord, be sure to disconnect it by the plug head,
not by its wire.
• Make sure the socket and any extension cord(s) you use can support the total current load of all the connected devices.
• Before cleaning the computer, make sure it is disconnected from any external
power supplies (i.e. AC/DC adapter or car adapter).
Do not plug in the power
cord if you are wet.
Do not use the power cord if
it is broken.
Do not place heavy objects
on the power cord.
Power Safety
Warning
Before you undertake
any upgrade procedures, make sure that
you have turned off the
power, and disconnected all peripherals
and cables (including
telephone lines). It is
advisable to also remove your battery in
order to prevent accidentally turning the
machine on.
VII
Preface
Battery Precautions
• Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer.
• Do not remove any batteries from the computer while it is powered on.
• Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any
way. Even if the computer continues to work with a damaged battery in place, it may cause circuit damage,
which may possibly result in fire.
• Recharge the batteries using the notebook’s system. Incorrect recharging may make the battery explode.
• Do not try to repair a battery pack. Refer any battery pack repair or replacement to your service representative
or qualified service personnel.
• Keep children away from, and promptly dispose of a damaged battery. Always dispose of batteries carefully.
Batteries may explode or leak if exposed to fire, or improperly handled or discarded.
• Keep the battery away from metal appliances.
• Affix tape to the battery contacts before disposing of the batt ery.
• Do not touch the battery contacts with your hands or metal objects.
Battery Disposal & Caution
The product that you have purchased contains a rechargeable battery. The battery is recyclable. At the end of its
useful life, under various state and local laws, it may be illegal to disp ose of thi s battery into the municip al w aste
stream. Check with your local solid waste officials for details in your area for recycling options or proper disposal.
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended
by the manufacturer. Discard used battery according to the manufacturer’s instructions .
VIII
Preface
Cleaning
Do not apply cleaner directly to the computer; use a soft clean cloth.
Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer.
Servicing
Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and
the computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer
from the power supply. Then refer servicing to qualified service personnel under any of the following conditions:
• When the power cord or AC/DC adapter is damaged or frayed.
• If the computer has been exposed to rain or other liquids.
• If the computer does not work normally when you follow the operating instructions.
• If the computer has been dropped or damaged (do not touch the poisonous liquid if the LCD pan el breaks).
• If there is an unusual odor, heat or smoke coming from your computer.
Removal Warning
When removing any cover(s) and screw(s) for the purposes of device upgrade, remember to replace the cover(s)
and screw(s) before turning the computer on.
IX
Preface
Travel Considerations
Packing
As you get ready for your trip, run through this list to make sure the system is ready to go:
1. Check that the battery pack and any spares are fully charged.
2. Power off the computer and peripherals.
3. Close the display panel and make sure it’s latched.
4. Disconnect the AC/DC adapter and cables. Stow them in the carrying bag.
5. The AC/DC adapter uses voltages from 100 to 240 volts so you won’t need a second voltage adapter.
However, check with your travel agent to see if you need any socket adapters.
6. Put the notebook in its carrying bag and secure it with the bag’s straps.
7. If you’re taking any peripherals (e.g. a printer , mouse or digital camera), pack them and those devices’
adapters and/or cables.
8. Anticipate customs - Some jurisdictions may have import restrictions or require proof of ownership for
both hardware and software. Make sure your “papers” are handy.
Power Off Before Traveling
Make sure that your notebook is completely powered off before putting it into a travel bag (or any such container).
Putting a notebook which is powered on in a travel bag may cause the Vents/Fan Intakes to be blocked. To prevent your computer from overheating make sure nothing blocks the Vent/Fan Inta kes while the computer is in
use.
X
Preface
On the Road
In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting, keep these points in mind:
Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is
very common. Don’t check it with “normal” luggage. Baggage handlers may not be sufficiently careful.
Avoid knocking the computer against hard objects.
Beware of Electromagnetic fields - Devices such as metal detectors & X-ray machines can damage the
computer, hard disk, floppy disks, and other media. They may also destroy any stored data - Pass your
computer and disks around the devices. Ask security officials to hand-inspect them (you may be asked to
turn it on). Note: Some airports also scan luggage with these devices.
Fly safely - Most airlines have regulations about the use of computers and other electronic devices in
flight. These restrictions are for your safety, follow them. If you stow the notebook in an overhead compartment, make sure it’s secure. Contents may shift and/or fall out when the compartment is opened.
Get power where you can - If an electrical outlet is available, use the AC/DC adapter and keep your battery(ies) charged.
Keep it dry - If you move quickly from a cold to a warm location, water vapor can condense inside the
computer. Wait a few minutes before turning it on so that any moisture can evaporate.
XI
Preface
Developing Good Work Habits
Developing good work habits is important if you need to work in front of the computer for long periods
of time. Improper work habits can result in discomfort or serious injury from repetitive strain to your
hands, wrists or other joints. The following are some tips to reduce the strain:
• Adjust the height of the chair and/or desk so that the keyboard is at or slightly
below the level of your elbow. Keep your forearms, wrists, and hands in a relaxed
position.
• Your knees should be slightly higher than your hips. Place your feet flat on the
floor or on a footrest if necessary.
• Use a chair with a back and adjust it to support your lower back comfortably.
• Sit straight so that your knees, hips and elbows form approximat ely 90-degree
angles when you are working.
• Take periodic breaks if you are using the computer for long periods of time.
Remember to:
• Alter your posture frequently.
• Stretch and exercise your body several times a day.
• Take periodic breaks when you work at the computer for long periods of time. Frequent and short breaks are better than fewer and longer breaks.
XII
Preface
Lighting
Proper lighting and comfortable display viewing angle can reduce eye strain and muscle fatigue in your
neck and shoulders.
• Position the display to avoid glare or reflections from overhead lighting or outside sources of light.
• Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen
clearly.
• Position the display directly in front of you at a comfortable viewing distance.
• Adjust the display-viewing angle to find the best position.
XIII
Preface
Contents
Notice ...........................................................................I
FCC Statement .......................................................II
Instructions for Care and Operation .....................IV
Power Safety ..................................................... ...VI
Battery Precautions .............................................VII
Cleaning ............................................................ VIII
Servicing ........................................................... VIII
Travel Considerations ..........................................IX
Quick Start Guide
Overview ..................................................................1-1
Model Differences ..................................................1-2
Advanced Users .....................................................1-4
Beginners and Not-So-Advanced Users .................1-4
Warning Boxes .......................................................1-4
Not Included ...........................................................1-5
System Software .....................................................1-5
System Startup ..........................................................1-6
System Map: Model A -
Top View with LCD Panel Open .............................1-7
System Map: Model B -
Top View with LCD Panel Open .............................1-8
LED Indicators .........................................................1-9
Hot-Key Buttons & Keyboard ............................... 1-10
Function Keys ........................................................ 1-11
System Map: Front & Rear Views ......................... 1-12
System Map: Left View .........................................1-13
System Map: Right View ....................................... 1-14
System Map: Bottom View ....................................1-15
Windows XP Start Menu & Control Panel ............ 1-16
Video Features .......................................................1-17
Display Devices & Options .................................1-18
S3Tray Plus Utility ............................................. 1-18
Power Management Features ................................. 1-19
Features & Components
Overview ..................................................................2-1
Hard Disk Drive ....................................................... 2-2
Optical (CD/DVD) Device ...................................... 2-3
Loading Discs ........................................................ 2-3
Handling CDs or DVDs ......................................... 2-4
DVD Regional Codes ............................................ 2-5
4-in-1 Card Reader ................................................... 2-6
PC Card Slot ............................................................2-7
Inserting and Removing PC Cards ........................ 2-7
Auto Mail Checker ................................................... 2-8
XIV
Preface
Application Hot-Key .............................................. 2-10
TouchPad and Buttons/Mouse ...............................2-11
Configuring the TouchPad and Buttons ..............2-11
Audio Features .......................................................2-12
Adding a Printer .....................................................2-13
USB Printer .........................................................2-13
Parallel Printer .....................................................2-13
Power Management
Overview ..................................................................3-1
Advanced Configuration and Power Interface .......3-1
The Power Sources ............................................. .... ..3-2
AC/DC Adapter ......................................................3-2
Battery .................................................................... 3-2
Turning on the Computer .........................................3-3
Power Schemes ........................................................3-4
System Power Options .............................................3-6
Hibernate Mode vs. Shutdown ...............................3-6
Standby Mode vs. Hibernate Mode ........................3-6
Standby ..................................................................3-7
Hibernate ............................................................... 3-7
Configuring the Power Button .................................3-8
Battery Information ..................................................3-9
New Battery ..........................................................3-9
Battery Life ............................................. .... .... ......3-9
Recharging the Battery with the AC/DC Adapter 3-10
Proper handling of the Battery Pack ................... 3-11
Battery FAQ ........................................................ 3-12
Drivers & Utilities
What to Install ..........................................................4-1
Module Driver Installation .................................... 4-1
Service Packs .........................................................4-3
Authorized Driver Message ...................................4-4
Version Conflict Message ..................................... 4-4
Updating/Reinstalling Individual Drivers ............. 4-4
Driver Installation .................................................... 4-5
Driver Installation Procedure .................................4-7
Manual Driver Installation ................................... 4-7
Service Pack Installation ....................................... 4-7
New Hardware Found ............................................ 4-7
Chipset (WinXP) ..................................................4-8
Video (WinXP) ..................................................... 4-8
Audio (WinXP) .................................................... 4-8
LAN (WinXP) ......................................................4-8
Modem (WinXP) ..................................................4-9
TouchPad (WinXP) ..............................................4-9
PCMCIA/Card Reader (WinXP) ........................ 4-10
Hot-Key (WinXP) ..............................................4-10
AutoMail (WinXP) ............................................. 4-11
XV
Preface
Wireless LAN (WinXP) ......................................4-11
Bluetooth (WinXP) .............................................4-11
PC Camera (WinXP) ...........................................4-11
Port Replicator (WinXP) .....................................4-11
BIOS Utilities
Overview ..................................................................5-1
The Power-On Self Test (POST) .............................5-2
Failing the POST ....................................................5-3
Fatal Errors ............................................................5-3
Non-Fatal Errors ...................................................5-3
The Setup Program ...................................................5-4
Entering Setup ........................................................5-4
Setup Screens ................................... .... ..................5-5
Main Menu ...............................................................5-6
System Time & Date (Main Menu) ..........................5-6
Legacy Diskette A: ............................................. .... ..5-7
IDE Channel 0 Master/Slave (Main Menu) .............5-7
System/Extended Memory (Main Menu) .................5-7
Advanced Menu .......................................................5-8
Execute-Disable Bit Capability (Advanced Menu) ..5-8
Installed O/S: (Advanced Menu) ..............................5-9
Reset Configuration Data: (Advanced Menu) ..........5-9
Large Disk Access Mode: (Advanced Menu) ..........5-9
Legacy USB Support: (Advanced Menu) ................5-9
Intel On-Screen Branding Logo (Advanced Menu) 5-9
APIC interrupt routing: (Advanced Menu) ............ 5-10
PS/2 Mouse (Advanced Menu) .............................. 5-10
Local Bus IDE adapter: (Advanced Menu) ........... 5-10
OnChip USB /Audio /Modem /LAN Device:
(Advanced Menu) .................................................. 5-10
PC Beep: (Advanced Menu) .................................. 5-10
Security Menu ........................................................ 5-11
Set Supervisor Password (Security Menu) ............ 5-11
Set User Password (Security Menu) ......................5-12
Password on boot: (Security Menu) .......................5-12
Boot Menu ............................................................. 5-13
Exit Menu .............................................................. 5-15
Upgrading The Computer
Overview ..................................................................6-1
When Not to Upgrade ............................................6-2
Removing the Battery .............................................. 6-3
Upgrading the Hard Disk Drive ............................... 6-5
Upgrading the Optical (CD/DVD) Device .............. 6-8
Upgrading the System Memory (RAM) .................. 6-9
Upgrading the Processor ........................................ 6-12
XVI
Preface
Modules & Options
Overview ..................................................................7-1
Mini-PCI WLAN Module ........................................7-2
MSI 6833 WLAN Driver Installation ...................7-3
Bluetooth Module .....................................................7-6
Bluetooth Driver Installation ................................7-6
PC Camera Module ..................................................7-8
Sertek PC Camera Driver Installation ...................7-9
PC Camera Audio Setup .....................................7-10
BisonCap .............................................................. 7-12
Eliminating Screen Flicker ..................................7-13
Port Replicator Module ..........................................7-14
Port Replicator Setup Instructions: .....................7-15
Port Replicator Serial (COM) Port Driver ..........7-16
Port Replicator Network (LAN) Driver ..............7-16
Troubleshooting
Overview ..................................................................8-1
Basic Hints and Tips ................................................8-2
Backup and General Maintenance ............................8-3
Viruses ...................................................................... 8-4
Upgrading and Adding New Hardware/Software ....8-5
Power ........................................................................8-7
Display .....................................................................8-9
Boot Password .......................................................8-10
Audio & CD Device .............................................. 8-11
Keyboard ................................................................ 8-12
Operation ............................................................... 8-13
Modules ................................................................. 8-14
Interface (Ports & Jacks)
Overview ................................................................. A-1
Notebook Ports and Jacks ....................................... A-2
Built-In Microphone ...............................................A-2
Card Reader Port .....................................................A-2
DC-In Jack ...................... ... .... .... .............................A-2
External Monitor (VGA) Port .................................A-2
Headphone-Out Jack ...............................................A-2
Line-In Jack ............................................................A-2
Microphone-In Jack ................................................A-3
RJ-11 Phone Jack ....................................................A-3
RJ-45 LAN Jack ......................................................A-3
Security Lock Slot ..................................................A-3
S/PDIF-Out Jack .....................................................A-3
USB 2.0/1.1 Ports ...................................................A-3
Optional Port Replicator Ports and Jacks ............... A-4
DC-In Jack ...................... ... .... .... .............................A-4
External Monitor (VGA) Port .................................A-4
Parallel Port .............................................................A-4
XVII
Preface
Serial Port ................................................................A-4
RJ-45 LAN Jack ......................................................A-4
USB 2.0/1.1 Ports ....................................................A-5
Video Driver Controls
VIA Video Driver Installation .................................B-1
Advanced Video Controls .......................................B-2
Video Driver Controls ..........................................B-2
Video Memory .....................................................B-2
S3Tray Plus Utility ................................................B-3
S3 Display Control Panels ...................................B-4
Display Devices .......................................................B-5
Display Modes .........................................................B-6
Specifications
Processor .................................................................C-2
Core Logic ...............................................................C-2
Memory ................................................................... C-2
Security ....................................................................C-2
BIOS ........................................................................ C-2
LCD ......................................................................... C-2
Video Adapter .........................................................C-3
Storage .....................................................................C-3
Audio ....................................................................... C-3
Keyboard & Pointing Device ...................................C-3
PCMCIA ..................................................................C-3
Interface ...................................................................C-4
Card Reader .............................................................C-4
Communication ........................................................C-4
Power Management .................................................C-4
Power .......................................................................C-5
Environmental Spec .................................................C-5
Physical Dimensions & Weight ...............................C-5
Optional ...................................................................C-6
XVIII
Preface
Overview 1 - 1
Quick Start Guide
1
Chapter 1: Quick Start Guide
Overview
This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the
computer and to getting your system started. The remainder of the manual covers the following:
• Chapter 2 A guide to using some of the main features of the computer e.g. the storage devices (hard disk,
optical device, 4-in-1 card reader , PC Card), Auto Mail Program, Touch Pad & Mouse, Audio
& Printer.
• Chapter 3 The computer’s power saving options.
• Chapter 4 The installation of the drivers and utilities essential to the operation or improvement of some of the
computer’s subsystems.
• Chapter 5 An outline of the computer’s built-in software or BIOS (Basic Input Output System).
• Chapter 6 Instructions for upgrading your computer.
• Chapter 7 A quick guide to the computer’s Wireless LAN, Bluetooth, PC Camera and Port Replicator
modules (some of which may be optional depending on your purchase configuration).
• Chapter 8 A troubleshooting guide.
• Appendix A Definitions of the interface, ports/jacks which allow your computer to communicate with external
devices.
• Appendix B Information on the video driver controls.
• Appendix C The computer’s specification.
1 - 2 Overview
Quick Start Guide
1
Model Differences
This notebook series includes two different model types. The models diffe r slightly in design style inclu ding the
LCD type, and the location of the card reader. See Figure 1 - 1 below and Table 1 - 1, on page 1 - 3 for an outline
of the model differences.
Figure 1 - 1 - Model Differences
Model A Model B
Overview 1 - 3
Quick Start Guide
1
Table 1 - 1 - Model Differences
Feature Model A Model B
LCD Type
15.0” XGA (1024 * 768) TFT
OR
15.0” SXGA+ (1400 * 1050) TFT
14.0” WXGA (1280 * 768) TFT
4-in-1 Card Reader Location
Left Side Front
Hot-Key and Power Buttons
1 - 4 Overview
Quick Start Guide
1
Advanced Users
If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful
to refer to “What to Install” on page 4 - 1, “BIOS Utilities” on page 5 - 1 and “Upgrading The Computer” on
page 6 - 1 in the User’s Manual. You may also find the notes marked with a
of interest to you.
Beginners and Not-So-Advanced Users
If you are new to computers (or do not have an advanced knowledge of them) then
the information contained in the this Quick Start Guide should be enough to get you
up and running. Eventually you should try to look through all the documentation
(more detailed descriptions of the functions, setup and system controls are covered
in the remainder of the User’s Manual), but do not worry if you do not understand
everything the first time. Keep this manual nearby and refer to it to learn as you go.
You may find it useful to refer to the notes marked with a
as indicated in the mar-
gin. For a more detailed description of any of the interface ports and jacks see “In-
terface (Ports & Jacks)” on page A - 1.
Warning Boxes
No matter what your level please pay careful attention to the warning and safety information indicated by the
symbol. Also please note the safety and handling instructions as indicated in the Preface.
Notes
Check the light colored
boxes with the mark
above to find detailed
information about the
computer’s features.
Overview 1 - 5
Quick Start Guide
1
Not Included
Operating Systems (e.g. Windows XP) and applications (e.g. word processing, spreadsheet and database programs) have their own manuals, so please consult the appropriate manuals.
System Software
Your computer may already come with system software pre-installed. Where this is not the case, or where you
are re-configuring your computer for a different system, you will find this manual refers to the Microsoft Win-
dows XP (Home & Professional Editions) operating system.
Drivers
If you are installing new system software, or are re-configuring your computer for a different system, you will need to install
the drivers listed in “Drivers & Utilities” on page 4 - 1. Drivers are programs which act as an interface between the computer and a hardware component e.g. a wireless network module. It is very important that you install the drivers in the order
listed in Table 4 - 1, on page 4 - 6. You will be unable to use most advanced controls until the necessary drivers and utilities are properly installed. If your system hasn’t been properly configured (your service representative may have already
done that for you), refer to “What to Install” on page 4 - 1 for installation instructions.
1 - 6 System Startup
Quick Start Guide
1
System Startup
1. Remove all packing materials.
2. Place the computer on a stable surface.
3. Securely attach any peripherals you want to use with the notebook (e.g. keyboard and mouse) to their ports.
4. Atta ch the AC/DC adapter to the DC-In jack on the right of the computer, then plug the AC power cord into an
outlet, and connect the AC power cord to the AC/DC adapter (Note: If you have included the Port Replicator in
your purchase option see page 7 - 14).
5. Raise the lid/LCD (you will need to press the LCD latch to release
the lid of Model A computers) to a comfortable viewing angle, and
press the power button to turn the computer “on”.
6. Adjust the LCD panel to a comfortable viewing angle.
7. The LED Power & Communication ind icators show the power and
battery status of the computer, and give notification of e-mail
received.
Figure 1 - 2 - Computer with AC/DC Adapter Plugged-In
Shutdown
Please note that you should always shut your computer down by choosing the Turn Off Computer command from the
Start menu in Windows. This will help prevent hard disk or system problems.
System Map: Model A - Top View with LCD Panel Open 1 - 7
Quick Start Guide
1
System Map: Model A - Top View with LCD Panel Open
Figure 1 - 3 - Model A - Top View with LCD Panel Open
2
4
1
6
8
3
5
9
7
1. Optional Built-In PC Camera
2. LCD
3. LED Status Indicators
4. Hot-Key Buttons
5. Power Button
6. Keyboard
7. Built-In Microphone
8. TouchPad and Buttons
9. LED Power & Communication
Indicators
4
5
3
Wireless Device
Operation Aboard
Aircraft
The use of any portable
electronic transmission
devices aboard aircraft is
usually prohibited. Make
sure the module(s) are
OFF if you are using the
computer aboard aircraft.
Use the key combinations
to toggle power to the
WLAN/Bluetooth modules, and check the status
indicator icon to see if the
modules are powered on
or not (see Table 1 - 3, on
page 1 - 9/Table 1 - 5, on
page 1 - 11).
1 - 8 System Map: Model B - Top View with LCD Panel Open
Quick Start Guide
1
System Map: Model B - Top View with LCD Panel Open
Figure 1 - 4 - Model B - Top View with LCD Panel Open
2
5
1
7
8
4
1. Optional Built-In PC Camera
2. LCD
3. Speaker
4. LED Status Indicators
5. Hot-Key Buttons
6. Power Button
7. Keyboard
8. TouchPad and Buttons
9. LED Power & Communication
Indicators
10. Built-In Microphone
6
9
3
Wireless Device
Operation Aboard
Aircraft
The use of any portable
electronic transmission
devices aboard aircraft is
usually prohibited. Make
sure the module(s) are
OFF if you are using the
computer aboard aircraft.
Use the key combinations
to toggle power to the
WLAN/Bluetooth modules, and check the status
indicator icon to see if the
modules are powered on
or not (see Table 1 - 3, on
page 1 - 9/Table 1 - 5, on
page 1 - 11).
5
6
4
10
Quick Start Guide
LED Indicators 1 - 9
1
LED Indicators
The two sets of LED indicators (LED Status Indicators and LED Power & Communication Indicators)
on the computer display helpful information about the
current status of the computer.
Table 1 - 2 - LED Status Indicators
Table 1 - 3 - LED Power & Communication Indicators
Icon Color Description
Green
Number Lock Activated (to activate
press Fn & NumLk)
Green Caps Lock Activated
Green
Scroll Lock Activated (to activate
press Fn & ScrLk)
Icon Color Description
Green The Computer is On
Blinking
Green
The Computer is in Standby
Mode
Orange
The AC/DC Adapter is Plugged
In & the Computer is Powered
Off
Orange
The AC/DC Adapter is Plugged
In & the Battery is Charging
Blinking
Orange
The Battery has Reached
Critically Low Power Status
Green The Battery is Fully Charged
Blinking
Green
New Mail Has Arrived
Green Hard Disk Activity
Green
The WLAN Module is Powered
On
Orange
The Bluetooth Module is
Powered On
Quick Start Guide
1 - 10 Hot-Key Buttons & Keyboard
1
Hot-Key Buttons & Keyboard
These buttons give instant access to the default Internet browser and e-mail program, and to a user-defined
application, with one quick button press. To use the
“user-defined application Hot-Key Button”, you must
install the driver (see “Hot-Key (WinXP)” on page 4 -
10).
Table 1 - 4 - Hot-Key Buttons
See “Application Hot-Key” on page 2 - 10 for configuration instructions.
The keyboard has an embedded numerical keypad for
easy numeric data input, and features Function Keys to
allow you to change operational features instantly (see
Figure 1 - 5).
Figure 1 - 5 - Keyboard
Hot-Key Function
Activate the user specified application e.g.
Microsoft Word or Excel
Activate the Default E-Mail Program
Activate the Default Internet Browser
Fn Key
Function Keys
NumLk &
ScrLk Keys
Numeric
Keypad
Other Keyboards
If your keyboard is damaged or you just want to make
a change, you can use any standard USB keyboard.
The system will detect and enable it automatically.
However special functions/hot keys unique to the system’s regular keyboard may not work.
Loading...