USER MANUAL FOR YOUR PROSSIMO
PDW6-SL/W 60 cm Full Height
Freestanding Dishwasher
NOTE: This User Instruction Manual contains important
information, including safety & installation points, which will
enable you to get the most out of your appliance. Please keep it
in a safe place so that it is easily available for future reference; for
you or any person not familiar with the operation of the appliance.
JW 07/01/13
Contents
Environmental note 3
Important safety information 4 – 6
Specifications 7 – 10
Product and aperture dimensions 7
Product specifications 7 - 8
Electrical details 8
Description of the appliance 9
Control panel 10
Using your dishwasher 10 - 21
Before first use 10
Filling with rinse aid 11
Setting the rinse aid level 12
Filling with dishwasher detergent 12 - 13
Loading the upper basket 14
Adjusting the upper basket 14
Loading the lower basket 15
The cutlery basket 16
Loading dishes and cutlery 16 - 17
Program table 18
Setting a wash program 19
Changing a wash program 19
At the end of a wash program 20
Adding an item to the wash cycle 20
Delay start 20
Rinse aid and salt indicator neons 20
Saving energy using your dishwasher 21 - 22
Cleaning and maintenance 22 - 24
The filter system 22
Cleaning the filters 22 - 23
Cleaning the spray arms 23
Cleaning the control panel 23
Cleaning the door 24
Error code failure system 24 - 28
General troubleshooting 26 - 28
Installation 28 - 32
Connecting to the mains water supply 28
Connecting to the water outlet 29
Connecting to the power supply 30
Applying the condensation strip 30 - 31
Levelling the appliance 31
Before first use 31
Contact details 32
2
ENVIRONMENTAL NOTE
Note
disconnect it from the power supply. Cut off and render any plug
useless. Cut the cable off directly behind the appliance to prevent
misuse. This should be undertaken by a competent person. Disable
the door lock to make sure that children cannot get stuck inside
the appliance.
: Before discarding an old appliance, switch off and
o The packaging materials that Prossimo uses are environmentally
friendly and can be recycled.
o Please discard all packaging material with due regard for the
environment.
3
IMPORTANT SAFETY INFORMATION
Your safety is of the utmost importance to Prossimo.
Please make sure that you read this instruction booklet
before attempting to install or use the appliance. If you
are unsure of any of the information contained in this
booklet, please contact the retailer where you purchased
your unit.
General Safety
o Repairs to your appliance must only be carried out by authorised
service agents. Any attempt by an inexperienced person to
repair the appliance, could result in injury or damage to your
dishwasher.
o If you notice that the mains cable is damaged. The appliance
must not be used. The same applies if you notice that the
worktop, control panel or base area is damaged. As this could
allow access to the internal components of the machine.
o The appliance should be turned off and isolated from the mains
supply, before either cleaning or maintenance work is attempted.
o The mains cable must not be used to pull the plug out of the
electrical socket.
o The machine should not be sprayed with water.
o The external surface of the appliance may become hot whilst
your dishwasher is in use.
o It is possible for small animals to chew either mains cables or
water hoses, which could cause an electric shock hazard.
Installation
o The installation instructions contained within this user manual
should be followed.
o It is obligatory for the completed installation to comply with all
relevant building regulations and local water authority
requirements.
o Before the first use of the appliance, you should follow the
steps listed in the “Before first use” section on page 11
and page 31 of this manual.
4
o Care should be taken not to trap the power supply cable
underneath the appliance whilst installing it.
o No attempt should be made to alter or modify the specifications
of this appliance.
In daily use
o This appliance is only designed to wash normal domestic
washloads. If you use your dishwasher in any other way or it is
incorrectly used, then the manufacturer accepts no liability for
any damage that might be caused and any guarantee will be
void.
o It is recommended that the appliance is unplugged and the
water supply is turned off after the machine is used.
o The detergents and rinse aid that you place in this appliance
should be suitable for automatic dishwashers. With regards to
dosage levels, the detergent manufacturer’s recommendations
should be followed.
o Sharp knifes or ones with long blades are a potential safety
hazard when placed in an upright position in the cutlery basket.
We would recommend that these items are placed horizontally in
the upper basket.
o You should not wash any items that have come into contact
with corrosive, acidic or alkaline chemicals, paint, petrol, iron or
steel debris.
o You should not open the door whilst the appliance is set on a
wash program. Depending on which stage that the wash
program is at, hot water could escape the machine.
o You should not leave the door of the appliance open, unless
you are loading or unloading the dishwasher.
o You should not stand or sit on the door when it is open.
5
Child Safety
o Your dishwasher should only be used by adults. You should not
allow children in the area of the machine unsupervised. You
should not let them touch the controls or play with the appliance.
o It could be possible for a child or pet to gain access to the
dishwasher if the door is left open. Therefore please check the
inside of the appliance before setting it on a wash cycle.
o Any packaging that is removed from the machine should be kept
away from children.
o All detergents should be kept out of children’s reach in a safe
place.
o Some water will remain inside the dishwasher when it has
completed a wash cycle. This water is not suitable for drinking
and may contain residues from the detergents that are used in
the appliance.
Declaration of conformity
o This appliance complies with the standards currently in force.
6
Specifications
Product dimensions
Height: 850 - 875 mm
Width: 600 mm
Depth: 600 mm
Product specifications
o 12 Place settings
o 3 functions: Normal
Intensive
Rapid
o 5 temperatures: 40°C, 45°C, 49°C, 55°C, 65°C
o Noise level: 52 dB
o Delay start
o Anti-leak device
o Anti-flood device
o Concealed heating element
o Collapsible plate racks
o Height adjustable upper basket
o Adjustable feet
o Residual drying
Energy efficiency details
Energy efficiency class: 3 Star
7
Electrical details
Rated voltage: 220-240 Vac 50 Hz
Supply connection: 10 A
For future reference please record the following information which can
be found on the rating plate and the date of purchase which can be
found on your sales invoice. The rating plate of your dishwasher is
located on the right hand side of the drop down door.
Model Number ……………………………….
Serial Number ……………………………….
Date of Purchase ……………………………….
8
Description of the appliance
1) Upper basket
2) Spray arms
3) Lower basket
4) Filters
5) Detergent dispenser
6) Rinse Aid dispenser
7) Cutlery basket
8) Cup holder
9
Control panel
1) ON/OFF button
2) Delay start button
3) Child lock buttons
4) Start/Pause button
5) Rinse aid indicator
6) Drying indicator
7) Program selection buttons
10
Using your dishwasher
Before first use
Filling with rinse aid
The rinse aid is released during the final rinse and it helps
to prevent water from forming droplets on your dishes.
These droplets will lead to spots and streaks being left on
items after the wash program has completed.
o Your dishwasher is designed to utilise liquid rinse aid.
o The rinse aid dispenser is located inside the drop down door,
next to the detergent dispenser.
o To access the rinse aid dispenser, you should turn the cap
anticlockwise and it will pop out of the hole. Then slowly pour in
liquid rinse aid, the rinse aid dispenser will hold approximately
140 ml of rinse aid.
o You should continue to fill with rinse aid, until the level indicator
turns completely black.
o Be careful not to overfill the dispenser, as this could cause
oversudsing when a wash program is selected. Wipe away any
rinse aid excess or spillages with a damp cloth.
o Replace the cap and turn it clockwise until it locks into position.
o You should refill the rinse aid dispenser when the rinse aid
indicator lights on the control panel (5).
o IMPORTANT: If you are using 3 in 1 dishwasher tablets then
you should still fill the rinse aid dispenser.
11
Setting the rinse aid level
The amount of rinse aid that the dishwasher requires also depends on
the hardness of your water. You should experiment with the rinse aid
setting, until you find a level that gives the best results.
o On the first wash cycle, we would
recommend that the rinse aid level is
set to number 4.
o If you get water spots and poor drying
performance, then you should turn the
arrow anticlockwise and increase the
setting to the next number.
o You should continue to adjust the rinse aid level upwards until
you get no water spots.
o If you get cloudiness or streaking on your dishes, the rinse aid
level is set too high and it is causing foaming during the wash
cycle. Turn the arrow clockwise and lower the setting to the next
number.
Filling with dishwasher detergent
The detergent dispenser must be refilled at the start of each wash
cycle (apart from the Rinse wash program).
o Open the lid that closes over the detergent dispenser and place
the detergent inside the dispenser.
o The section marked 1 in the diagram
is for the main wash cycle detergent.
Only one detergent tablet should be
placed in the dispenser at any one
time. If you are using detergent
powder or liquid, you should follow
the detergent manufacturer’s
recommendations.
12
o The section marked 2 in the diagram can have separate
detergent placed in it for any wash cycle that has a pre-wash
element to it, however this is optional. This must be a liquid or
powder detergent, not another detergent tablet.
o Shut the detergent dispenser lid so that it clicks shut securely.
o At the beginning of a wash cycle the clip will open and the
tablet/powder/liquid will enter the dishwasher.
Concentrated detergent
o The use of the NORMAL program with concentrated detergents
reduces pollution and is good for your dishes.
o This wash program is specifically suited to the dirt-dissolving
properties of the enzymes of concentrated detergent. For this
reason, the NORMAL program, in which concentrated detergent
is used, can achieve the same results achieved in the INTENSIVE
program.
Detergent tablets
o Different brands of detergent tablets dissolve at different speeds.
For this reason, some detergent tablets cannot dissolve and
develop their full cleaning power during short programs.
o It is recommended that you use longer programs when using
detergent tablets to ensure the complete removal of detergent
residues.
o If you are using 3 in 1 detergent tablets you should check that
the water hardness in your supply is compatible with the use of
these products, as per the detergent manufacturer’s instructions.
o 3 in 1 detergent tablets contain detergent, rinse aid and salt,
and as such it may be beneficial to select the lowest setting for
water hardness. See ‘setting the rinse aid’ section for details.
13
Loading the upper basket
The upper basket is most suited to washing delicate and light
dishware, such as glasses, coffee & tea cups, saucers, plates, bowls
and shallow pans (that are not heavily soiled).
A. Cups
B. Glasses
C. Saucers
o You should position the dishes
and cookware in such a way that
they are not moved by the spray
of water during the wash cycl
e.
o Use the diagram above as a guide to the most appropriate way
to load the upper basket.
Adjusting the upper basket
Your dishwasher has an adjustable upper basket which you can alter to
the most suitable position for the items you are going to wash in the
upper and lower baskets.
o The height of the upper basket can be adjusted by placing the
wheels on a different height of the rails. Long items such as
cutlery, salad servers and knives should be placed on the shelf
so they do not obstruct the rotation of the spray arms.
o IMPORTANT: The upper basket must be empty when you are
removing it from the guide supports.
o NOTE: For easier stacking of pots and pans the cup shelf spikes
can be folded down.
14
Loading the lower basket
The lower basket is most suited to washing larger and more heavily
soiled items, such as saucepans, saucepan lids and serving dishes. You
can also load bowls and a variety of plates into the lower basket.
G. Dessert dishes
H. Dinner plates
I. Side plates
o Saucepans and serving bowls must
always be placed with their bases
upwards.
o Deep saucepans should be slanted,
to allow water to run off.
Folding spikes of lower basket
o The bottom rack has
prongs that can be folded
downwards, to allow for
easier loading of larger
saucepans and serving
bowls.
15
The cutlery basket
Cutlery should be placed inside of the cutlery basket. The
cutlery basket should then be placed in the appropriate
position in the lower basket.
1. Teaspoons
2. Dessert spoons
3. Soup spoons
4. Forks
5. Knives
o For the best washing performance, cutlery
should be placed through the slots in the
top of the cutlery basket.
IMPORTANT: Do not allow items of cutlery to fall
through the bottom of the cutlery basket, as this
may cause damage to the spray arm and/or the
cutlery. If the bottom of the basket begins to
deteriorate and allows items to fall through, you
should replace the cutlery basket.
Loading dishes and cutlery
Household cloths, sponges or any other object that may
absorb water SHOULD NOT be washed in a dishwasher.
o Remove leftovers and soften the remnants of burnt food in pans,
prior to loading dishes in the appliance.
o Once the dishwasher has been loaded, check that the spray arms
can move freely. If the spray arm comes into contact with any
item, then you should rearrange the wash load.
o Cups, glasses, pans etc should all be loaded with their bases
upwards, so that water does not collect inside of them.
o Cutlery and dishes should not cover each other; otherwise you
may get poor wash results.
o Do not allow glasses to touch inside the dishwasher, otherwise
damage may occur.
o Small objects can be placed inside of the cutlery basket.
16
The following items are NOT suitable for washing
inside a dishwasher:-
o Cutlery with a handle of mother-of-pearl, wood, horn or china.
o Plastic items that are not resistant to heat.
o Cutlery that consists of glued parts that are not resistant to heat.
o Cutlery items or crockery that are bonded.
o Copper or pewter items.
o Lead crystal glass.
o Wooden platters.
o Synthetic fibre items.
The following items are not always suitable for
washing inside a dishwasher:-
o Stoneware should only be washed if the manufacturer of the
item has marked it as dishwasher safe.
o Plastic items (such as lunchboxes) should only be washed if the
manufacturer has marked it as dishwasher safe.
o Glazed crockery may fade with repeated washing inside of a
dishwasher.
o Items made of silverware or aluminium can discolour when
washed inside a dishwasher.
o Any food residue should be removed from silver items
immediately, as this can also result in discolouration.
o Certain types of glass may become dull or cloudy after a large
number of washes.
17
Program table
o The ECONOMY program is suitable for cleaning a typical load of
dirty dishes and is the most efficient in terms of its combined
energy and water consumption.
Program Program
information
Normal
**
For normally soiled
loads, such as pots,
plates, glasses and
lightly soiled pans.
Intensive
Rapid
For the heaviest
soiled loads, such as
pots, pans,
casserole dishes and
dishes that have
been sitting with
dried food on them
for awhile.
A shorter wash for
lightly soiled loads
that do not need
drying.
* The wash program times that are quoted are intended as a guide
only. Please note that factors external to the machine, e.g. the
temperature of your water supply, your water pressure etc. can affect
the time it takes for the wash program to complete.
** NORMAL is the testing program for AS/NZS.2007.1
Description
of cycle
Wash (45°C)
Rinse
Hot rinse
(49°C)
Drying
Pre-wash
(40°C)
Wash (55°C)
Rinse
Hot rinse
(65°C)
Drying
Wash (40°C)
Hot rinse
(49°C)
Detergent
pre/main
5 grams
(pre-rinse)
25 grams
(main wash)
Or 3 in 1
5 grams
(pre-rinse)
25 grams
(main wash)
Or 3 in 1
15 grams
(main wash)
Program
times*
112
Minutes
145
Minutes
50
Minutes
Energy
(kWh)
0.73 11.8
1.20 15.5
0.50 7.5
Water
(L)
18
Setting a wash program
Make sure that the before first use section has been
followed.
o Check whether the appliance needs rinse aid adding to it.
o Pull out the top and bottom baskets, then load them in
accordance with the loading instructions.
o Push the top and bottom baskets fully back into position.
o Add detergent.
o Close the dispenser before starting the dishwasher
o Close the door firmly, so that you hear the door lock click shut.
o Turn the appliance on by using the ON/OFF button.
o IMPORTANT: Wait for 5 seconds before pressing the
program selection button, otherwise the appliance may
not function correctly.
o Press the program selection button to choose an appropriate
wash program for the load that you are washing. Where
applicable, the relevant program indicator will light to show
which program you have selected.
o After a few seconds, you will hear the appliance begin to fill with
water and the wash program will have started.
Changing the wash program
IMPORTANT: This should only be attempted when the cycle has
only just started, otherwise the detergent tablet may have
already released or you could have hot water escaping.
o Turn off the appliance using the on/off button and wait for a
minute.
o Turn the appliance back on using the on/off button.
o Select your new wash program.
o After about 10 seconds you will hear the appliance begin to fill
with water and the wash program will have started.
19
At the end of a wash program
o When the wash program is finished a buzzer will sound.
o Open the door of the appliance.
o Use the ON/OFF button to switch the dishwasher off.
o Wait a few minutes before unloading the dishwasher to avoid
handling the dishes and utensils while they are still not and more
susceptible to breakages. They will also dry better.
Adding an item to a wash cycle
IMPORTANT: This should only be attempted when the cycle has
only just started, otherwise the detergent tablet may have
already released or you could have hot water escaping.
o Slightly open the door of the appliance and wait for a minute before
fully opening the door to avoid scalding by the hot water.
o The cycle will pause. The machine will emit a beep and the
“Intensive” and “Normal” LED’s will flash. This is an error signal
caused by opening the door.
o Add the item and then close the door. The cycle will resume after
approximately 10 seconds.
Delay start
o Set your desired wash program as outlined on page 18.
o Press the delay start button to delay the start of the wash.
o Keep pressing the delay start button until your desired amount of
delay is displayed (in hours):
Off – 3 hours – 6 hours – 9 hours – Off.
o The maximum amount of delay is 9 hours.
Rinse aid indicator
o The rinse aid indicator on the control panel will let you know when
the appliance needs rinse aid adding to it.
o The
light indicates that you need to add rinse aid to the
appliance. You should follow the procedure outlined on pages 11.
20
Saving energy using your dishwasher
Loading dishes
o Refer to the relevant section of this manual for instructions on
placing items in the dishwasher for the most efficient cleaning.
o Only run the dishwasher when it is full for optimum energy and
water usage.
o Check the program table to select the most efficient program
according to the size and type of the load.
Usage
o Clean the filters regularly both to keep the dishwasher clean and to
maintain its efficiency.
o Always remember to switch the appliance off standby when you
have finished using it. Energy is wasted by leaving appliances on
standby.
o You do not need to rinse dishes off before loading. If you prefer to
pre-rinse, use cold water on your dishes before loading them but do
not waste water by letting it run continuously.
o Use the shorter and lower temperature cycles for everything but the
dirtiest dishes. Shorter cycles use less energy and work just as well.
Modern detergents also work just as well at lower temperatures.
21
Cleaning and maintenance
IMPORTANT: The appliance should be disconnected from
your mains supply before commencing any cleaning process.
The filter system
Your appliance is fitted with three levels of filtering; these are located
in the base of the dishwasher for ease of access.
1) Main filter
2) Coarse filter
3) Fine filter
Main filter- Food and soil particles are trapped by this filter and
pulverised by a special jet on the lower spray arm.
This debris is then washed down the drain.
Coarse filter- Larger items such as pieces of bone or glass, which
could clog the drain, are trapped in this filter.
Fine filter- This filter holds soil and food residue in the sump
area and prevents it from being redeposited on the
dishes during a wash cycle.
IMPORTANT: Whilst the filtering system is efficient, your
dishwasher is not a waste disposal unit. All items being
washed inside of the dishwasher should have food scraps
removed from them before being loaded into the appliance.
Cleaning the filters
For best performance and results, the entire filter assembly should be
thoroughly cleaned regularly (ideally after each wash cycle).
1. Turn the coarse filter anti-clockwise and
then lift it upwards. The fine filter will come
out with the coarse filter. Rinse out these
sections under a tap to remove any food
debris that remains in it.
22
2. Pull out the main filter and rinse this under
the tap to remove any food debris that is
trapped in it.
3. Place all filters back in their original
position.
4. You must turn the coarse
filter clockwise to
lock it back into position.
IMPORTANT: If a glass gets smashed inside of the appliance,
you must check there is no glass in the filter before the
machine is used ag
ain as this can cause a drainage failure.
IMPORTANT: THE DISHWASHER SHOULD NEVER BE
SET ON A WASH CYCLE WITHOUT THE FILTERS BEING
INSIDE OF THE APPLIANCE.
Cleaning the spray arms
The spray arms should be cleaned regularly, to prevent hard water
deposits from clogging the spray arm jets and bearings.
o To remove the top spray arm,
unscrew the nut and take out
the washer that sits on top of
the spray arm and pull to
remove.
o Gently pull upwards to remove
the bottom spray arm.
o Wash the spray arm in warm,
soapy water and use a soft
brush to clean the jets.
o Rinse the spray arm thoroughly
and then reassemble the spray
arm back in its original
position.
Cleaning the control panel
IMPORTANT: Do not use any abrasive cleaner or household polish on
either the control panel or operating parts.
o Wipe over the control panel using a brand new damp cloth with
warm water.
23
Cleaning the door
o To clean the edge around the outside of the
door, you should use a soft, damp cloth only.
o To prevent water from penetrating the door
lock or electrical components, DO NOT use a
spray cleaner of any kind.
o DO NOT use any abrasive cleaner or scouring pads on the inner or
outer surfaces, as they may cause damage to them.
Error code failure system
The following error codes (Flashing display neon’s) can possibly be
remedied by the customer and the maintenance steps outlined below
should be followed.
BEFORE COMPLETING ANY MAINTAINEANCE ON THE
APPLIANCE, IT SHOULD BE DISCONNECTED FROM YOUR MAINS
POWER SUPPLY.
“Delay start” (6 hours) and “Intensive” LED indicators flash
o Longer than expected fill time.
Check the water pressure of your mains water supply.
Clean the mesh filter that sits in the inlet hose.
Ensure that the inlet hose is not kinked or crushed.
Make sure the water tap that the machine is connected to is
turned on fully.
Make sure the drain hose has been connected as specified.
“Delay start” (3 hours) and “Intensive LED indicators flash.
o Longer or extended drain time.
The drain pipe may be placed in too high a position or
incorrectly. Check the installation instructions and ensure that
the installation is correct.
Check that the outlet hose is not kinked or crushed.
Make sure that the drain hose has not been extended beyond its
original length.
“Delay start” (3 hours) and “Normal” LED indicators flash.
o The machine has sensed water in the base.
Check that the outlet hose is not kinked or crushed.
Check that there are no blockages in the drain hose or the
drainage system that the appliance is connected to.
The drain pipe may be placed in too high a position or
incorrectly. Check the installation instructions and ensure that
the installation is correct.
24
Other error codes:
ERROR CODE MEANING POSSIBLE CAUSES
“Intensive” and
“Normal”
Door open The door is open when the
dishwasher is operating
indicators flash
“Normal” and
“Rapid”
Temperature
sensor
Temperature sensor malfunction
indicators flash
“Rapid” and
Water leakage Water leakage occurs
“Delay”
(3 hours)
indicators flash
“Rapid” and
Heating element Abnormal heating
“Delay”
(6 hours)
indicators
flash.
IMPORTANT: If any of the above fault codes appears then you
should check the trouble shooting table on pages 26-27 for
possible solutions. If no solution can be found or an error code
not listed is displayed then you should disconnect your
appliance from the mains supply and contact customer service
immediately, quoting the error code.
FOR THE ABOVE FAULT CODES, IF THE CODE REAPPEARS AFTER
FOLLOWING THE ADVICE AND CLEARING THE FAULT CODE YOU
SHOULD TURN OFF THE APPLIANCE. DISCONNECT THE
APPLIANCE FROM YOUR MAINS SUPPLY AND THEN ARRANGE
FOR A SERVICE TECHNICIAN TO ATTEND THE APPLIANCE BY
CONTACTING THE CUSTOMER SERVICE DEPARTMENT.
Please note that if a service technician is asked to attend whilst the
product is under guarantee and finds that the problem is not the result
of an appliance fault, then you may be liable for the cost of the call out
charge.
The appliance must be accessible for the service technician to
perform any necessary repair. If your appliance is installed in
such a way that an engineer is concerned that damage will be
caused to the appliance or your kitchen, then they will not
complete a repair.
This includes situations where appliances have been tiled in,
sealed in with sealant, have wooden obstructions placed in
front of the appliance, like plinths. Or any installation other
than the one specified by the manufacturer has been
completed.
25
Please refer to the conditions of guarantee that appear on the
warranty card that you receive with the appliance.
IMPORTANT: The manufacturer operates a policy of continuous
improvement and reserves the right to adjust and modify its
products without prior notification.
General troubleshooting
PROBLEM POSSIBLE
CAUSES
Dishwasher
doesn’t
run
Drain pump
doesn’t stop
Noise Some audible sounds
Fuse blown or the
circuit breaker has
tripped
Power supply is not
switched on
Water pressure is
low
Overflow The system is designed to detect an
are normal
Utensils are not
secure in the baskets
or something small
has dropped into the
basket
Motor hums
Replace the fuse or reset the circuit
breaker. Remove any other
appliances that are sharing the same
circuit with the dishwasher.
Make sure that the dishwasher is
turned on and that the door is closed
securely.
Make sure that the power cord is fully
plugged into the wall socket.
Check that the water supply is
connected properly and that the
water is turned on.
overflow. If it does, then it will run
the drain pump continuously when
there is power to the appliance.
You will get a level of operating noise
during a wash cycle, in particular
when food is being removed from
items and when the detergent
dispenser places the tablet into the
tub.
Ensure that everything is loaded as
per The manufacturer’s loading
instructions.
If the dishwasher is not going to be
used for a period of time, then you
should make sure that the appliance
is set on a wash program once a
week. Otherwise the seal around the
motor may dry out and cause noise.
WHAT TO DO
26
Suds in the
tub
Improper detergent
use
Spilled rinse aid
Ensure that if you are using 3 in 1
detergent tablets in conjunction with
rinse aid that the levels are set
correctly.
Always wipe up any excess rinse aid
or rinse aid spillages immediately.
Stained tub
interior
Dishes are not
fully dried
Dishes and
pans are not
clean
Spots and
filming on
glasses and
pans
Steam A normal
Detergent with
colourant was used
Rinse aid dispenser
is empty
Improper program
Improper loading
Extremely hard
water
Low inlet
temperature
Improper loading
Improper detergent
Improper rinse aid
levels
phenomenon
Use a detergent without colourant.
Make sure that the rinse aid
dispenser is filled with rinse aid.
Select a more intense wash program.
Make sure that the spray arms and
the detergent dispenser are not being
impeded by large dishes.
Refer to the relevant sections of this
booklet, to ensure that the detergent,
and rinse aid levels are set correctly.
Ensure that the appliance is loaded
correctly.
You may get a small amount of steam
coming through the vent by the door
latch, during drying and water
draining.
Black or grey
marks on
dishes
Water
standing in
the bottom of
the tub
Dishwasher
leaks
Aluminium utensils
have rubbed against
dishes
This is normal A small amount of clean water in the
The rinse aid
dispenser is
overfilled or rinse aid
has been spilt inside
the appliance
Dishwasher isn’t
level
Use a mild abrasive cleaner to
eliminate the marks. Make sure that
the appliance is loaded correctly in
future.
base of the appliance is not
something to be concerned about.
Take care not to overfill the rinse aid
dispenser. Spilt rinse aid could cause
oversudsing and lead to overflowing.
Wipe away any spills immediately
with a damp cloth.
Make sure that the dishwasher is
level.
27
The
Dishwasher
is not
responding
The safety lock is
engaged
Turn off the safety lock by pressing
the safety lock buttons.
Turn the appliance off and on again
using the power button.
Installation
IMPORTANT: THIS INSTALLATION MUST BE
COMPLETED BY A SUITABLY QUALIFIED PERSON.
THE MANUFACTURER ONLY SANCTIONS THE
INSTALLATION GIVEN IN THIS INSTRUCTION
MANUAL. YOU SHOULD DISPOSE OF ALL PACKAGING
IN AN ENVIRONMENTALLY FRIENDLY MANNER.
Connecting to the mains water supply
IMPORTANT: Do not connect the appliance to your mains
water supply using an old or an existing water inlet hose.
The inlet hose supplied with the dishwasher is the ONLY one
that should be us
DO NOT CONNECT THE WATER INLET HOSE TO A HOT
WATER TAP.
o Connect the water inlet hose to a threaded water tap that has a
3/4” thread and to the inlet hose connector on the appliance.
o Fully tighten the inlet hose to the water tap and the dishwasher.
ed.
o Before connection, we would
advise running the water to
ensure that it is clear and free
from impurities as dirty water
could block the inlet pipe and
damage the machine.
o The inlet hose will be located
inside the cavity of the
dishwasher.
28
Connecting to the water outlet
o Secure the drain hose, so that it cannot move whilst the
dishwasher is in use.
o Place the end of the drain hose in your drain pipe and push it a
short way down (max120mm) DO NOT SEAL
o IMPORTANT: Do not insert the drain hose too deeply into the
pipe, as this may cause siphoning.
o NEVER EXTEND THE DRAINAGE HOSE FROM ITS ORIGINAL
LENGTH.
Connecting to the power supply
o IMPORTANT: The e e
once the appliance is insta
l ctrical socket must still be accessible
lled.
29
o Consult the rating plate, located
on the right hand side of the drop
down door BEFORE making the
electrical connections. Ensure that
the voltage reaching the plug is
the same a
s that on the
plate.
o DO NOT REMOVE THE RATING
PLATE AS THE
INFORMATION ON IT IS IMPORTANT.
o The moulded plug that is supplied with the appliance must be
placed into an earthed
and insulated socket.
o Broken or damaged power leads must only be replaced by a
suitably qualified person. A power lead of a similar type must be
used in replacement.
o Power lead type – H05VV–F 3G 1.5
o IMPORTANT: We do not re
commend that this appliance is
connected to an extension lead.
pplying t
A he condensation strip
The condensation strip must be fitted to the underside of the
o
worktop to protect it against the ingress of moisture. The strip
will deflect steam that rises from your appliance, away from the
underneath of the worktop.
o The condensation strip will be located inside of yo
ur dishwasher.
o Ensure that the underneath of the worktop is clean befor
sticking the strip to it.
rating
e
30
o Separate the backing paper away from the strip.
Stick the condensation strip to the underneath of the worktop.
o
o IMPORTANT: Failur
e to attach the condensation strip could
result in damage to your worktop.
Levelling the appliance
o IMPORTANT: Your dishwasher must b
e level for it to operate
properly.
o Make sure that the dishwasher is supported whilst it is being
levelled, otherwise it may tip over.
The feet can be adjusted by hand or by using a spanner.
o
o Use a spirit level to check that the
appliance is level
Check that the appliance is level from
o
side to side.
o Check that the appliance is level from
front to back.
efore first use
B
You should check the following before using the appliance for the first
time:-
o That the dishwasher is level and fixed in positio
n.
o That the water tap is fully open.
o That there are no leaks at either end of the d
rain or inlet hoses.
o That the inlet and outlet hose are fully tightened.
o That the inlet and outlet hoses are not kinked.
o That the power is switched on.
o That the rinse aid dispenser has been filled.
31
Thin td.
k Appliances Pty L
416-424 Barry Rd
Coolaroo VIC 3048
Sales Telephone
1300 132 824
Service Telephone
1800 444 357
Website
www.thinkappliances.com
32
Loading...