ProSpot Fitness PC3OOO User Manual

rM

Pno$Po$itness

Modet

Pc3ooo

Owners

Assembly

1)

2) Use Maintenance

3)

Warranty

4)

5) Parts

and

Operation

List

Manual

Instructions/Illustrations

PnoSvo'rJitnessrM

of

your PnoSrorltnessrM

of

Information

Product

Serial#:

ililililtililil iluil

17005D00055PC3000

tililtiiilt iltl

ililililtil1

Table of Contents

Assembly

and Operation

Use Periodic Maintenance of

Warranty Parts List..

Instructions.

of Your

Information.

PROSPOTy'tnessrM

vour

PROSPOTftnessrM

.......1-5

Product... ... .. .....6-7

Product.

............10

.......8

.........9

Instructions

for

Assembly of

the PROSPOT/tnessrM

PC3000

Before assembly, choose a safe PC3000 has a footprint of approximately 6'x 6'. PROSPOTfrne"^srt PC3000 away

or spilled on any electrical Approximate assembly time A flat area of 8' x 8' will be required to assemble You will need the following tools and a helper to complete the assembly:

.

5 mm Allen Wrench

.

14 mm Box End Wrench

.

17 mm Box End Wrench

.

19 mm Box End Wrench

Floor Padding, such as cardboard,

good pair

A cartons.

HAND TIGHTEN Before assembly, separate and identify

distinguished "L"&"R"stickers.

of scissors will be helpful in separating the

all bolts. DO NOT

by the

part.

is

manner in

location for

from

any source

Do not insert any object into the electrical

hours.

1/2

to avoid scratching

fully

tighten bolts until instructed

the

which the

your

of water. Do not

and

righFsided

pre-drilled

holes align with

PROSPOTJitnessn

The

barbell is approximately 7'

allow any liquid

properly

your

use the PROSPOTlrzessw

floor

during assembly.

parts

from

one another while

to do so.

parts

from the left-sided

corresponding

PC3000. The PROSPOTlrzessrs

your

from

the

are easily

by

box.

removing

parts.

parts,

long. Locate

near

to be

These

the machine

PC3000.

them

parts

or are identified

The PROSPOTliaressrM of bolt called for at each step of

.

WARNING: Never

PC3000

STEP # 1:

1. Place lllustration. holes

2.

Carefully thread the Base Rails

Attach

3. four

bolts

4.

Attach the Right

Backing Plate

(20)

as shown.

5. Attach Backing Plate

while the Power

MAIN FRAME ASSEMBLY

the two Base Rails

Place the Lower Cross Brace

ofthe Base Rails

Cross

(1

& 2) then

the two Base Rails

(28),

eight washers

Upright Guidepost Assembly

(13)

attached on the right base rail

HAND TIGHTEN the bolts

the Left Upright Guidepost

(13)

attached on the left base rail

as shown. HAND TIGHTEN

PC3000 uses

assembly. Refer to the sizing charts

perform

(1

2)

&

(1

& 2) align with

Brace Wire

pull

Wire Harness

the

(1

& 2) to the Lower Cross Brace

(18)

several different

any maintenance

Supply

opposite each other in the center

the end

Harness

and four

is

(3)

between the two Base Rails

(8)

(20)

nuts

(7

,

at this time.

Assembly

(9,

12,23) to the Lower

(2)

the bolts at this

time.

lengths

plugged

holes

of the Lower

(8)

through

of bolts. Be

provided.

into

Cross Brace

the corresponding

out of the top holes

(3)

using two Cross Brace

as shown. HAND

10, 23)

to the Lower

(1)

using two bolts

using

two bolts

(28),

careful to use the

correct length

on the PROSPOTJitnessrM

the wall !!!

of the assembly

(1

& 2) so

of the Base Rails

TIGHTEN

Cross Brace

(28),

four

Cross Brace

four washers

area as shown in

that the side

(3).

pre-drilled

side

('1

& 2).

Backing Plates

the bolts at

(3)

and the Cross Brace

washers

(18)

(3)

and the Cross

(18)

and

pre-drilled

holes

of the

this time.

and two nuts

Brace

two nuts

the

('13).

(20)

6. Plug just

under the

together both of the Cross Rail Wire

perforated

Slider Shields on back of the

Harness

(8)

to lower ends

Screen

I

of the Spiral Signal

Panels

(23).

Cables

(46)

located

7. Attach the two (28),

bolts

sixteen

Front

washers

Uprights

(18)

(4)

to the two base

and eight nuts

(1

rails

(20)

as shown. HAND TIGHTEN

2)

&

using the Upright Support Plates

the bolts at

(6),

this time.

eight

8. Attach the two

using eight time.

9. Attach the Upper Cross Brace

washers

10. Tighten all bolts and nuts used for assembly 11 Carefully flex the Left Weight Bar Cables

of each corresponding cutout in the that the cables are straight and uncrossed and cables and

12. RFrpeat

the step

Pulley

(22),

bolts

(18)

and eight nuts

Pulley

1 1

Support

sixteen washers

pulleys

Support

on the right side of the PROSPOTlrrrrersrM

Frames

(1

(20)

and

Frame

(17)

('18)

1 ) to the two Pulley Support Frames

as shown.

(24)

insert

the

(17)

and

Front

to the

eight nuts

and

HAND TIGHTEN the bolts at this

onto the

Left \ ieight Bar Knuckle

allowing

the Left Weight

Uprights

pulleys

(20)

as

steps.

(27)

pulleys

PC3000.

(4)

and the

shown. HAND TIGH-f EN

so that the cables insert

Bar

Upright Guide Posts

(17)

time.

(44)

Knuckle

move

smoothly.

STEP #2: SENSOR WEIGHT BAR INSTALLATION

1. Standing in front of the PROSPOTltzessrM PC3000. Insert one \

Jeight Bar

preinstalled

the rotation in the knuckles

2. Place until they boits

(25)

limiting

Plastic Locking

one

up

butt

securely.

into

sensor retaining

(42

against and secure the

Knuckles

the

protrudes

that & 44) as it is slid into

Sleeve

(42

collars

from the bottom of the Sensor Weight Bar

(39)

& 44],. Slide the knuckles

(45

48) at

&

position)

onto each end of the Sensoi Weight Bar

Weighi Bar

each end of the Sensor Weight

Cable Knuckle in

end and then the other

onto the Bar until

(25)

place.

Tighten

using eight

down through

(44)

that must

(25)

bolts

to hang free.

end of the

rest

they

(25). (There

Bar

and slide

Plastic Locking

(10

& 12)

the bolts at this

(52),

sixteen

into the

the rectangular

fit through

grooves

Be sure

Sensor

snugly

against

is a

a slot

them inwards

Sleeve

3. Piace one of the Olympic Adapters they touch the of the Sensor Weight Bar

Allen bolts

4.

Aitach the four small washers

5. Attach the eight

tvro washers

Note: In this manual when referring

are from the outside, facing

Plastic

(29)

and two washers

(38)

and four nuts

Side

(18)

and sixteen nuts

Locking Sleeves

(25)

so that they also

(36).

plastic pipes (15)

(35)

as shown. Tighten the bolts securely.

Weight

Plate Holders

(20)

the front of the unit.

(30)

onto the Sensor Weight

(39)

Insert an Olympic Adapter

go

Inside of

to the two Pulley Support Frames

(14)

to the two Front

as shown. Tighten the

to Left and Right side

Bar

the Olympic Adapters

Uprights

bolts securely.

of unit, the left and right

(25)

and

slide them onto

Retaining Plug

(17)

using

(4)

using sixteen

(33)

(30).

four

the Bar until

onto each

Secure

bolts

with two

(34),

(53),

perspective

end

eight

thirty-

--2--

Upright

Guidepost

Assembly

Diagram

Leat Locking

Right Lockihg

Slide.

--3--

ProSpot Fitness PC3OOO User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual