ProsKit SS-621 User Manual

SS-621 Series

HEAT GUN WITH LCD DISPLAY

1st Edition, 2011

User’s Manual

@2011 Prokit’s Industries Co., Ltd.

Specification

Model No SS-621B SS-621H

Power(w) 2000 2000
Lowest Temp.( ℃) 100 100
Highest Temp.( ℃) 650 650

Plug Type

IMPORTANT SAFETY
INSTRUCTIONS

Before using, please take a few minutes to read all instructions carefully and pay attention
to safety notices and warnings to ensure work safely. Keep these instructions for future
use.

WARNING

* To reduce risk of fire or electric shock, do not expose to rain or moisture. Store indoors.
* When servicing, use only identical replacement parts.
* Never use the heat not airflow toward people or animals.
* Never use the heat gun near flammable materials or gases.
* Never obstruct the hot airflow by blocking or covering the air outlet.
* Never touch the hot air nozzle, it becomes extremely hot.
* Wear protective work gloves at all times.
* Never touch the nozzle to any surface when running the gun or shortly after running.
* Always wear eye protection when removing paint from overhead positions.
* Do not wear loose-fitting clothing or jewelry. Wear nonskid footwear and protective cap to

wrap long hair.

* Maintain proper balance and footing at all times.
* Keep the gun handle dry, clean, and free from oil and grease.
* Do not force the tool or accessories, and use only for the purpose intended.
* Always stand gun in an upright position or hang it up by its convenient hanger.
* Never use in wet environments or areas of high humidity (for example: bathroom, steam

rooms, etc.)

* Never poke anything down inside the hot air nozzle.
* Always allow the heat gun to cool/down completely before storing it.
* Always store the gun in a safe place, out of the reach of children.
* Be aware of the work environment. Areas behind ceilings, floors, and soffits may contain

highly flammable materials. Always check these areas before applying heat.

* Keep work area with sufficient light.
* Guard against electric shock by preventing contact with grounded surfaces (for example:

pipes, radiators, ranges, refrigerator enclosures.)

* Never carry the gun by its power cord or yank the cord from an electrical outlet.
* Inspect extension cords periodically and replace of damaged.
* Inspect tool cords periodically, if the tool got damaged, please contact our authorized

service personnel.

1

SS-621Series User’s Manual 使用說明書

* When using the tool outdoors, only employ extension cords intended for use outdoors

and marked "W-A"

* When working on small or irregular shaped objects, secure with vise or clamps.
* Disconnect the tool when not in use. Avoid unintentional starting. lf the gun shuts down

during operating, disconnect from the power supply and have gun serviced by authorized
service personnel.

* To be on the alert! Please pay attention to the work and use common sense when

operating this tool. Do not operate the tool when you are tired or taking medication or
drugs that make you drowsy.

WHEN REMOVING PAINT OR VARNISH

* Never use the heat gun in combination with chemical scrapers.
* Clean dry paint or varnish from the nozzle and scrapers after use. It could ignite.
* Use in well-ventilated areas only. Peelings and residue from lead-based paints are

poisonous.

POWER INFORMATION

Be sure the power supply you are using agrees with the nameplate marking on the heat
gun, the guns are designed to run on 220 V 50 Hz, alternating current (ordinary house
current). Voltage decreases more than 10% can cause loss of power and possible
overheating. The tool is double insulated for safety. This means there are two separate
layers of insulation between the operator and the tool's electrical system.

Warning
operating the heat gun. Double insulation acts as a safeguard against injury resulting from
a possible electrical insulation failure inside the tool. Tools built with double insulation are
not intended to be grounded. Because of this, the gun's power cord is fitted with a
two-pronged plug suitable for use in any conventional 220 volt electrical outlet. Additional
ground connections need not be made.

Warning
Replace damaged cords.

LCD Panel

1. Temperature adjust (-) from 100℃~650℃

2. Air volume adjustment 166L, 330L, 500L / min

3. Temperature adjust (+) from 100℃~650℃

USING HEAT GUN

The heat gun is light and easy to use. The variable heat
control allows from low to high working temperature settings as well as an off setting. The
low setting is roughly 100℃. and the high setting is roughly 650℃ (Adjustable Temp. 100
℃-650℃.for Electronic Model).
Before pl
position. When ready to begin work, set power switch to on, and set variable heat control to

: double insulation does not take the place of normal safety precautions when

: when servicing double-insulated tools, use only identical replacement parts.

ugging into the electrical outlet, always make certain the power switch is in the off

2

SS-621Series User’s Manual 使用說明書