Pro Series 1370600 User Manual [en, es, fr]
ITEM
1370600
:
DESCRIPTION
Trunk Mount 3 Bike Carrier
:
Kit Contents:
Main Support Assembly 1 Side Cam Buckle Straps 2
Upper Support Tube 1 Trunk Hook 2
Lower Support Tube 1 Adjustment Knobs 4
Upper / Lower Hook Straps 4 ¼-20 x 1 ½ Carriage Bolt 8
Cradle Strap 6 ¼-20 Lock Nut 4
Assembly Instructions:
1. Align mounting holes of upper support tube with holes in main support assembly. Use a supplied ¼
carriage bolt and ¼ Nylon locking nut to fasten upper support tube to main support. DO NOT OVER
TIGHTEN. Support tube must be able to rotate freely. (Fig 1)
2. Align mounting holes in upper support tube with adjustment slot in main support assemble. Use a
supplied ¼ carriage bolt and adjustment knob, to fasten tube to main support. (Fig 1)
3. Repeat steps 1 & 2 for lower support tube.
4. Pass side cam buckle straps through side strap slots on main support assembly side brackets and
through slot on trunk hook. (Fig 3)
5. Thread upper / lower hook straps through cam buckles of main support assembly. (Fig 2)
Adjustment Knob
¼ Carriage Bolt
¼ Nylon Lock Nut
Upper Support Tube
¼ Carriage Bolt
FIGURE 1
Cequent Performance Products
47774 Anchor Court
Plymouth, MI 48170
Technical Service: (888) 521-0510
Lower Support Tube
Page 1 of 12
Main Support Assembly
¼ Carriage Bolt
1370600N Rev A 09-09
Printed in Taiwan
Adjustment Knob
ITEM
1370600
:
Trunk Mount 3 Bike Carrier
:
SIDE STRAPS
FIGURE 3
UPPER / LOWER
HOOK STRAPS
DESCRIPTION
FIGURE 2
Mounting Rack to Vehicle:
1. Loosen lower support tube adjustment knobs and rotate lower support tube to open position. Tighten
adjustment knobs.
2. Rest lower support tube on vehicle bumper, on vehicle license plate, or a vertical portion of trunk or
hatch. Find most solid position as possible. DO NOT rest against glass, plastic bumper without
support, vehicle badges, or thin flexible sheet metal.
3. Loosen upper support tube adjustment knobs and rotate upper support tube so that it contacts vehicle.
Main support assembly arms should be at a slight angle upwards (10 -20 deg) Tighten adjustment
knobs.
4. Attach upper hook straps to top edge of trunk or hatch. If a spoiler is present, straps should be routed
under spoiler if possible. Never attach to glass, plastic or trim.
5. Attach lower hook straps to bottom edge of trunk or hatch. Ensure strap is not close to vehicle
exhaust.
6. Center rack on vehicle and slowly tighten each strap evenly, alternating as you tighten (top left, lower
right, lower left, top right).
7. Attach side strap hooks to side edge of trunk or hatch. Evenly tighten, alternating from side to side.
Cequent Performance Products
47774 Anchor Court
Plymouth, MI 48170
Technical Service: (888) 521-0510
Page 2 of 12
FIGURE 4
1370600N Rev A 09-09
Printed in Taiwan
ITEM
1370600
:
DESCRIPTION
Trunk Mount 3 Bike Carrier
:
Bicycle Loading:
1. Load first bike so that the gears and de-railer are facing away from the vehicle. Load so that the top
tube of the bicycle rest on the rack cradles.
2. Use a cradle strap through cradles and over top tube of bicycle. Secure by pressing hook and loop
together. Check to ensure bicycle is secure and unable to jump out of cradle.
3. Load additional bicycles as describe in step 1 & 2, alternating the direction of each.
4. Bicycles should be loaded with heavier bicycles closest to vehicle.
CRADLE STRAP
FIGURE 5
FIGURE 6
Cequent Performance Products
47774 Anchor Court
Plymouth, MI 48170
Technical Service: (888) 521-0510
Page 3 of 12
1370600N Rev A 09-09
Printed in Taiwan
ITEM
1370600
:
DESCRIPTION
IMPORTANT NOTES:
• This bicycle rack has been designed to carry up to three (3)bikes, as long as the maximum weight on the
rack does not exceed 40 kgs or 90 lbs.
• Vehicles with a severely curved trunk or hatch along the top edge should not use this rack. Straps could
slide to the side, causing your rack and bicycles to fall from the vehicle.
• Always check tie down and hook and loop straps for tightness prior to each trip.
• Replace straps if they appear worn or frayed.
• Proper fitting and installation of this carrier to your specific vehicle is critical, and is the owner’s sole
responsibility.
• Improper use of this product may result in damage to your vehicle, your bicycles, or even other
vehicles driving behind you (as a result of colliding with or trying to avoid fallen bicycles and/or the rack).
• When leaving the bike carrier outside for extended periods of time the finish will lose its luster. It is
recommended that when not in use the rack is stored indoors.
• Take care to add padding on any area of the bikes that touches another bike or any part of the vehicle.
Damage can and will happen (to your bikes and/or to the vehicle) if care is not taken during the loading and
transporting of your bikes, and padding used where necessary.
• Bicycle tires should be kept at least 6” away from the exhaust pipes of the vehicle. The high temperature
exhaust exiting from the exhaust pipes is hot enough to melt or damage tires. Keep all bike tires totally
away from the direct exhaust flow.
• Bikes fitted with large accessories (such as child carrying seat) will greatly increase the possibility of
interference with mounting to the rack on the vehicle.
• After reading this manual, should you have any additional questions regarding the compatibility, fitting and/or
use of this rack, please call your nearest ProSeries® authorized retail dealer or Cequent Technical Service.
Trunk Mount 3 Bike Carrier
:
WARNING:
• DO NOT USE THIS BIKE CARRIER ON A TRAILER OR 5thWHEEL R.V.
• Improper mounting will void the rack warranty.
• Damage to bicycles or rack due to ground clearance problems are not covered by warranty.
• Not for off road use.
Cequent Performance Products
47774 Anchor Court
Plymouth, MI 48170
Technical Service: (888) 521-0510
Page 4 of 12
1370600N Rev A 09-09
Printed in Taiwan
Loading...