ProSense XTP-160-N40140F, XTP-260-N40140F, XTP-360-N40140F, XTP25N-030-N40140F, XTP25N-050-N40140F Installation Instructions

...

Download

XTP product insert Rev. 2

71485817

XTP/XTPS Series Temperature Transmitter Probes and

RTD1/RTD1-S Series Temperature Sensors

Installation Instructions

(XTPS/RTD1-S)

Part Number Measuring Range* Process Connection Length Output

XTP-160-N40140F XTP-260-N40140F XTP-360-N40140F XTP25N-030-N40140F XTP25N-050-N40140F XTP25N-100-N40140F XTP25N-150-N40140F XTP50N-030-N40140F XTP50N-050-N40140F XTP50N-100-N40140F XTP50N-150-N40140F XTP-160-0300F XTP-260-0300F XTP-360-0300F XTP25N-030-0300F XTP25N-050-0300F XTP25N-100-0300F XTP25N-150-0300F XTP50N-030-0300F XTP50N-050-0300F XTP50N-100-0300F XTP50N-150-0300F XTP-160-0100C XTP-260-0100C XTP-360-0100C XTP25N-030-0100C XTP25N-050-0100C XTP25N-100-0100C XTP25N-150-0100C XTP50N-030-0100C XTP50N-050-0100C XTP50N-100-0100C XTP50N-150-0100C XTPS15-030-0300F XTPS15-050-0300F XTPS15-100-0300F XTPS15-150-0300F

XTP product insert Rev. 2

-40 to 140°F (-40 to 60°C)

0 to 300°F (-17.8 to 148.9°C)

0 to 100°C (32 to 212°F)

0 to 300°F (-17.8 to 148.9°C) 1.5” Sanitary Tri-Clamp (3-A)

* Transmitter probes are factory configured and ready for use out of the box. If changes are desired,

transmitter probes can be re-configured. See Programming section of these instructions.

None, use compression fitting

1/4” male NPT

1/2” male NPT

None, use compression fitting

1/4” male NPT

1/2” male NPT

None, use compression fitting

1/4” male NPT

1/2” male NPT

160mm 260mm 360mm

30mm

50mm 100mm 150mm

30mm

50mm 100mm 150mm 160mm 260mm 360mm

30mm

50mm 100mm 150mm

30mm

50mm 100mm 150mm 160mm 260mm 360mm

30mm

50mm 100mm 150mm

30mm

50mm 100mm 150mm

30mm

50mm 100mm 150mm

4-20mA

XTP and XTPS Series ProSense Temperature Transmitter Probes

Part Number Measuring Range Process Connection Length Output

A Medium water at T = 50 °C (122 °F)

v (ft/s)

v (m/s)

RTD1-25N-030-H RTD1-25N-050-H RTD1-25N-100-H

1/4” male NPT

RTD1-25N-150-H RTD1-50N-030-H RTD1-50N-050-H RTD1-50N-100-H

-58 to 302 °F (-50 to 150 °C)

1/2” male NPT

RTD1-50N-150-H RTD1-S15-030-H RTD1-S15-050-H RTD1-S15-100-H

1.5” Sanitary Tri-Clamp (3-A)

RTD1-S15-150-H

Temperature limits

Max. Ambient

Temperature

Up to 77°F (25°C) 302°F (150°C) Up to 104°F (40°C) 275°F (135°C) Up to 140°F (60°C) 248°F (120°C) Up to 185°F (85°C) 212°F (100°C)

Max. Process

Temperature

Process pressure limits

With or without NPT process connection

• 1450 psig (100bar) maximum

Note: Working pressure when using

compression fitting should not exceed the fittings rated pressure.

With Sanitary Tri-clamp process connection

• 232 psig (16bar) maximum

XTP product insert Rev. 2

Maximum flow velocity based on insertion length

135

120

105

L Insertion length, during ow v Flow velocity

0306090120 150 180 210 240 270 300

012345 78 910

L (mm)

L (in)

30mm

50mm

100mm

150mm

30mm

50mm

100mm

150mm

30mm

50mm

100mm

150mm

RTD1 and RTD1-S Series ProSense Temperature Sensor Probes

RTD Pt100

Class A

3-wire

Installation

1 Safety Instructions

1.1 Designated use

• The device is a compact temperature transmitter probe for the acquisition and conversion of temperature input signals for industrial temperature measurement.

1.2 Installation, commissioning, operation

• The device must only be installed, connected and commissioned by qualiﬁed and authorized staff (e.g. electrical technicians) strictly adhering to the instructions contained in this manual, the applicable norms, legal regulations and certiﬁcates (depending on the application).

• These authorized staff members must have read and understood this manual and follow the instructions it contains.

• Damaged devices must not be put into operation and they must be labeled as defective.

1.3 Operational safety

• The device is safely built and tested according to state-of-the-art technology and has left the factory in perfect condition in regards to technical safety. The applicable regulations and European standards have been taken into account.

• Please observe the technical data on the nameplate!

• The device must only be powered by a power supply unit with a limited energy electric circuit in accordance with IEC 31010-1: “SELV or Class 2 circuit”.

• Due to its design, the device is not repairable. When later disposing of the device, please observe local regulations.

XTP product insert Rev. 2

A B

Pipe installation

• A: On angle brackets

• B: In smaller pipes, inclined

• C: Perpendicular to the direction of ﬂow (hygienic installation 3° minimum inclination required for inlet to self drain)

• L = Insertion Length

1. For NPT and compression ﬁttings, seal the process

connection with Teﬂon tape before you screw in the device.

2. Ensure that the hygienic process connection and any

connection adapters can withstand the maximum process pressure.

3. Install the device before the process

application is started.

Minimum insertion length

Lmin = 30mm (1.18 in)

3°

Dimensions

Ø18.0

Ø50.4

mm [inches]

[Ø0.71]

[Ø1.98]

XTP

RTD

62.5

36.5

[2.46]

[1.44]

XTP25/RTD1-25N Series

NPT Units

Dimensions

A B

30mm [1.18 in] 101mm [3.98 in]

50mm [1.97 in] 121mm [4.76 in]

100mm [3.94 in] 171mm [6.73 in]

150mm [5.91 in] 221mm [8.70 in]

XTP product insert Rev. 2

XTP

RTD

60.1

36.5

[2.37]

[1.44]

XTP50/RTD1-50N Series

NPT Units

M12

62.0

[2.44]

Ø6.0

[Ø0.24]

XTP Series

Compression Units

Dimensions

A B

160mm [6.30 in] 222mm [8.74 in]

260mm [10.24 in] 322mm [12.67 in]

360mm [14.17 in] 422mm [16.61 in]

M12

66.0

[2.60]

Ø6.0

[Ø0.24]

XTPS Series

3-A Sanitary Units

Dimensions

A B

30mm [1.18 in] 96mm [3.78 in]

50mm [1.97 in] 116mm [4.57 in]

100mm [3.94 in] 166mm [6.54 in]

150mm [5.91 in] 216mm [8.50 in]

M12

44.0

[1.73]

Ø6.0

[Ø0.24]

RTD1-S15 Series

3-A Sanitary Units

Dimensions

A B

30mm [1.18 in] 74mm [2.91 in]

50mm [1.97 in] 94mm [3.70 in]

100mm [3.94 in] 144mm [5.67 in]

150mm [5.91 in] 194mm [7.64 in]

Wiring

Supply Voltage (VDC)

Hygienic applications: Electrical connection cables must comply with 3-A sanitary standard, must be smooth, corrosion resistant and cleanable.

XTP and XTPS Wiring (4-20 mA)

1 (BN) + 2 (WH) nc 3 (BU) 4 (BK) nc

M12x1

3 0 V (4-20 mA)

Load Impedance

1086

Load ( )

Operating Region

35 V10 V

10...35 VDC (4-20 mA)

Note: Wiring colors are based on AutomationDirect

CD12L and CD12M 4-pole cable assemblies.

Sinking Load

Load

Sourcing Load

Load

- -

POWER SUPPLY

POWER

SUPPLY

XTP product insert Rev. 2

RLmax = (V

powersupply

-10V) / 0.023 A (current output)

e.g. (24V - 10V) / 0.023A = 608Ω

RTD1 Wiring (3-wire Pt100 RTD)

1 (BN) nc 2 (WH) + 3 (BU) 4 (BK) -

N/C

To prevent damage to the device do not overtighten the M12 plug

XTPS Series

Programming (XTP and XTPS units only)

Transmitter probes are factory configured and ready for use out of the box. If changes are desired,

transmitter probes can be re-configured using the XT-SOFT programming software, available as a free download at www.automationdirect.com, an XT-USB configuration cable and an XT-M12 adapter (purchased separately).

Settable Parameters

Standard Settings

Expanded Settings

Service Functions

Measuring unit °C/°F Part number dependent Measuring range (start and end values) -50 to 150°C (-58 to 302°F) maximum range Part number dependent Fault condition reaction ≤ 3.6 mA or ≥ 21.0 mA ≥ 21mA Output 4-20 mA or 20-4 mA 4-20 mA Filter 0...8s 0s Offset -9.9 to +9.9°C (-17.8 to 17.8°F) 0.0 Measurement point identification/TAG 8 alpha-numeric digits Test Password (Release Code) 4 numeric digits 0000 Output simulation drives output to a

fixed value

on/off off

XT-SOFT PC Configuration Software

XT-USB Conguration Cable

XT-M12 Adapter

Note: XT-SOFT version 1.27.13.0 or later required for use with the XTP or XTPS series transmitters

Factory Settings

XTP product insert Rev. 2

71485817

XTP or

Powered from USB port

ProSense XTP-160-N40140F, XTP-260-N40140F, XTP-360-N40140F, XTP25N-030-N40140F, XTP25N-050-N40140F Installation Instructions

Specifications and Main Features

Frequently Asked Questions

User Manual