ProScan PSVR85, Plus Silver PSVR85 User Manual

VCR

USER'S MANUAL

¸%¸,¸

• /

<

PROSCAN

_ ii _¸¸¸¸

• ,q

'k

MODEL PSVR85

WARNING

To reduce risk of fire or
shock hazard, do not
expose this product to

rain or moisture.

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

A his symbol indicates important A

instructions accompanying the
product.

This symbol indicates "dangerous
voltage" inside the product that presents
a risk of electric shock or personal injury.

Cautions

Caution: To prevent electric shock, match wide blade of plug to wide slot, fully insert.
Attention: Pour _viter les chocs 61ectriques, introduire la lame la plus large de la fiche dans

(a borne correspondante de Laprise et pousser jusq_ au fond.

Refer to the identification/rating label located on the back panel of your product for its
proper operating voltage.

FCC Regulations state that unauthorized changes or modifications to this equipment may
void the user's authority to operate it.

Cable TV Installer: This reminder is provided to call your attention to Article 820-40 of the

National Electrical Code (Section 54 of the Canadian Electrical Code, Part t ) which

provides guidelines for proper grounding and, in particular, specifies that the cable ground

sharl be connected to the grounding system of the building as close to the point of cable

entry as practical.

Care and Cleaning:

Use a soft cloth or the dusting attachment of your vacuum cleaner to dust your VCR.
Remove dust from the ventilation holes.

Plastic surfaces are easily scratched and can be marred by alcohol and various solvents.
Avoid excessive use of oil-based furniture polishes since the materials used in the cabinet

will accumulate more dust. A nonabrasive, antistatic cleaner/polisher is recommended.

Product Registration

Please fill out the product registration card and return it immediately. Returning the card allows us to contact you if needed.
Keep your sales receipt to obtain warranty parts and service and for proof of purchase• Attach it here and record the serial and model

numbers in case you need them. The numbers are located on the back of the product.
Model No. PSVR85

Serial No.

Purchase Date:

Dealer/Address/Phone:

VCR Plus+system and PlusCodeare registered trademarks o( Gemstar Oevelopmenl Corporation.
TheVCR Plus+ Systemis manufactured underthe licensefrom GemstarDevelopment Corporation.

COMMERCIAL ADVANCE and MOVIE ADVANCE are registered trademarksof SRI,, Inc.;a JerryIggulden invention licensed in association with Arthur D. Little Enterprises.

First Things First ................................................................................... 3

Using the QuickSet Guide ...................................................................5

Setting Up theVCR ............................................................................. 7

Usingthe Menus to SetUp Features................................................8

Language.............................................................................................8

Cable Box Setup...............................................................................9

VCR Channels List.........................................................................I0

Auto Channel Searching.........................................................I0

Changingthe SignalType.........................................................II

Adding or Removing Channels..............................................12

Time and Date ................................................................................12

Auto Clock Set Feature..........................................................12

SettingtheTime Zone ........................................................13

SettingDaylightSavings......................................................13

SettingTime and Date ManuaUly............................................14

VCR Plus+SILVER Programming System .................................15

MappingVCR Plus+System Channels Manually................16

AdditionalSetUp Featuresinthe PreferencesMenu ............18

Remote VCR I/VCR2 Option .................................................IB

Auto Play .................................................................................... 19

AutoTVIVCR ............................................................................19

EnergySaver ................................................................................19

Front Panel Brightness (VCR Display) .................................20

Tape Speed .................................................................................20

Set Auto Repeat ........................................................................ 20

VCR Basics .............................................................................................. 23

Remote Buttons ...................................................................................24

Component Buttons .....................................................................24

VCR Function Buttons ..................................................................25

TV Function Buttons .....................................................................26

Playing aTape ........................................................................................7-7

Recording ..............................................................................................28

Recording .................................................................................................29

Recording Features .............................................................................30

Express Recording (XPR) .............................................................30

Program Express ............................................................................3 I

Timer Recording ............................................................................3 I

Timer RecordingWith theVCR Plus+ System ..................33

Setting Up the Channel List ..............................................33

Using theVCR Plus+ Programming System ...................33

Stopping aTimer Recording ...................................................35

Reviewing and Clearing Programs ........................................35

Editing aTimer Program .........................................................35

Recording Broadcast Stereo TV or SAP

(Second Audio Program) ..........................................................36

Recording Audio Only ...................................................................36

Using Two VCRs for Copying and Editing Tapes ......................37

Using Dual Remote with AutoEdit .............................................38

Program The Remote ......................................................................39

Testing the Remote .............................................................................40

Programming the Remote to Control aTV,

Satellite Receiver, or Cable Box ...................................................40

Using Direct Entry ......................................................................:..4 I

To Control anAuxiliary Component ..............................................42

Other Features ....................................................................................45

Commercial Advance ......................................:...................................46

Marking .............................................................................................47

Playback ............................................................................................48

Display ..............................................................................................48

Movie Advance .....................................................................................49

Picture Search Options ......................................................................5 I

Forward and Reverse Search .......................................................51

Slow Motion ....................................................................................5 I

Frame Advance ...............................................................................52

Variable Speed Using the Shuttle Ring .................................52

Index Search ....................................................................................53

Go-To Search ..................................................................................53

Pro-Tect PlusTM Locking Feature ......................................................54

Tracking ..................................................................................................54

Time Counter .......................................................................................55

Audio Set-Up Features .......................................................................56

Tape Playback ........................................................................................57

Connections ...........................................................................................59

Connecting¥our VCR .........................................................................60

Jacks and Cables .............................................................................60

RF Jacks and Antenna Cables (F-type) .................................60

Audio/video Jacks and Cables (RCA-type) ........................60

Choosing aVCR Connection ......................................................61

Advantages of Audio/video Cable Connections ...............61

"l'VWith RF Jack Only .............................................................62

TV With Audio/Video Jacks....................................................63

-iV With Audio/Video Jacks and Cable Box .......................64

TV With RF Jack and Satellite Receiver ...............................65

TV With Audio/Video Jacks and Satellite Receiver ...........66

Reference .................................................................................................67

Front Panel ............................................................................................68

Display Panel .........................................................................................69

Back Panel .............................................................................................70

Questions and Answers About Commercial Advance .................7 I

TroubleshootingTips ...........................................................................72

How to FindYour'FV'sVideo Input Channel .................................75

Specifications ........................................................................................76

Cleaning theVCR .................................................................................76

Limited Warranty .................................................................................77

Glossary .................................................................................................78

Index .......................................................................................................79

2

WELCOME TO YOUR

NEW VCR...

To help you get started using yourVCR with as

little reading as possible, we've put all the basic
information needed in the first three sections.To

help you along, there's even a QuickSet Guide
which walks you through several setup steps at

once.

I 1 FIRST THINGS FIRST

V

V

GETTING STARTED

Before this first step, though, learning about
the time and date, your remote control's features,
working with channels, and basic video tape

operations are essential to get all you can out of

theVCR. Once you are comfortable with these

features, feel free to refer to other sections

because they cover the more detailed information.

V

V

WHAT REMAINS?

The final sections of this manual contain playback

and recording information, a detailed connections
section, and a reference section including
troubleshooting tips, warranty information, and an

index.

V

¥

V

I READ ME!

These note boxes give you tips for
your new video cassette recorder.

3

STEP 1: WHAT'S IN THE BOX?

The following items come packed in the box:

• VCR

• Remote control

• RF coaxial cable

STEP 2: INSTALL BATTERIES IN
THE REMOTE CONTROL

Follow these steps whenever you need to install or change the
batteries in your VCR's remote.

1. Remove the cover of the battery compartment.

2. Place the batteries into the remote's back panel. Match the
positive (+) and negative (-) ends of each battery to the

diagram inside the battery compartment.

3. Replace the cover.

! _.,ii

,."._i

, *,+Q 4,

STEP 3: CONNECT YOUR VCR

If you connect your VCR to your home antenna or cable system
and then to your TV, use the VCR's ANT. IN and RF OUT jacks

for a good signal as shown to the right.

If you have a TV with AUDIO/VIDEO jacks, use the jacks for a
better connection. Refer to the section, Connections, toward

the back of the manual, for additional connection options.

STEP 4: PLUG IN THE VCR

Your VCR's power cord has a plastic band strung through the
blades. Remove plastic band before plugging the cord into the

power outlet. To remove band, cut with a pair of scissors and
pull it free of the blades. Once the plastic is removed, match the

wide blade of the power cord to the wide slot in the AC outlet.

Be sure to insert the plug completely.

Coaxial Connection

CABLE,CABLEBOX,OR ANTENNA

VCR

_F

,o,N

4

STEP 5: TUNE THE TV

Tune the TV to the VCR viewing channel. The VCR viewing
channel is channel 3 or 4 or the TV's video input.

If you connect your VCR using the ANT. IN and RF OUT
jacks with RF coaxial cable, set the 3 CH 4 switch to
channel 3 or channel 4--the channel you want to use on
your TV.

If you connect your VCR using the AUDIO/VIDEO jacks

with audio/video cables, select the TV's video input with

the remote's TV and INPUT buttons to see the signal. For

more information see "How to Find Your TV's Video Input

Channel" in the References section of this manual.

STEP 6: TURN ON THE VCR

Press ON - OFF on the VCR's front panel or VCR1 on the
remote control to turn on the VCR. The first time you turn the
VCR on, a menu screen appears. This is the start of a QuickSet
Guide which helps you pick different options for your VCR.

STEP 7: USING THE

QUICKSET GUIDE

The QuickSet Guide is an automated procedure that helps you

set up your VCR. The first time you turn on your VCR, the first

screen of the Guide appears.

Select a language.

ChoJslssez une Langue.

ii im

EspaEol

Francals

1. Press 1 for English, 2 for Espaffol (Spanish), or 3 for Fran_:ais
(French).

The remaining menus throughout the set up will appear in the

chosen language. Just follow the step-by-step procedures until

the interactive setup is complete.

(Continue5 on next page)

VCRYiewing Channel
When using the ANTENNA jacks

to connect yourVCR, tune yourTV
to channel 3 or 4.

When using the audio/video jacks
to connect yourVCR, tune yourTV

to theTV's video input.

QuickSet Guide

If you choose not to use the

QuickSet Guide to set up theVCR,
you can exit now and return to the

Guide through Setup in theVCR
HAIN MENU.

1

5

((]mlinued troth plevitlus IJ, l_l'l

if the menu does not appear:

• Make sure theIV is tuned to the same channel as the 3 CH
4 switch or the ]V's video input "channel" (see "How to

Find Your lV's Video Input Channel" in the References
section of this manual for more information).

• Make sure the VCR indicator is on in the VCR display if you
connected your VCR using the ANT. IN and RF OUT jacks.

• Check your corlnections.

If you choose li) set up your VCR options individually rather

than setting them up in the QuickSet Guide, then go to the next

section.

STEP 8: ACCESS THE MENUS

The MENU and number buttons let you access, select, and
change the VCR's display preferences. For example, to select a

different preferred omscleen language than the one selected
during tile initial set up, do the following;

I. Press MENU to display tire VCR MAIN MENU.

VCR MAIN MENU

I NCR Plus÷

2 Timer Recordings
3 Time
4 Channels

5 Setup

6 Preferences

7 Audio

ulllml

0 Exit

2. Press 8 to display the LANGUAGE menu.

LANGUAGE

Select a language.

2 Espafi_l

3 Fran_ais

Press MENU to continue

3. Using the remote control, press 1 for English, 2 for Espafiol
(Spanish), or 3 for Fransais (French).

All other on-screen menus are worked in similar ways; using the
remote control lo follow on-screen instructions. See the next

section, Additional Set-Up Features, for detailed information
about accessing menus.

Using the Arrow Buttons

Use the menu, arrow and OK
buttons on the remote control to

access and select menu items.

GUIDE INFO

MENU CLEAR

Pressing the MENU button will

bring up the Main Menu. When
menus are displayed, you can
either select the item you want by
pressing the same number button

on the remote, or by using the up

and down arrows to scroll through

items highlighting them. If you

scroll through menu items, you

must press the OK button to

select it.

You also set some of theVCR's

features (e.g., setting the clock)

using the on-screen displays and

the remote control arrow buttons

in this way.

You also use the left and right

arrows when setting up a timer

program.These buttons move

from one location to another, such

as moving from hours to minutes.

6

SETUP FEATURES

Below is a list of features that need to be set up to get

the most out of yourVCR. Many of these menus are
covered during the QuickSet Guide, but if you ever

want to change a menu, refer to this section.

Language Selection

Cable Box Set Up

VCR Channel List Set Up
(Auto Channel Search)

Time Zone and Daylight Savings
(Auto Clock)

Manually SettingTime and Date

VCR Plus+ System Channels

Remote VCR I/VCR2 Feature

2

Y

SETTING UP THE VCR

Y

V

Y

Auto Play*

Auto TV/VCR*

Y

EnergySaver*

Front Panel Brightness*

Preferred Tape Speed*

Y

Y

* Items NOT set up during the QuickSet first-time setup and musl be set manuall)_

7

USING THE MENUS TO SET

UP FEATURES

You set up features by using the menu system as discussed in
the previous section. Each feature that appears in the QuickSet

Guide is exp(ained in this section as well as a few other features
you should set up before you begin using your VCR.

LANGUAGE

Selecting your preferred language determines how the on-
screen displays will appear. To change the language:

1. Press MENU to display the VCR MAIN MENU.

VCR MAIN MENU

I VCR Plus+
2 Timer Recordings
3 Time

4 Channels
5 Setup

6 Preferences
7 Audio

0 Exit

2. Select 8 to chose the LANGUAGE menu.

LANGUAGE

SeLect a Language.

L

2 EspaBot

3 Fran_ais

Press MENU to continue

3. Select English, Espaffol (Spanish), or Fran(;ais (French).

Is Something Missing?

Not all the VCR screens are shown

in this manual when explaining the
features.

8

CABLE BOX SETUP

This setup applies only when all channels are received through
the cable box.

1." Press MENU to display the VCR MAIN MENU.

VCR MAIN MENU

I VCR PLus+
2 Timer Recordings

3 Time

5 Setup
6 Preferences

7 Audio

8 Language

0 Exit

2. Press 4 to display the CHANNELS menu.

CHANNELS

1 Auto Channel Search
2 Add/Remove Channels

3 Signal Type: CABLE
6 VCN Plus+ Setuo

I

0 Exit

3. Press5 todisplaytheCABLE BOX SETUP menu. Then select
one of the threechoices.

,

CABLE BOX SETUP

Do you use your cable
box to receive ALL

channels or only SOME

channels?

2 Only SOME channels

3 Cancel setup

If you selected ALL channels, enter the output channel of

your cable box, usually 03, 04, or Video line input and
press MENU.

CABLE BOX SETUP

On what channel does
the VER receive signals

from the cable box?

(usuaLly 3, 4, or Video)

Enter 01-13 or INPUT
Press MENU to cancel

Make sure you enter a "0" before entering single-digit
numbers. To select Video Input, press the INPUT button on

the remote.

(Continueson nextpage)

Cable Box Setup

ALL channels: enter two numbers
for output channel of your cable

box or press INPUT forVideo

Input.

Only SOME channels: if you only

use the cable box to tune premium
channels.

Cancel setup: select to cancel.

W

9

I( I*tltltlllt'l/ hlllll prl'viou_ /J,l_I')

CABLE BOX SETUP

"he VCR will now

receive all signals
from the cable box

on channel 04.

Press MENU to continue

Once you complete the setup, the on-screen menus confirm
that the VCR will re/eive all signals on the designated

channel.

VCR CHANNELS LIST

If you use a cable box for all channels, this step is not necessary.

Your VCR may come with a channel list preset at the factory.

Even though your VCR may come with such a list, it's possible

that you will want to add or delete certain channels depending

on whether they are active.

AUTO CHANNEL SEARCHING

1. Press MENU to display the VCR MAIN MENU.

VCR MAIN MENU

1 VCR PLus+
2 Timer Recordings

3 Time

|

5 Setup
6 Preferences

7 Audio

8 Language
Q Exit

2. Press 4 to display the CHANNELS menu.

3,

CHANNELS

2 Add/Remove Channels

3 Signal Type: CABLE
4 VCR Plus+ Setup

5 Cable Box Setup

0 Exit

Press 1 to display the AUTO CHANNEL SEARCH menu.

Auto Channel Search

Use the Auto Channel Search
feature to place all available

channels in memory.
If you ever change cable or

antenna signals, you may need to
Auto Channel Search again.

10

AUTO CHANNEL SEARCH

What type of signal

are you using?

1 Cable TV

2 Antenna

0 Cancel

4. Select one of the three AUTO CHANNEL SEARCH options.

• Cable TVsearches for cable stations fronl a single channel

• Antenna searches for local broadcast stations on all channels

• Detect Automaticallywi[I make this decision for you

AUTO CHANNEL SEARCH

Now scanning channel 14

Press any key to cancel

The VCR begins scanning for the available channels--this
takes about one to two minutes. When the scan is complete,

the VCR tunes to the lowest channel number available. At
this point, pressing CHAN + or - on the remote should only

select active channels.

Detect Automatically

A strong cable or antenna signal

in your area may cause Auto
Detect to mis-detect. If this

should happen, select I or 2 for
the system you have.

1

CHANGING THE SIGNAL TYPE
This feature is useful if your cable signal goes out; it allows you

to switch to a regular antenna for alternate television reception.

1. Press MENU to display the VCR MAIN MENU.

2. Press 4 to display the CHANNELS menu.

3. Press 3 to change the Signal Type between Cable and
Antenna. When you are finished, press 0 to exit back to the
Main Menu and 0 again to exit to normal viewing.

11

ADDING OR REMOVING CHANNELS

You may want to add or remove channels after you auto
channel search, especially if channels have weak signals or
content you don't want to watch. To achieve this:

1. Press MENU to display the VCR MAIN MENU

2. Press 4 to display the CHANNELS menu

3. Press 2 to display the ADD/REMOVE CHANNELS screen.
Use the CHANNEL + or - buttons on the remote or enter a

specific channel number with the number buttons to go to
the channel you want to add or remove.

u,

r

Selecting Channels
The CHANNEL + and - buttons

access those channels which are
active in yourVCR channel list.

You can still access channels not in

the channel list by using the
number buttons on the remote.

ADD/REMOVE CHANNELS

Channel 115

_s presently ADDED

Press CLEAR to remove
Press MENU to exit

ADD/REMOVE CHANNELS

Channel 115
is presently REMOVED

Press INFO to add
Press RENU to exit

Once you have reached your selection, the screen will tell

you if the channel is currently in your viewing list. Press

CLEAR to remove a channel. Press INFO to add a channel.
Once you are completed, you can press MENU to exit out of

the menus.

TIME AND DATE

The VCR gives you two ways to set the time and date; manually
and the Auto Clock feature. Using Auto Clock enabSes the VCR
to update the clock each time you turn off the VCR. The Auto
Clock feature updates the time for you automatically if your

local broadcasts offer AlISet time data.
If for any reason ti.me information cannot be automatically

downloaded, time and date information can always be entered
manually by using the on-screen displays.

AUTO CLOCK SET FEATURE

The Auto Clock feature is set to ON by default at the factory. In
the ON setting, the VCR looks for a channel carrying AIISet data

and updates the clock using the Coordinated Universal Time.
There are certain steps which are required, such as Auto
Channel Search, setting the time zone, and setting the daylight-
saving feature, before the Auto Clock feature works.

Auto Clock Info

With a cable box, theVCR will not
reset the clock after a power

outage unless the cable box is set
to the channel carrying the
broadcast signal.

If Auto Clock Set is unsuccessful,

try tuning theVCR (or cable box)
to a channel carrying AIISet time

information (usually PBS), then

turn theVCR off. If the time does

not set within I0 minutes, set the
time and date manually through

theTime menu.
Check local cable system orTV

stations for availability of channels
with AIISet information.

12

SETTING THE TIME ZONE

1. Press MENU to display the VCR MAIN MENU.

VCR MAIN MENU

1 VCR PLus+

; Timer Recordinls

4 Channels
5 Setup

6 Preferences
7 Audio

8 Language
0 Exit

2. Press 3 to display the TIME menu.

TIME

1 Set Time and Date
2 Auto Clock Set: ON

4 Set Daylight Savings

0 Exit

3. Press3 to displaytheSET TIME ZONE screen,

SET TIME ZONE

What is your Time Zone?

1 Eastern
2 Central

3 Mountain

4 Pacific
5 Alaska

6 Hawaii

Press MENU to continue

.

Select your time zone.

If you select Automatic for your time zone, the VCR sets the

clock using the first Coordinated Universal Time information

it finds. If the time is not correct, select another time zone or

set the time and date through the menu system.

SETTING DAYLIGHT SAVINGS

1. Press MENU to display the VCR MAIN MENU.

VCR MAIM MENU

1 VER PLus+

2 Timer Recordinls

4 Channels

5 Setup

6 Preferences

7 Audio
8 Language
0 Exit

13

2. Press 3 to display the TIME menu.

TIME

1 Set Time and Date
2 Auto CLock Set: ON
3 Set Time Zone

] _irJl4.11HIalLillRli_..ILYliinlltl.a.* .

0 Exit

3. Press 4 to display the SET DAYLIGHT SAVINGS menu.

SET DAYLIGHT SAVINGS

Does your area observe
Daylight Savings Time

from April to October?

I Yes, DST is observed
2 NO

Press MENU to continue

4. Select one of the options.

• DST stands for Daylight Savings Time.

• If you choose Automatic, the VCR sets the clock using the
DST information broadcast in the signal (channel).

SETTING TIME AND DATE MANUALLY
If the Auto Clock Set was unsuccessful, set the clock through the

TIME menu option. The Auto Clock Set feature is set to OFF
automatically when you set the clock this way.

1. Press MENU to display the VCR MAIN MENU.

VCR MAIN MENU

I VCR Plus+

2 Timer Recordinls

|

4 Channels

5 Setup

6 Preferences
7 Audio

8 Language
0 Exit

2. Press 3 to display the TIME menu.

TIME

2 Auto Clock Set: OFF
3 get Time Zone

4 Set Daylight Savings

Spring Forward; Fall Back

In the Spring, Daylight-Savings

begins on the first Sunday in April.

Because the clock automatically
changes from 2 a.m. to 3 a.m.
(forward one hour), remember to

include the extra hour for timer
recordings falling within this time

frame.

In the Autumn, Daylight-Savings
ends on the last Sunday in

October. TheVCR clock
automatically changes from 2 a.m.

to I a.m. (back one hour).
Therefore, it can affect your

recording length.

Time Data was not found.

0 Exit

3. Press 1 to display the SET TIME AND DATE menu.

14

4.

SET TIME AND DATE

Time --:--

(hh:mm)

Date --/-_/--

Press MENU to cancel

Enter the data using the number buttons. Press 0 before

single-digit numbers and follow the on-screen directions to
exit the menus.

SET TIME AND DATE

Time 12:34 PN

Date 11/16/00 Thursday

Press CLEAR to correct
Press MENU to set

Time/Date Display

Pressing INFO displays the time

and date on the screen
temporarily.

VCR PLUS+ ® SILVER PROGRAMMING
SYSTEM

The VCR Plus+ SILVER programming system makes VCR set up

automatic by setting and updating the clock and channel list for
you. During the one-time QuickSet Guide set up, the VCR
prompts you to enter your zip code. Soon after, the VCR clock
will set itself and your VCR Plus+ programming system channel

list will be input for you.

Time, date, and VCR Plus+ system information are downloaded
from participating TV stations over your antenna or cable
system. Time and date are updated each time the VCR is turned
off (and after every power interruption). So, when your TV

stations or cable company update their lineups, your ProScan
VCR will get the most current channel list automatically, freeing
you from having to manually change the channel list yourself.

If your VCR Plus+ Silver system fails to download the proper
information for any reason, you can always manually map the
channels. You can also turn off AUTO VCR Plus+ if you keep
getting prompts about "multiple cable" services by choosing (2)

in the VCR Plus+ SETUP menu.

VCR Plus+ Download

When yourVCR Plus+ SILVER
system first downloads

information, this can take
anywhere from minutes to hours

depending on when local
broadcasters send the data.

i

VCR Plus+ system is a registered trad**nlark of Gemstar Development Corporation.
The VCR Plus+ system 15manufactured under the license from Gernstar Development Corporation.

15

MAPPING VCR PLUS+ SYSTEM CHANNELS

MANUALLY

Using the VCR Plus+ SILVER programming system can make

taping timer recordings for cable or off-air antenna easier. If your
VCR Plus+ SILVER system setup failed during the QuickSet, then

you will need to map the channels for your local service manually.
A worksheet and abbreviated codes for typical cable services in
the U.S. and Canada are provided.

1. Press MENU to display the VCR MAIN MENU.

2. Press 4 to display the CHANNELS menu.

CHANNELS

1 Auto Channel Search
2 Add/Remove Channels
3 Signal Type: CABLE

5 Cable Box Setup

0 Exit

,

Press 4 to display the VCR Plus+ system SETUP screen.

VCR PLUS+ SETUP

2 Auto VER PLus+: ON

VCR Plus+ data was found
on channel 05.

0 Exit

4. Press 1 to display the Set Channel Lists screen

.

VCR+ Channel My Channel

5 --
A --

3 -> -> -> --
2 --
I --

Use OH+/- to select
Press 0-9 to change

Press MENU to save

Enter the data following the on-screen directions using your

worksheet.

VCR+ Channel My Channel

5 46

A -+

3 -> -> -> 23

2 --

1 --

Use CH+I- to select
Press 0-9 to change

Press MENU to save

.Screen us(_ is lot an example only

TWOmDigitVCR Plus+ System

Channel Numbers for

Cable TV (U.S. List)

35 American Movie Classics
39 Arts &-Entertainment
57 Black Entertainment

54 Bravo
42 Cable News Network

45 Cinemax
98 Cinemax 2

37 The Discovery Channel

53 The Disney Channel

63 Entertainment Television
34 ESPN Sports Network
47 The Family Channel

33 Home Box Office

95 Home Box Office 2
96 Home Box Office 3

51 The Learning Channel
46 Lifetime

58 The Movie Channel

48 Music Television
49 The Nashville Network

38 Nickelodeon
64 Nostalgia Television

99 QualityValue Cable
41 Showtime

97 Showtime 2

59 Sports Channel
52 Turner NetworkTelevision

44 USA-Network

62 Video Hits I

93 Viewer's Choice I
94 Viewer's Choice 2

55 WGN Chicago
43 WTBS Atlanta

60 WWOR-New York

See next page for Canadian List

VCR Plus+ Programming
System Channel List

Refer to your local television list
for a completeVCR Plus+ system
channel list for your viewing area
or contact your cable company.
Using the list may save you some

time.

w

16

VCR PLUS+ SYSTEM WORKSHEET

Broadcast or VCR Plus+ Channel Channel Number

Cable-TV Station Number** You Receive the

Name Station On*

HBO 33

ESPN 34

Check your local or cable listing for tl)e chaone/ number you r,'coive this station inl

*" Check your/ocel listing for broadcast or VCR Plus+ cbanne/ _tumber assigned.

Two-DigitVCR Plus+ System

Channel Numbers for

CableTV (Canadian List)

67 Allarcom Pay Television/

Superchannel

44 Arts & Entertainment

72 Cable News Network-

Headline News

61 Cable News Network
70 Canadian Home Shopping

Network

56 Canal Famille
69 Cathay International

Television Inc.

68 Chinavislon Canada Corp
60 Country Music Televislon

63 Family Channel
62 First Choice

96 First Choice Two
97 First Choice Three
99 First Choice Four
90 House of Commons
91 La Chaine Francaise

51 The Learning Channel

65 MeteoMedialThe Weather

Network

48 MuchMusic Network

55 MuslquePlus
52 Nashville Network

73 Newsworld/CBC
53 Le Reseau des Sports

43 The Sports Network
64 Super Ecran
37 Super Ecran B
98 Super Ecran C

66 Telatino Network
46 TV5 Montreal
92 Viewer's Choice I
93 Viewer's Choice 2

94 Viewer's Choice 3
95 Viewer's Choice 4

71 Vision TV: Canada's

Faith Network

38 Youth TV, Canada Inc.

17

ADDITIONAL SET UP FEATURES IN THE

PREFERENCES MENU

The features in this section are all accessed through the

PREFERENCESmenu.

1. PressMENU to display the VCR MAIN MENU.

VER MAIN MENU

I VCR Plus+
2 Timer Recordings

3 Time

4 Channels

5 Setup

...... ||

? Audio

8 Language

0 Exit

2. Press 6 to display the PREFERENCES menu.

PREFERENCES

J m _mllbl _lmd IIHIT iVBl_ml

2 Auto Play: OFF
3 Auto TV/VCR: OFF

4 EnergySaver: 2:00

5 Front Panel: BRIGHT

6 Tape Speed: SLP

7 Set Auto Repeat

8 Commercial Advance
O Exit

Now you are ready to select an item

from tile menu to set up.

REMOTE VCR 1/VCR2 OPTION

The VCR's remote control unit can operate up to two
compatible ProScan, RCA, or GE VCRs. Most compatible VCRs

automatically respond to the VCR1 button without being
programmed. If you own two compatible VCRs, test them to see

if the VCRI button turns on both VCRs. If it does, then you may

want to program this VCR to respond to the VCR2 button on the
remote.

Inthe preferences menu, press 1 to select the Remote Control
feature. Then press the VCR2 button to change.

PREFERENCES

2 Auto Play: OFF
3 Auto TV/VER: OFF

4 EnergySaver: 2:00
5 Front Panel: BRIGHT

6 Tape Speed: SLP

7 Set Auto Repeat

8 Commercial Advance
0 Exit

PREFERENCES

ii _ [t_mEimr_lm

2 Auto Play: OFF
3 Auto TVIVCR: OFF

4 EnergySaver: 2:00
5 Front Panel: BRIGHT

6 Tape Speed: SLP
7 Set Auto Repeat

8 Commercial Advance
0 Exit

Remote Control Option

Remember you must press VCR I

orVCR2 on the remote--
whichever you selected in the

menu--before the remote will

operate the VC R.

18

The VCR will only respond to the VCR2 button. To change the

remote setting back to VCR1, display the PREFERENCES menu,
press 1, and then press the VCR1 button on the remote.

AUTO PLAY

This feature allows the VCR to automatically start playing when
you insert a tape with the safety tab removed. Press 2 to switch

between ON or OFF.

• Select ON if you want a tape with its safety tab removed to
start playing automatically when the tape is inserted.

• Select OFF if you do not want a tape with its safety tab

removed to start playing automatically.

AUTO TVNCR

This feature controls whether the TV/VCR switch changes

automatically to the VCR mode, when the VCR is turned on.
Press 3 to switch between ON and OFF.

• Select ON if you want the VCR to switch to the VCR mode
when the VCR is turned on or a cassette is inserted. This

only applies if you connect the IN FROM ANT. and OUT

TO TV jacks of your VCR and TV and watch your VCR on
channel 3 or 4 of your TV.

• Select OFF if you want the VCR to remain in the TV mode.
This is useful if you watch your VCR on the TV's video

input and you don't want your antenna/cable signal
interrupted by the VCR.

ENERGYSAVER

By default, this VCR automatically turns off after two hours of
inactivity. Press 4 to change the time delay or to disable the

feature.

• OFF: The VCR will remain turned on until you shut it off.

• 1:00, 2:00, or 3:00: The VCR turns off after one, two, or
three hours of inactivity.

Thirty seconds before shutting off, the VCR will warn you with
a screen reading, "The VCR will turn off in 30 seconds. Press
any key to cancel."

If you use the VCR's tuner instead of your TV to tune channels,

you may want to turn this feature off.

Auto TV/VCR

PressingTVoVCR on theVCR
(ANTENNA on remote) will still

switch between the VCR and TV
modes.

VCR mode: VCR indicator in the
display panel lights.

TV mode: VCR indicator turns off.

19

FRONT PANEL BRIGHTNESS
(VCR DISPLAY)

You can change the brightness level of the fluorescent display
panel on the front of the VCR. Press 5 to switch between the
options.

• AUTO brightens the display when the VCR is on and dims
the display when the VCR is off.

• BRIGHT keeps the display bright.

• DIM keeps the display at a low brightness level.

TAPE SPEED

You can select a preferred tape speed for recording. The speed
you select appears in the display panel and in the timer and VCR

Plus+ recording menus. Press 6 to switch between SPand SLIR
You can override the preferred tape speed:

• Press the SPEED button on the remote.

• Set the tape speed in the timer or VCR Plus+ recording
menu.

When you turn off the VCR, the tape speed reverts to the one
you have selected.

SET AUTO REPEAT

A tape can be set to play the same segment over and over in a
repeating loop with the SetAuto Repeat feature. SetAuto Repeat uses

the VCR's memory counter to determine the duration of the loop.
The Set Auto Repeat dialog box will ask for a loop end time to be

specified:

AUTO REPEAT

Set the Length of time
you want the tape to
pLay in a repeating Loop

Loop from O:OO to -:--

(h:mm)

Press ELEAR to turn off
Press MENU to exit

• The CLEAR key will erase all three numbers entered and

move the cursor back to the first position (hours).

Tape Speeds

SP (Standard Play)
Gives the best quality recording,

but fewer programs can be
recorded on the tape. Special

effects such as pause, slow motion,
picture search, and frame advance

work well when you play back
tapes recorded in this speed.

SLP (Super Long Play)
Gives three times the recording

time of tapes recorded in SR
Special effects such as pause, slow

motion, picture search, and frame
advance work when you play back
tapes recorded in this speed.

Recording Times

Cassette SP SLP

T-120 2 Hr 6 Hr
T-160 2 Hr/40 Min 8 Hr

20

• The "Press CLEAR to turn off" message will appear only after
the first number has been entered into the end time.

• Auto Repeat is set back to -:-- by resetting the dialog box, by
cassette ejecting or insertion, by powering off the VCR, by

power interruption, or by recording start.

When a duration time has been set:

• The VCR will automatically switch to rewind if the counter

meets or goes past the Auto Repeat set duration.

• The VCR will automatically switch to playback during

rewind if the counter equals or is less than 0:00.

• The Auto Repeat may be adjusted by setting the counter to

00:00. This can be done by pressing the CLEAR button while
the tape counter is on screen or on the front panel display.

• The counter will not reset while rewinding in an Auto
Repeat loop.

21

22

LEARN THE BASICS TO GET

YOU STARTED

TheseVCR basicsshould be enough for you to begin

enjoying yourVCR. Learning the remote control functions,
playing a recorded tape, and recording a program should
do just that.

However, there are other features that enhance the
enjoyment of yourVCR, but they aren't necessary to get

you started. If you want to learn more about yourVCR,

just keep reading.

V

V

3 VCR BASICS

V

V

V

V

V

VCR Basics tells you what you need to |

know in order to watch a movie or

J

tape your favorite show.

23

REMOTE BUTTONS

Your backlit remote has a light button (0) that glows in the
dark. Press this button to light the buttons on the remote. The

remote buttons remain lit when they are pressed within a few
seconds of each other. If a button is not pressed within

approximately seven seconds, the light turns off to conserve

battery power.
The remote control is capable of controlling more than just your

VCR. If you have compatible ProScan, RCA, or GE components,
you may be able to control them without having to program the

remote•

COMPONENT BUTTONS

AUX Turns on a compatible RCA or ProScan amplifier/receiver
or audio/video receiver. Can be programmed to control a

ProScan or RCA auxiliary component.
DVD Controls a compatible ProScan, RCA, or GE DVD player•

Use arrow and OK buttons to move around and select items in
DVD's menu system.

ON.OFF Turns VCR on or off when remote is set to control
the VCR. Also turns other compatible components on or off.

SAT.CABLE Turns on a compatible ProScan, RCA, or GE

satellite receiver and sets the remote to control the receiver. Can
be programmed to control different brands of receivers. Used

with the ON-OFF button to turn on a compatible cable box (if

programmed) and sets the remote to control the cable box.
TV Turns on a compatible ProScan, RCA, or GE TV and sets

the remote to control the TV. Also used with the ON.OFF
button to turn on a different brand of TV (if programmed) and

sets the remote to control the TV.
VCR1 Turns on a compatible ProScan, RCA, or GE VCR and

sets the remote to control the VCR.
VCR2 Turns on a compatible ProScan, RCA, or GE VCR and

sets remote to control VCR when it has been set up. Used with
ON.OFF button to turn on a compatible ProScan, RCA, or GE

LaserDisc player and sets remote to control the player,

VCR1 ON- OFF TV

MUTE SEARCH

SPEED _ GO BACK

GUIDE _ tNF O

CLEA_

'Q °0 0Q

{NPUT ANTENN A

II°O II

RECORD STO P PAUS E

• TRACKIN G * EDI T FR.Ab_

OOOO

24

VCR FUNCTION BUTTONS

ANTENNA Switches the picture signal so that it either comes
from the VCR or cable/antenna system. Turns VCR indicator in

VCR display panel on or off.
Arrow Buttons (,;>) Allow you to move through the menus,

enter data, and change settings of selected features.
CH + and- Selects next higher or lower channel in the VCR's

channel memory.
CLEAR Resets time counter to 0:00:00. Allows you to change

entries when setting the clock or a timer recording.

EDIT Simultaneously pauses and unpauses two VCRs when

dubbing.

FORWARD Fast forwards the tape when the VCR is stopped.
Searches forward through a tape during playback. Starts slow

motion during play-pause and increases slow-motion speed.
FR. ADV (Frame Advance) Advances the tape one frame at a

time during play-pause.
GO BACK Switches between two channels. Select one

channel and then select another using the number buttons. Press
GO BACK to switch between the two channels.

INFO Shows the status displays on the TV screen.
INPUT Selects between the line inputs and the VCR's tuner.

Line input refers to the signal coming from the component
connected to the audio/video input jacks on the back or front of

the VCR.

MENU Displays and accesses menu system.
Numbers (0 through 9) Select a channel up to 99 by pressing

two numbers. Select a cable channel over 99 by pressing and
holding I until I -- appears on the screen. Then press the other

two numbers.
ON-OFF Turns the VCR off or on.

PAUSE Pauses playback or recording. Press PAUSE again to
return to playback or recording.

PLAY Plays a tape.
RECORD Starts VCR recording. Also used for Express Recording.

REVERSE Rewinds the tape when the VCR is stopped. Searches
backward through a tape during playback. Starts slow motion
during play-pause and decreases slow-motion speed.

25

SEARCH Displays MOVIE ADVANCE screen for prerecorded
movies or displays index and Zero search menus on TV screen.

Starts COMMERCIAL ADVANCE skipping during playback

SPEED Selects a recording speed (SP or SLP).
STOP Stops the current VCR function such as record,

playback, rewind, or fast forward. If held for three seconds, this
button will also eject a stopped cassette tape.

TRACKING- and + Lets you manually reduce the streaks that
may appear on the picture during play or slow motion. Reduces
picture "jitter" during stop-action (paused) playback.

TV FUNCTION BUTTONS

ANTENNA Switches between antenna system on some TVs.
CH + and- Selects next higher or lower channel in the TV's

channel memory.

CLEAR Removes menus or status displays from the screen.
GO BACK Switches between two channels. Select one

channel and then select another using the number buttons. Press
GO BACK to switch between the two channels.

GUIDE Displays channel guide on some TV's.
INFO Shows the TV's status displays on the TV screen.

MUTE Reduces volume to minimum level.
Numbers (0 through 9) Select a channel up to 99 by pressing

two numbers. Select a cable channel over 99 by pressing and

holding t until 1 -- appears on the screen. Then press the other

two numbers.

ON-OFF Turns the TV on and off.
VOL < and > Raises and lowers sound of TV.

VCR1 ON • OFF TV

CVD VCFI2 AUX SAT'CABLE

MUTE SEARCH

0

GO BACK

GUIDff PNFO

CLEAR

,@ Q

,@,@0@

70 90

INPUT

ANTENNA

O°OO

REVERSE PLAy FORWA R

RECORD STOp PAUSE

- TRACKING + EDI T FRAO V

TV Buttons
TheTV buttons may not control

all features of all models of

ProScan, RCA, and GE TVs.

26

PLAYING A TAPE

1. Tune the TV to your VCR viewing channel
(3, 4, or TV's video input).

2. Insert a tape in the VCR.

If the Auto Play feature is set to ON, the tape automatically
begins playback (if the safety tab on the cassette is removed).

• Press FWD or REV (FORWARD or REVERSE on the remote)
to position the tape.

• Press PLAY (if necessary) to begin tape play.

• Press PAUSE for stop action.

• Press TRACKING up or down (TRACKING + or - on the
remote)

to remove any streaks from the picture, if necessary.

• Press STOP to stop playback.

AUTOMATIC REWIND

The VCR automatically rewinds the tape if it reaches the end of
the tape during playback. While rewinding, you can press

ON.OFF and the VCR will turn off after rewinding.

TAPE EJECT

Press and hold the STOP button on the VCR front panel or
remote control for a few seconds and the VCR will eject a

stopped tape.

Pause 1

If you pause, the VCR
automatically switches from pause
to stop after a few minutes to

reduce tape wear.

k

Automatic Tracking

The VCR has automatic tracking

which adjusts the picture when

playing back a tape recorded on

anotherVCR. Automatic tracking

is turned on whenever a tape is
inserted or theVCR's power is

turned on.

27

RECORDING

If you want to record something that you're watching, you can
use basic recording.

1. Set the tape speed by pressing the SPEED button on the
remote. (See "Tape Speed" in Setting Up the VCR section for
information about tape speeds.)

2. Press the RECORD button to begin recording.

3. Press STOPto stop recording.
If you just want to pause the recording for a short time (like

during a commercial), press PAUSE instead of STOP.

CHECK THE SAFETY TAB
No matter which recording option you use, make sure there is a

tape in the VCR, and that the tape's safety tab is in place. You
cannot record on a tape with the safety tab removed.

Stalely Tab

If the safety tab is removed and you want to record over it,
simply cover the hole with vinyl tape.

28

SEVERAL RECORDING

OPTIONS

Now that the necessary steps to operate the VCR

have been examined, it's time to look at the different
recording features available to suit various recording

needs.

Recording Features:

Recording (explained in VCR Basicssection)

Express Recording

Program Express Recording

Timer Recording

Timer Recording with theVCR Plus+ System

Broadcast Stereo or Second Audio Program (SAP)

Audio Only Recording

Copying and Editing Tapes

V

¥

¥

4 RECORDING

V

¥

V

V

29

RECORDING FEATURES

There are five ways to record programs:

• Recording lets you press one button to start recording a
program (See VCR Basics section).

• Express Recording (XPR) allows recording to start while a
program is being watched, and automatically stops

recording after a designated period of time.

Program Express lets you program a timer recording using

the VCR's front panel controls.
Timer Recording allows the VCR to be programmed for

automatic recording, starting and stopping at a
predetermined time.

Timer Recording with VCR Plus+ allows the VCR to be
programmed to record just by entering a PlusCode

programming system number found in some TV program
guides.

EXPRESS RECORDING (XPR)

Use express recording when you want to quickly record the
remaining portion of the program you are watching.

1. Press the SPEED button on the remote if you want to
override the preferred Tape Speed setting.

2. Press the RECORD button to begin recording.

3. Repeatedly press the RECORD button to set up the recording
duration.

Rec Ch 36
Record Length 0:00

Press REC to set tength

Rec Ch 36
Record Length 1:30

Press REC to set length

Each time you press the RECORD button, you add 30 minutes to
the recording time (up to 4 hours).

The VCR continues to record for the amount of time you

indicate, and then automatically turns off.

To stop an express recording, press and hold STOP for several
seconds until STOP appears.

Express Recording (XPR)

Express recording is a great way to

tape the last quarter of the game,
or the last part of a movie when
you have to leave.

3O

PROGRAM EXPRESS

Program Express allows you to quickly program the VCR for a
complete one-time recording using the VCR's control panel

instead of the on-screen menus. The VCR automatically turns off

at the end of the recording. You can use the arrow keys on the

remote control or the VCR's front pane[ to move through these
menus.

.

2.

3.

4.

5.

6.

Insert a tape with the safety tab in place. Make sure the
clock is set correctly.

Open the control door in the lower left corner of the VCR's
front panel.

Press PROG. EXP.to activate the display. The channel
number flashes in the display panel.

Use the up • and down • arrow buttons to choose a

channel, then press PROG. EXR to select it.

Repeat step 4 to enter START time, END time, DATE of
recording, and tape SPEED information.

Press PROG. EXP.when SAVE flashes in the display. SAVED
appears to let you know the program is set.

Use the up • and down • arrow buttons to review or
cancel your entries.

7. Turn off the VCR.

TIMER RECORDING

You can set up as many as eight timer recording programs.

1. Press MENU to display the VCR MAIN MENU.

VCR MAIN MENU

1 VCR Ptus+

| "--- l!

3 Time

4 Channets
5 Setup

6 Preferences

7 Audio
8 Language

0 Exit

2. Press 2 to display the TIMER RECORDINGS menu.

31

TIMER RECORDINGS

b_l_mm_n _ _lox_n _nnJ_

2 Review Existing Progs.

3 Use VCR Plus÷ Code

0 Exit

3. Select 1 to create a New Program.

HOW often should this

program record?

2 Daily (every day)
3 Weekdays (M-F)
4 Weekly (once per week)

0 Cancel

4. Select how often you want the program to record.

,

.

Program 1 (One time)

Channel --
Start Time --:--
End Time --:--

Start Date --/--/--
Tape Speed SLP

Press MENU to cancel

Enter the data for the program with the number buttons.

The data includes the channel number (press INPUT to
select the line input), start time including AM or PM, and
end time. The start date is automatically entered based on
the VCR clock. Both the date and speed can be changed.

Review the information to make sure it is correct, and then
press MENU to save.

Program 1 (One Time)

Channel 03 Cable
Start Time 08:00 PM
End Time 09:30 PM
Start Date 11/16/00 Thu

Tape Speed SLP

I=SP 2=SLP

Press CLEAR to correct

Press MENU to save

Program I has been saved

Remember to insert a
recordable tape and

turn the VCR off before
the program start time.

Remember to leave your

cable box on and tuned

to the desired channel.

Timer Recording Information

Clock must be set correctly.
Insert a tape with the safety tab in

place and enough tape to record
the program.

The output of your cable box
appears in the Channel item of the
timer recording menu if you've set

up theVCR for a cable box for all
channels.

PROGRAMS OVERLAP appears if

you have entered two programs
where the times overlap.

TIMER appears in the display when
you turn off theVCR and a timer
recording has been set. TAPE

flashes if there is no tape in the
VCR.

For cable box or satellite receiver,

turn it on and tune it to the
channel you want to record before

the recording is to begin.

32

TIMER RECORDING WITH THE VCR PLUS+

PROGRAMMING SYSTEM

You can use VCR Plus+ to simplify timer programming by using
the PlusCode" programming number shown in your local
television programming guide.

SETTING UP THE CHANNEL LIST

If you did not set up the VCR Plus+ channel list, you can do
it now.

1. Display the CHANNELS menu from the VCR MAIN MENU.

2. Display the VCR Plus+ Channel List menu.

3. Go to Setting Up Your VCR if you need more information on
setting up your VCR Plus+ channel list.

USING THE VCR PLUS+ PROGRAMMING SYSTEM

1. Press MENU to bring up the VCR MAIN MENU.

VCR MAIN MENU I

1 VCR Plus+

/

2 Timer Recordings
3 Time

CHANNELS

1 Auto Channel Search

2 Add/Remove Channels

3 Signal Type: CABLE

VCR+ Channel My Channel

5 46

4 --

3 -> -> -> 23

2 --

1 --

Use CH+/- to select
Press 0-9 to change

Press MENU to save

VCR MAIN MENU

2 Timer Recordings
3 Time

4 Channels
5 Setup
6 Preferences
7 Audio

8 Language

0 Exit

2. Press 1 to display theVCR PLUS+ system menu.

VCR PLUS+

Enter PlusCode Number

(from TV listing)

Press MENU to cancel

3. Enter the VCR PlusCode system shown in your local
television programming guide (Screen shown is just an

example).

K]ontinu{'s on t]{,Jct pa,_e)

PlusCode is a registered trademark of the Gemstar Development Corporation
The VCR Plus+ system is manufactured under the license from Gemstar Deve/olJment Coq)oration.

33

IE])nfinu_d triJill prevlllu_ paA,eJ

VCR PLUS+

Enter PlusCode Number

(from TV listing)

412876

Press CLEAR to correct
Press MENU when done

4. Press MENU to enter the VCR PlusCode system number.

How often should this
program record?

Iiimmr --

2 Daily (every day)
3 Weekdays (M-F)

4 Weekly (once per week)

0 Cancel

5. Indicate how often you want the program to be recorded.

.

Program I (One time)

Channel 03 Cable
Start Time 08:00 PM
End Time 09:30 PM

Start Date 11/16/00 Thu

Tape Speed SLP

Press CLEAR to adjust
Press MENU to save

Change the speed with the SPEED button on the remote or
the program end time with the CLEAR button on the remote
(if necessary).

Changing the end time comes in handy when you are
recording a program, such as a sporting event, that may

exceed the scheduled broadcast time.

7. Press MENU to save the program.

Program I has been saved

Remember to insert a

recordable tape and
turn the VCR off before

the program start time.

Remember to leave your

cable box on and tuned
to the desired channet,

VCR Plus+ Recording
Clock must be set correctly.

Insert a tape with the safety tab in
place and enough tape to record

the program.

UNRECOGNIZED NUMBER...
PLEASE RE-ENTER appears when

theVCR does not recognize the

PlusCode number.

PROGRAMS OVERLAP appears if
you have entered two programs
where the times overlap.

TIMER appears in the display when
you turn off theVCR and a timer

recording has been set. TAPE
flashes if there is no tape in the

VCR.

For a cable box, turn it on and tune
it to the channel you want to
record before the recording is
to begin.

34

STOPPING A TIMER RECORDING
To stop or cancel a timer recording in progress (even an Express

Recording):
" Press and hold the STOP button for several seconds until

STOP appears.

REVIEWING AND CLEARING PROGRAMS

To review programs that you have already set up:

1. Press 2 when the VCR MAIN MENU is displayed to display
the TIMER RECORDINGS menu.

TIMER RECORDINGS

I Create a New Program

3 Use VCR Plus+ Code

0 Exit

2. Press 2 to display the Review Existing Progs. screen.

Program 1 (One time)

Channel 104 Cable
Start Time 12:00 AM
End Time 01:30 AM
St'art Date 11/16/00 Thu

Tape Speed SLP
Press INFO to edit

Press CLEAR to erase
Press MENU for next prog

3. Press INFO to edit, CLEAR to erase, or MENU to see the next
program if there is one.

EDITING A TIMER PROGRAM

Instead of having to delete and re-enter a timer program, you

can edit incorrect entries of the program.

1. Display the program you want to edit, and press INFO.

2. Indicate how often you want the program to be recorded.

3. Use the CLEAR or left • and right • buttons to move the
cursor to the item you want to change.

4. Use the number or up A and down • buttons to enter the
correct information in the program.

5. When you have made your correction(s), press MENU to
save the timer program.

Remote Control Buttons

GUIDE INFO

MENU CLEAR

Front Panel Buttons

pROG EXp @

CLEAR INF0

(_ _ANNEL

]_CVJNG

35

RECORDING BROADCAST STEREO TV OR

SAP (SECOND AUDIO PROGRAM)

Some TV programs are broadcast with stereo audio or SAP
(Second Audio Program/.

1. Turn on the TV and tune it to the VCR viewing channel
(either 3, 4, or TV's video input).

2. Insert a tape with safety tab in place.

3. ff your VCR viewh_g channel is 3 or 4, make sure the VCR
indicator appears in the VCR's display panel. If not, press

TV,VCR on the VCR or ANTENNA on the remote to turn it on.

4, Press the SPEED button on the remote if you want to

override the preferred Tape Speed setting. The tape speed

indicator appears on the TV screen.

5. Select the channel or line input to be recorded.

6. Set the Reception: STEREO/MONO/SAP feature for the type
of audio you want to record, See Other Features section.

0 Exit

7. Press RECORD to start recording.

8. Press STOP when you are finished.

RECORDING AUDIO ONLY
You can record audio only from another audio source

connected to either the AUDIO IN 1 (R and L) jacks on the back
of the VCR or the jacks on the front of the VCR.

1. Press the INPUT button once to record from the back
AUDIO IN jacks. L1 will appear in the VCR's display panel.

Press the INPUT button twice to record from the front

AUDIO IN jacks. L2 will appear in the VCR's display panel.

2. Press the SPEED button on the remote if you want to
override the preferred Tape Speed setting.

3. Start audio source playing and press RECORD to begin
recording.

4. Press STOP when you are finished.

Recording only audio will erase

anything previously recorded on
the tape.

Audio Connection

VCR

AMPLIEtEW
RECEIVER

36

PLAYING BACK AUDIO ONLY

To get stereo sound, connect the AUDIO OUT jacks of the VCR
to the appropriate input on your amplifier or receiver. Do not use

the phono input. Refer to your amplifier or receiver user's guide.

USING TWO VCRS FOR COPYING AND
EDITING TAPES

Use one VCR as the playback VCRand the other as the

recording VCR.

1. Turn on the TV and VCRs.

,

3.

,

Tune the TV to the VCR viewing channel (either 3, 4, or TV's
video input).

If you connected your VCR using the IN FROM ANT. and
OUT TO TV jacks, tune recording VCR to channel 3 or 4--
the one selected on the back of the playback VCR.

If you have connected your VCR using the audio/video
jacks, press INPUT on the recording VCR's remote to select

the line input. Select L1 for the jacks on the back of the VCR
or L2 for the jacks on the front.

Insert the tape you want to copy into the playback VCR.
Insert a blank tape with safety tab in place into the

recording VCR.

.

Press PLAY on the playback VCR to begin playback. When
you reach the point on the tape or program where you want
to begin copying, press PAUSE. You may need to adjust the

tracking.

6. Press the RECORD button, then press PAUSE, on the

recording VCR.

7. Press the PAUSE buttons on both VCRs at the same time to
begin copying the tape.

8. To edit segments that you do not want to copy:

• Press PAUSE on recording VCR to pause copying.

• Locate the next segment you want to copy on playback VCR
by using FWD, REV, and PLAY, and then press PAUSE.

• Press PAUSE on both VCRs at the same time to resume
copying.

9. Press STOP on both VCRs when you are finished.

Caution:

The unauthorized recording of
satellite broadcasts, television

programs, or other copyrighted
materials may infringe the rights

of others.

Two VCR Connection

GABLE BOX

OR ANTENNA'_

PLAYBAGKVCB

RECORDING VCR

TO TV TO TV

Nr)te that the twr_ V( R, used in the, diagran) may not
k)_k ex,_ tly like' Ih_' VCRs you are __Jnnecting The

iil_portailt thin)4 i_ t_J nlatl h the pr_Jpl,r l_l!_/_'

I _uln_f tiiJiis L/_c, the, ()U'/hi( ks _lt the' iflayl)acl_ VCR. R)
i cJnnl,i t tr_ IN I,tl ks r;t thl, _c i_rding V( R R I_u_ut

i,l¢ l_s cr_nne_ t tll R. /NPUT jal ks, L {)utput t_l L input,
and VIDEO out r rmnc,cts _ VIDEO in

37

USING DUAL REMOTE WITH AUTOEDIT

Use this VCR as the playback VCR and set it to respond to VCR2
on the remote as described in Setting Up the VCR section. Use
your other compatible VCR as the recording VCR, which should

respond to VCR1.

1. Follow step 1 4 in the "Using Two VCRs for Copying and
Editing Tapes."

2. Press VCR1 on remote to control recording VCR. Press
RECORD (REC), then PAUSE, to put recording VCR in

pause mode.

3. Press VCR2 on remote to control playback VCR.

4. Use FORWARD, REVERSE, and PLAY to locate the point

where you want to begin copying. Press PAUSE while VCR

is playing to put playback VCR in pause mode.

5. Press EDIT on remote to start the VCRs copying.

6. Press EDIT again when you want to pause copying.

7. Repeat step 4-6 as needed.

8. Press VCR1, STOP, then VCR2, STOP, when you are

finished.

38

CONTROLLING YOUR

OTHER COMPONENTS...

The remote'sTV and SAT, CABLE buttons can be

programmed to control other brands of remote
controllableTVs, digital satellite receivers, and cable boxes.

The remote is already programmed to operate most

ProScan, RCA, and GE televisions and satellite receivers.

TheAUX button can be programmed to control a ProScan
or RCA auxiliary component.

V

V

V

V

PROGRAM THE REMOTE

Y

Y

[ • •

Y

39

ABOUT PROGRAMMING THE

REMOTE

The universal remote's TV and SAT.CABLE buttons can be
programmed to control other brands of remote controlled TVs,

digital satellite receivers, and cable boxes. Your remote is
already programmed to operate most ProScan, RCA, and GE

televisions as well as digital satellite receivers.
The AUX button can be programmed to control a ProScan or

RCA auxiliary component.

TESTING THE REMOTE

To determine whether the universal remote needs to be
programmed, turn the component on (such as a TV), point the

remote at the TV and press the TV button. Then press ON.OFF,
CH +, or CH - to see if the TV responds to the remote

commands. If the TV does not respond, then the remote control
needs to be programmed.

PROGRAMMING THE REMOTE TO

CONTROL A TV, SATELLITE RECEIVER,

OR CABLE" BOX

The remote features Code Search, a technology that largely

automates the programming process. Fol[ow these steps to
program the remote to control a TV, digital satellite receiver, or

cable box.

,

2.

Turn on the component you want to control (TV, digital

satellite receiver, or cable box).
Press and hold the button you want to program (TV or

SAT.CABLE). While holding the component button, press

and hold ON-OFF until the LED on the remote flashes, then

release both buttons.

3. Press and release PLAY, then wait five seconds.
The remote searches through a set of codes. If, after five

seconds, the component does not turn off, press PLAY again
to tell the remote to search the next set of codes.

4.

You can press FORWARD to individually search through the

last ten codes that were transmitted when you pressed PLAY.
Repeat step 3 until the component turns off, or you have

searched through all of the codes.

ON.OFF TV

You'll use these buttons when you
program the remote to control a

TV, digital satellite receiver, or

cable box.

4O

To cancel Code Search, press and hold CLEAR until the
LED turns off.

There are 20 total sets of codes. If the device does not turn
off after pressing PLAY 20 times, the remote cannot control

that particular component.

If the component you want to control does turn off:

1. Press and release REVERSE, then wait two seconds. Repeat
this step until the component turns back on. This means

the remote has identified the correct code.

2. To finish, press and hold STOP until the LED turns off.

USING DIRECT ENTRY

Direct Entry is another way to program your remote if the

Automatic Code Search is unsuccessful.

1. Turn on the component to be programmed.

2. Look up the brand and code number(s) for the component
in the code list on page 41.

3. Press and hold the button on the remote you want to
program.

4. Enter the code from the list on page 41.

5. Release the button, and then press ON.OFF to see if the
component responds to the remote commands. If it
doesn't, try pressing the component button and then
ON.OFF again.

6. Repeat these steps using the next code listed for your
brand if you get no response.

OPERATING COMPONENTS

After programming the remote, see which buttons operate your
component.

1. Point the remote at the component, and press its
corresponding button on the remote.

2. Experiment to see which buttons operate your component.
Try pressing buttons that relate directly to the component.

This remote may not operate all
models andfor brands of

components.

Note the difference between the

VCR and other component's on-

screen displays to determine

which one the remote is

operating.

41

PROGRAMMING THE REMOTE
TO CONTROL AN AUXILIARY
COMPONENT

Your remote can also control the brands of the equipment listed,
such as a radio, CD player, tape player, or phonograph. It is

already programmed to control some ProScan and RCA
amplifiers and audio/video receivers.

1. Turn on the component to be programmed.

2. Look up your component's code number on the code list.

3. Press and hold the AUX button.

4,

5.

Enter the 4-digit code from the code list on the next page.
Release the AUX button and press ON.OFF or CHAN up or

down to see if the auxiliary component responds to the

remote commands.

OPERATING THE AUXILIARY COMPONENT
After you have programmed your remote, see which buttons will

operate your component.

1. Point the remote at the component and press AUX. If it does

not turn on, press AUX and then ON.OFE

2. You may want to experiment to see which buttons will
operate your component. Try pressing buttons, such as play,

REVERSE, and FORWARD.

0N'0FF

AUX

You'll use these buttons when you
program the remote to control an

auxiliary component.

Auxiliary Component Codes

ProScan/RCA/Dimensia (only)
AM/FM 0003
Auxiliary Component 0004

Phono 0005
Tape I 0006

CD 0007

This remote may not operate all

models of the brands that are
shown.

42

k

ABEX ......................................................................................II 72

Admiral .........................................................................1001. 1173

ASventura...............................................................................1174

Aiko .....................................................................................1016

Aileron ......................................................................................1046

Amtron .....................................................................................1038

Akai.........................................................................................1002

Anam Nauonal .............................................................1003, 1038

AOC ............_..................... 1004,1005, 1006, 1007, _ 175, 1176

Audiovox ..................................................................................1038

Belcor .......................................................................................1004

Bell & Howell .....................................................100L 1083, 1162

Bradford ..................................................................................1038

Brokwood ............................................................................1004

Candle ....................................................1004, 1006, 1000, 1174

Capehar¢ .................................................................................1175

Celebrity ................................................................................1002

Centurio.............................................................................f009

Citizen ............................................... 1004, 1006, _008, 1016,

.......................................................1038, 1105, 1171. 1174, 1177

Clairton ........................................................................... 1176

Colortyme .................................................................1004, 1006

Concerto ......................................................................1004.1006

Contec/Cony ..............................1012, 1013, 1014, 1038, 1176

Craig ..........................................................................................1038

Crown ............................................................................1038, 1171

Curds-Mathes ..................................................1000, 1004, 1006,

...................................................................1015,110S, 1162,1171

CXC .........................................................................................1038

Daewoo .............................................................1004, t005, 1006.

........................................................10t6, 1017. 1018,1127, 1171

Daytron ...............................................................1004, 1006, 1171

Dimensia ...................................................................................1(300

Dumont ........................................................................1004, IISI

Dynatech ..................................................................................I J78

Electronband.................................................................1002, 1176

glectrohome ................................1003, 1004. 1006, 1019, 1022

Emerson ...........................1004, 1006, 1012, 1014, 1023, 1024,

.................................1025, 1026, 1027, 1028, 1029,1030, 1031,

................................1032, 1033,1034, _035, 1036, 1037, 1038,

................................1039. 1041,1042, 1043, 1044, 1046, 1047,

...................... H23, 1124, 1162, 1171, 1176, 1177, 1179, H91

Envision..........................................................................1004, 1006

Fisher..................................1048, 1049, 1050. t0SI. 1162, 1180

Fuiitso......................................................................................_046

Funai...............................................................................1038, 1046

Fu_retec ..................................................................................1038

GE ..........................1000, 1003, 1004, 1006, 1022, 1052, 1054,

.......................105S, 1087, 1164, 1165, 1166, 1167, 1168. 1181

Gibralter .......................................................................1004, 115_

Golgstar ...................................................1004, 100S, 1006, 1012

.......................1019, 1056, 1057, 1058, 1155, 1156, 1171, 1172

Grundy ................................................................1038, 1046, 1171

Hallmark ........................................................................1004, 1006

Harvard .....................................................................................1038

Hitachi ................................1004, 1006, 1012, 1013,1059, 1060.

.......................1061,1135, 1136, 1137,1138,11391140, 1141,

.......................1142,1143,1144,1145,1146,1148,1150,1179

IMA ............................................................................................_038

Infinity .......................................................................................1062

Janeil ..........................................................................................1174

JBL ..............................................................................................1062

JCB .............................................................................................1002

JC Penney ...............................................10(30,1004, 1005, I006,

............................................1008,1022,I052,1054.1058,I063,

........................1064,1072,1007,II05,1128,1171,I172.1181

Jensen.............................................................................1004, 1006

JVC ...........................................................1012, 1013. 1054, 1060,

.......................1065, 1066. 1067, 1089,1157, 1158, 1159, 1182

Kawasho .............................................................I0_2,I004,1006

Kaypani......................................................................................1175

Kenwood ............................................................I0_4,1006,1019

K_ossNovabeam ....................................1068,1069,1174,1183

KTV ...............................................1038.1070,i171,1176,1177

Loewe ........................................................................................1062

Log k ............................................................................1083

Luxman ..........................................................................1004,1006

LXI ......................................................................1000. t006, 1049,

............................................1062.I071,1072.1073,1162,1181

Negatron......................................................................1006,1059

Magnavox ................................................1004, 1006, 1008, 1019.

......................1062,1060,1069,1074,1075,1076,1077,I088,

.......................I089.1130,1131,1132,1133,1134,1183,1184

Majestic .....................................................................................t083

Maran_s .....................................................................................1062

Marantz ....................................................1004. 1006, 1062, 1078

MEI .............................................................................................1176

Mernorex ......................................I001, 1006. 1082, 1083, 1162

NGA .......................................................1004, 1(305,1006, 1019,

........................................................1022. 1051. 1079, 1080. 1082

Midland .........................................1054, 1151.I171,1172.1181

Minutz ......................................................................................1052

Mitsubishi ...............................................1004, 1005. 1006, 1019,

..................................1022. 1051, 1079, 1080, 1081. 1082, 1125

Montgomery Ward .......................................................... 1003

Mo(orota ....................................................................1003, _173

MTC ................................ 1004, 100S. 1006, I lOS, 1176,1178

Multi(ech ............................................................... 1038,1178

Multlvls_on ............................................................................1084

NAD ........................................................1006. 107L 1072,1185

NEC ............................................ 1003, 1004, 1005, 1006,1089

NIKKO ..........................................................................1006,1016

NTC ................................................................................ 1016

Onwa ......................................................................................1038

Optimus ................................................................................1185

Optomca ................................................................... !095. 1173

Orion .........................................................................1035.1t91

Panasonic .............................................. 1003.1054. 1062,1170

Philco ......................1003, 1004. 1005. 1006, 1008, 1012. 1019.

........................1062. 1068. 1069,1074, 1075. 1077. 1183,I L84

Philips......................1003.1004. 1008, 10_2, 1019, 1062, t068,

........................ 1069. 1074, 1075. 1076. 1086. 1087, 1088, 089

Pilot ................................................................................1004, I I 7I

Pioneer ................. 1004, 1006, 1090, 1091. 1092. 1179, 1185

Portland ........................................1004, 1005, t006. 1016, 1171

Price C_uh ......................................................................... 1105

Prism .........................................................................................1054

ProSean .........................................................................1000, 1181

Proton ...........................................1004, 1006, 1012, t093, t 175

Pulsar.........................................................................................1151

Pulser ........................................................................................1004

Quasar .....................................................1003, 1054, 1070, 1094

Radio 5hack/Realisuc ...........................1000, 1004, 1006, 1012,

.............................................1038, 1049, 1095, 1162, 1171, 1172

RCA .............................................1000, 1003, 1004, 1005. 1006.

.................................1007, 1019, 1096, 1098, 1099, _100, _101,

.......................1102, 1103, 1129, 1179, 1181, 1187, 1188,1190

Rhapsody ..................................................................................1176

Runco ........................................................................................I 15I

Sarnpo ...........................................1004, 1006, 1171, 1172, 1175

Samsung..................................................1004, 1005. 1006. 1012,

................................ 1015, 10t9, 1104, 1105, 1106, 1171, 1172

Samsux .................................................................................117!

Sansui .......................................................................................1191

Sanyo........................................................1004, 1048, 1049. 1050,

.............................................1080, 1107, 1108, 1162. 1169, 1180

Scotch .......................................................................................1006

Scott ........................1004, 1006. 1012, 1024, 1035, 1038, 1046

Sears ........................................................1000, 1004, 1006, 1013,

................................1019, 1046, 1048, 1049, 1050, 10SI, 1066,

.......................1071, 1072, 1109, I 110, I _62, 1180, 1181, 1189

Sharp .......................................................1004, 1006, 1012, 1029,

.................................1095, I III, 1112, 1113, 1122, 1171, 1173

Shogun ......................................................................................1004

Signature .............................................................1001, 1083, I 115

Simpson....................................................................................1008

Sonic ..........................................................................................1176

Sony ...........................................................................................1002

Soundesign ...................................1004, 1006, 1008, 1038, 1046

Squareview ...............................................................................I 189

SSS...................................................................................1004. t038

S_arlite .......................................................................................1038

Supre-macy ..............................................................................I 174

Supreme ....................................................................................1002

Sylvania...................1004, 1006, 1008, 1019, 1062, 1068, 1069.

............ 1074, 1075. 1076, 1077, 1088, I 116, t 161, 1183, 1184

Symphonic ..........................................................1033, 1038, _189

Tandy ........................................................................................It73

Tatung .............................................................................1003, 1178

Technics ...................................................................................1054

Techwood ...........................................................1004, 1006, 1054

Teknika ...................1004, 1(305,1006, 1008, 1012, 1013, 1016,

......................._038, 1046, 1076, 1082, 1083, 1105, 1170.1171

Teleeaption ...............................................................................I 117

TMK ................................................................................1004, 1006

Toshiha ...................................................1049, _071, 1072, 1089,

............................................1105, 1109, II 17,II 10, 1160,1162

Totevision .................................................................................1171

UniversaI ........................................................................1052, 1087

Victor ............................................................................1066,1182

Vidtech ................................................................1004, 1005.1006

Viking .........................................................................................1174

Wards ................................1000, 1(301,1004, 1005, 1006, 1019,

......................_024, 1033, _046, 1052, 1062, 1068, 1069, 1074,

........... 1075, 1076, 1093, 1087, 1088, 1095, I 119, _120, 1184

Yamaha.....................................................1004, 100S, 1006,1019

Zenith ............................................1004, 1151, 1152, 1153,1154

ABC .........................5002, 5003, 5004, 5005. 5006. 5007, 5053

Antronix ........................................................................S008, 5009

Archer ...................................................S008,5009, SOI0, 501 I

Cablezenna .............................................................................5008

Cab_eview ................................................................................S008

Century ..............................................................................S011

Citizen ............................................................................. S011

Colour Voice .............................................................5012, 5013

Comtronics ........................................................ 5014.5015

Con_ec ..................................................................................5016

Eastern........................................................................ 5017

Garrard ...............................................................................501 I

GC Electronics ....................................................................5009

Gemini ......................................................... 5018. 5019, 5049

General Instrumen_ ...........................................................S003

Hamfin ........................................ 5020, 502 I, 5022. 5035, 504S

Hitachi ........................................................................... S003

Hytex ................................................................................ 5002

Jasco .................................................................................. 5011

Jerrold ......... 5003, 5005, 5007.5018. 5023, 5024, 5046. S053

Magnavox ............................................................. S025

Memore× ........................................................................ 5026

Movie Time ............................................. 5002, S027, S020

NSC ................................................... 5002, 5027, 5020

Oak .................................................... S002,S016,5029

Panasonic........................................................... S048, 50S2

Paragon ............................................................................. 5026

Philips ...........501 I, $012. 5013,5010, S025. 5030, 503I, 5032

Pioneer ...........................................................................5033, 5034

Pulsar........................................................................................5026

RCA .....................................................................5047,5049. 5052

Realistic .......................................................................5009, 5049

Regal ..............................................................................5022, S035

Regency ....................................................................................5017

Rembrandt ..........................................................................5003

Runco ....................................................................................5026

Samsung........................................................................5014, S034

Scienti0cAtlanta .....................................5006, 5036, 5037. 5038

Signal...............................................................................5014, 5018

Signature ...................................................................................S003

SLMarx .....................................................................................5014

Sprucer ....................................................................................5052

Srarcom ...........................................................5007, 5018, 5053

S_ar_ate........................................................................5014, S018

S_arquest..................................................................................5018

Tandy .......................................................................................S040

Teleview ...................................................................................5014

Tocom ................................................................5004, 5023, 504!

Toshiba................................................................................L.,. 5026

Tusa............................................................................................5018

TV06 ..........................................................................................S027

Unika ..................................................................5008,5009, 501 I

United Artists ..........................................................................S002

United Cable ...........................................................................S053

Universal ..................................................5008, 5009,5010, SOI I

Videow_y ..................................................................................S044

Viewstar ...................................................5015, 5025, 5027, 5040

Zenith ..................................................................5026,5050, 5051

Chapparal ......................................................................50S6, SOS7

Drake ..........................................................................5058, $059

GE DBS..........................................................................5000, 5001

General Instruments ........................................5060, 506 I, 5062

Panasonic..................................................................................5075

Primestar ..................................................................................5076

Proscan ..........................................................................5000, 5001

RCA ..............................................................................5000, 500 I

Realistic ...................................................................................5063

Sony ..........................................................................................5072

STSI ...........................................................................................5064

STS2........................................................................................5065

STS3...........................................................................................5066

STS4.........................................................................................5067

Toshiba ......................................................................................$068

Toshiba .....................................................................................5073

Unlden .......................................................................................S069

(ForsomePRO$CAN.RCA,GEandDimensiabrandsonly)

AM/FM .....................................................................................0003

Auxil_ary Component ........................................................0004

CD ........................................................................................0007

DBS I ....................................................................................0008

DBS2 ....................................................................................001I

DVD ........................................................................................0010

Phono .......................................................................................0005

43

44

FEATURES TO ENHANCE

VCR OPERATION

Commercial Advance

Movie Advance

Picture Search Options

Pro-Tect PlusTM Locking

Tracking

Time Counter

On-Screen Displays

Audio Reception

AudioTape Playback

V

V

V

¥

16

¥

OTHER FEATURES

¥

¥

45

COMMERCIAL ADVANCE ®

The feature, Commercial Advance, is patented techno{ogy that

detects and marks most commercials on your tape for any
recording that is more than 15 minutes long. After recording, the
VCR rewinds the tape to the beginning of the recording and

determines where the commercials are located. It then marks the
beginning and end of the detected commercial segments, and

when finished, returns the tape to the end of the recording. It

does not erase commercials from the tape.

During playback, the,VCR automatically skips the detected
commercial segments, or you can chose to manually skip them.

This feature reduces three minutes of commercials to
approximately 8-12 seconds of fast forwarding in the SLP speed.

You can select a background display of blue or see the recorded
video as the commercials are skipped.

Because television signals do not indicate where the ads are
located, the Commercial Advance feature finds and marks them

through a set of formulas based on how television is broadcast.

Since television stations broadcast differently and insert their
own commercials, you may experience some variations in this
feature's effectiveness. Station promotions, identifications, and

announcements are not considered commercials, but might be

skipped by this feature. For more information, see "Questions

and Answers About Commercial Advance" in the Reference

section of this manual. ALl Commercial Advance features are

accessed through the COMMERCIAL ADVANCE menu.

I. Press MENU to display the VCR MAIN MENU.

VCR MAIN MENU

1VER Plus+
2 Timer Recordings

3 Time
4 Channels

7 Audio

8 Language
O Exit

2. Press 6 to display the PREFERENCES menu.

COMMERCIAL ADVANCE is a registered trademark of SRT, Inc.

46

PREFERENCES

1 Remote Control: VCRI
2 Auto Play: OFF
3 Auto TV/VCR: OFF
4 EnergySaver: 2:00

5 Front Panel: BRIGHT

G Tape Speed: SLP
7 Set Auto Repeat

0 Exit

3. Press 7 to display the COMMERCIAL ADVANCE menu.

COMMERCIAL ADVANCE
I Marking: ON
2 Playback: AUTO
3 Display: BLUE

0 Exit

Now you can select one of the COMMERCIALADVANCE

features.

COMMERCIAL ADVANCE MARKING

Press 1 to turn commercial Marking:ON or OFF.

• Select ON, and the VCR will mark commercials within
approximately 30 seconds for the following types of

recording:

-- Timer, Timer with VCR Plus+, or Express Recording

Sets the VCR to automatically mark commercials after
the power is tuned off.

-- Recording Allows the VCR to prompt you to mark the
commercials when you've stop the recording.

The VCB is waiting to
mark commercials in the

program you recorded.

I Mark them now
2 Mark them later
3 Don't mark commercials

The VCR will begin

marking in 30 seconds...

• Select OFF and the VCR will not mark the commercials.

Commercial Advance and

Multiple Timer Recordings

When using the timer to record
two or more back-to-back

programs on the same channel,
you might want to set each up

seperately in the timer menu.This
way, introductions and conclusions
of each show are not skipped.

47

COMMERCIAL ADVANCE PLAYBACK

Press 2 to switch between Playback: AUTO and MANUAL.

• Select AUTO to have the VCR automatically advance
through the blocks of marked commercials.

* It works with most 30, 45, and 60-second commercials.
* A commercial group starting with the first two minutes or

last two minutes of a recording will not automatically be

skipped.
Acommercial will not be skipped if a recording starts in the

middle of a commercial segment, one isolated commercial
is shown without others, or a commercial is longer than one

minute. Press FWD on the VCR (FORWARD on remote) to
scan through the commercial.

Part of a recorded program may be skipped if the program
segment is either between commercials and is less than one

minute, or there are frequent dark and quiet scenes in the
program. If this happens, automatic skipping can be

temporarily stopped by pressing PLAY (or STOP) on the

remote control while that portion of the tape is being
skipped. Then, reverse the tape back to a point just before
the segment starts and press PLAY. Automatic skipping will
be re-enabled after the VCR detects the end of the segment.

• Select MANUAL and the VCR won't advance through the
blocks of marked commercials until you press SEARCH.

If you press SEARCH during playback of material other than
commercials, the VCR advances to the end of the next "marked"

commercial block and resumes playback.

The VCR resumes playback when it reaches the end of the

marked commercials.

COMMERCIAL ADVANCE DISPLAY

Press 3 to switch between Display: BLUE or VIDEO.

• Select BLUE to display a blue background when the VCR
advances through the block of marked commercials.

• Select VIDEO to display the recorded video when the VCR
advances through the block of marked commercials.

48

MOVIE " ADVANCE e

The Movie Advance feature helps you locate certain parts of
prerecorded movies (rented or purchased). This feature works

two ways: 1) you can go to the beginning of the movie, or, 2)
you can skip from one preview to the next. The feature works

only on cassettes recorded in the SP speed with the safety tab

removed.

1. To select the Movie Advance feature, insert a tape with the
safety tab removed and press SEARCH. The following menu

appears:

What type of tape
is this?

i i i i mill l i-_i..i -..ll iii _11n i -.11tn i_iI ill i_

2 Home Recording
3 Other

Press CLEAR to cancel

.

Press 1 if the tape is a purchased or rented movie,
press 2 if it's a recording made at home, or press 3 if
it's something else, you don't know, or you do not want

to use the Movie Advance feature.
Pressing 2 or 3 gives the same response and takes you to a

different search feature. If you accidentally make a wrong
selection, press STOpoEiECT on the VCR (STOP on remote)
and reinsert the tape. Press SEARCH.

If you press 1, the MOVIE ADVANCE menu appears.

.

MOVIE ADVANCE

Would you like to go to

the start of the movie

or to the next preview?

2 GO to preview

Press CLEAR to cancel

Press 1 to advance directly to the beginning of the movie or
press 2 to view the first (next) preview.

I(_(;flPr}tt('s {;n II(,X{ I),i_'l

The Movie Advance feature works
only on cassettes recorded in the

SP speed with the safety tab

removed.

MOVIE ADVANCE is a registered trademark of SRT, Inc.

49

(('¢lnhnued I_(_tn prevl_lu_ tl,lgl_;

• Press 1 to Go To Movie and bypass all previews. The

following screen appears with a blue background:

MOVIE ADVANCE

Searching for start

of movie..,

Rewinding tape

Press STOP to cancel

When the movie is found, the following screen is displayed:

MOVIE ADVANCE

The movie is ready.
Press PLAY to start.

Press STOP to cancel

• Press 2 to go to the first preview. The following screen
appears with a video background:

Searching for preview...

Press SEARCH to reverse
Press STOP to cancel

While the VCR is searching thorugh previews:

• Pressing SEARCH on the remote control reverses the

direction of the search.

• Pressing STOP cancels the preview search mode.

When a preview is detected, the VCR cues it and begins
playing.

Press SEARCH for next

While the VCR is playing a preview:

• Pressing SEARCH on the remote control will search and cue

the next preview.

Searching for Previews
While theVCR is searching for the

next preview, pressing SEARCH on
the remote control reverses the

direction of the search and
pressing STOP will cancel the

search.
After theVCR has found the

beginning of a preview and started
playing it, press SEARCH to

advance to the start of the next
preview.

50

PICTURE SEARCH OPTIONS

The most basic way to search during playback is using the
FORWARD or REVERSE buttons (FWD and REV on the VCR).

This section contains several other options available for
searching a tape.

FORWARD AND REVERSE SEARCH

You can search a tape during playback. Sound is turned off
during picture search, Search works well for tapes recorded at

the SP or SLP speed.

1. Press FORWARD (FWD) to search forward or REVERSE
(REV) to search in reverse.

2. Press FORWARD (FWD) or REVERSE (REV) again or press
PLAY to return to normal playback.

SLOW MOTION

You can view a tape during play or play-pause using slow
motion. Slow motion works well for tapes recorded at the SP or
SLP speed.

1. In pause mode, press FORWARD (FWD) or REVERSE (REV)
to start slow-motion playback.

2. Press FORWARD (FWD) to increase or REVERSE (REV) to
decrease the speed of the search.

3, Use TRACKING + or - to remove any streaks from the

picture.

4. Press PLAY to return to normal playback.
The VCR switches automatically from slow-motion playback

to stop after a few minutes.

51

FRAME ADVANCE

Frame advance lets you view one-stop action frame after
another during playback. Frame advance works well for tapes
recorded at the SP or SLP speed.

1. Press PAUSE on the remote (PLAY/PAUSE on the VCR to
freeze the action.

2. Press FR. ADV on the remote each time you want to wew
the next frame of the scene.

3. Press PAUSE or PLAY on the remote (PLAY/PAUSE on the
VCR) to return to normal playback.

VARIABLE SPEED USING THE

SHUTTLE RING

The shuttle ring on the VCR's front panel allows variable speed
searching during playback. The picture is best for tapes recorded

in the SPor SLP speed.

1. In play or still mode, turn the shuttle ring--clockwise for
forward or counterclockwise for reverse--to begin
searching. The farther you turn the dial, the faster the search
speed.

2. Press PLAY/PAUSE to turn off the shuttle feature and return
to normal playback.

ADDITIONAL NOTES ON THE
SHUTTLE DIAL:

Inthe stop mode, turn the shuttle ring more than half way

clockwise to start fast forward and turn the shuttle ring more
than halfway counterclockwise to start rewind.

• Some noise or streaks in the picture are normal during
searching.

• After three minutes in still or slow, the VCR will go into stop
mode.

Insert Tape:
Don't forget to insert a recorded

tape when using the search
features.

52

INDEX SEARCH

The VCR has a "VHS Index Search System" that automatically

records an index mark on the tape every time you start a

recording. During playback you can locate the program you
want to play by the number of index marks or by scanning. The
VCR will search forward or reverse from the location you are on

the tape.

TO SEARCH :

l. Press STOP.

2. Press SEARCH on the remote to display the INDEX SEARCH
screen on the TV screen.

3. If you want to search through a certain number of index
marks, press two number buttons to enter the number of
marks you want to search. Press CLEAR on the remote to

correct an entry.

4. Press FORWARD (FWD) to search forward or REVERSE

(REV) to search in reverse. The VCR will locate your index
mark and begin playback. If you did not enter a specific

index number, the VCR will locate the next index mark and
begin playback.

5. Press STOP to stop index searching.
Some index marks may be missed by the VCR:

• A mark too close to your location on the tape.

• The mark at the beginning of a recorded segment of five
minutes or less.

• The first index mark on the tape when you start at the
beginning of the tape.

GO-TO SEARCH

The Go-To Search feature enables the VCR to quickly locate a
counter reading anywhere on the tape. When the VCR locates

the counter reading, it will begin playback.

1. Press STOR

2. Press SEARCH on the remote until the GO-TO SEARCH menu
appears on the screen.

(Continues on next page)

INDEX SEARCH

Press REV or FWO
to begin scanning

OR

enter a specific

_ndex number

Press SEARCH to exit

INDEX SEARCH

Searching for
index number 12...

Press STOP to cancel

INDEX SEARCH

Searching for

index marks...

Press STOP to cancel

GO-TO SEARCH

Current tape counter is

2:17:25

Press REV or FWO

to go to -:--:00

Press SEARCH to exit.

53

r( flntinlu'd tronl prevunls pagel

3. Press number buttons to enter the hour(s) and/or minutes of
the counter reading you want the VCR to "go to". Press

CLEAR on the remote to correct an entry.

4. Press FWD to search forward or REVto search in reverse.

5. Press STOPto stop Go-To searching.

PRO-TECT PLUS TM LOCKING

FEATURE

GO-TO SEARCH

Current tape counter is

2:17:25

Press REV or FWD
to go to 0:00:00

Press SEARCH to exit,

To disable the usage of the VCR, or to protect your timer
recordings, you can lock the VCR so that the buttons on the

VCR or remote won't work.

To Lock: Press and hold either the remote control's
ON.OFF, VCR1, or VCR2 button (whichever controls your

VCR) until LOCK appears in the display. LOCK appears
when the feature is activated and if you attempt to turn on

the VCR while the feature is on.

To unlock the feature and turn on the VCR: Press and hold

either the remote's ON.OFF, VCR1, or VCR2 button
(whichever button your VCR is set to respond to) until LOCK

disappears.

TRACKING

Your VCR has automatic tracking which removes the streaks or

noise from the picture. Automatic tracking is activated when you
insert a tape or turn on the VCR. Occasionally you may need to

manually adjust tracking, especially if the tape was recorded on

a different VCR. Use the TRACKING buttons to remove the
streaks or noise. You can also use tracking when you PAUSE a

tape to reduce jittering of the picture.
When you manually adjust the picture, automatic tracking is

turned off. To turn automatic tracking back on, eject the tape
and reinsert it.

Tracking has no effect during recording--only playback.

LockingYour VCR:

If a timer recording is
programmed, make sure yourVCR
is turned off. Locking yourVCR
prevents theVCR from being
accidentally turned on.

54

TIME COUNTER

The time counter shows the actual time it takes to record a
program or play back a segment of a recorded tape. It helps

locate the beginning or end of l_rograms you taped. The time

counter resets to 0:00:00 whenever the tape is ejected from

the VCR.
For example, if you record a 30-minute program at the

beginning of the tape and you want to go to the end of that
program to begin another recording, you would:

1. Press INFO twice to display only the time counter.

2. Press CLEAR to reset the time counter to 0:00:00.

3. Press FORWARD (FWD) to forward the tape until the time
counter reads 0:30:00.

4. Press STOP. This is the approximate end of the program.

(You may want to press PLAY to verify.) Now, you can begin
recording at this spot.

5. Press the INFO button to remove the time counter from the
screen and return to the normal display mode.

ON-SCREEN DISPLAYS

The INFO button shows the status of the VCR (Stop, Play
Record, etc.), channel number, time counter, date, time, and

tape speed on the TV screen. The date and time must be set
before they can be displayed.

1. Press INFO to see the on-screen displays. The current time is
displayed in the VCR's display panel.

2. Press INFO again to have only the time counter remain on
the screen. The time counter is displayed in the VCR's
display panel.

3. Press INFO again to have no displays appear on the TV
screen. The time counter remains in the VCR's display panel.

This is useful for dubbing tapes.

4. Press INFO again to return to the normal display. The
current time is displayed in the VCR's display panel.

Turning off the VCR also resets the displays.

Hours Minutes

/

'b:3o=ooI

Seconds

Stop Ch gS gt30_gg

11/18/99 Thu 01:30PM SLP

On-screen display (times out)

0:3_100

Time counter only (does not time out)

3

No displays will appear (useful for
dubbing)

55

AUDIO SET-UP FEATURES

The audio setup features affect your tape playback and
recordings. The features in this section are accessed through the

AUDIO menu and are shown in the displays below.

1. Press MENU to bring up the VCR MAIN MENU.

VCR MAIN MENU

I VCR Plus+

2 Timer Recordings
3 Time
4 Channels
5 Setup

6 Preferences

8 Language

Q Exit

2. Press 7 to display the AUDIO menu.

AUDIO

II I •

2 Tape Playback: HI-FI

0 Exit

Now you are ready to select an item from the menu to set up.

RECEPTION

Some TV programs are broadcast with stereo audio or a second
audio program (SAP) which offers a second language. The

Reception feature lets you select the type of audio you want to
record. Press 1 to switch between Reception: STEREO, MONO,

and SAP.

• Select STEREO for normal or stereo broadcast TV recording.
The STEREO indicator _ights when the station you are tuned
to is broadcasting stereo.

• Select MONO if the stereo signal is weak and the sound is
too noisy.

• Select SAP to record a second audio program instead of the
normal audio on both the hi-fi and linear tracks.

56

TAPE PLAYBACK

The VCR records the same audio on both the Hi-Fi stereo and

linear tracks on the tape. Hi-Fi sound is recorded on separate
left and right stereo channels. Monaural sound is recorded on

the linear track. Press 2 to switch between Tape Playback: HI-FI,
LINEAR, and MIX.

To enjoy Hi-Fi sound, connect your VCR to a stereo television or
amplifier/receiver using the audio jacks. The Tape Playback
feature lets you select which audio you play back.

• Select HI-FI to play back sound recorded on the Hi-Fi tracks
and for normal use. The Hi-Fi indicator lights.

• Select LINEAR to play back the sound recorded on the linear
monaural track, such as a second audio program (SAP), or a

dubbed voice-over.

• Select MIX to p]ay back the sound recorded on both the

linear track and the Hi-Fi track, sound-on-sound. The Hi-Fi
indicator lights.

57

58

THINGS TO KNOW BEFORE

CONNECTING COMPONENTS

PROTECT YOUR COMPONENTS
FROM POWER SURGES

Connect all components before plugging any
power cords into the wall outlet.

Always turn off the TV and other components
before you connect or disconnect any cables.

POSITION CABLES CORRECTLY TO
AVOID AUDIO HUM OR INTERFERENCE

Insert all cable plugs firmly into their lacks.

Place the audio/video cables to the sides of the
TV's back panel instead of straight down the

middle after you connect your components.

Try not to coil any twinqead cables and keep
them away from the audio/video cables as much as

possible.

Make sure all antennas and cables are properly

grounded. Refer to the SafetyTips sheet packed

with your unit.

PROTECT YOUR COMPONENTS FROM

OVERHEATING

Do not block ventilation holes in any of the

components. Arrange the components so that air can

circulate freely.

Do not stack components.

Allow adequate ventilation when placing your

components in a stand.

Place an amplifier or satellite receiver on the top shelf of
the stand so heated air rising from it will not flow around
other components.

V

¥

V

¥

¥

V

7 CONNECTIONS

V

59

CONNECTING YOUR VCR

Refer to these pages to help you connect your VCR.

JACKS AND CABLES

RF JACKS AND ANTENNA CABLES
(F-TYPE)

The RF jacks provide good picture and mono sound quality, and

must be used if audio/video connections are not available for
your TV.

These jacks are required for antenna or cable-TV connections.
The RF jacks on the VCR are labeled IN FROM ANT. and OUT

TO TV. The antenna cable supplied with your VCR is used to
connect the VCR's OUT TO TV jack and your TV's antenna

input.

O

RF Jack

AUDIONIDEO JACKS AND CABLES
(RCA-TYPE)

The audio/video jacks provide very good picture and sound
quality, and can be used if your TV has audio/video input jacks.

These jacks are used for most audio/video connections between
components. The VCR audio/video jacks are color coded

(yellow for video, red for right audio, and white for left audio). If
your TV only has one input for audio (mono), you may need a Y-

adapter to hear sound from both channels.

Audio/VideoJack

6O

CHOOSING A VCR CONNECTION

There are several different ways to connect your VCR,
depending on whether or not you have cable service, if you

have a cable box to see this service, whether some of the cable
channels are scrambled, and so on.

Five connections are described in this section and one of them
should provide you with a VCR connection that works.

• TV with RF jack only

• TV with audio/video jacks

• TV with audio/video jacks and cable box to unscramble pay
channels only

• TV with RF jack and satellite receiver

• TV with audio/video jacks and satellite receiver

If you need to connect additional components not shown in the
diagrams here (and are unsure of how to connect them), refer to
the instruction manual that came with that particular

component.

ADVANTAGES OF" AUDIONIDEO CABLE

CONNECTIONS

Using a simple antenna cable connection gives you good
picture quality. If your television has audio/video jacks, it is
highly recommended to use them for even better picture quality

and stereo sound when recording and playing back videotapes.

These connections give you more convenient operation by not
having to share the TV's antenna signal.

DON'T FORGET ABOUT THE
AUTO TV/VCR FEATURE

The TV/VCR switch controls whether the picture signal is
coming from the VCR or the TV.

You can set the Auto TV/VCR feature to ON when using only the

IN FROM ANT. and OUT TO TV jacks and OFF when using the

AUDIO/VIDEO output jacks--so your TV signal is not

interrupted when the VCR is turned on. You can change the

setting manually by using the TV.VCR button on the VCR or the

ANTENNA button on the remote.

61

TV WITH RF JACK ONLY

This connection assumes:

• You are connecting antenna, cable, or cable box system.

• Your television has only an RF input jack.

This connection provides:

• Mono sound playback from VCR.

• Record one channel while watching another (except
when using a cable box for all channels).

To use this connection, you must have:

• One coaxial cable for cable or antenna connection; two
cables for a cable box

To connect:

1. Connect cables as shown.

2. Return to First Things First, then follow the steps.

Using This Connection

Tune your TV to channel 3 or 4, whichever one you selected
with the CH. 3/4 switch on the back of the VCR.

Auto TV/VCR Setting:

• Set the Auto TV/VCR feature to ON.

To play a tape:

1. Inserta tape.

2. If necessary, press PLAY.

To record one program and watch another:

1. Begin recordinga program using one of the
recording features.

2. Press the TVoVCR button on the VCR (ANTENNA on
remote) and select a different channel on the TV.

VCR

I

77/

I

CABLE, CABLE BOX, OR ANTENNA_

62

TV WITH AUDIONIDEO JACKS

This connection assumes:

• You are connecting an antenna, cable, or cable box system.
* Your television has audio/video jacks.

This connection provides:

• Stereo sound playback from VCR.

• Record one channel while watching another (except when
using a cable box for all channels).

To use this connection, you must have:

• (1) coaxial cable for cable/antenna connection; (2) for

cable box

(3) audio/video cables

To connect:

1. Connect cables as shown.

2. Return to First Things First, then follow the steps.

Using This Connection

Tune your TV to its video input channel. Use of TV,,VCR button
on the VCR (ANTENNA on remote) is not required.

Auto TV/VCR Setting:

• Set the Auto TV/VCR feature to OFF.

To play a tape:

1. Insert atape.

2. If necessary, press PLAY.

To record one program and watch another:

1. Begin recording a program using one of the

recording features.

2. Select a different channel on the TV.

VCR

CABLE, CABLE BOX, OR ANTENNA_

TV

63

TV WITH AUDIO/VIDEO JACKS AND CABLE BOX

TO UNSCRAMBLE PAY CHANNELS ONLY

This connection assumes:

• You are using a cable box only to unscramble premium

channels.

• Your TV has audio/video input jacks.

This connection provides:

• Stereo sound playback from VCR.

• Recording a scrambled or unscrambled channel through the

cable box while watching an unscrambled channel.

To use this connection, you must have:

• (3) coaxial cables

• (3) audio/video cables

• (1) splitter

To connect:

1. Connect cables as shown.

2. Return to First Things First, then follow the steps.

Using This Connection

Tune your TV to its video input channel. Use of TV•VCR button
on the VCR (ANTENNA on remote) is not required.

Auto TV/VCR Setting:

• Set the Auto TV/VCR feature to OFF.

To play a tape:

1. Insert a tape.

2. If necessary, press PLAY.

To record a scrambled or unscrambled program and watch
another unscrambled program:

1. Begin recording a scrambled or unscrambled program
through the cable box using one of the recording features.

2. Select an unscrambled channel on the TV.

I AII scrambled channels must be 1

viewed through theVCR.

For Cable Box Setup, select ALL
channels (see Setting Up the VCR).

CABLE

2-WAY E_

SPLITr

v

64

TV WITH RF JACK AND DIGITAL SATELLITE

RECEIVER

This connection assumes:

• You have a basic digital satellite system and your TV does

not have audio/video input jacks.

This connection provides:

• Mono sound playback from VCR, recordin from a satellite
receiver, and recording one off-air or cable channel while
watching another.

To use this connection, you must have:

• (4) coaxial cables and (3) audio/video cables

To connect:

1. Connect cables as shown.

2. Return to the First Things First Section, then follow the steps.
Using This Connection

• Tune your TV to channel 3 or 4, whichever one you selected

with the CH. 3/4 switch on the back of the VCR.

• To record and watch off-air or cable, tune your VCR to
channel 3 or 4 whichever one you selected with the CH3/

CH4 switch on the back of the receiver. Turn off receiver.

• To watch and/or record from the digital satellite receiver,
tune your VCR to its line input (L1 if you have connected the
receiver to the back jacks or L2 for the front jacks).

Auto TV/VCR Setting:

• Set the Auto TV/VCR feature to ON.

To play a tape:

1. Insert a tape.

2. If necessary, press PLAY.

To record one off-air or cable program and watch another

1. Turn off the digital satellite receiver and begin recording a
program using a recording feature.

2. Press TV.VCR on the VCR (ANTENNA on remote) and
select a different channel on the TV.

To record a digital satellite receiver program

1. Turn on the receiver, tune the VCR to its line input, and begin
recording a program using a recording feature.

Caution

The unauthorized recording of
satellite broadcasts, television

programs, or other copyrighted

materials may infringe the rights

of others.

CABLE,CABLE BOX OR ANTENNA"_

_t% SATELLITE SIGNAL _

65

TV WITH AUDIONIDEO JACKS AND DIGITAL

SATELLITE RECEIVER

This connection assumes:

• You have an advanced digital satellite system and your TV
has audio/video input jacks.

This connection provides:

• Stereo sound playback from VCR, recording from receiver
while watching cable or off-air channel, and recording one
cable or off-air channel while watching another.

To use this connection, you must have:

• (3) coaxial cables and (6) audio/video cables

To connect:

1. Connect cables as shown.

2. Return to the First Things First Section, then follow the steps.

Using This Connection

• Tune your TV to its video input to record (or watch) the VCR
or satellite receiver.

• To record from the digital satellite receiver, tune your VCR to

its line input (L1 if you have connected the receiver to the

back jacks or L2 for the front jacks).

Auto TV/VCR Setting:

• Set the Auto TV/VCR feature to OFF. Use of TV-VCR button

on the VCR (ANTENNA on remote) is not required.

To play a tape:

1. Insert a tape.

2. If necessary, press PLAY.
To record one off-air or cable program and watch another:

1. Begin recording a program using a recording feature.

2. Select a different channel on the TV.

1to record a digital satellite receiver program and watch a cable

or off-air channel:

1. Turn on the receiver, tune the VCR to its line input, and

begin recording a program using a recording feature.

2. Select a different channel on the TV.

66

This section gives you some additional information about
the VCR, including a description of the unit's controls

and displays.

You will also find the section, TroubleshootingT_ps,and a
question and answer section about Commercial Advance

in this Appendix.These areas might help resolve some of
those simple problems.

Finally, this section of the manual also contains your
warranty information.

V

V

V

¥

V

V

V

n 8 REFERENCE

67

FRONT PANEL

®

(Front Panel door open)

I

\

K(,nlot{, _(,n_or

AUDIO (R and L MONO) and VIDEO In Jacks Receives signals from another component like a VCR or
camcorder when it is connected to these jacks. Use INPUT to select L2 to record from these jacks.

CHANNEL*TRACKING and Up • and Down • Selects next higher or lower channel in the VCR's
channel memory. Adjusts tracking when a tape is playing. Used for program express and moving through
menu system.

CLEAR and Left 4 Resets time counter to 0:00:00. Allows you to change entries when setting the clock
or programming the timer. Used for program express and navigating through the menu system,

FWD Forwards the tape when the VCR is stopped. Searches the picture forward during playback. Starts

slow motion during play-pause and increases slow-motion speed.

INFO and Right • Displays information on the TV screen. Used for program express and navigating
through the menu system.

INPUT Selects between the line inputs and VCR's tuner. Line input refers to the signal coming from the
component connected to the audio/video input jacks on the back or front of the VCR.

MENU Displays and accesses VCR's menu system on the TV screen.

PLAY/PAUSE Plays a tape. Pauses action for viewing during playback. Pauses recording to prevent

recording of unwanted scenes,

PROG. EXP. Used for program express.
POWER Turns the VCR on or off.

RECORD Starts VCR recording. Used for express recording.
Remote Sensor Receives signals from the remote control. Aim the remote at this sensor.

REV Rewinds the tape when the VCR is stopped. Searches the picture in reverse during playback. Starts

slow motion during play-pause and decreases slow-motion speed.
Shuttle Ring Turn clockwise to search forward or counterclockwise to search in reverse. Turn farther

(over halfway) clockwise to fast forward or farther counterclockwise to rewind.
STOP ° EJECT Stops the normal functions such as record, playback, rewind, fast-forward, or pause. Also

ejects a stopped tape if pressed and held for a few seconds.

TAPE SPEED Selects a recording speed (either SP or SLP).

TV.VCR Switches the picture signal so that it either comes from the VCR or the TV cable/antenna signal.

68

DISPLAY PANEL

PWRTIMERHI-FI VCR

PLR_ ' nn.nn,

UU. I_lU PM

FuilcticJns ('/ock/Ci1uilter

Clock/Counter Displays current time, time counter, tape speed, or channel numbers when switching
channels.

FUNCTION DISPLAYS:
BYE Power off

CLOCK, TIMER, CHAN, START, END, DATE, SAVE, SAVED, RVIEW, CANCEL, 0-LAP Appear during

Express Recording.

DOwN & LOAD Front display alternates between these two words when AIISet data is being downloaded.
EJECT Displays when a videocassette is being ejected.

FFWD Fast forward
HELLO Power on

LOCK Appears for Pro-Tect Plustm locking feature
MARK COM Appears when the Commercial Advance feature is forwarding through commercials.

PLAY Tape is in playback mode.
REC Displays when the VCR is recording.

REC-P Paused recording.
REW Rewind

SRCH+ Forward picture search
SRCH- Reverse picture search

STILL
SLOW

STOP
T-REC

X-REC

Playback is paused; still-frame displayed

Tape playing back in slow motion

Tape is in stop mode

Timer recording in progress

Express recording in progress

Hi-Fi Indicator Lights when HI-FI or MIX is selected in the audio menu.

PWR Displays when the VCR is powered on.

TIMER indicator Displayed when Express Recording (XPR) or timer recording is under way or when the

VCR is set for a timer recording and the power is turned OFE "TIMER" flashes on the VCR front panel when
a timer recording is set and no tape is inserted in the VCR.

VCR Indicator (Applies only if the VCR Viewing Channel is 3 or 4). Press the TV.VCR on the VCR
(ANTENNA on remote) to turn on or off.

• VCR indicator on: Picture from VCR.

• VCR indicator off: Picture from TV channel.

69

BACK PANEL

[ '11IG_LT___N IL R_T

CH. 3/4 switch Determines the channel to which the TV must

be tuned in order to see the VCR's picture. Not used when
connecting the VCR to the TV using Audio/Video cables.

AUDIO (R and L/MONO) and VIDEO IN jacks Receives
signals from another component, such as a VCR or camcorder,
when connected to these jacks. Use the INPUT button on the
VCR or remote control to select the video line input (L1) and
record from these jacks.

AUDIO (R and L) and VIDEO OUT jacks Sends signals from
the VCR to another component, _ike a TV or VCR, when the
other component is connected to these jacks.

IN FROM ANT. jack Receives a signal from an antenna or

cable system when the VCR is attached with RF cables.

OUT TO TV jack Passes signal to TV using the supplied RF

cabEe.

7O

QUESTIONS AND ANSWERS ABOUT

THE COMMERCIAL ADVANCE FEATURE

WILL COMMERCIALS BE SCANNED THROUGH ONLY ON PLAYBACK OF RECORDINGS?

Yes. Tile VCR does not rewind and mark commercial segments until after recording is finished.

How FAST DOES A COMMERCIAL ADVANCE VCR SCAN THROUGH COMMERCIALS?

In SLP tape speed, a 3-minute commercial break is scanned through in approximately 8-12 seconds. In SP,it
takes about 25-35 seconds.

ARE COMMERCIALS STILL RECORDED IF I WANT TO WATCH THEM?

Yes. The recorded program, including commercials, can be viewed by setting the Playback feature to
MANUAL.

WHAT IF THE VCR SCANS FORWARD THROUGH PART OF MY PROGRAM?

To start skipping override, while the VCR is skipping press PLAY on the VCR or remote control. Then, press

rewind to go back to a point before the skipping started and press PLAY on the VCR or remote control.

Automatic skipping will start again once Commercial Advance detects the segment is over.

ONCE A RECORDING HAS BEEN MARKED, DOES THE COMMERCIAL ADVANCE FEATURE
WORK EACH TIME THE TAPE IS PLAYED?

Yes. If the Playback feature is set to AUTO, the marked commercials should be skipped each time the tape is
played in a COMMERCIAL ADVANCE VCR.

AFTER MARKING COMMERCIALS, IS THE TAPE LEFT AT THE BEGINNING OR END OF THE
RECORDING?

The tape is left at the end of the recording so it is in position to begin additional programmed recordings.

DOES THE MARKING PROCESS INTERFERE WITH OTHER PROGRAMMED RECORDINGS?
No. If two or more recordings are programmed together without sufficient time to mark the first recording,

marking will take place after all recordings are completed.

WHAT HAPPENS IF THE MARKING PROCESS IS INTERRUPTED?

Marking can be interrupted to allow use of the VCR. Marking will resume again when the VCR's power is

turned off as long as the tape has not been ejected from the VCR.

DOES THIS FEATURE WORK IN ALL RECORDING SPEEDS?

Yes, COMMERCIAL ADVANCE works in SP and SLP.

WILL COMMERCIAL ADVANCE MARKED RECORDINGS WORK IN NON-COMMERCIAL

ADVANCE VCRs?

A recording marked with the Commercial Advance feature will play in a VCR that doesn't offer this feature,
but commercials will not be automatically skipped.

71

TROUBLESHOOTING TIPS

NO POWER

• Check to make sure it is plugged into an operating outlet.

• Check to make sure your connections are correct.

VCR DOES NOT RESPOND TO REMOTE

• Press VCR1 (VCR2) to set remote to con.trol the VCR.

• Check to make sure there are no objects between the VCR and remote.

• The batteries may need changing.

• Make sure to press the VCR1 or VCR2 button on the remote to operate the VCR--whichever one
corresponds to the Remote VCR1/VCR2 setting.

• Remove batteries for at least one minute, then replace them. This resets the remote, so it may require
reprogramming.

REMOTE NO LONGER CONTROLS A PROSCAN, RCA, OR GE TV

• PressTV to set remote to control a compatible TV.

• Check to make sure the remote is programmed to control an ProScan, RCA, or GE TV.

POOR OR NO PICTURE FOR NORMAL TV VIEWING

• Check to make sure the VCR indicator is off.

• Check to make sure the TV is switched to an active channel.

• Check to make sure the antenna connections are secure and correct.

NOISY OR NO PICTURE DURING PLAYBACK

• Press TV•VCR on VCR (ANTENNA on remote) to turn VCR indicator on.

• Check TV channel selected (3 or 4) to make sure it matches the channel selected with CH. 3/4 switch on
back of VCR.

• Check to make sure the TV's fine tuning is correct for the channel you have selected.

• Check video cable connections between VCR and TV monitor.

• Check to make sure the TV monitor is set to video input.

• Try another tape.

• Some noise/streaks are normal during search, stop action, frame advance, and slow-motion playback.

STREAKS IN PICTURE DURING NORMAL PLAYBACK

• Press one of the TRACKING buttons to move streaks up or down for the best picture.

• Check to make sure the tape is of good quality and not worn out.

TIME COUNTER NOT WORKING OR TIME COUNTER NOT WORKING IN SEARCH MODES

• The time counter does not advance during unrecorded portions of tape. When an unrecorded segment of
tape is encountered, the time counter will hold its count until recorded material is detected again.

• A minus ( ) will appear in front of the time if you rewind the tape farther back than a counter reading of
0:00:00.

72

WILL NOT RECORD OR PLAY

• Check to make sure there is a tape in the VCR.

• Try ejecting and reinserting the cassette.

• Check to make sure the tape is not broken.

• Check to make sure the VCR is not in pause hlode. Press PAUSE or PLAY to return to
normal playback.

• Check the Pro-Tect PlusTM feature.

WILL NOT RECORD

• Check to make sure the safety tab is intact.

REWIND DOES NOT OPERATE

• Check to make sure the tape is not already rewound,

VCR PLUS+ OR TIMER RECORDING NOT MADE OR WRONG PROGRAM RECORDED

• Check to make sure the correct VCR Plus+ code is entered.

• Check to make sure the cable box or satellite receiver was turned on when recording was
to begin.

• Check to make sure the program was entered correctly (wrong channel or times).

• Power interruption. Reset the clock.

• Check to see if time and date are correct--including AM/PM.

• Check to make sure the program did not exceed the tape's length or the tape was not

rewound beforehand.

• Check to make sure the VCR was turned off at the time recording was to start.

• Check to make sure there was a tape in the VCR and the cassette's safety tab was intact.
* VCR ejects cassette when the end of the tape is reached during a timer recording.

• Check to make sure VCR Plus+ setup was completed correctly.

CLOCK SHOWS INCORRECT TIME OR DATE

• Power interruption. Automatic clock set was not turned on or did not work properly.
Check time zone and daylight-savings settings.

• Make sure VCR or cable box is tuned to channel carrying XDS information.

• Auto clock set is not supported by digital satellite receivers. Set the clock manually.

TIME DID NOT ADJUST FOR DAYLIGHT-SAVING TIME

• Check to make sure daylight-saving feature is set correctly.

VCR MAKES NOISE WHEN STOPPED

• VCR is removing tape from heads. This is normal. The head cylinder inside the VCR will
continue to rotate for a few minutes after you put the VCR in the stop mode.

WILL NOT AUTO CHANNEL SEARCH ACTIVE CHANNELS CORRECTLY

• Check to make sure the antenna connections are secure and correct.

• Check to make sure the Signal Type: CABLE/ANTENNA feature is set correctly.

• If Detect Automatically was selected for the Signal Type in the AUTO CHANNEL SEARCH

menu, try using either CABLE TV or ANTENNA instead.

• May riot be necessary if using a cable box for all channels. Contact your local cable

company for more information.

73

TAPE PLAYS BACK IN SLOW MOTION

• Press PLAY to return to normal playback.

CASSETTE WITH SAFETY TAB REMOVED DOES NOT START TO PLAY AUTOMATICALLY

• Check to make sure the Auto Play ON/OFF feature is set to ON.

TIMER OR TAPE INDICATOR FLASHES

• Check to make sure there is a cassette in the VCR when a timer recording is set.

TIME COUNTER DISAPPEARS DURING SEARCHING

• This is normal.

ON-SCREEN MENUS APPEAR IN A FOREIGN LANGUAGE

• Check LANGUAGE feature to choose desired on-screen language.

NO STEREO SOUND DURING PLAYBACK

• Check to make sure the Tape Playback feature is set to HI-FI to hear stereo sound during
playback.

• Must use the AUDIO/VIDEO jacks on the back of the VCR to hear stereo sound.

STEREO AUDIO TOO NOISY

• Stereo signal is weak. Set Reception: STEREO/SAP/MONO feature to MONO.

• Press one of the TRACKING up or down buttons to minimize the noise.

INDEX AND ZERO SEARCH FEATURES DO NOT OPERATE

• Check to see if MOVIE ADVANCE feature is activated.

CANNOT ACCESS MOVIE ADVANCE FEATURE

• The video cassette must have the safety tab removed and the recording must be in SP speed.

• Home recording was selected for the tape type in the on-screen display. Eject cassette and
reinsert.

VCR FORWARDS THROUGH COMMERCIALS OR MOMENTARILY DISPLAYS A BLUE
SCREEN DURING PLAYBACK

• Commercial Advance feature is set to AUTO. Set it to MANUAL.

COMMERCIAL ADVANCE FEATURE DOES NOT MARK COMMERCIALS WHEN:

• The marking feature is set to OFF in the commercial advance menu. Set it to ON.

• A recording is less than 15 minutes or the commercial is longer than one minute.

• A single isolated commercial can not be marked.

• Recording started in the middle of a commercial segment.

• Acommercial group within the first or last two minutes of a recording.

• Accuracy and effectiveness can vary depending on the program content and the characteristics

of the commercials.

• A commercial is between 30-and 45 seconds and 4S-and 60 seconds.

• Effectiveness may vary when local television stations insert their own commercials.

COMMERCIALS RECORDED EVEN THOUGH COMMERCIAL ADVANCE FEATURE WAS

SET TO ON.

• Commercial advance is designed to record the commercials, mark them, and then skip over

them during playback.

74

HOW TO FIND YOUR TV's

VIDEO INPUT CHANNEL

You need to tune your TV to the Video Input Channel if you are

using the VCR's AUDIO/VIDEO OUT jacks to connect to the
TV's AUDIO/VIDEO INPUT jacks. You must select this
"channel" before you can see the VCR's menus, the cable or
antenna reception, and the content that's on a tape.

The Video Channel on TVs varies for different brands and
different models. Below are some steps to try:

• If your TV brand is RCA, GE, or PROSCAN, press the TV
button on the remote control that came with the VCR. Then

press the INPUT button on the remote.

• If you have another brand of TV, consult the section,

Programming The Remote, to see if the VCR's remote

contro{ can be set to control your TV. If so, follow the step

above.

If those options do not work, try the following ideas. You might
access the Video Input Channel by:

• pressing a button on the remote (see table below)

• selecting the channel from the TV's menu system
(see table below)

• tuning directly to the channel by selecting a specific
channel number (see table below)

• going through all the channels in the channel list by
pressing the channel up or down buttons on the TV.

Some common scenarios are listed in the Video Input Channel
Variations table that follows:

Video Input Channel Variations

Button/Switch Button on the Channel
on the TV TV Remote Number

VIDEO VID 1 00
SIGNAL LINE 90

VID I VID 91
VID 2 VIDEO 92

S-VID S-VID 93
S-VIDEO INPUT VID I

S-VIDEO VID 2
SOURCE

AU×

INPUT
Button

TV Button

VCA1 ON'OFF

DVD VCR2 AUX SAT.CABLE

MUTE SEAROH

®

@

SPEED _ GO BACK

GUIDE INFO

0 :20

MENU CLEAR

QC>

RECORD STOP PAUSE

-TRACKING+ EDIT FRADV

0000

75

SPECIFICATIONS

Format:

Record/Playback

System:

system

Video Signal System:
Antenna:

Tuner:

Type:

Power Requirement:
Power Consumption:

Dimensions:

Weight:

Other:

StorageTemperature
Range:

Operating
Temperature Range:

VHS
Video: 4-head

Audio: VHS Hi-Fi record/playback

EIA standard: NTSC color
75-ohm external VHF/UHF combined

antenna terminal

USA: 181 channels capability*

(125 cable channels)

Canada: 178 channels capability*

(122 cable channels)

AutoProgramming frequency synthesis

120V AC, 60 Hz
17 watts (standby < 3.3 watts)

3.7 inches high (94 mm)
17 inches wide (432 mm)

9.57 inches deep (243 mm)

7.1 pounds (3.2 kg)

Automatic head cleaner

- 22°F to +149°F

(-30°C to +65°C)
+41°Fto +104°F

(+5°C to +40°C)

*Check your cable company's compatibility requirements.

CLEANING THE VCR

Use a soft cloth or dusting attachment of your vacuum cleaner
to dust your VCR. Remove dust from the ventilation holes on the

top, back, sides, and bottom of the cabinet.
Plastic surfaces are easily scratched and can be marred by

alcohol and various solvents. Avoid excessive use of oil-based
furniture polishes since the materials used in the cabinet will
accumulate more dust. We recommend using a nonabrasive,

antistatic cleaner and polisher.

Specifications are subject tochange without notice. ]

76

LIMITED WARRANTY

What your warranty covers:
Any defect in materials or workmanship.

For I_ow long after your purchase:

• 6 months for labor charges.

• One year for parts.

The warranty period for rental units begins with the first rental or 45 days from date of shipment to the

rental firm, whichever comes first.

What we will do:

• Pay any Authorized ProScan VCR Service Center the labor charges to repair your VCR.

• Pay any Authorized ProScan VCR Service Center for the new or, at our option, refurbished replacement
parts required to repair your VCR.

How you get service:

• Take your VCR to any Authorized ProScan VCR Service Center. To identify your nearest Authorized

ProScan VCR Service Center, ask your dealer, look in the Yellow Pages, or call 1-800-PROSCAN.

• Show the Authorized Service Center Representative your evidence of purchase date or first rental.

• Pick upyour VCR when repairs are completed.

What your warranty does not cover:

• Customer instruction. (Your Owner's Manual clearly describes how to install, adjust, and operate your

VCR. Any additional information should be obtained from your dealer.)

• Installation and related adjustments.

• Signal reception problems not caused by your VCR.

• Damage from misuse or neglect.

• Cleaning of video/audio heads.

• Batteries.

• A VCR that has been modified or incorporated into other products or is used for institutional or other
commercial purposes.

• AVCR purchased or serviced outside the U.S.A.

• Acts of God, such as but not limited to lightning damage.

Product Registration:

• Please complete and mail the Product Registration Card packed with your VCR. It will make it easier to
contact you should it ever be necessary. The return of the card is not required for warranty coverage.

How State Law relates to warranty:

• This warranty gives you specific _egal rights, and you also may have other rights that vary from state to

state.

If you purchased your VCR unit outside the United States:

• This warranty does nol apply. Contact your dealer for warranty information.

Service calls that do not involve defective materials or workmanship are not covered by this warranty.
Costs of such service calls are the sole responsibility of the purchaser.

77

GLOSSARY

AutoEdit Lets you control two VCRs simuhaneously with a
single remote. Useful when making a copy of a video tape.

A/V Cables & Jacks Commonly called "RCA-type" cables.
Improves picture and sound quality. Required for stereo audio.

Code Search Simplifies programming the [emote control by not
requiring you to identify and enter a code to operate a

component.
Commercial Advance Lets you skip commercials during video

tape playback.

EnergySaver Automatically turns the VCR off after a (user
definable) period of inactivity, cutting energy consumption.

Express Recording (XPR) A method of timer recording that lets
you tape the remaining portion of a program.

Movie Advance Helps you locate certain parts of prerecorded

movies (rented or purchased).
Program Express Lets you quickly program a timer recording

using the VCR's front panel buttons instead of the on-screen
menu.

Pro-Ted Plus TM Allows you to "lock" the VCR so that the front
panel and remote control buttons don't work. Useful for

protecting timer recordings.

QuickSet Guide An interactive, menu-based guide which helps
you set up a number of your VCR's features. Also accessible

through the main on-screen menu.
SAP (Second Audio Program) A second sound track that may

be included with a stereo broadcast. Usually used for foreign

language dubs of programs.

Shuttle Ring A control on the VCR's front panel that allows
variable-speed control of picture search.

VCR Channels List A "list" of channels you want the VCR to be
able to tune when using the CH+/- buttons.

VCR Plus+ Simplifies timer recording by entering a PlusCode

Programming Number from an available TV listing.

XPR See Express Recording.

78

A C D

Accessories

included 4

ADD/REMOVE CHANNELS

screen 12

ANTENNA button

19, 25, 36, 61, 62, 63, 64, 65,

66
Arrow buttons 6, 24, 25, 68
Audio

playback type 56
selecting 56

Audio code list 42

Audio features, set up 56
AUDIO menu 56

Audio only

playing back 37
recording 36

Audio/Video (A/V) jacks

5, 36, 37, 60, 61, 63, 64, 66,

68, 70, 75
Auto channel search 10
Auto clock feature 12

Auto play feature 19, 27
Auto'rV/VCR feature

19, 61, 62, 63, 64, 65, 66

AutoEdit feature 38
Automatic rewind 27
Automatic tracking 27, 54

AUX button 24, 42

AUX button codes 43
Auxiliary component codes 42

Auxiliary component codes for

remote 43

B

Back panel jacks 70

Back-lit remote 24
Basic recording 28

Basics, learning 23
Batteries

installing in the remote 4

Broadcast stereoTV recording 36
BYE display 69

Cable box codes 43
Cable box setup 9

Cables

positioning 59
types of 60

CH + and _ buttons

25, 26, 40, 42

CHAN buttons II I-
Channel 3/4 switch 5, 62, 65

r.

CHANNEL buttons 12, 68

ChanneI,VCR viewing 5
Channels, adding/removing 12

CHANNELS menu 9, II, 16, 33
Choosing aVCR connection 6 I

CLEAR button

25, 26, 34, 41, 53, 55, 68

Clearing timer programs 35

Clock display 69 F
Code search feature 40

Codes for remote 43
Commercial Advance 46

display 48
marking 47

menu 47
playback 48

questions and answers 71

Component buttons 24
Connecting yourVCR 4

Connections 59

audio/video cable 6 I
choosing 61 G

TV with A/V jacks, cable box 64
TV with A/V jacks 63

TV with A/V jacks, satellite

receiver 66
TV with RF iack only 62
TV with RF jack, satellite re-

ceiver 65

twoVCRs 37 H

Controls

back panel 70
front panel 68

Copying and editing tapes 37

Date and time setting 12
Design specifications 76

Display panel 69

Displays, on screen 55
Dual remote with AutoEdit 38

DVD button 24

EDIT button 25, 38
Editing timer programs 35

EJECT button 27
Eject, tape 27

EnergySaver feature 19
Express Recording (XPR) 30

FADV button 25

Fast forward (shuttle ring) 52
FFWD display 69

FORWARD button

25, 27, 40, 42, 51, 53, 55

FRADV button 52

Frame advance 52
Front panel controls 68

FWD button

37, 38, 51, 53, 55, 68

Glossary 78
GO BACK button 25, 26

Go-To search 53
GUIDE button 26

HELLO display 69
Hi-Fi indicator 69

7g

I

IN (FROM ANT) jack

4, 5, 6, 19, 37, 60, 61, 62,

65, 70

Included accessories 4
Index search 53

Indicators in display panel 69
INFO button 15, 25, 26, 35, 55

INPUT button

5, 25, 32, 36, 37, 68, 75

J

Jacks

Audio/Video (A/V) 75

Jacks, types of 60

L

LI indicator 36, 37, 65, 66
L2 indicator 36, 37, 65, 66

LANGUAGE

choosing 6

LANGUAGE menu 8
LED on remote 40

Left and right buttons 35, 68
Light button 24

LOCK display 54, 69
Locking feature 54

M

MappingVCR Plus+ Programming

System Channels Manu 16

MENU button

68_ 1OII, 12 i:_ 14 16 182531,

32, 33, 34, 35, 46, 56, 68

MOVIE ADVANCE 49
MUTE button 26

N

Number buttons 6, 15, 25, 26

O

OK button 24
ON'OFF button

24, 25, 26, 40, 42, 54
On-screen displays 55
OUT (TO TV)jack

4,5,_ 19, 37, 60, 6i, 62, 65, 70

Overheating 59

P

PAUSE button

25, 27, 28, 37, 38, 52, 54

Picture search options 51
PLAY button

2_ 27, 37, 3a 4Q 51, 52, 6Z 63,

64, 65, 66

PLAY display 69
PLAY/PAUSE button 52, 68

Playing a tape 27
Plugging in theVCR 4

PlusCode number 33
POWER button 27

Power surges 59
PREFERENCES menu 18, 19, 46

Pro-Tect Plus locking feature 54

Problem solving 72
PROG EXP button 31, 68

Programming the remote 39

cable boxes 40

satellite receivers 40

TVs 40

Programming the remote to

Control an Audio compone

auxiliary component 42

PROGRAMS OVERLAP message

32, 34

Q

QuickSet guide 5, 8

R

REC button 38
REC display 69

Reception: STEREO/MONO/SAP

feature 36, 56

RECORD button

25, 28, 30, 36, 38, 68

Recording

audio only 36
basic 28

broadcast stereo TV 36
copying and editing tapes 37

Express (XPR) 30

options 29

program express 31
SAP 36

speeds 20

timer 3 I

timer withVCR Plus+ 33

Remote

buttons 24

installing batteries 4
programming for other compo-

nents 40

sensor 68

Remote codes 43
Remote codes (other compo-

nents) 43

Remote VCR I/VCR2 18
Removing/adding channels 12

REV button 37, 68
REVERSE button

25, 27, 41, 42, 51, 53

Review programs screen 35
Reviewing timer programs 35

REW display 69
Rewind (shuttle ring) 52

Rewind, automatic 27

S

Safety tab 19, 28, 31

SAP,recording 36
SAT,CABLE button 24, 40

80

Satellite receiver codes 43
Search

forward 5I
reverse SI

SEARCH button 26, 53
searchingtapes

Go-To 53

Sensor, remote 68
Set up

auto playfeature 19

autoTV/VCR feature 19
cable box 9

daylight-savings 13

EnergySaver feature 19

features in PREFERENCES menu

18

front panel (VCR display) 20

language feature 8
remoteVCRI/VCR2 option 18

tape speed feature 20
time and date 12

time and date manually 14
time zone 13

using menu system 8
VCR Plus+ channels 16

Shuttle ring 52, 68
Signaltype

changing II
selecting I I

Skipping commercials 46
SLOW display 69

Slow motion 5 I
Solving problems 72

Specifications 76
SPEED button

20, 26, 28, 30, 34, 36

Speeds, recording 20
SRCH+ and - display 69

STILL display 69
STOP button

;_ 2_ 3_ 3_ 3_ 37, 3_ 41, 53,

55, 68
STOP display 69
Stopping a timer recording 35

T

T-REC display 69
Tab, safety 28

TAPE display 32, 34
Tape eject 27

Tape playback feature 57
Tape playback: HI-FI/LINEAR/MIX

57

Tape, playing a 27
Tape speeds 20

Time and date setting 12
Time counter 55

Time counter display SS, 69

Time display onTV 55

TIMEmenu 13, 14

Time setting

set daylight saving 14
set time zone 13

TIMER display 32, 34
Timer programs

clearing 35

editing 35
reviewing 35

Timer recording 31

stopping 35

Timer recording (VCR Plus+) 33

TIMER RECORDINGS menu

31, 35
Tips, troubleshooting 72
Tracking 54

TRACKING buttons

26, 27, 51, 54, 68
Troubleshooting tips 72

TV button S, 24, 40, 75

TV codes for remote 43
TV function buttons 26

TVoVCR button

19, 36, 61, 62, 63, 64, 65, 66

TV's video input channel 75

U

UNRECOGNIZED NUMBER...

message 34

Up and down buttons 3I, 35

V

Variable speed search 52
VCR button 5

VCR channels list 10

VCR function buttons 25-26

VCR indicator 19, 36, 69

VCR MAIN MENU

5, & _ 9, 13, 14, I_ I_ 31, 33,
35, 46, 56

VCR Plus+

channel list menu t6, 33
channels 16
PlusCode number 34

recording 33

system channel numbers 16
VCR PLUS+ menu 33

worksheet for channels 17

VCR Plus+ GOLD Programming

System 15

VCR viewing channel 5, 27
VCRI button 18, 19, 24, 38, 54

VCR2 button 18, 24, 38, 54
Viewing channel 5, 69

VOL buttons 26

X

X-REC display 69

81

82

83

84

85

PROSCAN

An RCA Entertainment Product

If your VCR needs service, please contact your dealer or the
nearest Service Center from the yellow pages. Please do not

send any products to the Indianapolis address listed in this
manual or on the carton. This will only add delays in service

for your product.

€4_"n.IOMSON CONSUMER ELECTRONICS

10330 North Meridian Street
Indianapolis, IN 46290

© 2000 Thomson Consumer Electronics, Inc.

Trademark(s)® Registere_
Marca(s) Registrada(s) MODEL #:

Printed in the U.S.A. PSVR85

TOCOM 15530170 15530170

As an ENERGYSTAR®Partner, Thomson Consumer
Electronics has determined that this product or

product model meets the ENERGYSTAR®guidelines

for energy efficiency.